linux.git, branch v5.4.30 Clone of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git Linux 5.4.30 2020-04-02T13:11:03+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2020-04-02T13:11:03+00:00 ad13e142e024aa194016a32de8b9ba058fe9a6af 






arm64: dts: ls1046ardb: set RGMII interfaces to RGMII_ID mode
2020-04-02T13:11:03+00:00

Madalin Bucur
madalin.bucur@oss.nxp.com

2020-03-16T12:05:58+00:00

9e62b6673d14512790735639cc0f3a28079e9a67

commit d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.

The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.

Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".

Changing the phy-connection-type to "rgmii-id" to address the issue.

Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit d79e9d7c1e4ba5f95f2ff3541880c40ea9722212 upstream.

The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.

Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".

Changing the phy-connection-type to "rgmii-id" to address the issue.

Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








arm64: dts: ls1043a-rdb: correct RGMII delay mode to rgmii-id
2020-04-02T13:11:03+00:00

Madalin Bucur
madalin.bucur@oss.nxp.com

2020-03-16T12:05:57+00:00

c399a50ae87815c61b0c70a8038c66cbd026e97a

commit 4022d808c45277693ea86478fab1f081ebf997e8 upstream.

The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.

Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.

Changing the phy-connection-type to "rgmii-id" to address the issue.

Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit 4022d808c45277693ea86478fab1f081ebf997e8 upstream.

The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.

Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.

Changing the phy-connection-type to "rgmii-id" to address the issue.

Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








ARM: dts: sun8i: r40: Move AHCI device node based on address order
2020-04-02T13:11:03+00:00

Chen-Yu Tsai
wens@csie.org

2020-03-10T17:47:07+00:00

5aa29219206ad5f6e6d3e3f2729c32caab8b6cad

commit fe3a04824f75786e39ed74e82fb6cb2534c95fe4 upstream.

When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.

Move the device node to before EHCI1, where it belongs.

Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit fe3a04824f75786e39ed74e82fb6cb2534c95fe4 upstream.

When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.

Move the device node to before EHCI1, where it belongs.

Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








ARM: dts: N900: fix onenand timings
2020-04-02T13:11:03+00:00

Arthur Demchenkov
spinal.by@gmail.com

2020-03-08T19:19:33+00:00

8f1199341837acfcee4f2155c73ea6990bf68820

commit 0c5220a3c1242c7a2451570ed5f5af69620aac75 upstream.

Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.

Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit 0c5220a3c1242c7a2451570ed5f5af69620aac75 upstream.

Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.

Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
2020-04-02T13:11:03+00:00

Marco Felsch
m.felsch@pengutronix.de

2020-02-27T11:02:46+00:00

89ecba47b39158d0d7548adeb8358386460bdc9a

commit 636b45b8efa91db05553840b6c0120d6fa6b94fa upstream.

The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).

Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit 636b45b8efa91db05553840b6c0120d6fa6b94fa upstream.

The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).

Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
2020-04-02T13:11:02+00:00

Nick Hudson
skrll@netbsd.org

2020-03-12T09:03:45+00:00

bb4ec20d16874cc8ec1b4979d710671dadc5a132

commit 6687c201fdc3139315c2ea7ef96c157672805cdc upstream.

Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.

Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit 6687c201fdc3139315c2ea7ef96c157672805cdc upstream.

Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.

Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








ARM: dts: oxnas: Fix clear-mask property
2020-04-02T13:11:02+00:00

Sungbo Eo
mans0n@gorani.run

2020-03-21T14:36:53+00:00

e58eb564e1fc651611be5862b313e38d0b5d5fd1

commit deeabb4c1341a12bf8b599e6a2f4cfa4fd74738c upstream.

Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.

Fixes: 84316f4ef141 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes: 38d4a53733f5 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit deeabb4c1341a12bf8b599e6a2f4cfa4fd74738c upstream.

Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.

Fixes: 84316f4ef141 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes: 38d4a53733f5 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








perf map: Fix off by one in strncpy() size argument
2020-04-02T13:11:02+00:00

disconnect3d
dominik.b.czarnota@gmail.com

2020-03-09T10:48:53+00:00

a1081413e834508938949d2896eae97c2105e4f4

commit db2c549407d4a76563c579e4768f7d6d32afefba upstream.

This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:

        strncmp(filename, "/system/lib/", 11)

the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".

This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.

Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries")
Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Keeping <john@metanate.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Lentine <mlentine@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit db2c549407d4a76563c579e4768f7d6d32afefba upstream.

This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:

        strncmp(filename, "/system/lib/", 11)

the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".

This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.

Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries")
Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Keeping <john@metanate.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Lentine <mlentine@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>








arm64: alternative: fix build with clang integrated assembler
2020-04-02T13:11:02+00:00

Ilie Halip
ilie.halip@gmail.com

2020-03-19T21:45:28+00:00

451bf4d9592aca43e6cd025577399fa712c937d6

commit 6f5459da2b8736720afdbd67c4bd2d1edba7d0e3 upstream.

Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
    <instantiation>:2:2: error: unrecognized instruction mnemonic
     _ASM_EXTABLE 9999b, 9f
     ^
    arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
    user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
    ^

While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.

Also checked that the generated assembly matches the GCC output.

Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>






commit 6f5459da2b8736720afdbd67c4bd2d1edba7d0e3 upstream.

Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
    <instantiation>:2:2: error: unrecognized instruction mnemonic
     _ASM_EXTABLE 9999b, 9f
     ^
    arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
    user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
    ^

While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.

Also checked that the generated assembly matches the GCC output.

Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core")
Link: https://github.com/ClangBuiltLinux/linux/issues/924
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>