linux.git/drivers/pci, branch v4.1.10

PCI,parisc: Enable 64-bit bus addresses on PA-RISC

2015-09-29T17:26:11+00:00

commit e02a653e15d8d32e9e768fd99a3271aafe5c5d77 upstream.

Commit 3a9ad0b ("PCI: Add pci_bus_addr_t") unconditionally introduced usage of
64-bit PCI bus addresses on all 64-bit platforms which broke PA-RISC.

It turned out that due to enabling the 64-bit addresses, the PCI logic decided
to use the GMMIO instead of the LMMIO region. This commit simply disables
registering the GMMIO and thus we fall back to use the LMMIO region as before.

Reverts commit 45ea2a5fed6dacb9bb0558d8b21eacc1c45d5bb4
("PCI: Don't use 64-bit bus addresses on PA-RISC")

To: linux-parisc@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas 
Cc: Meelis Roos 
Signed-off-by: Helge Deller 
Signed-off-by: Greg Kroah-Hartman

PCI: Disable async suspend/resume for JMicron multi-function SATA/AHCI

2015-09-21T17:05:34+00:00

commit 91f15fb30c77d4a0d0d9b97e5cec647650853145 upstream.

On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0.  The result is that PATA doesn't work after resume, and we
print messages like this:

  pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
  irq 17: nobody cared (try booting with the "irqpoll" option)

Async resume was introduced in v3.15 by 76569faa62c4 ("PM / sleep:
Asynchronous threads for resume_noirq").  Prior to that, we powered on
the functions in order, so this problem shouldn't happen.

e6b7e41cdd8c ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices.  With async suspend
disabled, we always power on function 0 before function 1.

Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).

Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.

This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume.  Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.

[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto 
Signed-off-by: Zhang Rui 
Signed-off-by: Bjorn Helgaas 
Signed-off-by: Greg Kroah-Hartman

PCI: Add VPD function 0 quirk for Intel Ethernet devices

2015-09-21T17:05:33+00:00

commit 7aa6ca4d39edf01f997b9e02cf6d2fdeb224f351 upstream.

Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.

[bhelgaas: changelog]
Signed-off-by: Mark Rustad 
Signed-off-by: Bjorn Helgaas 
Acked-by: Alexander Duyck 
Signed-off-by: Greg Kroah-Hartman

PCI: Add dev_flags bit to access VPD through function 0

2015-09-21T17:05:33+00:00

commit 932c435caba8a2ce473a91753bad0173269ef334 upstream.

Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions.  This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions.  Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.

On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang.  This has to do with how the kernel tracks the expected value of the
F bit per function.

Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.

When hangs occur, typically the error message:

  vpd r/w failed.  This is likely a firmware bug on this device.

will be seen.

Never set this bit on function 0 or there will be an infinite recursion.

Signed-off-by: Mark Rustad 
Signed-off-by: Bjorn Helgaas 
Acked-by: Alexander Duyck 
Signed-off-by: Greg Kroah-Hartman

PCI: Fix TI816X class code quirk

2015-09-21T17:05:33+00:00

commit d1541dc977d376406f4584d8eb055488655c98ec upstream.

In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.

Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.

Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas 
CC: Hemant Pedanekar 
Signed-off-by: Greg Kroah-Hartman

PCI: Don't use 64-bit bus addresses on PA-RISC

2015-09-13T16:07:49+00:00

commit 45ea2a5fed6dacb9bb0558d8b21eacc1c45d5bb4 upstream.

Meelis and Helge reported that 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.

PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4fdcd, we always used 32-bit PCI addresses.  After
3a9ad0b4fdcd, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.

Fixes: 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
Link: http://lkml.kernel.org/r/alpine.LRH.2.11.1507260929000.30065@math.ut.ee
Reported-by: Meelis Roos 
Reported-by: Helge Deller 
Tested-by: Helge Deller 
Based-on-idea-by: Yinghai Lu 
Signed-off-by: Bjorn Helgaas 
Acked-by: Yinghai Lu 
Signed-off-by: Greg Kroah-Hartman

PCI: pciehp: Wait for hotplug command completion where necessary

2015-07-21T17:10:05+00:00

commit a5dd4b4b0570b3bf880d563969b245dfbd170c1e upstream.

The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously.  Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed.  In cases
where we need that state change to be enabled, we must still wait for
completion.  For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection.  If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.

Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion.  The following
functions are returned to their previous behavior:

  pciehp_power_on_slot
  pciehp_power_off_slot
  pcie_disable_notification
  pciehp_reset_slot

The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on.  pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected.  And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.

Fixes: 3461a068661c ("PCI: pciehp: Wait for hotplug command completion lazily")
Signed-off-by: Alex Williamson 
Signed-off-by: Bjorn Helgaas 
Signed-off-by: Greg Kroah-Hartman

PCI: Add pci_bus_addr_t

2015-07-21T17:10:05+00:00

commit 3a9ad0b4fdcd57f775d3615004c8c64c021a9e7d upstream.

David Ahern reported that d63e2e1f3df9 ("sparc/PCI: Clip bridge windows
to fit in upstream windows") fails to boot on sparc/T5-8:

pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)

The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3df9 added new checking that
tripped over this mismatch.

Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.

[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at
least as wide as dma_addr_t, documentation]
Fixes: d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Fixes: 23b13bc76f35 ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com
Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231
Reported-by: David Ahern
Tested-by: David Ahern
Signed-off-by: Yinghai Lu
Signed-off-by: Bjorn Helgaas
Acked-by: David S. Miller
Signed-off-by: Greg Kroah-Hartman

PCI: Propagate the "ignore hotplug" setting to parent

2015-07-21T17:10:05+00:00

commit 0824965140fff1bf640a987dc790d1594a8e0699 upstream.

Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the
ignore_hotplug setting of the device to its parent bridge in case hotplug
notifications related to the graphics adapter switching are given for the
bridge rather than for the device itself (they need to be ignored in both
cases).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891
Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927
Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Reported-and-tested-by: tiagdtd-lava 
Signed-off-by: Rafael J. Wysocki 
Signed-off-by: Bjorn Helgaas 
Signed-off-by: Greg Kroah-Hartman

PCI: Preserve resource size during alignment reordering

2015-06-01T22:56:32+00:00

In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.

In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus.  Even if we'd had the correct size, the end would
have been off by one.

Preserve the resource size when we adjust its alignment.

[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Yinghai Lu 
Signed-off-by: Bjorn Helgaas 
Acked-by: Wei Yang 
CC: Benjamin Herrenschmidt