linux.git/drivers/i2c, branch v6.13.11 Clone of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git i2c: omap: fix IRQ storms 2025-03-28T21:04:54+00:00 Andreas Kemnade andreas@kemnade.info 2025-02-28T14:04:20+00:00 cd31436debe9f577983ad56f2340c189831a75ae commit 285df995f90e3d61d97f327d34b9659d92313314 upstream. On the GTA04A5 writing a reset command to the gyroscope causes IRQ storms because NACK IRQs are enabled and therefore triggered but not acked. Sending a reset command to the gyroscope by i2cset 1 0x69 0x14 0xb6 with an additional debug print in the ISR (not the thread) itself causes [ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00 [ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1 [ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110) [ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010) [ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102) [ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102) [ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102) repeating till infinity [...] (0x2 = NACK, 0x100 = Bus free, which is not enabled) Apparently no other IRQ bit gets set, so this stalls. Do not ignore enabled interrupts and make sure they are acked. If the NACK IRQ is not needed, it should simply not enabled, but according to the above log, caring about it is necessary unless the Bus free IRQ is enabled and handled. The assumption that is will always come with a ARDY IRQ, which was the idea behind ignoring it, proves wrong. It is true for simple reads from an unused address. To still avoid the i2cdetect trouble which is the reason for commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"), avoid doing much about NACK in omap_i2c_xfer_data() which is used by both IRQ mode and polling mode, so also the false detection fix is extended to polling usage and IRQ storms are avoided. By changing this, the hardirq handler is not needed anymore to filter stuff. The mentioned gyro reset now just causes a -ETIMEDOUT instead of hanging the system. Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"). CC: stable@kernel.org Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: Nishanth Menon <nm@ti.com> Reviewed-by: Aniket Limaye <a-limaye@ti.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 285df995f90e3d61d97f327d34b9659d92313314 upstream.

On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.

Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes

[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.

Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.

To still avoid the i2cdetect trouble which is the reason for
commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.

By changing this, the hardirq handler is not needed anymore to filter
stuff.

The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.

Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: sis630: Fix an error handling path in sis630_probe() 2025-03-22T19:56:58+00:00 Christophe JAILLET christophe.jaillet@wanadoo.fr 2025-03-03T20:26:54+00:00 d5e3ecbd3cb3fd65f86fda7832b59187231295ad [ Upstream commit 2b22459792fcb4def9f0936d64575ac11a95a58d ] If i2c_add_adapter() fails, the request_region() call in sis630_setup() must be undone by a corresponding release_region() call, as done in the remove function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 2b22459792fcb4def9f0936d64575ac11a95a58d ]

If i2c_add_adapter() fails, the request_region() call in sis630_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: ali15x3: Fix an error handling path in ali15x3_probe() 2025-03-22T19:56:58+00:00 Christophe JAILLET christophe.jaillet@wanadoo.fr 2025-03-03T19:58:06+00:00 f2ca4f009509d5d0a01754a7e48f69dc5c35b2db [ Upstream commit 6e55caaf30c88209d097e575a169b1dface1ab69 ] If i2c_add_adapter() fails, the request_region() call in ali15x3_setup() must be undone by a corresponding release_region() call, as done in the remove function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 6e55caaf30c88209d097e575a169b1dface1ab69 ]

If i2c_add_adapter() fails, the request_region() call in ali15x3_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: ali1535: Fix an error handling path in ali1535_probe() 2025-03-22T19:56:58+00:00 Christophe JAILLET christophe.jaillet@wanadoo.fr 2025-03-03T19:53:08+00:00 c55385168d5466d79f95b187c28ad0a3bbb7218e [ Upstream commit 9b5463f349d019a261f1e80803447efca3126151 ] If i2c_add_adapter() fails, the request_region() call in ali1535_setup() must be undone by a corresponding release_region() call, as done in the remove function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 9b5463f349d019a261f1e80803447efca3126151 ]

If i2c_add_adapter() fails, the request_region() call in ali1535_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: amd-asf: Fix EOI register write to enable successive interrupts 2025-03-07T17:27:09+00:00 Shyam Sundar S K Shyam-sundar.S-k@amd.com 2025-02-19T13:57:47+00:00 c21ff860700484163c038e173975b7b134661502 commit 9f3c507cb44498067c980674139bcad56e582ee6 upstream. The commit b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt") introduced a method to enable successive interrupts but inadvertently omitted the necessary write to the EOI register, resulting in a failure to receive successive interrupts. Fix this by adding the required write to the EOI register. Fixes: b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt") Cc: stable@vger.kernel.org # v6.13+ Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com> Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Fixes: 9b25419ad397 ("i2c: amd-asf: Add routine to handle the ASF slave process") Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20250219135747.3251182-1-Shyam-sundar.S-k@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 9f3c507cb44498067c980674139bcad56e582ee6 upstream.

The commit b1f8921dfbaa
("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
introduced a method to enable successive interrupts but inadvertently
omitted the necessary write to the EOI register, resulting in a failure to
receive successive interrupts.

Fix this by adding the required write to the EOI register.

Fixes: b1f8921dfbaa ("i2c: amd-asf: Clear remote IRR bit to get successive interrupt")
Cc: stable@vger.kernel.org # v6.13+
Co-developed-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Fixes: 9b25419ad397 ("i2c: amd-asf: Add routine to handle the ASF slave process")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250219135747.3251182-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: ls2x: Fix frequency division register access 2025-03-07T17:27:08+00:00 Binbin Zhou zhoubinbin@loongson.cn 2025-02-20T12:56:12+00:00 541cd4fb566bc945f8d84e0318e152b756cb6d66 commit 71c49ee9bb41e1709abac7e2eb05f9193222e580 upstream. According to the chip manual, the I2C register access type of Loongson-2K2000/LS7A is "B", so we can only access registers in byte form (readb()/writeb()). Although Loongson-2K0500/Loongson-2K1000 do not have similar constraints, register accesses in byte form also behave correctly. Also, in hardware, the frequency division registers are defined as two separate registers (high 8-bit and low 8-bit), so we just access them directly as bytes. Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller") Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn> Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn> Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn> Cc: stable@vger.kernel.org # v6.3+ Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit 71c49ee9bb41e1709abac7e2eb05f9193222e580 upstream.

According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).

Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.

Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.

Fixes: 015e61f0bffd ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: npcm: disable interrupt enable bit before devm_request_irq 2025-03-07T17:27:08+00:00 Tyrone Ting kfting@nuvoton.com 2025-02-20T04:00:29+00:00 846e371631c57365eeb89e5db1ab0f344169af93 commit dd1998e243f5fa25d348a384ba0b6c84d980f2b2 upstream. The customer reports that there is a soft lockup issue related to the i2c driver. After checking, the i2c module was doing a tx transfer and the bmc machine reboots in the middle of the i2c transaction, the i2c module keeps the status without being reset. Due to such an i2c module status, the i2c irq handler keeps getting triggered since the i2c irq handler is registered in the kernel booting process after the bmc machine is doing a warm rebooting. The continuous triggering is stopped by the soft lockup watchdog timer. Disable the interrupt enable bit in the i2c module before calling devm_request_irq to fix this issue since the i2c relative status bit is read-only. Here is the soft lockup log. [ 28.176395] watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [swapper/0:1] [ 28.183351] Modules linked in: [ 28.186407] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.120-yocto-s-dirty-bbebc78 #1 [ 28.201174] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 28.208128] pc : __do_softirq+0xb0/0x368 [ 28.212055] lr : __do_softirq+0x70/0x368 [ 28.215972] sp : ffffff8035ebca00 [ 28.219278] x29: ffffff8035ebca00 x28: 0000000000000002 x27: ffffff80071a3780 [ 28.226412] x26: ffffffc008bdc000 x25: ffffffc008bcc640 x24: ffffffc008be50c0 [ 28.233546] x23: ffffffc00800200c x22: 0000000000000000 x21: 000000000000001b [ 28.240679] x20: 0000000000000000 x19: ffffff80001c3200 x18: ffffffffffffffff [ 28.247812] x17: ffffffc02d2e0000 x16: ffffff8035eb8b40 x15: 00001e8480000000 [ 28.254945] x14: 02c3647e37dbfcb6 x13: 02c364f2ab14200c x12: 0000000002c364f2 [ 28.262078] x11: 00000000fa83b2da x10: 000000000000b67e x9 : ffffffc008010250 [ 28.269211] x8 : 000000009d983d00 x7 : 7fffffffffffffff x6 : 0000036d74732434 [ 28.276344] x5 : 00ffffffffffffff x4 : 0000000000000015 x3 : 0000000000000198 [ 28.283476] x2 : ffffffc02d2e0000 x1 : 00000000000000e0 x0 : ffffffc008bdcb40 [ 28.290611] Call trace: [ 28.293052] __do_softirq+0xb0/0x368 [ 28.296625] __irq_exit_rcu+0xe0/0x100 [ 28.300374] irq_exit+0x14/0x20 [ 28.303513] handle_domain_irq+0x68/0x90 [ 28.307440] gic_handle_irq+0x78/0xb0 [ 28.311098] call_on_irq_stack+0x20/0x38 [ 28.315019] do_interrupt_handler+0x54/0x5c [ 28.319199] el1_interrupt+0x2c/0x4c [ 28.322777] el1h_64_irq_handler+0x14/0x20 [ 28.326872] el1h_64_irq+0x74/0x78 [ 28.330269] __setup_irq+0x454/0x780 [ 28.333841] request_threaded_irq+0xd0/0x1b4 [ 28.338107] devm_request_threaded_irq+0x84/0x100 [ 28.342809] npcm_i2c_probe_bus+0x188/0x3d0 [ 28.346990] platform_probe+0x6c/0xc4 [ 28.350653] really_probe+0xcc/0x45c [ 28.354227] __driver_probe_device+0x8c/0x160 [ 28.358578] driver_probe_device+0x44/0xe0 [ 28.362670] __driver_attach+0x124/0x1d0 [ 28.366589] bus_for_each_dev+0x7c/0xe0 [ 28.370426] driver_attach+0x28/0x30 [ 28.373997] bus_add_driver+0x124/0x240 [ 28.377830] driver_register+0x7c/0x124 [ 28.381662] __platform_driver_register+0x2c/0x34 [ 28.386362] npcm_i2c_init+0x3c/0x5c [ 28.389937] do_one_initcall+0x74/0x230 [ 28.393768] kernel_init_freeable+0x24c/0x2b4 [ 28.398126] kernel_init+0x28/0x130 [ 28.401614] ret_from_fork+0x10/0x20 [ 28.405189] Kernel panic - not syncing: softlockup: hung tasks [ 28.411011] SMP: stopping secondary CPUs [ 28.414933] Kernel Offset: disabled [ 28.418412] CPU features: 0x00000000,00000802 [ 28.427644] Rebooting in 20 seconds.. Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Cc: <stable@vger.kernel.org> # v5.8+ Reviewed-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20250220040029.27596-2-kfting@nuvoton.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
commit dd1998e243f5fa25d348a384ba0b6c84d980f2b2 upstream.

The customer reports that there is a soft lockup issue related to
the i2c driver. After checking, the i2c module was doing a tx transfer
and the bmc machine reboots in the middle of the i2c transaction, the i2c
module keeps the status without being reset.

Due to such an i2c module status, the i2c irq handler keeps getting
triggered since the i2c irq handler is registered in the kernel booting
process after the bmc machine is doing a warm rebooting.
The continuous triggering is stopped by the soft lockup watchdog timer.

Disable the interrupt enable bit in the i2c module before calling
devm_request_irq to fix this issue since the i2c relative status bit
is read-only.

Here is the soft lockup log.
[   28.176395] watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [swapper/0:1]
[   28.183351] Modules linked in:
[   28.186407] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.120-yocto-s-dirty-bbebc78 #1
[   28.201174] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   28.208128] pc : __do_softirq+0xb0/0x368
[   28.212055] lr : __do_softirq+0x70/0x368
[   28.215972] sp : ffffff8035ebca00
[   28.219278] x29: ffffff8035ebca00 x28: 0000000000000002 x27: ffffff80071a3780
[   28.226412] x26: ffffffc008bdc000 x25: ffffffc008bcc640 x24: ffffffc008be50c0
[   28.233546] x23: ffffffc00800200c x22: 0000000000000000 x21: 000000000000001b
[   28.240679] x20: 0000000000000000 x19: ffffff80001c3200 x18: ffffffffffffffff
[   28.247812] x17: ffffffc02d2e0000 x16: ffffff8035eb8b40 x15: 00001e8480000000
[   28.254945] x14: 02c3647e37dbfcb6 x13: 02c364f2ab14200c x12: 0000000002c364f2
[   28.262078] x11: 00000000fa83b2da x10: 000000000000b67e x9 : ffffffc008010250
[   28.269211] x8 : 000000009d983d00 x7 : 7fffffffffffffff x6 : 0000036d74732434
[   28.276344] x5 : 00ffffffffffffff x4 : 0000000000000015 x3 : 0000000000000198
[   28.283476] x2 : ffffffc02d2e0000 x1 : 00000000000000e0 x0 : ffffffc008bdcb40
[   28.290611] Call trace:
[   28.293052]  __do_softirq+0xb0/0x368
[   28.296625]  __irq_exit_rcu+0xe0/0x100
[   28.300374]  irq_exit+0x14/0x20
[   28.303513]  handle_domain_irq+0x68/0x90
[   28.307440]  gic_handle_irq+0x78/0xb0
[   28.311098]  call_on_irq_stack+0x20/0x38
[   28.315019]  do_interrupt_handler+0x54/0x5c
[   28.319199]  el1_interrupt+0x2c/0x4c
[   28.322777]  el1h_64_irq_handler+0x14/0x20
[   28.326872]  el1h_64_irq+0x74/0x78
[   28.330269]  __setup_irq+0x454/0x780
[   28.333841]  request_threaded_irq+0xd0/0x1b4
[   28.338107]  devm_request_threaded_irq+0x84/0x100
[   28.342809]  npcm_i2c_probe_bus+0x188/0x3d0
[   28.346990]  platform_probe+0x6c/0xc4
[   28.350653]  really_probe+0xcc/0x45c
[   28.354227]  __driver_probe_device+0x8c/0x160
[   28.358578]  driver_probe_device+0x44/0xe0
[   28.362670]  __driver_attach+0x124/0x1d0
[   28.366589]  bus_for_each_dev+0x7c/0xe0
[   28.370426]  driver_attach+0x28/0x30
[   28.373997]  bus_add_driver+0x124/0x240
[   28.377830]  driver_register+0x7c/0x124
[   28.381662]  __platform_driver_register+0x2c/0x34
[   28.386362]  npcm_i2c_init+0x3c/0x5c
[   28.389937]  do_one_initcall+0x74/0x230
[   28.393768]  kernel_init_freeable+0x24c/0x2b4
[   28.398126]  kernel_init+0x28/0x130
[   28.401614]  ret_from_fork+0x10/0x20
[   28.405189] Kernel panic - not syncing: softlockup: hung tasks
[   28.411011] SMP: stopping secondary CPUs
[   28.414933] Kernel Offset: disabled
[   28.418412] CPU features: 0x00000000,00000802
[   28.427644] Rebooting in 20 seconds..

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220040029.27596-2-kfting@nuvoton.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz 2025-02-17T10:36:03+00:00 Randolph Ha rha051117@gmail.com 2025-01-13T19:52:37+00:00 66da90f01b957e9e4fdb285dbcd59e970ad89436 [ Upstream commit bfd74cd1fbc026f04446e67d6915c7e199c2bffd ] When a 400KHz freq is used on this model of ELAN touchpad in Linux, excessive smoothing (similar to when the touchpad's firmware detects a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo V15 G4) ACPI tables specify a 400KHz frequency for this device and some I2C busses (e.g, Designware I2C) default to a 400KHz freq, force the speed to 100KHz as a workaround. For future investigation: This problem may be related to the default HCNT/LCNT values given by some busses' drivers, because they are not specified in the aforementioned devices' ACPI tables, and because the device works without issues on Windows at what is expected to be a 400KHz frequency. The root cause of the issue is not known. Signed-off-by: Randolph Ha <rha051117@gmail.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit bfd74cd1fbc026f04446e67d6915c7e199c2bffd ]

When a 400KHz freq is used on this model of ELAN touchpad in Linux,
excessive smoothing (similar to when the touchpad's firmware detects
a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo
V15 G4) ACPI tables specify a 400KHz frequency for this device and
some I2C busses (e.g, Designware I2C) default to a 400KHz freq,
force the speed to 100KHz as a workaround.

For future investigation: This problem may be related to the default
HCNT/LCNT values given by some busses' drivers, because they are not
specified in the aforementioned devices' ACPI tables, and because
the device works without issues on Windows at what is expected to be
a 400KHz frequency. The root cause of the issue is not known.

Signed-off-by: Randolph Ha <rha051117@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: designware: Actually make use of the I2C_DW_COMMON and I2C_DW symbol namespaces 2025-02-08T09:01:25+00:00 Uwe Kleine-König u.kleine-koenig@baylibre.com 2024-12-30T15:59:49+00:00 e53d64b5e156f564d6ac4f26fdf86524c8813337 [ Upstream commit f0a4e9fa656ceb3b2e4c296cf6226798d804fa22 ] DEFAULT_SYMBOL_NAMESPACE must already be defined when <linux/export.h> is included. So move the define above the include block. Fixes: fd57a3325a77 ("i2c: designware: Move exports to I2C_DW namespaces") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f0a4e9fa656ceb3b2e4c296cf6226798d804fa22 ]

DEFAULT_SYMBOL_NAMESPACE must already be defined when <linux/export.h>
is included. So move the define above the include block.

Fixes: fd57a3325a77 ("i2c: designware: Move exports to I2C_DW namespaces")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
i2c: testunit: on errors, repeat NACK until STOP 2025-01-15T18:44:21+00:00 Wolfram Sang wsa+renesas@sang-engineering.com 2025-01-15T16:23:47+00:00 6ad30f7890423341f4b79329af1f9b9bb3cdec03 This backend requests a NACK from the controller driver when it detects an error. If that request gets ignored from some reason, subsequent accesses will wrongly be handled OK. To fix this, an error now changes the state machine, so the backend will report NACK until a STOP condition has been detected. This make the driver more robust against controllers which will sadly apply the NACK not to the current byte but the next one. Fixes: a8335c64c5f0 ("i2c: add slave testunit driver") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> 
This backend requests a NACK from the controller driver when it detects
an error. If that request gets ignored from some reason, subsequent
accesses will wrongly be handled OK. To fix this, an error now changes
the state machine, so the backend will report NACK until a STOP
condition has been detected. This make the driver more robust against
controllers which will sadly apply the NACK not to the current byte but
the next one.

Fixes: a8335c64c5f0 ("i2c: add slave testunit driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>