[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.

A closer look reveals other issues:
  - Some functionality is available on alternative pins, but the
    PINMUX_DATA() entries is using the wrong marks,
  - Several configurations are missing.

Fix this by:
  - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
    CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
    resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
    corresponding enum IDs,
  - Adding all missing enum IDs and marks,
  - Use the right (*_PJ2x) variants for alternative pins,
  - Adding all missing configurations to pinmux_data[],
  - Adding all missing function GPIO definitions to pinmux_func_gpios[].

See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
  [1] Table 1.4 List of Pins
  [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
      Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
      (32 Mailboxes × 1 Channel),
  [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
      One Channel (96 Mailboxes × 1 Channel),
  [4] Table 48.3 Multiplexed Pins (Port B),
  [5] Table 48.4 Multiplexed Pins (Port C),
  [6] Table 48.10 Multiplexed Pins (Port J),
  [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>

Commit bcf24e1daa94 ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.

sh-allmodconfig now fails with:

    include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
    make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1

This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h.  There's a similar issue with "CCR2"
on sh2a.

As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There are two ports that can output the LCD data, therefore
they have to use separate pimux identifiers so we can select
the one we want to use.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Commit 7025bec9125b0a02edcaf22c2dce753bf2c95480 ("sh: Kill off dead UBC
headers.") skipped arch/sh/include/cpu-sh2a/cpu/ubc.h. Since nothing is
using that header either, kill it off too.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This has turned in to quite a mess, and with CPUs that care using
dmaengine now it's about time to start cleaning up after the legacy DMA
code. For starters, kill off the stubs for the CPUs that don't do
anything, as well as all of the unused definitions. This leaves us with a
set of IRQs and base addresses we can deal with later.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

We use flush_cache_page() outright in copy_to_user_page(), and nothing
else needs it, so just kill it off. SH-5 still defines its own version,
but that too will go away in the same fashion once it converts over.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

All of the flush_dcache_mmap_lock()/flush_dcache_mmap_unlock()
definitions are identical across all CPUs, so just provide them
generically in asm/cacheflush.h.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>