After commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM"), when the
rtsx controller is runtime suspended, bring CPUs offline and back online, the
runtime resume of the controller will fail:

[   47.319391] smpboot: CPU 1 is now offline
[   47.414140] x86: Booting SMP configuration:
[   47.414147] smpboot: Booting Node 0 Processor 1 APIC 0x2
[   47.571334] smpboot: CPU 2 is now offline
[   47.686055] smpboot: Booting Node 0 Processor 2 APIC 0x4
[   47.808174] smpboot: CPU 3 is now offline
[   47.878146] smpboot: Booting Node 0 Processor 3 APIC 0x6
[   48.003679] smpboot: CPU 4 is now offline
[   48.086187] smpboot: Booting Node 0 Processor 4 APIC 0x1
[   48.239627] smpboot: CPU 5 is now offline
[   48.326059] smpboot: Booting Node 0 Processor 5 APIC 0x3
[   48.472193] smpboot: CPU 6 is now offline
[   48.574181] smpboot: Booting Node 0 Processor 6 APIC 0x5
[   48.743375] smpboot: CPU 7 is now offline
[   48.838047] smpboot: Booting Node 0 Processor 7 APIC 0x7
[   48.965447] __common_interrupt: 1.35 No irq handler for vector
[   51.174065] mmc0: error -110 doing runtime resume
[   54.978088] I/O error, dev mmcblk0, sector 21479 op 0x1:(WRITE) flags 0x0 phys_seg 11 prio class 0
[   54.978108] Buffer I/O error on dev mmcblk0p1, logical block 19431, lost async page write
[   54.978129] Buffer I/O error on dev mmcblk0p1, logical block 19432, lost async page write
[   54.978134] Buffer I/O error on dev mmcblk0p1, logical block 19433, lost async page write
[   54.978137] Buffer I/O error on dev mmcblk0p1, logical block 19434, lost async page write
[   54.978141] Buffer I/O error on dev mmcblk0p1, logical block 19435, lost async page write
[   54.978145] Buffer I/O error on dev mmcblk0p1, logical block 19436, lost async page write
[   54.978148] Buffer I/O error on dev mmcblk0p1, logical block 19437, lost async page write
[   54.978152] Buffer I/O error on dev mmcblk0p1, logical block 19438, lost async page write
[   54.978155] Buffer I/O error on dev mmcblk0p1, logical block 19439, lost async page write
[   54.978160] Buffer I/O error on dev mmcblk0p1, logical block 19440, lost async page write
[   54.978244] mmc0: card aaaa removed
[   54.978452] FAT-fs (mmcblk0p1): FAT read failed (blocknr 4257)

There's interrupt immediately raised on rtsx_pci_write_register() in
runtime resume routine, but the IRQ handler hasn't registered yet.

So we can either move rtsx_pci_write_register() after rtsx_pci_acquire_irq(),
or just stop mangling IRQ on runtime PM. Choose the latter to save some
CPU cycles.

Fixes: 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1951784
Link: https://lore.kernel.org/r/20211126003246.1068770-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit fd307a4ad332 ("nvmem: prepare basics for FRAM support") added
support for FRAM devices such as the Cypress FM25V. During testing, it
was found that the FRAM detects properly, however reads and writes fail.
Upon further investigation, two problem were found in at25_probe() routine.

1) In the case of an FRAM device without platform data, eg.
       fram == true && spi->dev.platform_data == NULL
the stack local variable "struct spi_eeprom chip" is not initialized
fully, prior to being copied into at25->chip. The chip.flags field in
particular can cause problems.

2) The byte_len of FRAM is computed from its ID register, and is stored
into the stack local "struct spi_eeprom chip" structure. This happens
after the same structure has been copied into at25->chip. As a result,
at25->chip.byte_len does not contain the correct length of the device.
In turn this can cause checks at beginning of at25_ee_read() to fail
(or equally, it could allow reads beyond the end of the device length).

Fix both of these issues by eliminating the on-stack struct spi_eeprom.
Instead use the one inside at25_data structure, which starts of zeroed.

Fixes: fd307a4ad332 ("nvmem: prepare basics for FRAM support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Link: https://lore.kernel.org/r/20211108181627.645638-1-ralph.siemsen@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The buffer list is sorted and this is not being considered while
calculating packet size. This would lead to improper copy length
calculation for non-dmaheap buffers which would eventually cause
sending improper buffers to DSP.

Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method")
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Jeya R <jeyr@codeaurora.org>
Link: https://lore.kernel.org/r/1637771481-4299-1-git-send-email-jeyr@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull more ACPI updates from Rafael Wysocki:
 "These add support for a new ACPI device configuration object called
  _DSC, fix some issues including one recent regression, add two new
  items to quirk lists and clean up assorted pieces of code.

  Specifics:

   - Add support for new ACPI device configuration object called _DSC
     ("Deepest State for Configuration") to allow certain devices to be
     probed without changing their power states, document it and make
     two drivers use it (Sakari Ailus, Rajmohan Mani).

   - Fix device wakeup power reference counting broken recently by
     mistake (Rafael Wysocki).

   - Drop unused symbol and macros depending on it from acgcc.h (Rafael
     Wysocki).

   - Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).

   - Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
     piece of data from all of the list entries (Hans de Goede).

   - Fix register read accesses handling in the Intel PMIC operation
     region driver (Hans de Goede).

   - Clean up static variables initialization in the EC driver
     (wangzhitong)"

* tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Documentation: ACPI: Fix non-D0 probe _DSC object example
  ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
  ACPI: PM: Fix device wakeup power reference counting error
  ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
  ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
  ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
  ACPI: EC: Remove initialization of static variables to false
  ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
  at24: Support probing while in non-zero ACPI D state
  media: i2c: imx319: Support device probe in non-zero ACPI D state
  ACPI: Add a convenience function to tell a device is in D0 state
  Documentation: ACPI: Document _DSC object usage for enum power state
  i2c: Allow an ACPI driver to manage the device's power state during probe
  ACPI: scan: Obtain device's desired enumeration power state

Pull MFD updates from Lee Jones:
 "Removed Drivers:
   - Remove support for TI TPS80031/TPS80032 PMICs

  New Device Support:
   - Add support for Magnetic Reader to TI AM335x
   - Add support for DA9063_EA to Dialog DA9063
   - Add support for SC2730 PMIC to Spreadtrum SC27xx
   - Add support for MacBookPro16,2 ICL-N UART Intel LPSS PCI
   - Add support for lots of new PMICS in QCom SPMI PMIC
   - Add support for ADC to Diolan DLN2

  New Functionality:
   - Add support for Power Off to Rockchip RK817

  Fix-ups:
   - Simplify Regmap passing to child devices in hi6421-spmi-pmic
   - SPDX licensing updates in ti_am335x_tscadc
   - Improve error handling in ti_am335x_tscadc
   - Expedite clock search in ti_am335x_tscadc
   - Generic simplifications in ti_am335x_tscadc
   - Use generic macros/defines in ti_am335x_tscadc
   - Remove unused code in ti_am335x_tscadc, cros_ec_dev
   - Convert to GPIOD in wcd934x
   - Add namespacing in ti_am335x_tscadc
   - Restrict compilation to relevant arches in intel_pmt
   - Provide better description/documentation in exynos_lpass
   - Add SPI device ID table in altera-a10sr, motorola-cpcap,
     sprd-sc27xx-spi
   - Change IRQ handling in qcom-pm8xxx
   - Split out I2C and SPI code in arizona
   - Explicitly include used headers in altera-a10sr
   - Convert sysfs show() function to in sysfs_emit
   - Standardise *_exit() and *_remove() return values in mc13xxx,
     stmpe, tps65912
   - Trivial (style/spelling/whitespace) fixups in ti_am335x_tscadc,
     qcom-spmi-pmic, max77686-private
   - Device Tree fix-ups in ti,am3359-tscadc, samsung,s2mps11,
     samsung,s2mpa01, samsung,s5m8767, brcm,misc, brcm,cru, syscon,
     qcom,tcsr, xylon,logicvc, max77686, x-powers,ac100,
     x-powers,axp152, x-powers,axp209-gpio, syscon, qcom,spmi-pmic

  Bug Fixes:
   - Balance refcounting (get/put) in ti_am335x_tscadc, mfd-core
   - Fix IRQ trigger type in sec-irq, max77693, max14577
   - Repair off-by-one in altera-sysmgr
   - Add explicit 'select MFD_CORE' to MFD_SIMPLE_MFD_I2C"

* tag 'mfd-next-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (95 commits)
  mfd: simple-mfd-i2c: Select MFD_CORE to fix build error
  mfd: tps80031: Remove driver
  mfd: max77686: Correct tab-based alignment of register addresses
  mfd: wcd934x: Replace legacy gpio interface for gpiod
  dt-bindings: mfd: qcom: pm8xxx: Add pm8018 compatible
  mfd: dln2: Add cell for initializing DLN2 ADC
  mfd: qcom-spmi-pmic: Add missing PMICs supported by socinfo
  mfd: qcom-spmi-pmic: Document ten more PMICs in the binding
  mfd: qcom-spmi-pmic: Sort compatibles in the driver
  mfd: qcom-spmi-pmic: Sort the compatibles in the binding
  mfd: janz-cmoio: Replace snprintf in show functions with sysfs_emit
  mfd: altera-a10sr: Include linux/module.h
  mfd: tps65912: Make tps65912_device_exit() return void
  mfd: stmpe: Make stmpe_remove() return void
  mfd: mc13xxx: Make mc13xxx_common_exit() return void
  dt-bindings: mfd: syscon: Add samsung,exynosautov9-sysreg compatible
  mfd: altera-sysmgr: Fix a mistake caused by resource_size conversion
  dt-bindings: gpio: Convert X-Powers AXP209 GPIO binding to a schema
  dt-bindings: mfd: syscon: Add rk3368 QoS register compatible
  mfd: arizona: Split of_match table into I2C and SPI versions
  ...

Pull cxl updates from Dan Williams:
 "More preparation and plumbing work in the CXL subsystem.

  From an end user perspective the highlight here is lighting up the CXL
  Persistent Memory related commands (label read / write) with the
  generic ioctl() front-end in LIBNVDIMM.

  Otherwise, the ability to instantiate new persistent and volatile
  memory regions is still on track for v5.17.

  Summary:

   - Fix support for platforms that do not enumerate every ACPI0016 (CXL
     Host Bridge) in the CHBS (ACPI Host Bridge Structure).

   - Introduce a common pci_find_dvsec_capability() helper, clean up
     open coded implementations in various drivers.

   - Add 'cxl_test' for regression testing CXL subsystem ABIs.
     'cxl_test' is a module built from tools/testing/cxl/ that mocks up
     a CXL topology to augment the nascent support for emulation of CXL
     devices in QEMU.

   - Convert libnvdimm to use the uuid API.

   - Complete the definition of CXL namespace labels in libnvdimm.

   - Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
     mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.

   - Continue to sort and refactor functionality into distinct driver
     and core-infrastructure buckets. For example, mailbox handling is
     now a generic core capability consumed by the PCI and cxl_test
     drivers"

* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
  ocxl: Use pci core's DVSEC functionality
  cxl/pci: Use pci core's DVSEC functionality
  PCI: Add pci_find_dvsec_capability to find designated VSEC
  cxl/pci: Split cxl_pci_setup_regs()
  cxl/pci: Add @base to cxl_register_map
  cxl/pci: Make more use of cxl_register_map
  cxl/pci: Remove pci request/release regions
  cxl/pci: Fix NULL vs ERR_PTR confusion
  cxl/pci: Remove dev_dbg for unknown register blocks
  cxl/pci: Convert register block identifiers to an enum
  cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
  cxl/pci: Disambiguate cxl_pci further from cxl_mem
  Documentation/cxl: Add bus internal docs
  cxl/core: Split decoder setup into alloc + add
  tools/testing/cxl: Introduce a mock memory device + driver
  cxl/mbox: Move command definitions to common location
  cxl/bus: Populate the target list at decoder create
  tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
  cxl/pmem: Add support for multiple nvdimm-bridge objects
  cxl/pmem: Translate NVDIMM label commands to CXL label commands
  ...

Pull pci updates from Bjorn Helgaas:
 "Enumeration:
   - Conserve IRQs by setting up portdrv IRQs only when there are users
     (Jan Kiszka)
   - Rework and simplify _OSC negotiation for control of PCIe features
     (Joerg Roedel)
   - Remove struct pci_dev.driver pointer since it's redundant with the
     struct device.driver pointer (Uwe Kleine-König)

  Resource management:
   - Coalesce contiguous host bridge apertures from _CRS to accommodate
     BARs that cover more than one aperture (Kai-Heng Feng)

  Sysfs:
   - Check CAP_SYS_ADMIN before parsing user input (Krzysztof
     Wilczyński)
   - Return -EINVAL consistently from "store" functions (Krzysztof
     Wilczyński)
   - Use sysfs_emit() in endpoint "show" functions to avoid buffer
     overruns (Kunihiko Hayashi)

  PCIe native device hotplug:
   - Ignore Link Down/Up caused by resets during error recovery so
     endpoint drivers can remain bound to the device (Lukas Wunner)

  Virtualization:
   - Avoid bus resets on Atheros QCA6174, where they hang the device
     (Ingmar Klein)
   - Work around Pericom PI7C9X2G switch packet drop erratum by using
     store and forward mode instead of cut-through (Nathan Rossi)
   - Avoid trying to enable AtomicOps on VFs; the PF setting applies to
     all VFs (Selvin Xavier)

  MSI:
   - Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
     interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
     Song)

  VPD:
   - Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
     in the possible VPD space; use these to simplify the cxgb3 driver
     (Heiner Kallweit)

  Peer-to-peer DMA:
   - Add (not subtract) the bus offset when calculating DMA address
     (Wang Lu)

  ASPM:
   - Re-enable LTR at Downstream Ports so they don't report Unsupported
     Requests when reset or hot-added devices send LTR messages
     (Mingchuang Qiao)

  Apple PCIe controller driver:
   - Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
     Zyngier)

  Cadence PCIe controller driver:
   - Return success when probe succeeds instead of falling into error
     path (Li Chen)

  HiSilicon Kirin PCIe controller driver:
   - Reorganize PHY logic and add support for external PHY drivers
     (Mauro Carvalho Chehab)
   - Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
     Carvalho Chehab)
   - Add Kirin 970 support (Mauro Carvalho Chehab)
   - Make driver removable (Mauro Carvalho Chehab)

  Intel VMD host bridge driver:
   - If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
     enabled (Adrian Huang)
   - Number each controller so we can tell them apart in
     /proc/interrupts (Chunguang Xu)
   - Avoid building on UML because VMD depends on x86 bare metal APIs
     (Johannes Berg)

  Marvell Aardvark PCIe controller driver:
   - Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
   - Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
   - Downgrade PIO Response Status messages to debug level (Marek Behún)
   - Preserve CRS SV (Config Request Retry Software Visibility) bit in
     emulated Root Control register (Pali Rohár)
   - Fix issue in configuring reference clock (Pali Rohár)
   - Don't clear status bits for masked interrupts (Pali Rohár)
   - Don't mask unused interrupts (Pali Rohár)
   - Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
   - Retry config accesses on CRS response (Pali Rohár)
   - Simplify emulated Root Capabilities initialization (Pali Rohár)
   - Fix several link training issues (Pali Rohár)
   - Fix link-up checking via LTSSM (Pali Rohár)
   - Fix reporting of Data Link Layer Link Active (Pali Rohár)
   - Fix emulation of W1C bits (Marek Behún)
   - Fix MSI domain .alloc() method to return zero on success (Marek
     Behún)
   - Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
     (Marek Behún)
   - Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
     at startup; PCI core will set those as necessary (Pali Rohár)
   - When operating as a Root Port, set class code to "PCI Bridge"
     instead of the default "Mass Storage Controller" (Pali Rohár)
   - Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
     implement this per spec (Pali Rohár)
   - Add emulation of option ROM BAR since aardvark doesn't implement
     this per spec (Pali Rohár)

  MediaTek MT7621 PCIe controller driver:
   - Add MediaTek MT7621 PCIe host controller driver and DT binding
     (Sergio Paracuellos)

  Qualcomm PCIe controller driver:
   - Add SC8180x compatible string (Bjorn Andersson)
   - Add endpoint controller driver and DT binding (Manivannan
     Sadhasivam)
   - Restructure to use of_device_get_match_data() (Prasad Malisetty)
   - Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)

  Renesas R-Car PCIe controller driver:
   - Remove unnecessary includes (Geert Uytterhoeven)

  Rockchip DesignWare PCIe controller driver:
   - Add DT binding (Simon Xue)

  Socionext UniPhier Pro5 controller driver:
   - Serialize INTx masking/unmasking (Kunihiko Hayashi)

  Synopsys DesignWare PCIe controller driver:
   - Run dwc .host_init() method before registering MSI interrupt
     handler so we can deal with pending interrupts left by bootloader
     (Bjorn Andersson)
   - Clean up Kconfig dependencies (Andy Shevchenko)
   - Export symbols to allow more modular drivers (Luca Ceresoli)

  TI DRA7xx PCIe controller driver:
   - Allow host and endpoint drivers to be modules (Luca Ceresoli)
   - Enable external clock if present (Luca Ceresoli)

  TI J721E PCIe driver:
   - Disable PHY when probe fails after initializing it (Christophe
     JAILLET)

  MicroSemi Switchtec management driver:
   - Return error to application when command execution fails because an
     out-of-band reset has cleared the device BARs, Memory Space Enable,
     etc (Kelvin Cao)
   - Fix MRPC error status handling issue (Kelvin Cao)
   - Mask out other bits when reading of management VEP instance ID
     (Kelvin Cao)
   - Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
     (Kelvin Cao)
   - Add check of event support (Logan Gunthorpe)

  Miscellaneous:
   - Remove unused pci_pool wrappers, which have been replaced by
     dma_pool (Cai Huoqing)
   - Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
     Wilczyński)
   - Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
     Wilczyński)
   - Fix some sscanf(), sprintf() format mismatches (Krzysztof
     Wilczyński)
   - Update PCI subsystem information in MAINTAINERS (Krzysztof
     Wilczyński)
   - Correct some misspellings (Krzysztof Wilczyński)"

* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
  PCI: Add ACS quirk for Pericom PI7C9X2G switches
  PCI: apple: Configure RID to SID mapper on device addition
  iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
  PCI: apple: Implement MSI support
  PCI: apple: Add INTx and per-port interrupt support
  PCI: kirin: Allow removing the driver
  PCI: kirin: De-init the dwc driver
  PCI: kirin: Disable clkreq during poweroff sequence
  PCI: kirin: Move the power-off code to a common routine
  PCI: kirin: Add power_off support for Kirin 960 PHY
  PCI: kirin: Allow building it as a module
  PCI: kirin: Add MODULE_* macros
  PCI: kirin: Add Kirin 970 compatible
  PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
  PCI: apple: Set up reference clocks when probing
  PCI: apple: Add initial hardware bring-up
  PCI: of: Allow matching of an interrupt-map local to a PCI device
  of/irq: Allow matching of an interrupt-map local to an interrupt controller
  irqdomain: Make of_phandle_args_to_fwspec() generally available
  PCI: Do not enable AtomicOps on VFs
  ...

Pull char/misc driver updates from Greg KH:
 "Here is the big set of char and misc and other tiny driver subsystem
  updates for 5.16-rc1.

  Loads of things in here, all of which have been in linux-next for a
  while with no reported problems (except for one called out below.)

  Included are:

   - habanana labs driver updates, including dma_buf usage, reviewed and
     acked by the dma_buf maintainers

   - iio driver update (going through this tree not staging as they
     really do not belong going through that tree anymore)

   - counter driver updates

   - hwmon driver updates that the counter drivers needed, acked by the
     hwmon maintainer

   - xillybus driver updates

   - binder driver updates

   - extcon driver updates

   - dma_buf module namespaces added (will cause a build error in arm64
     for allmodconfig, but that change is on its way through the drm
     tree)

   - lkdtm driver updates

   - pvpanic driver updates

   - phy driver updates

   - virt acrn and nitr_enclaves driver updates

   - smaller char and misc driver updates"

* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
  comedi: dt9812: fix DMA buffers on stack
  comedi: ni_usb6501: fix NULL-deref in command paths
  arm64: errata: Enable TRBE workaround for write to out-of-range address
  arm64: errata: Enable workaround for TRBE overwrite in FILL mode
  coresight: trbe: Work around write to out of range
  coresight: trbe: Make sure we have enough space
  coresight: trbe: Add a helper to determine the minimum buffer size
  coresight: trbe: Workaround TRBE errata overwrite in FILL mode
  coresight: trbe: Add infrastructure for Errata handling
  coresight: trbe: Allow driver to choose a different alignment
  coresight: trbe: Decouple buffer base from the hardware base
  coresight: trbe: Add a helper to pad a given buffer area
  coresight: trbe: Add a helper to calculate the trace generated
  coresight: trbe: Defer the probe on offline CPUs
  coresight: trbe: Fix incorrect access of the sink specific data
  coresight: etm4x: Add ETM PID for Kryo-5XX
  coresight: trbe: Prohibit trace before disabling TRBE
  coresight: trbe: End the AUX handle on truncation
  coresight: trbe: Do not truncate buffer on IRQ
  coresight: trbe: Fix handling of spurious interrupts
  ...

In certain use cases (where the chip is part of a camera module, and the
camera module is wired together with a camera privacy LED), powering on
the device during probe is undesirable. Add support for the at24 to
execute probe while being in ACPI D state other than 0 (which means fully
powered on).

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull drm updates from Dave Airlie:
 "Summary below. i915 starts to add support for DG2 GPUs, enables DG1
  and ADL-S support by default, lots of work to enable DisplayPort 2.0
  across drivers. Lots of documentation updates and fixes across the
  board.

  core:
   - improve dma_fence, lease and resv documentation
   - shmem-helpers: allocate WC pages on x86, use vmf_insert_pin
   - sched fixes/improvements
   - allow empty drm leases
   - add dma resv iterator
   - add more DP 2.0 headers
   - DP MST helper improvements for DP2.0

  dma-buf:
   - avoid warnings, remove fence trace macros

  bridge:
   - new helper to get rid of panels
   - probe improvements for it66121
   - enable DSI EOTP for anx7625

  fbdev:
   - efifb: release runtime PM on destroy

  ttm:
   - kerneldoc switch
   - helper to clear all DMA mappings
   - pool shrinker optimizaton
   - remove ttm_tt_destroy_common
   - update ttm_move_memcpy for async use

  panel:
   - add new panel-edp driver

  amdgpu:
   - Initial DP 2.0 support
   - Initial USB4 DP tunnelling support
   - Aldebaran MCE support
   - Modifier support for DCC image stores for GFX 10.3
   - Display rework for better FP code handling
   - Yellow Carp/Cyan Skillfish updates
   - Cyan Skillfish display support
   - convert vega/navi to IP discovery asic enumeration
   - validate IP discovery table
   - RAS improvements
   - Lots of fixes

  i915:
   - DG1 PCI IDs + LMEM discovery/placement
   - DG1 GuC submission by default
   - ADL-S PCI IDs updated + enabled by default
   - ADL-P (XE_LPD) fixed and updates
   - DG2 display fixes
   - PXP protected object support for Gen12 integrated
   - expose multi-LRC submission interface for GuC
   - export logical engine instance to user
   - Disable engine bonding on Gen12+
   - PSR cleanup
   - PSR2 selective fetch by default
   - DP 2.0 prep work
   - VESA vendor block + MSO use of it
   - FBC refactor
   - try again to fix fast-narrow vs slow-wide eDP training
   - use THP when IOMMU enabled
   - LMEM backup/restore for suspend/resume
   - locking simplification
   - GuC major reworking
   - async flip VT-D workaround changes
   - DP link training improvements
   - misc display refactorings

  bochs:
   - new PCI ID

  rcar-du:
   - Non-contiguious buffer import support for rcar-du
   - r8a779a0 support prep

  omapdrm:
   - COMPILE_TEST fixes

  sti:
   - COMPILE_TEST fixes

  msm:
   - fence ordering improvements
   - eDP support in DP sub-driver
   - dpu irq handling cleanup
   - CRC support for making igt happy
   - NO_CONNECTOR bridge support
   - dsi: 14nm phy support for msm8953
   - mdp5: msm8x53, sdm450, sdm632 support

  stm:
   - layer alpha + zpo support

  v3d:
   - fix Vulkan CTS failure
   - support multiple sync objects

  gud:
   - add R8/RGB332/RGB888 pixel formats

  vc4:
   - convert to new bridge helpers

  vgem:
   - use shmem helpers

  virtio:
   - support mapping exported vram

  zte:
   - remove obsolete driver

  rockchip:
   - use bridge attach no connector for LVDS/RGB"

* tag 'drm-next-2021-11-03' of git://anongit.freedesktop.org/drm/drm: (1259 commits)
  drm/amdgpu/gmc6: fix DMA mask from 44 to 40 bits
  drm/amd/display: MST support for DPIA
  drm/amdgpu: Fix even more out of bound writes from debugfs
  drm/amdgpu/discovery: add SDMA IP instance info for soc15 parts
  drm/amdgpu/discovery: add UVD/VCN IP instance info for soc15 parts
  drm/amdgpu/UAPI: rearrange header to better align related items
  drm/amd/display: Enable dpia in dmub only for DCN31 B0
  drm/amd/display: Fix USB4 hot plug crash issue
  drm/amd/display: Fix deadlock when falling back to v2 from v3
  drm/amd/display: Fallback to clocks which meet requested voltage on DCN31
  drm/amd/display: move FPU associated DCN301 code to DML folder
  drm/amd/display: fix link training regression for 1 or 2 lane
  drm/amd/display: add two lane settings training options
  drm/amd/display: decouple hw_lane_settings from dpcd_lane_settings
  drm/amd/display: implement decide lane settings
  drm/amd/display: adopt DP2.0 LT SCR revision 8
  drm/amd/display: FEC configuration for dpia links in MST mode
  drm/amd/display: FEC configuration for dpia links
  drm/amd/display: Add workaround flag for EDID read on certain docks
  drm/amd/display: Set phy_mux_sel bit in dmub scratch register
  ...