linux.git/arch/arm/boot, branch v3.16.81 Clone of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git ARM: dts: exynos: Fix interrupt for shared EINTs on Exynos5260 2019-09-23T20:11:33+00:00 Stuart Menefy stuart.menefy@mathembedded.com 2019-02-19T13:03:37+00:00 435d3ac023e76ae4b198b54b9d3ef8206aea30a2 commit b7ed69d67ff0788d8463e599dd5dd1b45c701a7e upstream. Fix the interrupt information for the GPIO lines with a shared EINT interrupt. Fixes: 16d7ff2642e7 ("ARM: dts: add dts files for exynos5260 SoC") Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit b7ed69d67ff0788d8463e599dd5dd1b45c701a7e upstream.

Fix the interrupt information for the GPIO lines with a shared EINT
interrupt.

Fixes: 16d7ff2642e7 ("ARM: dts: add dts files for exynos5260 SoC")
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: dts: pfla02: increase phy reset duration 2019-08-13T11:38:49+00:00 Marco Felsch m.felsch@pengutronix.de 2019-03-04T10:49:40+00:00 919f4897748208d3f111e022bf23ce89e6088599 commit 032f85c9360fb1a08385c584c2c4ed114b33c260 upstream. Increase the reset duration to ensure correct phy functionality. The reset duration is taken from barebox commit 52fdd510de ("ARM: dts: pfla02: use long enough reset for ethernet phy"): Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a small percentage of modules have 'transmission timeouts' errors like barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0 warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3 eth0: 1000Mbps full duplex link detected eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout Cc: Stefan Christ <s.christ@phytec.de> Cc: Christian Hemp <c.hemp@phytec.de> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support") Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 032f85c9360fb1a08385c584c2c4ed114b33c260 upstream.

Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):

  Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
  small percentage of modules have 'transmission timeouts' errors like

  barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
  warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
  eth0: 1000Mbps full duplex link detected
  eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout

Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: dts: kirkwood: Fix polarity of GPIO fan lines 2019-05-02T20:41:17+00:00 Linus Walleij linus.walleij@linaro.org 2019-01-07T23:08:18+00:00 2a04467f95fe5017be44769e677de1dfe0c0731f commit b5f034845e70916fd33e172fad5ad530a29c10ab upstream. These two lines are active high, not active low. The bug was found when we changed the kernel to respect the polarity defined in the device tree. Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan") Cc: Jamie Lentin <jm@lentin.co.uk> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Julien D'Ascenzio <jdascenzio@posteo.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Jamie Lentin <jm@lentin.co.uk> Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net> Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit b5f034845e70916fd33e172fad5ad530a29c10ab upstream.

These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.

Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: dts: exynos: Disable pull control for MAX8997 interrupts on Origen 2019-02-11T17:53:17+00:00 Marek Szyprowski m.szyprowski@samsung.com 2018-09-05T10:02:15+00:00 dc7b9c6c0e8ec587371e892bbca249dd095c7e3d commit f5e758b8358f6c27e8a351ddf0b441a64cdabb94 upstream. PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have external pull-up resistors, so disable any pull control for those lines in respective pin controller node. This fixes support for MAX8997 interrupts and enables operation of wakeup from MAX8997 RTC alarm. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> [bwh: Backported to 3.16: - Use literal 0 instead of EXYNOS_PIN_PULL_NONE - Adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f5e758b8358f6c27e8a351ddf0b441a64cdabb94 upstream.

PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[bwh: Backported to 3.16:
 - Use literal 0 instead of EXYNOS_PIN_PULL_NONE
 - Adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: tegra: Fix Tegra30 Cardhu PCA954x reset 2018-12-16T22:08:13+00:00 Jon Hunter jonathanh@nvidia.com 2018-07-03T08:59:47+00:00 0e3db9f650a6f6fdba17e6da378d0cbacb40d20b commit 6e1811900b6fe6f2b4665dba6bd6ed32c6b98575 upstream. On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546 I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the Tegra is not configured as a GPIO but as a special-function IO (SFIO) that is multiplexing the pin to an I2S controller. On exiting system suspend, I2C commands sent to the PCA9546 are failing because there is no ACK. Although it is not possible to see exactly what is happening to the reset during suspend, by ensuring it is configured as a GPIO and driven high, to de-assert the reset, the failures are no longer seen. Please note that this GPIO is also used to drive the reset signal going to the camera connector on the board. However, given that there is no camera support currently for Cardhu, this should not have any impact. Fixes: 40431d16ff11 ("ARM: tegra: enable PCA9546 on Cardhu") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 6e1811900b6fe6f2b4665dba6bd6ed32c6b98575 upstream.

On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.

Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.

Fixes: 40431d16ff11 ("ARM: tegra: enable PCA9546 on Cardhu")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: dts: da850: Fix interrups property for gpio 2018-11-20T18:05:30+00:00 Keerthy j-keerthy@ti.com 2018-06-05T10:07:51+00:00 81a019d61e3ecb0a63c46879b1788c42a1fa46eb commit 3eb1b955cd7ed1e621ace856710006c2a8a7f231 upstream. The intc #interrupt-cells is equal to 1. Currently gpio node has 2 cells per IRQ which is wrong. Remove the additional cell for each of the interrupts. Signed-off-by: Keerthy <j-keerthy@ti.com> Fixes: 2e38b946dc54 ("ARM: davinci: da850: add GPIO DT node") Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 3eb1b955cd7ed1e621ace856710006c2a8a7f231 upstream.

The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc54 ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: 8753/1: decompressor: add a missing parameter to the addruart macro 2018-10-21T07:46:14+00:00 Łukasz Stelmach l.stelmach@samsung.com 2018-04-03T08:04:57+00:00 daf3ce621e904d1eccc1b5bdd51590689055b522 commit e07e3c33b9c0b5751ade624f44325c9bf2487ea6 upstream. In commit 639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro") an additional temporary register was added to the addruart macro, but the decompressor code wasn't updated. Fixes: 639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro") Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit e07e3c33b9c0b5751ade624f44325c9bf2487ea6 upstream.

In commit 639da5ee374b ("ARM: add an extra temp register to the low
level debugging addruart macro") an additional temporary register was
added to the addruart macro, but the decompressor code wasn't updated.

Fixes: 639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
zboot: fix stack protector in compressed boot phase 2018-10-21T07:45:16+00:00 Huacai Chen chenhc@lemote.com 2018-04-05T23:18:18+00:00 4b998a0ba5085f532bdc9d57e5c2ac8910176cf6 commit 7bbaf27d9c83037b6e60a818e57bdbedf6bc15be upstream. Calling __stack_chk_guard_setup() in decompress_kernel() is too late that stack checking always fails for decompress_kernel() itself. So remove __stack_chk_guard_setup() and initialize __stack_chk_guard before we call decompress_kernel(). Original code comes from ARM but also used for MIPS and SH, so fix them together. If without this fix, compressed booting of these archs will fail because stack checking is enabled by default (>=4.16). Link: http://lkml.kernel.org/r/1522226933-29317-1-git-send-email-chenhc@lemote.com Fixes: 8779657d29c0 ("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG") Signed-off-by: Huacai Chen <chenhc@lemote.com> Acked-by: James Hogan <jhogan@kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Rich Felker <dalias@libc.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> [bwh: Backported to 3.16: Only ARM has this problem] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit 7bbaf27d9c83037b6e60a818e57bdbedf6bc15be upstream.

Calling __stack_chk_guard_setup() in decompress_kernel() is too late
that stack checking always fails for decompress_kernel() itself.  So
remove __stack_chk_guard_setup() and initialize __stack_chk_guard before
we call decompress_kernel().

Original code comes from ARM but also used for MIPS and SH, so fix them
together.  If without this fix, compressed booting of these archs will
fail because stack checking is enabled by default (>=4.16).

Link: http://lkml.kernel.org/r/1522226933-29317-1-git-send-email-chenhc@lemote.com
Fixes: 8779657d29c0 ("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: Only ARM has this problem]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ARM: dts: at91: at91sam9g25: fix mux-mask pinctrl property 2018-10-21T07:44:56+00:00 Nicolas Ferre nicolas.ferre@microchip.com 2018-03-13T15:20:05+00:00 5e949a74f0daa5fd7432f4483922ccdadd302a80 commit e8fd0adf105e132fd84545997bbef3d5edc2c9c1 upstream. There are only 19 PIOB pins having primary names PB0-PB18. Not all of them have a 'C' function. So the pinctrl property mask ends up being the same as the other SoC of the at91sam9x5 series. Reported-by: Marek Sieranski <marek.sieranski@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit e8fd0adf105e132fd84545997bbef3d5edc2c9c1 upstream.

There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.

Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
arm: spear13xx: Fix spics gpio controller's warning 2018-06-16T21:21:50+00:00 Viresh Kumar viresh.kumar@linaro.org 2018-01-11T05:58:53+00:00 ba250b5ebb299ceea52a1de0026d45bfd0c9e433 commit f8975cb1b8a36d0839b6365235778dd9df1d04ca upstream. This fixes the following warning by also sending the flags argument for gpio controllers: Property 'cs-gpios', cell 6 is not a phandle reference in /ahb/apb/spi@e0100000 Fixes: 8113ba917dfa ("ARM: SPEAr: DT: Update device nodes") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> 
commit f8975cb1b8a36d0839b6365235778dd9df1d04ca upstream.

This fixes the following warning by also sending the flags argument for
gpio controllers:

Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000

Fixes: 8113ba917dfa ("ARM: SPEAr: DT: Update device nodes")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>