linux.git/drivers/pci/probe.c, branch v4.4.177

PCI: Skip MPS logic for Virtual Functions (VFs)

2018-08-24T11:27:01+00:00

commit 3dbe97efe8bf450b183d6dee2305cbc032e6b8a4 upstream.

PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs.  Just prior to the table it states:

  "PF and VF functionality is defined in Section 7.5.3.4 except where
   noted in Table 9-16.  For VF fields marked 'RsvdP', the PF setting
   applies to the VF."

All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's.  Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Fixes: 27d868b5e6cf ("PCI: Set MPS to match upstream bridge")
Signed-off-by: Myron Stowe 
Signed-off-by: Bjorn Helgaas 
Cc: stable@vger.kernel.org # 4.3+
Cc: Keith Busch 
Cc: Sinan Kaya 
Cc: Dongdong Liu 
Cc: Jon Mason 
Signed-off-by: Greg Kroah-Hartman

PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant

2018-04-08T09:51:57+00:00

commit 76dc52684d0f72971d9f6cc7d5ae198061b715bd upstream.

A 64-bit value is not needed since a PCI ROM address consists in 32 bits.
This fixes a clang warning about "implicit conversion from 'unsigned long'
to 'u32'".

Also remove now unnecessary casts to u32 from __pci_read_base() and
pci_std_update_resource().

Signed-off-by: Matthias Kaehlcke 
Signed-off-by: Bjorn Helgaas 
Cc: Nathan Chancellor 
Signed-off-by: Greg Kroah-Hartman

PCI: Apply _HPX settings only to relevant devices

2017-11-30T08:37:26+00:00

[ Upstream commit 977509f7c5c6fb992ffcdf4291051af343b91645 ]

Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.

We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.

We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings.  I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm.  But it's
ugly to depend on those internals.

Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).

A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:

  pci 0000:00:00.0: PCI-X settings not supported

After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731
Signed-off-by: Bjorn Helgaas 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE

2017-03-30T07:35:19+00:00

From: Bjorn Helgaas 

[ Upstream commit 7a6d312b50e63f598f5b5914c4fd21878ac2b595 ]

Remove the assumption that IORESOURCE_ROM_ENABLE == PCI_ROM_ADDRESS_ENABLE.
PCI_ROM_ADDRESS_ENABLE is the ROM enable bit defined by the PCI spec, so if
we're reading or writing a BAR register value, that's what we should use.
IORESOURCE_ROM_ENABLE is a corresponding bit in struct resource flags.

Signed-off-by: Bjorn Helgaas 
Reviewed-by: Gavin Shan 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sumit Semwal 
Signed-off-by: Greg Kroah-Hartman

PCI: Enumerate switches below PCI-to-PCIe bridges

2017-01-26T07:23:48+00:00

commit 51ebfc92b72b4f7dac1ab45683bf56741e454b8c upstream.

A PCI-to-PCIe bridge (a "reverse bridge") has a PCI or PCI-X primary
interface and a PCI Express secondary interface.  The PCIe interface is a
Downstream Port that originates a Link.  See the "PCI Express to PCI/PCI-X
Bridge Specification", rev 1.0, sections 1.2 and A.6.

The bug report below involves a PCI-to-PCIe bridge and a PCIe switch below
the bridge:

  00:1e.0 Intel 82801 PCI Bridge to [bus 01-0a]
  01:00.0 Pericom PI7C9X111SL PCIe-to-PCI Reversible Bridge to [bus 02-0a]
  02:00.0 Pericom Device 8608 [PCIe Upstream Port] to [bus 03-0a]
  03:01.0 Pericom Device 8608 [PCIe Downstream Port] to [bus 0a]

01:00.0 is configured as a PCI-to-PCIe bridge (despite the name printed by
lspci).  As we traverse a PCIe hierarchy, device connections alternate
between PCIe Links and internal Switch logic.  Previously we did not
recognize that 01:00.0 had a secondary link, so we thought the 02:00.0
Upstream Port *did* have a secondary link.  In fact, it's the other way
around: 01:00.0 has a secondary link, and 02:00.0 has internal Switch logic
on its secondary side.

When we thought 02:00.0 had a secondary link, the pci_scan_slot() ->
only_one_child() path assumed 02:00.0 could have only one child, so 03:00.0
was the only possible downstream device.  But 03:00.0 doesn't exist, so we
didn't look for any other devices on bus 03.

Booting with "pci=pcie_scan_all" is a workaround, but we don't want users
to have to do that.

Recognize that PCI-to-PCIe bridges originate links on their secondary
interfaces.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=189361
Fixes: d0751b98dfa3 ("PCI: Add dev->has_secondary_link to track downstream PCIe links")
Tested-by: Blake Moore 
Signed-off-by: Bjorn Helgaas 
Signed-off-by: Greg Kroah-Hartman

PCI: Set Read Completion Boundary to 128 iff Root Port supports it (_HPX)

2016-12-08T06:15:24+00:00

commit e42010d8207f9d15a605ceb8e321bcd9648071b0 upstream.

Per PCIe spec r3.0, sec 2.3.1.1, the Read Completion Boundary (RCB)
determines the naturally aligned address boundaries on which a Read Request
may be serviced with multiple Completions:

  - For a Root Complex, RCB is 64 bytes or 128 bytes
    This value is reported in the Link Control Register

    Note: Bridges and Endpoints may implement a corresponding command bit
    which may be set by system software to indicate the RCB value for the
    Root Complex, allowing the Bridge/Endpoint to optimize its behavior
    when the Root Complex’s RCB is 128 bytes.

  - For all other system elements, RCB is 128 bytes

Per sec 7.8.7, if a Root Port only supports a 64-byte RCB, the RCB of all
downstream devices must be clear, indicating an RCB of 64 bytes.  If the
Root Port supports a 128-byte RCB, we may optionally set the RCB of
downstream devices so they know they can generate larger Completions.

Some BIOSes supply an _HPX that tells us to set RCB, even though the Root
Port doesn't have RCB set, which may lead to Malformed TLP errors if the
Endpoint generates completions larger than the Root Port can handle.

The IBM x3850 X6 with BIOS version -[A8E120CUS-1.30]- 08/22/2016 supplies
such an _HPX and a Mellanox MT27500 ConnectX-3 device fails to initialize:

  mlx4_core 0000:41:00.0: command 0xfff timed out (go bit not cleared)
  mlx4_core 0000:41:00.0: device is going to be reset
  mlx4_core 0000:41:00.0: Failed to obtain HW semaphore, aborting
  mlx4_core 0000:41:00.0: Fail to reset HCA
  ------------[ cut here ]------------
  kernel BUG at drivers/net/ethernet/mellanox/mlx4/catas.c:193!

After 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration")
and 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices
with a link"), we apply _HPX settings to *all* devices, not just those
hot-added after boot.

Before 7a1562d4f2d0, we didn't touch the Mellanox RCB, and the device
worked.  After 7a1562d4f2d0, we set its RCB to 128, and it failed.

Set the RCB to 128 iff the Root Port supports a 128-byte RCB.  Otherwise,
set RCB to 64 bytes.  This effectively ignores what _HPX tells us about
RCB.

Note that this change only affects _HPX handling.  If we have no _HPX, this
does nothing with RCB.

[bhelgaas: changelog, clear RCB if not set for Root Port]
Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration")
Fixes: 7a1562d4f2d0 ("PCI: Apply _HPX Link Control settings to all devices with a link")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187781
Tested-by: Frank Danapfel 
Signed-off-by: Johannes Thumshirn 
Signed-off-by: Bjorn Helgaas 
Acked-by: Myron Stowe 
Signed-off-by: Greg Kroah-Hartman

PCI: Disable all BAR sizing for devices with non-compliant BARs

2016-06-08T01:14:35+00:00

commit ad67b437f187ea818b2860524d10f878fadfdd99 upstream.

b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec.  But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:

  pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]

Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.

Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check.  We haven't had reports of devices with broken SR-IOV
BARs yet.

[bhelgaas: changelog]
Fixes: b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava 
Signed-off-by: Bjorn Helgaas 
CC: Thomas Gleixner 
CC: Ingo Molnar 
CC: "H. Peter Anvin" 
CC: Andi Kleen 
Signed-off-by: Greg Kroah-Hartman

PCI: Disable IO/MEM decoding for devices with non-compliant BARs

2016-04-12T16:08:37+00:00

commit b84106b4e2290c081cdab521fa832596cdfea246 upstream.

The PCI config header (first 64 bytes of each device's config space) is
defined by the PCI spec so generic software can identify the device and
manage its usage of I/O, memory, and IRQ resources.

Some non-spec-compliant devices put registers other than BARs where the
BARs should be.  When the PCI core sizes these "BARs", the reads and writes
it does may have unwanted side effects, and the "BAR" may appear to
describe non-sensical address space.

Add a flag bit to mark non-compliant devices so we don't touch their BARs.
Turn off IO/MEM decoding to prevent the devices from consuming address
space, since we can't read the BARs to find out what that address space
would be.

Signed-off-by: Bjorn Helgaas 
Tested-by: Andi Kleen 
Signed-off-by: Greg Kroah-Hartman

Merge branches 'acpi-smbus', 'acpi-ec' and 'acpi-pci'

2015-11-20T00:22:52+00:00

* acpi-smbus:
  Revert "ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook"
  ACPI / SMBus: Fix boot stalls / high CPU caused by reentrant code

* acpi-ec:
  ACPI-EC: Drop unnecessary check made before calling acpi_ec_delete_query()

* acpi-pci:
  PCI: Fix OF logic in pci_dma_configure()

PCI: Fix OF logic in pci_dma_configure()

2015-11-20T00:20:36+00:00

This patch fixes a bug introduced by previous commit,
which incorrectly checkes the of_node of the end-point device.
Instead, it should check the of_node of the host bridge.

Fixes: 50230713b639 ("PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()")
Reported-by: Robin Murphy 
Signed-off-by: Suravee Suthikulpanit 
Acked-by: Arnd Bergmann 
Signed-off-by: Rafael J. Wysocki