linux.git/drivers/tty, branch v4.19.205

serial: 8250: Mask out floating 16/32-bit bus bits

2021-08-12T11:19:43+00:00

commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.

Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.

The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase.  For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:

YAMON> dump -32 0xbf000900 0x40

BF000900: 1F000942 1F000942 1F000900 1F000900  ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900  ................
BF000920: 1F000900 1F000900 1F000960 1F000960  ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF  ................

YAMON>

Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.

Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.

Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected.  Fix the same issue in `serial_dl_read'.

The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: 
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:

+	case UPIO_MEM32:
+		return readl(up->port.membase + offset);
+

which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for.  It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé 
Signed-off-by: Maciej W. Rozycki 
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman

tty: serial: 8250: serial_cs: Fix a memory leak in error handling path

2021-07-20T14:16:08+00:00

[ Upstream commit fad92b11047a748c996ebd6cfb164a63814eeb2e ]

In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.

Add a resource handling path to free this memory.

Signed-off-by: Christophe JAILLET 
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: serial: fsl_lpuart: fix the potential risk of division or modulo by zero

2021-07-20T14:16:07+00:00

[ Upstream commit fcb10ee27fb91b25b68d7745db9817ecea9f1038 ]

We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.

Signed-off-by: Sherry Sun 
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: mvebu-uart: fix calculation of clock divisor

2021-07-20T14:16:03+00:00

commit 9078204ca5c33ba20443a8623a41a68a9995a70d upstream.

The clock divisor should be rounded to the closest value.

Signed-off-by: Pali Rohár 
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Cc: stable@vger.kernel.org # 0e4cf69ede87 ("serial: mvebu-uart: clarify the baud rate derivation")
Link: https://lore.kernel.org/r/20210624224909.6350-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman

serial: mvebu-uart: clarify the baud rate derivation

2021-07-20T14:16:03+00:00

commit 0e4cf69ede8751d25f733cd7a6f954c5b505fa03 upstream.

The current comment in ->set_baud_rate() is rather incomplete as it
fails to describe what are the actual stages for the baudrate
derivation. Replace this comment with something more explicit and
close to the functional specification. Also adapt the variable names
to it.

Signed-off-by: Miquel Raynal 
Signed-off-by: Greg Kroah-Hartman

serial: mvebu-uart: correctly calculate minimal possible baudrate

2021-07-20T14:15:58+00:00

[ Upstream commit deeaf963569a0d9d1b08babb771f61bb501a5704 ]

For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.

Signed-off-by: Pali Rohár 
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial: 8250: Actually allow UPF_MAGIC_MULTIPLIER baud rates

2021-07-20T14:15:56+00:00

[ Upstream commit 78bcae8616ac277d6cb7f38e211493948ed73e30 ]

Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: .

Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them.  This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.

Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set.  Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.

References:

[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
    Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
    03/27/2000, Table 31 - "Baud Rates", p. 77

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki 
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: nozomi: Fix the error handling path of 'nozomi_card_init()'

2021-07-20T14:15:55+00:00

[ Upstream commit 6ae7d0f5a92b9619f6e3c307ce56b2cefff3f0e9 ]

The error handling path is broken and we may un-register things that have
never been registered.

Update the loops index accordingly.

Fixes: 9842c38e9176 ("kfifo: fix warn_unused_result")
Suggested-by: Dan Carpenter 
Signed-off-by: Christophe JAILLET 
Link: https://lore.kernel.org/r/e28c2e92c7475da25b03d022ea2d6dcf1ba807a2.1621968629.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

tty: nozomi: Fix a resource leak in an error handling function

2021-07-20T14:15:53+00:00

[ Upstream commit 31a9a318255960d32ae183e95d0999daf2418608 ]

A 'request_irq()' call is not balanced by a corresponding 'free_irq()' in
the error handling path, as already done in the remove function.

Add it.

Fixes: 9842c38e9176 ("kfifo: fix warn_unused_result")
Reviewed-by: Jiri Slaby 
Signed-off-by: Christophe JAILLET 
Link: https://lore.kernel.org/r/4f0d2b3038e82f081d370ccb0cade3ad88463fe7.1620580838.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Sasha Levin

serial_cs: remove wrong GLOBETROTTER.cis entry

2021-07-20T14:15:41+00:00

commit 11b1d881a90fc184cc7d06e9804eb288c24a2a0d upstream.

The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.

Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0

result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2

The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"

Signed-off-by: Ondrej Zary 
Cc: stable 
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman