linux.git/arch/arm64/boot, branch v5.12.5

arm64: dts: renesas: falcon: Move console config to CPU board DTS

2021-05-19T08:56:44+00:00

commit e86ff34cc44a49aeae2af74444560b17a0a96c78 upstream.

The serial console is located on the Falcon CPU board.  Hence move
serial console configuration from the main Falcon DTS file to the DTS
file that describes the CPU board.

Fixes: 63070d7c2270e8de ("arm64: dts: renesas: Add Renesas Falcon boards support")
Signed-off-by: Geert Uytterhoeven 
Reviewed-by: Wolfram Sang 
Tested-by: Wolfram Sang 
Reviewed-by: Niklas Söderlund 
Link: https://lore.kernel.org/r/20210316154705.2433528-2-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman

arm64: dts: uniphier: Change phy-mode to RGMII-ID to enable delay pins for RTL8211E

2021-05-14T08:53:03+00:00

[ Upstream commit dcabb06bf127b3e0d3fbc94a2b65dd56c2725851 ]

UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.

After the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.

Fixes: c73730ee4c9a ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin

arm64: dts: mediatek: fix reset GPIO level on pumpkin

2021-05-14T08:52:24+00:00

[ Upstream commit a7dceafed43a4a610d340da3703653cca2c50c1d ]

The tca6416 chip is active low. Fix the reset-gpios value.

Fixes: e2a8fa1e0faa ("arm64: dts: mediatek: fix tca6416 reset GPIOs in pumpkin")
Signed-off-by: Fabien Parent 
Link: https://lore.kernel.org/r/20210223221826.2063911-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger 
Signed-off-by: Sasha Levin

arm64: dts: qcom: sm8250: fix display nodes

2021-05-14T08:52:23+00:00

[ Upstream commit 888771a9d04ff7bf96e5ecad37969002c88a95d7 ]

Apply these fixes to the newly added sm8250 display ndoes
 - Remove "notused" interconnect (which apparently was blindly copied from
   my old patches)
 - Use dispcc node example from dt-bindings, removing clocks which aren't
   documented or used by the driver and fixing the region size.

Fixes: 7c1dffd471b1 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes")
Signed-off-by: Jonathan Marek 
[DB: compatibility changes split into separate patch]
Signed-off-by: Dmitry Baryshkov 
Link: https://lore.kernel.org/r/20210329120051.3401567-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson 
Signed-off-by: Sasha Levin

arm64: dts: mt8173: fix wrong power-domain phandle of pmic

2021-05-14T08:52:23+00:00

[ Upstream commit 4db2b9af3ee92e6c51c6a9a5dc2748e4bc1800f9 ]

Due to power domain controller is added, the power domain's
phanle is also changed from 'scpsys' to 'spm', but forget to
modify pmic node's

Fixes: 8b6562644df9 ("arm64: dts: mediatek: Add mt8173 power domain controller")
Signed-off-by: Chunfeng Yun 
Reviewed-by: Enric Balletbo i Serra 
Link: https://lore.kernel.org/r/1616048328-13579-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Matthias Brugger 
Signed-off-by: Sasha Levin

arm64: dts: mt8183: Add gce client reg for display subcomponents

2021-05-14T08:52:23+00:00

[ Upstream commit b7a8f50a1437164607f73831075c06120aa1f3b3 ]

Add mediatek,gce-client-reg for mmsys, ccorr, aal, gamma, dither.

Fixes: 91f9c963ce79 ("arm64: dts: mt8183: Add display nodes for MT8183")
Signed-off-by: Hsin-Yi Wang 
Tested-by: Enric Balletbo i Serra 
Link: https://lore.kernel.org/r/20210324070842.1037233-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger 
Signed-off-by: Sasha Levin

arm64: dts: renesas: r8a779a0: Fix PMU interrupt

2021-05-14T08:52:23+00:00

[ Upstream commit bbbf6db5a0b56199702bb225132831bced2eee41 ]

Should use PPI No.7 for the PMU. Otherwise, the perf command didn't
show any information.

Fixes: 834c310f5418 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Yoshihiro Shimoda 
Link: https://lore.kernel.org/r/20210325041949.925777-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Sasha Levin

arm64: dts: renesas: r8a77980: Fix vin4-7 endpoint binding

2021-05-14T08:52:20+00:00

[ Upstream commit c8aebc1346522d3569690867ce3996642ad52e01 ]

This fixes the bindings in media framework:
The CSI40 is endpoint number 2
The CSI41 is endpoint number 3

Signed-off-by: Vladimir Barinov 
Reviewed-by: Niklas Söderlund 
Signed-off-by: Niklas Söderlund 
Link: https://lore.kernel.org/r/20210312174735.2118212-1-niklas.soderlund+renesas@ragnatech.se
Fixes: 3182aa4e0bf4d0ee ("arm64: dts: renesas: r8a77980: add CSI2/VIN support")
Signed-off-by: Geert Uytterhoeven 
Signed-off-by: Sasha Levin

arm64: dts: broadcom: bcm4908: set Asus GT-AC5300 port 7 PHY mode

2021-05-14T08:52:20+00:00

[ Upstream commit 5ccb9f9cf05bbd729430c6d6d30d40c96a15c56a ]

Port 7 is connected to the external BCM53134S switch using RGMII.

Fixes: 527a3ac9bdf8 ("arm64: dts: broadcom: bcm4908: describe internal switch")
Signed-off-by: Rafał Miłecki 
Signed-off-by: Florian Fainelli 
Signed-off-by: Sasha Levin

arm64: dts: qcom: db845c: fix correct powerdown pin for WSA881x

2021-05-14T08:52:20+00:00

[ Upstream commit c561740e7cfefaf3003a256f3a0cd9f8a069137c ]

WSA881x powerdown pin is connected to GPIO1 not gpio2, so correct this.
This was working so far due to a shift bug in gpio driver, however
once that is fixed this will stop working, so fix this!

Fixes: 89a32a4e769cc ("arm64: dts: qcom: db845c: add analog audio support")
Signed-off-by: Srinivas Kandagatla 
Link: https://lore.kernel.org/r/20210309102025.28405-1-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson 
Signed-off-by: Sasha Levin