linux.git/drivers/iio/common, branch v4.9.209

iio: common: ssp_sensors: Initialize calculated_time in ssp_common_process_data

2019-05-31T13:48:27+00:00

[ Upstream commit 6f9ca1d3eb74b81f811a87002de2d51640d135b1 ]

When building with -Wsometimes-uninitialized, Clang warns:

drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable
'calculated_time' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]

While it isn't wrong, this will never be a problem because
iio_push_to_buffers_with_timestamp only uses calculated_time
on the same condition that it is assigned (when scan_timestamp
is not zero). While iio_push_to_buffers_with_timestamp is marked
as inline, Clang does inlining in the optimization stage, which
happens after the semantic analysis phase (plus inline is merely
a hint to the compiler).

Fix this by just zero initializing calculated_time.

Link: https://github.com/ClangBuiltLinux/linux/issues/394
Signed-off-by: Nathan Chancellor 
Reviewed-by: Nick Desaulniers 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Sasha Levin

iio: hid-sensor: fix return of -EINVAL on invalid values in ret or value

2018-03-24T10:00:16+00:00

[ Upstream commit c894acc7bf400d039bf740420b22f0b71b7fb504 ]

Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.

Fixes: 5d9854eaea776 ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: Colin Ian King 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

iio: hid-sensor-trigger: Fix the race with user space powering up sensors

2017-08-30T08:21:53+00:00

commit f1664eaacec31035450132c46ed2915fd2b2049a upstream.

It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.

The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
  auto-suspend for 3 seconds.
	This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
  active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks

If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.

To avoid this:
- Remove the check to match user requested state, this will cause a
  brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
  of sensors, like after user finished raw read or buffer disable

Signed-off-by: Srinivas Pandruvada 
Tested-by: Bastien Nocera 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: hid-sensor: Store restore poll and hysteresis on S3

2017-05-25T13:44:41+00:00

commit 5d9854eaea776441b38a9a45b4e6879524c4f48c upstream.

This change undo the change done by 'commit 3bec24747446
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.

Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.

In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.

Fixes: 3bec24747446 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf 
Tested-by: Ritesh Raj Sarraf 
Tested-by: Song, Hongyan 
Signed-off-by: Srinivas Pandruvada 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3

2017-03-30T07:41:25+00:00

commit 3bec247474469f769af41e8c80d3a100dd97dd76 upstream.

In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.

Signed-off-by: Song Hongyan 
Acked-by: Srinivas Pandruvada 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: accel: st_accel: fix LIS3LV02 reading and scaling

2017-01-12T10:39:21+00:00

commit 65e4345c8ef8811bbb4860fe5f2df10646b7f2e1 upstream.

The LIS3LV02 has a special bit that need to be set to get the
read values left aligned. Before this patch we get gibberish
like this:

iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.010042 -0.642688 19155832931907
0.000000 -0.010042 -0.642688 19155858751073

Which is because we read a raw value for 1g as 64 which is
the nominal 1024 for 1g shifted 4 bits to the left by being
right-aligned rather than left aligned.

Since all other sensors are left aligned, add some code to
set the special DAS (data alignment setting) bit to 1 so that
the right value is now read like this:

iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.147095 -10.120135 24761614364956
-0.029419 -0.176514 -10.120135 24761631624540

The scaling was weird as well: we have a gain of 1000 for 1g
and 3000 for 6g. I don't even remember how I came up with the
old values but they are wrong.

Fixes: 3acddf74f807 ("iio: st-sensors: add support for lis3lv02d accelerometer")
Cc: Lorenzo Bianconi 
Cc: Giuseppe Barba 
Cc: Denis Ciocca 
Signed-off-by: Linus Walleij 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: common: st_sensors: fix channel data parsing

2017-01-12T10:39:04+00:00

commit 65c8aea07de11b6507efa175edb44bd8b4488218 upstream.

Using realbits as i2c/spi read len, when that value is not byte aligned
(e.g 12 bits), lead to skip msb part of out data registers.
Fix this taking into account scan_type.shift in addition to
scan_type.realbits as read length:

read_len = DIV_ROUND_UP(realbits + shift, 8)

This fix has been tested on 8, 12, 16, 24 bit sensors

Fixes: e7385de5291e ("iio:st_sensors: align on storagebits boundaries")
Signed-off-by: Lorenzo Bianconi 
Tested-by: Linus Walleij 
Signed-off-by: Jonathan Cameron 
Signed-off-by: Greg Kroah-Hartman

iio: hid-sensors: Increase the precision of scale to fix wrong reading interpretation.

2016-11-05T17:50:56+00:00

While testing, it was observed that on some platforms the scale value
from iio sysfs for gyroscope is always 0 (E.g. Yoga 260). This results
in the final angular velocity component values to be zeros.

This is caused by insufficient precision of scale value displayed in sysfs.
If the precision is changed to nano from current micro, then this is
sufficient to display the scale value on this platform.
Since this can be a problem for all other HID sensors, increase scale
precision of all HID sensors to nano from current micro.

Results on Yoga 260:

name		scale before	scale now
--------------------------------------------
gyro_3d		0.000000	0.000000174
als			0.001000	0.001000000
magn_3d		0.000001	0.000001000
accel_3d		0.000009	0.000009806

Signed-off-by: Song Hongyan 
Acked-by: Srinivas Pandruvada 
Cc: 
Signed-off-by: Jonathan Cameron

iio: st_sensors: fix scale configuration for h3lis331dl

2016-10-30T16:46:46+00:00

fix scale configuration/parsing for h3lis331dl accel driver
when sensitivity is higher than 1(m/s^2)/digit

Signed-off-by: Lorenzo Bianconi 
Fixes: 1e52fefc9b0c ("iio: accel: Add support for the h3lis331dl accelerometer")
Cc: 
Signed-off-by: Jonathan Cameron

Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

2016-09-14T18:42:03+00:00

Jonathan writes:

Second set of iio new device support, features and cleanups for the 4.9 cycle.

New device support
* ad8801 dac
  - new driver supporting ad8801 and ad8803 DACs.
* adc12138
  - new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
  - new driver
* mxc6255
  - add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
  - add support for the vz89te part which drops the voc_short channel and adds
    CRCs compared to other supported parts.

New features
* core
  - immutable triggers.  These effectively grant exclusive control over a
    trigger. The typical usecase is a device representing an analog part
    (perhaps a MUX) that needs to control the sampling of a downstream
    ADC.
  - resource managed trigger registration and triggered_buffer_init.
  - iio_push_event now protected against case of the event interface
    registration not having yet occured.  Only matters if an interrupt
    can occur during this window - might happen on shared interrupt lines.
  - helper to let a driver query if the trigger it is using is provided by
    itself (using the convention of both device and trigger having the same
    parent).
* tools
  - iio-utils. Used channel modifier scaling in preference to generic scaling
    when both exist.
* at91-adc
  - Add support for touchscreen switches closure time needed by some newer
    parts.
* stx104
  - support the ADC channels on this ADC/DAC board. As these are the primary
    feature of the board also move the driver to the iio/adc directory.
* sx9500
  - device tree bindings.

Cleanups / Fixes
* ad5755
  - fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
  - drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
  - avoid an unused functional warning due to rework in PM core code.
  - remove .owner field setting as done by i2c_core.
* ina2xx
  - clear out a left over debug field from chip global data.
* hid-sensors
  - avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
  - fix non static symbol warnings.
* ms5611
  - fetch and enable regulators unconditionally when they aren't optional.
* sca3000
  - whitespace cleanup.
* st_sensors
  - fetch and enable regulators unconditionally rather than having them
    supported as optional regulators (missunderstanding on my part amongst
    others a while back)
  - followup to previous patch fixes error checking on the regulators.
  - mark symbols static where possible.
  - use the 'is it my trigger' help function.  This prevents the odd case
    of another device triggering from the st-sensors trigger whilst the
    st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
  - add missing of_node_put.
* vz89x
  - rework to all support of new devices.
  - prevent reading of a corrupted buffer.
  - fixup a return value of 0/1 in a bool returning function.

Address updates
- Vlad Dogaru email address change.