linux.git/drivers/thermal, branch v4.19.149

thermal: rcar_thermal: Handle probe error gracefully

2020-10-01T11:14:39+00:00

[ Upstream commit 39056e8a989ef52486e063e34b4822b341e47b0e ]

If the common register memory resource is not available the driver needs
to fail gracefully to disable PM. Instead of returning the error
directly store it in ret and use the already existing error path.

Signed-off-by: Niklas Söderlund 
Reviewed-by: Geert Uytterhoeven 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200310114709.1483860-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin

thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430

2020-09-09T17:04:28+00:00

[ Upstream commit 30d24faba0532d6972df79a1bf060601994b5873 ]

We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:

thermal thermal_zone0: critical temperature reached (143 C), shutting down

Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.

Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.

Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.

Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.

Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Signed-off-by: Tony Lindgren 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
Signed-off-by: Sasha Levin

thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()

2020-08-19T06:14:58+00:00

[ Upstream commit 0f348db01fdf128813fdd659fcc339038fb421a4 ]

This condition is reversed and will cause breakage.

Fixes: 7440f518dad9 ("thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR")
Signed-off-by: Dan Carpenter 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200616091949.GA11940@mwanda
Signed-off-by: Sasha Levin

thermal/drivers/cpufreq_cooling: Fix wrong frequency converted from power

2020-07-22T07:32:12+00:00

commit 371a3bc79c11b707d7a1b7a2c938dc3cc042fffb upstream.

The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
	/* KHz     mW */
	{ 1008000, 36, 0 },
	{ 1200000, 49, 0 },
	{ 1296000, 59, 0 },
	{ 1416000, 72, 0 },
	{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.

Fixes: 349d39dc5739 ("thermal: cpu_cooling: merge frequency and power tables")
Cc:  # v4.13+
Signed-off-by: Finley Xiao 
Acked-by: Viresh Kumar 
Reviewed-by: Amit Kucheria 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com
Signed-off-by: Viresh Kumar 
Signed-off-by: Greg Kroah-Hartman

Revert "thermal: mediatek: fix register index error"

2020-07-22T07:32:05+00:00

[ Upstream commit a8f62f183021be389561570ab5f8c701a5e70298 ]

This reverts commit eb9aecd90d1a39601e91cd08b90d5fee51d321a6

The above patch is supposed to fix a register index error on mt2701. It
is not clear if the problem solved is a hang or just an invalid value
returned, my guess is the second. The patch introduces, though, a new
hang on MT8173 device making them unusable. So, seems reasonable, revert
the patch because introduces a worst issue.

The reason I send a revert instead of trying to fix the issue for MT8173
is because the information needed to fix the issue is in the datasheet
and is not public. So I am not really able to fix it.

Fixes the following bug when CONFIG_MTK_THERMAL is set on MT8173
devices.

[    2.222488] Unable to handle kernel paging request at virtual address ffff8000125f5001
[    2.230421] Mem abort info:
[    2.233207]   ESR = 0x96000021
[    2.236261]   EC = 0x25: DABT (current EL), IL = 32 bits
[    2.241571]   SET = 0, FnV = 0
[    2.244623]   EA = 0, S1PTW = 0
[    2.247762] Data abort info:
[    2.250640]   ISV = 0, ISS = 0x00000021
[    2.254473]   CM = 0, WnR = 0
[    2.257544] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000041850000
[    2.264251] [ffff8000125f5001] pgd=000000013ffff003, pud=000000013fffe003, pmd=000000013fff9003, pte=006800001100b707
[    2.274867] Internal error: Oops: 96000021 [#1] PREEMPT SMP
[    2.280432] Modules linked in:
[    2.283483] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.7.0-rc6+ #162
[    2.289914] Hardware name: Google Elm (DT)
[    2.294003] pstate: 20000005 (nzCv daif -PAN -UAO)
[    2.298792] pc : mtk_read_temp+0xb8/0x1c8
[    2.302793] lr : mtk_read_temp+0x7c/0x1c8
[    2.306794] sp : ffff80001003b930
[    2.310100] x29: ffff80001003b930 x28: 0000000000000000
[    2.315404] x27: 0000000000000002 x26: ffff0000f9550b10
[    2.320709] x25: ffff0000f9550a80 x24: 0000000000000090
[    2.326014] x23: ffff80001003ba24 x22: 00000000610344c0
[    2.331318] x21: 0000000000002710 x20: 00000000000001f4
[    2.336622] x19: 0000000000030d40 x18: ffff800011742ec0
[    2.341926] x17: 0000000000000001 x16: 0000000000000001
[    2.347230] x15: ffffffffffffffff x14: ffffff0000000000
[    2.352535] x13: ffffffffffffffff x12: 0000000000000028
[    2.357839] x11: 0000000000000003 x10: ffff800011295ec8
[    2.363143] x9 : 000000000000291b x8 : 0000000000000002
[    2.368447] x7 : 00000000000000a8 x6 : 0000000000000004
[    2.373751] x5 : 0000000000000000 x4 : ffff800011295cb0
[    2.379055] x3 : 0000000000000002 x2 : ffff8000125f5001
[    2.384359] x1 : 0000000000000001 x0 : ffff0000f9550a80
[    2.389665] Call trace:
[    2.392105]  mtk_read_temp+0xb8/0x1c8
[    2.395760]  of_thermal_get_temp+0x2c/0x40
[    2.399849]  thermal_zone_get_temp+0x78/0x160
[    2.404198]  thermal_zone_device_update.part.0+0x3c/0x1f8
[    2.409589]  thermal_zone_device_update+0x34/0x48
[    2.414286]  of_thermal_set_mode+0x58/0x88
[    2.418375]  thermal_zone_of_sensor_register+0x1a8/0x1d8
[    2.423679]  devm_thermal_zone_of_sensor_register+0x64/0xb0
[    2.429242]  mtk_thermal_probe+0x690/0x7d0
[    2.433333]  platform_drv_probe+0x5c/0xb0
[    2.437335]  really_probe+0xe4/0x448
[    2.440901]  driver_probe_device+0xe8/0x140
[    2.445077]  device_driver_attach+0x7c/0x88
[    2.449252]  __driver_attach+0xac/0x178
[    2.453082]  bus_for_each_dev+0x78/0xc8
[    2.456909]  driver_attach+0x2c/0x38
[    2.460476]  bus_add_driver+0x14c/0x230
[    2.464304]  driver_register+0x6c/0x128
[    2.468131]  __platform_driver_register+0x50/0x60
[    2.472831]  mtk_thermal_driver_init+0x24/0x30
[    2.477268]  do_one_initcall+0x50/0x298
[    2.481098]  kernel_init_freeable+0x1ec/0x264
[    2.485450]  kernel_init+0x1c/0x110
[    2.488931]  ret_from_fork+0x10/0x1c
[    2.492502] Code: f9401081 f9400402 b8a67821 8b010042 (b9400042)
[    2.498599] ---[ end trace e43e3105ed27dc99 ]---
[    2.503367] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    2.511020] SMP: stopping secondary CPUs
[    2.514941] Kernel Offset: disabled
[    2.518421] CPU features: 0x090002,25006005
[    2.522595] Memory Limit: none
[    2.525644] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]--

Cc: Michael Kao 
Fixes: eb9aecd90d1a ("thermal: mediatek: fix register index error")
Signed-off-by: Enric Balletbo i Serra 
Reviewed-by: Matthias Brugger 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200707103412.1010823-1-enric.balletbo@collabora.com
Signed-off-by: Sasha Levin

thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR

2020-06-25T13:32:54+00:00

[ Upstream commit 7440f518dad9d861d76c64956641eeddd3586f75 ]

On error the function ti_bandgap_get_sensor_data() returns the error
code in ERR_PTR() but we only checked if the return value is NULL or
not. And, so we can dereference an error code inside ERR_PTR.
While at it, convert a check to IS_ERR_OR_NULL.

Signed-off-by: Sudip Mukherjee 
Reviewed-by: Amit Kucheria 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200424161944.6044-1-sudipm.mukherjee@gmail.com
Signed-off-by: Sasha Levin

thermal: brcmstb_thermal: Do not use DT coefficients

2020-03-05T15:42:22+00:00

commit e1ff6fc22f19e2af8adbad618526b80067911d40 upstream.

At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.

The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.

We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.

Fixes: 9e03cf1b2dd5 ("thermal: add brcmstb AVS TMON driver")
Signed-off-by: Florian Fainelli 
Reviewed-by: Amit Kucheria 
Signed-off-by: Daniel Lezcano 
Link: https://lore.kernel.org/r/20200114190607.29339-2-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman

thermal: cpu_cooling: Actually trace CPU load in thermal_power_cpu_get_power

2020-01-27T13:50:48+00:00

[ Upstream commit bf45ac18b78038e43af3c1a273cae4ab5704d2ce ]

The CPU load values passed to the thermal_power_cpu_get_power
tracepoint are zero for all CPUs, unless, unless the
thermal_power_cpu_limit tracepoint is enabled too:

  irq/41-rockchip-98    [000] ....   290.972410: thermal_power_cpu_get_power:
  cpus=0000000f freq=1800000 load={{0x0,0x0,0x0,0x0}} dynamic_power=4815

vs

  irq/41-rockchip-96    [000] ....    95.773585: thermal_power_cpu_get_power:
  cpus=0000000f freq=1800000 load={{0x56,0x64,0x64,0x5e}} dynamic_power=4959
  irq/41-rockchip-96    [000] ....    95.773596: thermal_power_cpu_limit:
  cpus=0000000f freq=408000 cdev_state=10 power=416

There seems to be no good reason for omitting the CPU load information
depending on another tracepoint. My guess is that the intention was to
check whether thermal_power_cpu_get_power is (still) enabled, however
'load_cpu != NULL' already indicates that it was at least enabled when
cpufreq_get_requested_power() was entered, there seems little gain
from omitting the assignment if the tracepoint was just disabled, so
just remove the check.

Fixes: 6828a4711f99 ("thermal: add trace events to the power allocator governor")
Signed-off-by: Matthias Kaehlcke 
Reviewed-by: Daniel Lezcano 
Acked-by: Javi Merino 
Acked-by: Viresh Kumar 
Signed-off-by: Eduardo Valentin 
Signed-off-by: Sasha Levin

thermal: rcar_gen3_thermal: fix interrupt type

2020-01-27T13:50:48+00:00

[ Upstream commit 2c0928c9e004589dc9e7672c40a38d6c4ca12701 ]

Currently IRQF_SHARED type interrupt line is allocated, but it
is not appropriate, as the interrupt line isn't shared between
different devices, instead IRQF_ONESHOT is the proper type.

By changing interrupt type to IRQF_ONESHOT, now irq handler is
no longer needed, as clear of interrupt status can be done in
threaded interrupt context.

Because IRQF_ONESHOT type interrupt line is kept disabled until
the threaded handler has been run, so there is no need to protect
read/write of REG_GEN3_IRQSTR with lock.

Fixes: 7d4b269776ec6 ("enable hardware interrupts for trip points")
Signed-off-by: Jiada Wang 
Reviewed-by: Simon Horman 
Tested-by: Simon Horman 
Reviewed-by: Daniel Lezcano 
Signed-off-by: Eduardo Valentin 
Signed-off-by: Sasha Levin

thermal: mediatek: fix register index error

2020-01-27T13:50:19+00:00

[ Upstream commit eb9aecd90d1a39601e91cd08b90d5fee51d321a6 ]

The index of msr and adcpnp should match the sensor
which belongs to the selected bank in the for loop.

Fixes: b7cf0053738c ("thermal: Add Mediatek thermal driver for mt2701.")
Signed-off-by: Michael Kao 
Signed-off-by: Eduardo Valentin 
Signed-off-by: Sasha Levin