soc: Amlogic driver updates for v5.3
- canvas: add support for Meson8*

* tag 'amlogic-drivers' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  soc: amlogic: canvas: add support for Meson8, Meson8b and Meson8m2
  dt-bindings: soc: amlogic: canvas: document support for Meson8/8b/8m2

Signed-off-by: Olof Johansson <olof@lixom.net>

The canvas IP on Meson8, Meson8b and Meson8m2 is mostly identical to the
one on GXBB and newer. The only known difference so far is that that the
"endianness" bits are not supported on Meson8m2 and earlier.

Add new compatible strings and a check in meson_canvas_config() to
validate that the endianness bits cannot be configured on the 32-bit
SoCs.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Amlogic G12A SoC has a very similar VPU Power Controller setup
than the older GXBB, GXL & GXm SoCs.

This patch adds the variant support for G12A.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The register bitmask to power on/off the VPU memories was incorectly set
to 0x2 instead of 0x3. While still working, let's use the recommended
vendor value instead.

Fixes: 75fcb5ca4b46 ("soc: amlogic: add Meson GX VPU Domains driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add an of_node_put when a tested device node is not available.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@

e = f(...);
... when != of_node_put(e)
    when != x = e
    when != e = x
    when any
if (<+...of_device_is_available(e)...+>) {
  ... when != of_node_put(e)
(
  return e;
|
+ of_node_put(e);
  return ...;
)
}
// </smpl>

Fixes: a9daaba2965e8 ("soc: Add Amlogic SoC Information driver")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

This adds the:
- G12A SoC ID and S905X2, S905D2 package IDs, found booting the
  X96 Max and U200 Reference Board
- G12B SoC ID and S922X package ID, found booting the Odroid-N2
- S805X, S805Y package IDs found in the vendor U-Boot source

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

When updated IDs on f842c41adc04 ("amlogic: meson-gx-socinfo: Update soc ids")
we introduced packages ids using the full 8bit value, but in the function
socinfo_to_package_id() the id was filtered with the 0xf0 mask.

While the 0xf0 mask is valid for most board, it filters out the lower
4 bits which encodes some characteristics of the chip.

This patch moves the mask into the meson_gx_package_id table to be applied
on each package name independently and add the correct mask for some
specific entries.

An example is the S905, in the vendor code the S905 is package_id
different from 0x20, and S905M is exactly 0x20.

Another example are the The Wetek Hub & Play2 boards using a S905-H
variant, which is the S905 SoC with some licence bits enabled.
These licence bits are encoded in the lower 4bits, so to detect
the -H variant, we must detect the id == 0x3 with the 0xf mask.

Fixes: f842c41adc04 ("amlogic: meson-gx-socinfo: Update soc ids")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add support for the axg and g12a SoC family in amlogic clk measure

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: squashed some fixups from Martin]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

When probe fails, a platforn_device is still associated to the node,
but dev_get_drvdata() returns NULL.

Handle this case by returning a consistent error.

Fixes: d4983983d987 ("soc: amlogic: add meson-canvas driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
[khilman: fixed minor typo in comment ]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>