Extend aquacomputer_d5next driver to expose hardware temperature sensors and fans of the Aquacomputer Quadro fan controller, which communicates through a proprietary USB HID protocol. Implemented by Jack Doan [1]. Four temperature sensors and PWM controllable fans are available. The liquid flow sensor is also exposed, implemented by Leonard Anderweit [2]. Additionally, serial number, firmware version and power-on count are exposed through debugfs. This driver has been tested on x86_64. [1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5 [2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9 Originally-from: Jack Doan <me@jackdoan.com> Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com> Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com> Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile just fine on ARCH=arm. Allow to select these drivers if COMPILE_TEST is enabled. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Jean Delvare <jdelvare@suse.de> Link: https://lore.kernel.org/r/20220527153445.1871086-1-u.kleine-koenig@pengutronix.de Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID registers as well as 11 bit external temperature resolution. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1020 is compatible with ADM1021 but has a separate chip revision and a limited I2C address range. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet error checking). Similar to NCT72 and NCT214, PEC support is undocumented. Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when reading those registers. The value for the chip revision register is not documented but was observed to be 0xca. Use that information to improve chip detection accuracy. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full PEC (packet error checking) support. PEC support is undocumented. Both chips support the undocumented secondary chip and manufacturer ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this information to improve the accuracy of chip detection code. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature offset register. A real chip was found to have a chip revision of 0x3f. Use it to detect NCT210 explicitly. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90 driver. Make that support official. After this change, the adm1021 driver is only needed if the lm90 driver is disabled. Also, the adm1021 driver misdetects a variety of chips as MAX1617A, which is unwanted if any of those chips is in the system. For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to show that it is not needed if the lm90 driver is enabled, and to avoid misdetection if a chip supported by the lm90 driver is in the system. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add support for them to the lm90 driver. Also mention ON Semiconductor NCT210, which is pin and register compatible to ADM1021A. None of the chips support the secondary manufacturer and chip ID registers at 0x3e and 0x3f, but return 0 when reading from those registers. Use that information to improve the accuracy of chip detection code. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily be supported by the LM90 driver. The most difficult part is chip detection, since those old chips do not support manufacturer ID or chip ID registers. The "alarms" attribute is enabled for both chips to match the functionality of the adm1021 driver. Chip detection was improved and is less prone to misdetection than the chip detection in the adm1021 driver. Devicetree nodes are not added for the added chips since it is quite unlikely that such old chips will ever be used in a devicetree based system. They can be added later if needed. Signed-off-by: Guenter Roeck <linux@roeck-us.net>