linux.git/drivers/net, branch v2.6.17.10

e1000: add forgotten PCI ID for supported device

2006-08-07T03:52:15+00:00

The Intel(R) PRO/1000 82572EI card is fully supported by 7.0.33-k2 and
onward.  Add the device ID so this card works with 2.6.17.y onward. This
device ID was accidentally omitted.

Signed-off-by: Auke Kok 
Signed-off-by: Greg Kroah-Hartman

sky2: NAPI bug

2006-08-07T03:52:14+00:00

If the sky2 driver decides to defer processing because it's NAPI
packet quota is done, then it won't correctly handle the rest
when it is rescheduled.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Greg Kroah-Hartman

via-velocity: the link is not correctly detected when the device starts

2006-07-25T03:35:21+00:00

via-velocity: the link is not correctly detected when the device starts

The patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=6711

Signed-off-by: Roy Marples 
Signed-off-by: Francois Romieu 
Signed-off-by: Chris Wright 
Signed-off-by: Greg Kroah-Hartman

[PATCH] bcm43xx: init fix for possible Machine Check

2006-06-30T00:17:16+00:00

Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.

Signed-off-by: Michael Buesch 
Signed-off-by: Chris Wright

[PATCH] sky2: netconsole suspend/resume interaction

2006-06-17T17:52:12+00:00

A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.

This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: stop/start hardware idle timer on suspend/resume

2006-06-13T20:16:41+00:00

The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend.  Also disable hardware IRQ's
on suspend.  Will need to revisit this with hotplug?

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: save/restore base hardware irq during suspend/resume

2006-06-13T20:16:41+00:00

The hardware should be fully shut off during suspend, and the base
irq mask restored during resume.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: fix hotplug detect during poll

2006-06-13T20:16:41+00:00

If the poll routine detects no hardware available, it needs to dequeue
it self from the network poll list. Linus didn't understand NAPI.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: don't hard code number of ports

2006-06-13T20:16:41+00:00

It is cleaner, to not loop over both ports if only one exists.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds

[PATCH] sky2: set_power_state should be void

2006-06-13T20:16:40+00:00

The set power state function is cleaner if it doesn't return anything.
The only caller that could fail is in suspend() and it can check the argument
there.

Signed-off-by: Stephen Hemminger 
Signed-off-by: Linus Torvalds