linux.git/drivers/mmc/core, branch v4.4.117

mmc: core: Do not leave the block driver in a suspended state

2017-12-05T10:22:51+00:00

commit ebe7dd45cf49e3b49cacbaace17f9f878f21fbea upstream.

The block driver must be resumed if the mmc bus fails to suspend the card.

Signed-off-by: Adrian Hunter 
Reviewed-by: Linus Walleij 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdio: fix alignment issue in struct sdio_func

2017-10-08T08:14:19+00:00

[ Upstream commit 5ef1ecf060f28ecef313b5723f1fd39bf5a35f56 ]

Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.

Signed-off-by: Heiner Kallweit 
Tested-by: Helmut Klein 
Signed-off-by: Ulf Hansson 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

mmc: core: fix multi-bit bus width without high-speed mode

2017-02-23T16:43:10+00:00

commit 3d4ef329757cfd5e0b23cce97cdeca7e2df89c99 upstream.

Commit 577fb13199b1 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().

However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.

This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.

Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.

Tested with a Zynq-7000 PicoZed 7020 board.

Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula 
Signed-off-by: Ulf Hansson 
[anssi.hannula@bitwise.fi: backported for the different err variable
 check on v4.4 and tested]
Signed-off-by: Greg Kroah-Hartman

mmc: longer timeout for long read time quirk

2016-06-01T19:15:50+00:00

commit 32ecd320db39bcb007679ed42f283740641b81ea upstream.

008GE0 Toshiba mmc in some Intel Baytrail tablets responds to
MMC_SEND_EXT_CSD in 450-600ms.

This patch will...

() Increase the long read time quirk timeout from 300ms to 600ms. Original
   author of that quirk says 300ms was only a guess and that the number
   may need to be raised in the future.

() Add this specific MMC to the quirk

Signed-off-by: Matt Gumbel 
Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: mmc: Fix partition switch timeout for some eMMCs

2016-06-01T19:15:50+00:00

commit 1c447116d017a98c90f8f71c8c5a611e0aa42178 upstream.

Some eMMCs set the partition switch timeout too low.

Now typically eMMCs are considered a critical component (e.g. because
they store the root file system) and consequently are expected to be
reliable.  Thus we can neglect the use case where eMMCs can't switch
reliably and we might want a lower timeout to facilitate speedy
recovery.

Although we could employ a quirk for the cards that are affected (if
we could identify them all), as described above, there is little
benefit to having a low timeout, so instead simply set a minimum
timeout.

The minimum is set to 300ms somewhat arbitrarily - the examples that
have been seen had a timeout of 10ms but were sometimes taking 60-70ms.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: core: Enable tuning according to the actual timing

2016-03-03T23:07:15+00:00

commit e10c321977091f163eceedec0650e0ef4b3cf4bb upstream.

While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.

This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.

With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.

Signed-off-by: Carlo Caione 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: mmc: Fix incorrect use of driver strength switching HS200 and HS400

2016-03-03T23:07:15+00:00

commit adb24d42a516bca8b9741ed21206509daaab5b13 upstream.

Commit cc4f414c885c ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode.  While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.

Signed-off-by: Wenkai Du 
Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: sdio: Fix invalid vdd in voltage switch power cycle

2016-03-03T23:07:15+00:00

commit d9bfbb95ed598a09cf336adb0f190ee0ff802f0d upstream.

The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage.  However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd.  Fix by passing the card's
ocr value which does not have the flag.

Signed-off-by: Adrian Hunter 
Signed-off-by: Ulf Hansson 
Signed-off-by: Greg Kroah-Hartman

mmc: mmc: Improve reliability of mmc_select_hs400()

2015-11-09T12:16:32+00:00

mmc_select_hs400() calls __mmc_switch() which checks the switch is
successful using CMD13 (SEND_STATUS).  The problem is that it does that
using the timing settings of the previous mode.  That is prone to error,
especially when switching from HS to HS400 because the timing parameters
for HS mode are tighter than the timing parameters for HS400 mode.

In the case when CMD13 polling is used (i.e. not MMC_CAP_WAIT_WHILE_BUSY)
with the switch command, it must be assumed that using different modes on
the card and host must work.

However in the case when CMD13 polling is not used
(i.e. MMC_CAP_WAIT_WHILE_BUSY) mmc_select_hs400() can be made more
reliable by setting the host to the correct timing before sending CMD13.

This patch does that.

Signed-off-by: Adrian Hunter 
Cc:  # 4.2+
Tested-by: Alim Akhtar 
Signed-off-by: Ulf Hansson

mmc: mmc: Move mmc_switch_status()

2015-11-09T12:16:26+00:00

Move the mmc_switch_status() function in preparation for calling it
in mmc_select_hs400().

Signed-off-by: Adrian Hunter 
Cc:  # 4.2+
Tested-by: Alim Akhtar 
Signed-off-by: Ulf Hansson