linux.git/drivers/pinctrl/sunxi, branch v4.9.294

pinctrl: sunxi: a83t: Fix IRQ offset typo for PH11

2018-12-21T13:11:30+00:00

commit 478b6767ad26ab86d9ecc341027dd09a87b1f997 upstream.

Pin PH11 is used on various A83T board to detect a change in the OTG
port's ID pin, as in when an OTG host cable is plugged in.

The incorrect offset meant the gpiochip/irqchip was activating the wrong
pin for interrupts.

Fixes: 4730f33f0d82 ("pinctrl: sunxi: add allwinner A83T PIO controller support")
Cc: 
Signed-off-by: Chen-Yu Tsai 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: sunxi: Fix A64 UART mux value

2018-02-25T10:05:46+00:00

[ Upstream commit 7c5c2c2d18d778e51fd8b899965097168306031c ]

To use pin PF4 as the RX signal of UART0, we have to write 0b011 into
the respective pin controller register.
Fix the wrong value we had in our table so far.

Fixes: 96851d391d02 ("drivers: pinctrl: add driver for Allwinner A64 SoC")
Signed-off-by: Andre Przywara 
Acked-by: Chen-Yu Tsai 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: sunxi: Fix A80 interrupt pin bank

2018-02-25T10:05:46+00:00

[ Upstream commit 6ad4cc8d1ac483e0fd33f605fb2788b0ecf51ed4 ]

On the A80 the pins on port B can trigger interrupts, and those are
assigned to the second interrupt bank.
Having two pins assigned to the same interrupt bank/pin combination does
not look healthy (instead more like a copy&paste bug from pins PA14-PA16),
so fix the interrupt bank for pins PB14-PB16, which is actually 1.

I don't have any A80 board, so could not test this.

Fixes: d5e9fb31baa2 ("pinctrl: sunxi: Add A80 pinctrl muxing options")
Signed-off-by: Andre Przywara 
Acked-by: Chen-Yu Tsai 
Signed-off-by: Linus Walleij 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver

2017-08-16T20:43:22+00:00

commit d81ece747d8727bb8b1cfc9a20dbe62f09a4e35a upstream.

The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.

This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.

Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.

Fixes: f2821b1ca3a2 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")

Signed-off-by: Icenowy Zheng 
Reviewed-by: Chen-Yu Tsai 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

pinctrl: sunxi: Fix SPDIF function name for A83T

2017-07-12T13:01:05+00:00

commit 7903d4f5e1dec53963cba9b1bc472a76a3532e07 upstream.

We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..

Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.

Fixes: 4730f33f0d82 ("pinctrl: sunxi: add allwinner A83T PIO controller
		      support")
Signed-off-by: Chen-Yu Tsai 
Acked-by: Maxime Ripard 
Signed-off-by: Linus Walleij 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

2016-10-05T18:49:09+00:00

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.9 series:

  Subsystem improvements:

   - do away with the last users of the obsolete Kconfig options
     ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
     always sounded like an item on a wishlist to Santa Claus to me). We
     can now select GPIOLIB and be done with it, for all archs. After
     some struggle it even work on UM. Not that it has GPIO, but if it
     wants to, it can select the library.

   - continued efforts to make drivers properly either tristate or bool.

   - introduce a warning for drivers assigning default triggers to their
     irqchip lines when probed from device tree, so we find and fix
     these ambigous drivers. It is agreed that in the OF config path,
     the device tree defines trigger characteristics.

   - the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.

   - we introduce the ability to mark certain IRQ lines as "unusable" as
     they can be taken by BIOS/firmware, unrouted in silicon and
     generally nasty if you use them, and such things. This is put to
     good use in the STMPE driver and also in the Cherryview pin control
     driver.

   - a new "mockup" virtual GPIO device that can be used for testing.
     The plan is to add unit tests under tools/* for exercising this
     device and verify that the kernel code paths are working as they
     should.

   - make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
     implicit all the time, but when people started building UM with
     allyesconfig or allmodconfig it exploded in their face.

   - move some stray bits of device tree and ACPI HW description
     callbacks down into their respective implementation silo. These
     were causing issues when compiling on !HAS_IOMEM as well, so now
     eventually UM compiles the GPIOLIB library if it wants to.

  New drivers:

   - new driver for the Aspeed GPIO front-end companion to the pin
     controller merged through the pin control tree.

   - new driver for the LP873x PMIC GPIO portions.

   - new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
     TS-7970, TS-7990 and TS-4100.

   - new driver for the Broadcom BCM63xx series including BCM6338 and
     BCM6345.

   - new driver for the Intel WhiskeyCove PMIC GPIO.

   - new driver for the Allwinner AXP209 PMIC GPIO portions.

   - new driver for Diamond Systems 48 line GPIO-MM, another of these
     port-mapped I/O expansion cards.

   - support the STMicroelectronics STMPE1600 variant in the STMPE
     driver.

  Driver improvements:

   - the STMPE driver now supports rising/falling edge detection
     properly for IRQs.

   - the PCA954x will now fetch and enable its VCC regulator properly.

   - major rework of the PCA953x driver with the goal of eventually
     switching it over to use regmap and thus modernize it even more.

   - switch the IOP driver to use the generic MMIO GPIO library.

   - move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
     over to this subsystem from MFD, achieveing some separation of
     concerns"

* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
  gpio: add missing static inline
  gpio: OF: localize some gpiochip init functions
  gpio: acpi: separation of concerns
  gpio: OF: separation of concerns
  gpio: make memory-mapped drivers depend on HAS_IOMEM
  gpio: stmpe: use BIT() macro
  gpio: stmpe: forbid unused lines to be mapped as IRQs
  mfd/gpio: Move HTC GPIO driver to GPIO subsystem
  gpio: MAINTAINERS: Add an entry for GPIO mockup driver
  gpio/mockup: add virtual gpio device
  gpio: Added zynq specific check for special pins on bank zero
  gpio: axp209: Implement get_direction
  gpio: aspeed: remove redundant return value check
  gpio: loongson1: remove redundant return value check
  ARM: omap2: fix missing include
  gpio: tc3589x: fix up complaints on unsigned
  gpio: tc3589x: add .get_direction() and small cleanup
  gpio: f7188x: use gpiochip_get_data instead of container_of
  gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
  gpio: aspeed: fix return value check in aspeed_gpio_probe()
  ...

gpio: acpi: separation of concerns

2016-10-03T21:38:10+00:00

The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.

Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.

Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).

For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.

Cc: Rafael J. Wysocki 
Acked-by: Mika Westerberg 
Signed-off-by: Linus Walleij

Merge tag 'v4.8-rc6' into devel

2016-09-23T12:57:16+00:00

Linux 4.8-rc6

pinctrl: sunxi: Remove unsupported PWM channel pinmux in H3

2016-09-07T23:08:23+00:00

H3 has single PWM channel. The second PWM channel is not supported,
so the pinctrl function should be removed.

Signed-off-by: Milo Kim 
Acked-by: Chen-Yu Tsai 
Signed-off-by: Linus Walleij

pinctrl: sunxi: Add GR8 controller support

2016-09-07T19:15:49+00:00

Just like the other member of the sunxi family, let's add a pinctrl table
for the muxing options.

Signed-off-by: Mylène Josserand 
Signed-off-by: Maxime Ripard 
Acked-by: Chen-Yu Tsai 
Signed-off-by: Linus Walleij