linux.git/arch, branch v4.4.24

KVM: nVMX: postpone VMCS changes on MSR_IA32_APICBASE write

2016-10-07T13:23:46+00:00

commit dccbfcf52cebb8963246eba5b177b77f26b34da0 upstream.

If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the
write with vmcs02 as the current VMCS.
This will incorrectly apply modifications intended for vmcs01 to vmcs02
and L2 can use it to gain access to L0's x2APIC registers by disabling
virtualized x2APIC while using msr bitmap that assumes enabled.

Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the
current VMCS.  An alternative solution would temporarily make vmcs01 the
current VMCS, but it requires more care.

Fixes: 8d14695f9542 ("x86, apicv: add virtual x2apic support")
Reported-by: Jim Mattson 
Reviewed-by: Wanpeng Li 
Signed-off-by: Radim Krčmář 
Signed-off-by: Greg Kroah-Hartman

powerpc/prom: Fix sub-processor option passed to ibm, client-architecture-support

2016-10-07T13:23:46+00:00

commit 66443efa83dc73775100b7442962ce2cb0d4472e upstream.

When booting from an OpenFirmware which supports it, we use the
"ibm,client-architecture-support" firmware call to communicate
our capabilities to firmware.

The format of the structure we pass to firmware is specified in
PAPR (Power Architecture Platform Requirements), or the public version
LoPAPR (Linux on Power Architecture Platform Reference).

Referring to table 244 in LoPAPR v1.1, option vector 5 contains a 4 byte
field at bytes 17-20 for the "Platform Facilities Enable". This is
followed by a 1 byte field at byte 21 for "Sub-Processor Represenation
Level".

Comparing to the code, there we have the Platform Facilities
options (OV5_PFO_*) at byte 17, but we fail to pad that field out to its
full width of 4 bytes. This means the OV5_SUB_PROCESSORS option is
incorrectly placed at byte 18.

Fix it by adding zero bytes for bytes 18, 19, 20, and comment the bytes
to hopefully make it clearer in future.

As far as I'm aware nothing actually consumes this value at this time,
so the effect of this bug is nil in practice.

It does mean we've been incorrectly setting bit 15 of the "Platform
Facilities Enable" option for the past ~3 1/2 years, so we should avoid
allocating that bit to anything else in future.

Fixes: df77c7992029 ("powerpc/pseries: Update ibm,architecture.vec for PAPR 2.7/POWER8")
Signed-off-by: Michael Ellerman 
Signed-off-by: Benjamin Herrenschmidt 
Signed-off-by: Greg Kroah-Hartman

avr32: off by one in at32_init_pio()

2016-10-07T13:23:45+00:00

commit 55f1cf83d5cf885c75267269729805852039c834 upstream.

The pio_dev[] array has MAX_NR_PIO_DEVICES elements so the > should be
>=.

Fixes: 5f97f7f9400d ('[PATCH] avr32 architecture')
Signed-off-by: Dan Carpenter 
Signed-off-by: Greg Kroah-Hartman

tile: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO

2016-10-07T13:23:44+00:00

commit cdf8b4633075f2171d440d2e37c9c2609019a81a upstream.

AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for tile at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for
the VDSO address.

This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which tile doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.

Fixes: 4a556f4f56da ("tile: implement gettimeofday() via vDSO")
Signed-off-by: James Hogan 
Cc: Chris Metcalf 
Signed-off-by: Chris Metcalf 
Signed-off-by: Greg Kroah-Hartman

ARM: sa1111: fix pcmcia suspend/resume

2016-10-07T13:23:44+00:00

commit 06dfe5cc0cc684e735cb0232fdb756d30780b05d upstream.

SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for
the PCMCIA socket class.  PCMCIA used to handle suspend/resume via the
socket hosting device, which happened at normal device suspend/resume
time.

However, the referenced commit changed this: much of the resume now
happens much earlier, in the noirq resume handler of dev_pm_ops.

However, on SA1111, the PCMCIA device is not accessible as the SA1111
has not been resumed at _noirq time.  It's slightly worse than that,
because the SA1111 has already been put to sleep at _noirq time, so
suspend doesn't work properly.

Fix this by converting the core SA1111 code to use dev_pm_ops as well,
and performing its own suspend/resume at noirq time.

This fixes these errors in the kernel log:

pcmcia_socket pcmcia_socket0: time out after reset
pcmcia_socket pcmcia_socket1: time out after reset

and the resulting lack of PCMCIA cards after a S2RAM cycle.

Fixes: d7646f7632549 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class")
Signed-off-by: Russell King 
Signed-off-by: Greg Kroah-Hartman

ARM: shmobile: fix regulator quirk for Gen2

2016-10-07T13:23:43+00:00

commit c2f321126e31cd69365e65ecd4a7c774e4fc71d2 upstream.

The current implementation only works if the da9xxx devices are added
before their drivers are registered. Only then it can apply the fixes to
both devices. Otherwise, the driver for the first device gets probed
before the fix for the second device can be applied. This is what
fails when using the IP core switcher or when having the i2c master
driver as a module.

So, we need to disable both da9xxx once we detected one of them. We now
use i2c_transfer with hardcoded i2c_messages and device addresses, so we
don't need the da9xxx client devices to be instantiated. Because the
fixup is used on specific boards only, the addresses are not going to
change.

Fixes: 663fbb52159cca ("ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk")
Signed-off-by: Wolfram Sang 
Reviewed-by: Geert Uytterhoeven 
Tested-by: Geert Uytterhoeven  (r8a7791/koelsch)
Tested-by: Kuninori Morimoto 
Signed-off-by: Simon Horman 
Signed-off-by: Greg Kroah-Hartman

ARM: sa1100: clear reset status prior to reboot

2016-10-07T13:23:43+00:00

commit da60626e7d02a4f385cae80e450afc8b07035368 upstream.

Clear the current reset status prior to rebooting the platform.  This
adds the bit missing from 04fef228fb00 ("[ARM] pxa: introduce
reset_status and clear_reset_status for driver's usage").

Fixes: 04fef228fb00 ("[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage")
Signed-off-by: Russell King 
Signed-off-by: Greg Kroah-Hartman

ARM: sa1100: fix 3.6864MHz clock

2016-10-07T13:23:43+00:00

commit 02ba38a5b6d6e0bc89c7b74651f1873055028a56 upstream.

pxa_timer wants to be able to call clk_enable() etc on this clock,
but our clk_enable() implementation expects non-NULL enable/disable
operations.  Provide these dummy implementations.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 80000005 [#1] ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.8.0-rc2+ #887
Hardware name: Intel-Assabet
task: c0644590 task.stack: c0640000
PC is at 0x0
LR is at clk_enable+0x40/0x58
pc : [<00000000>]    lr : []    psr: 600000d3
sp : c0641f60  ip : c0641f4c  fp : c0641f74
r10: c1ffc7a0  r9 : 6901b118  r8 : 00000001
r7 : c0639a34  r6 : 0000001b  r5 : a00000d3  r4 : c0645d70
r3 : c0645d78  r2 : 00000001  r1 : c0641ef0  r0 : c0645d70
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32  ISA ARM  Segment none
Control: c020717f  Table: c020717f  DAC: 00000053
Process swapper (pid: 0, stack limit = 0xc0640188)
Stack: (0xc0641f60 to 0xc0642000)
1f60: 00384000 c08762e4 c0641f98 c0641f78 c063308c c021b144 00000000 00000000
1f80: 00000000 c0660b20 ffffffff c0641fa8 c0641f9c c06220ec c0633058 c0641fb8
1fa0: c0641fac c061f114 c06220dc c0641ff4 c0641fbc c061bb68 c061f0fc ffffffff
1fc0: ffffffff 00000000 c061b6cc c0639a34 c0660cd4 c0642038 c0639a30 c0645434
1fe0: c0204000 c06380f8 00000000 c0641ff8 c0208048 c061b954 00000000 00000000
Backtrace:
[] (clk_enable) from [] (pxa_timer_nodt_init+0x40/0x120)
 r5:c08762e4 r4:00384000
[] (pxa_timer_nodt_init) from [] (sa1100_timer_init+0x1c/0x20)
 r6:ffffffff r5:c0660b20 r4:00000000
[] (sa1100_timer_init) from [] (time_init+0x24/0x2c)
[] (time_init) from [] (start_kernel+0x220/0x42c)
[] (start_kernel) from [] (0xc0208048)
 r10:c06380f8 r8:c0204000 r7:c0645434 r6:c0639a30 r5:c0642038 r4:c0660cd4
Code: bad PC value
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Attempted to kill the idle task!

Fixes: ee3a4020f7c9 ("ARM: 8250/1: sa1100: provide OSTIMER0 clock for pxa_timer")
Acked-by: Dmitry Eremin-Solenikov 
Signed-off-by: Russell King 
Signed-off-by: Greg Kroah-Hartman

ARM: sa1100: register clocks early

2016-10-07T13:23:43+00:00

commit 198b51e8a6a31d3a6f8e9dd9cade3635d0291f26 upstream.

Since we switched to use pxa_timer, we need to provide the OSTIMER0
clock.  However, as the clock is initialised early, we need to provide
the clock early as well, so that pxa_timer can find it.  Adding the
clock to the clkdev table at core_initcall() time is way too late.

Move the initialisation earlier.

Fixes: ee3a4020f7c9 ("ARM: 8250/1: sa1100: provide OSTIMER0 clock for pxa_timer")
Acked-by: Dmitry Eremin-Solenikov 
Signed-off-by: Russell King 
Signed-off-by: Greg Kroah-Hartman

ARM: sun5i: Fix typo in trip point temperature

2016-10-07T13:23:43+00:00

commit 539d5c48a4aff5a4afcff117418618b49126c54c upstream.

Set cpu_alert0 temperature to 85°C instead of 850°C.

Fixes: 32a5d2d170cc ("ARM: dts: sun5i: Add cpu thermal zones to dtsi")
Signed-off-by: Hugo Grostabussiat 
Acked-by: Chen-Yu Tsai 
Signed-off-by: Maxime Ripard 
Signed-off-by: Greg Kroah-Hartman