[ Upstream commit 94803aef3533676194c772383472636c453e3147 ] This patch fixes order of disable calls in pwm_vibrator_stop. Currently when starting device, we first enable vcc regulator and then setup and enable pwm. When stopping, we should do this in oposite order, so first disable pwm and then disable regulator. Previously order was the same as in start. Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca232df9921f083c3b37ba5fbc76f4d9046268b ] pwm_vibrator_stop disables the regulator, but it can be called from multiple places, even when the regulator is already disabled. Fix this by using regulator_is_enabled check when starting and stopping device. Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90cc55f067f6ca0e64e5e52883ece47d8af7b67b upstream. Otherwise we introduce a race condition where userspace can request input before we're ready leading to null pointer dereference such as input: bma150 as /devices/platform/i2c-gpio-2/i2c-5/5-0038/input/input3 Unable to handle kernel NULL pointer dereference at virtual address 00000018 pgd = (ptrval) [00000018] *pgd=55dac831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: bma150 input_polldev [last unloaded: bma150] CPU: 0 PID: 2870 Comm: accelerometer Not tainted 5.0.0-rc3-dirty #46 Hardware name: Samsung S5PC110/S5PV210-based board PC is at input_event+0x8/0x60 LR is at bma150_report_xyz+0x9c/0xe0 [bma150] pc : [<80450f70>] lr : [<7f0a614c>] psr: 800d0013 sp : a4c1fd78 ip : 00000081 fp : 00020000 r10: 00000000 r9 : a5e2944c r8 : a7455000 r7 : 00000016 r6 : 00000101 r5 : a7617940 r4 : 80909048 r3 : fffffff2 r2 : 00000000 r1 : 00000003 r0 : 00000000 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 54e34019 DAC: 00000051 Process accelerometer (pid: 2870, stack limit = 0x(ptrval)) Stackck: (0xa4c1fd78 to 0xa4c20000) fd60: fffffff3 fc813f6c fd80: 40410581 d7530ce3 a5e2817c a7617f00 a5e29404 a5e2817c 00000000 7f008324 fda0: a5e28000 8044f59c a5fdd9d0 a5e2945c a46a4a00 a5e29668 a7455000 80454f10 fdc0: 80909048 a5e29668 a5fdd9d0 a46a4a00 806316d0 00000000 a46a4a00 801df5f0 fde0: 00000000 d7530ce3 a4c1fec0 a46a4a00 00000000 a5fdd9d0 a46a4a08 801df53c fe00: 00000000 801d74bc a4c1fec0 00000000 a4c1ff70 00000000 a7038da8 00000000 fe20: a46a4a00 801e91fc a411bbe0 801f2e88 00000004 00000000 80909048 00000041 fe40: 00000000 00020000 00000000 dead4ead a6a88da0 00000000 ffffe000 806fcae8 fe60: a4c1fec8 00000000 80909048 00000002 a5fdd9d0 a7660110 a411bab0 00000001 fe80: dead4ead ffffffff ffffffff a4c1fe8c a4c1fe8c d7530ce3 20000013 80909048 fea0: 80909048 a4c1ff70 00000001 fffff000 a4c1e000 00000005 00026038 801eabd8 fec0: a7660110 a411bab0 b9394901 00000006 a696201b 76fb3000 00000000 a7039720 fee0: a5fdd9d0 00000101 00000002 00000096 00000000 00000000 00000000 a4c1ff00 ff00: a6b310f4 805cb174 a6b310f4 00000010 00000fe0 00000010 a4c1e000 d7530ce3 ff20: 00000003 a5f41400 a5f41424 00000000 a6962000 00000000 00000003 00000002 ff40: ffffff9c 000a0000 80909048 d7530ce3 a6962000 00000003 80909048 ffffff9c ff60: a6962000 801d890c 00000000 00000000 00020000 a7590000 00000004 00000100 ff80: 00000001 d7530ce3 000288b8 00026320 000288b8 00000005 80101204 a4c1e000 ffa0: 00000005 80101000 000288b8 00026320 000288b8 000a0000 00000000 00000000 ffc0: 000288b8 00026320 000288b8 00000005 7eef3bac 000264e8 00028ad8 00026038 ffe0: 00000005 7eef3300 76f76e91 76f78546 800d0030 000288b8 00000000 00000000 [<80450f70>] (input_event) from [<a5e2817c>] (0xa5e2817c) Code: e1a08148 eaffffa8 e351001f 812fff1e (e590c018) ---[ end trace 1c691ee85f2ff243 ]--- Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d77651a227f8920dd7ec179b84e400cce844eeb3 upstream. An integer overflow may arise in uinput_validate_absinfo() if "max - min" can't be represented by an "int". We should check for overflow before trying to use the result. Reported-by: Kyungtae Kim <kt0755@gmail.com> Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce6f7d087e2b037f47349c1c36ac97678d02e394 ]
kbdif protocol describes multi-touch device parameters as a
part of frontend's XenBus configuration nodes while they
belong to backend's configuration. Fix this by reading the
parameters as defined by the protocol.
Fixes: 49aac8204da5 ("Input: xen-kbdfront - add multi-touch support")
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02a0d9216d4daf6a58d88642bd2da2c78c327552 ] Some user-space applications expect multi-touch pressure on contact to be reported if it is advertised in device properties. Otherwise, such applications may treat reports not as actual touches, but hovering. Currently this is only advertised, but not reported. Fix this by not advertising that ABS_MT_PRESSURE is supported. Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com> Patchwork-Id: 10140017 Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b189201993ab03001a398de731045bfea90c689 upstream.
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while searching the whole device tree depth-first starting at the parent
node.
Fixes: 64b9e4d803b1 ("input: twl4030-vibra: Support for DT booted kernel")
Fixes: e661d0a04462 ("Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcaf12a8b0bbdbfcfa2be8dff2c4948d9844b4ad upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Later sanity checks on node properties (which would likely be missing)
should prevent this from causing much trouble however, especially as the
original premature free of the parent node has already been fixed
separately (but that "fix" was apparently never backported to stable).
Fixes: e7ec014a47e4 ("Input: twl6040-vibra - update for device tree support")
Fixes: c52c545ead97 ("Input: twl6040-vibra - fix DT node memory management")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> (on Pyra OMAP5 hardware)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input fixes from Dmitry Torokhov: - joydev now implements a blacklist to avoid creating joystick nodes for accelerometers found in composite devices such as PlaStation controllers - assorted driver fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: ims-psu - check if CDC union descriptor is sane Input: joydev - blacklist ds3/ds4/udraw motion sensors Input: allow matching device IDs on property bits Input: factor out and export input_device_id matching code Input: goodix - poll the 'buffer status' bit before reading data Input: axp20x-pek - fix module not auto-loading for axp221 pek Input: tca8418 - enable interrupt after it has been requested Input: stmfts - fix setting ABS_MT_POSITION_* maximum size Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen Input: synaptics - disable kernel tracking on SMBus devices