linux.git/drivers/usb, branch v5.13.1

usb: core: hub: Disable autosuspend for Cypress CY7C65632

2021-06-17T13:34:21+00:00

The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.

Disabling autosuspend for this hub resolves the issue.

Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn 
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus

2021-06-16T07:33:39+00:00

Peter writes:

One bug fix for USB charger detection at imx7d and imx8m series SoCs

* tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection

usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection

2021-06-16T01:04:22+00:00

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.

During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.

During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).

Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.

VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.

Cc: 
Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima 
Signed-off-by: Jun Li 
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen

usb: dwc3: core: fix kernel panic when do reboot

2021-06-15T10:20:26+00:00

When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.

[ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002
....
[ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 2925.037005] pc : inode_permission+0x2c/0x198
[ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8
[ 2925.045903] sp : ffff80001276ba70
[ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000
[ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100
[ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001
[ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000
[ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004
[ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030
[ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420
[ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080
[ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065
[ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188
[ 2925.120671] Call trace:
[ 2925.123119]  inode_permission+0x2c/0x198
[ 2925.127042]  lookup_one_len_common+0xb0/0xf8
[ 2925.131315]  lookup_one_len_unlocked+0x34/0xb0
[ 2925.135764]  lookup_positive_unlocked+0x14/0x50
[ 2925.140296]  debugfs_lookup+0x68/0xa0
[ 2925.143964]  dwc3_gadget_free_endpoints+0x84/0xb0
[ 2925.148675]  dwc3_gadget_exit+0x28/0x78
[ 2925.152518]  dwc3_drd_exit+0x100/0x1f8
[ 2925.156267]  dwc3_remove+0x11c/0x120
[ 2925.159851]  dwc3_shutdown+0x14/0x20
[ 2925.163432]  platform_shutdown+0x28/0x38
[ 2925.167360]  device_shutdown+0x15c/0x378
[ 2925.171291]  kernel_restart_prepare+0x3c/0x48
[ 2925.175650]  kernel_restart+0x1c/0x68
[ 2925.179316]  __do_sys_reboot+0x218/0x240
[ 2925.183247]  __arm64_sys_reboot+0x28/0x30
[ 2925.187262]  invoke_syscall+0x48/0x100
[ 2925.191017]  el0_svc_common.constprop.0+0x48/0xc8
[ 2925.195726]  do_el0_svc+0x28/0x88
[ 2925.199045]  el0_svc+0x20/0x30
[ 2925.202104]  el0_sync_handler+0xa8/0xb0
[ 2925.205942]  el0_sync+0x148/0x180
[ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660)
[ 2925.215372] ---[ end trace 124254d8e485a58b ]---
[ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 2925.227676] Kernel Offset: disabled
[ 2925.231164] CPU features: 0x00001001,20000846
[ 2925.235521] Memory Limit: none
[ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---

Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: Jack Pham 
Tested-by: Jack Pham 
Signed-off-by: Peter Chen 
Link: https://lore.kernel.org/r/20210608105656.10795-1-peter.chen@kernel.org
(cherry picked from commit 2a042767814bd0edf2619f06fecd374e266ea068)
Link: https://lore.kernel.org/r/20210615080847.GA10432@jackp-linux.qualcomm.com
Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

2021-06-11T10:32:49+00:00

Johan writes:

USB-serial fixes for 5.13-rc6

Here are two fixes for the cp210x driver. The first fixes a regression
with early revisions of the CP2102N which specifically broke some ESP32
development boards. The second makes sure that the pin configuration is
detected properly also for the CP2102N QFN20 package.

Both have been in linux-next over night and with no reported issues.

* tag 'usb-serial-5.13-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: cp210x: fix CP2102N-A01 modem control
  USB: serial: cp210x: fix alternate function for CP2102N QFN20

Revert "usb: gadget: fsl: Re-enable driver for ARM SoCs"

2021-06-11T07:18:47+00:00

This reverts commit e0e8b6abe8c862229ba00cdd806e8598cdef00bb.

Turns out this breaks the build.  We had numerous reports of problems
from linux-next and 0-day about this not working properly, so revert it
for now until it can be figured out properly.

The build errors are:
	arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x29d4): undefined reference to `fsl_udc_clk_finalize'
	arm-linux-gnueabi-ld: fsl_udc_core.c:(.text+0x2ba8): undefined reference to `fsl_udc_clk_release'
	fsl_udc_core.c:(.text+0x2848): undefined reference to `fsl_udc_clk_init'
	fsl_udc_core.c:(.text+0xe88): undefined reference to `fsl_udc_clk_release'

Reported-by: Stephen Rothwell 
Reported-by: kernel test robot 
Fixes: e0e8b6abe8c8 ("usb: gadget: fsl: Re-enable driver for ARM SoCs")
Cc: stable 
Cc: Joel Stanley 
Cc: Leo Li 
Cc: Peter Chen 
Cc: Arnd Bergmann 
Cc: Felipe Balbi 
Cc: Shawn Guo 
Cc: Ran Wang 
Signed-off-by: Greg Kroah-Hartman

usb: typec: mux: Fix copy-paste mistake in typec_mux_match

2021-06-10T18:03:06+00:00

Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.

The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.

Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus 
Signed-off-by: Bjorn Andersson 
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman

usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path

2021-06-10T18:02:54+00:00

If ucsi_init() fails for some reason (e.g. ucsi_register_port()
fails or general communication failure to the PPM), particularly at
any point after the GET_CAPABILITY command had been issued, this
results in unwinding the initialization and returning an error.
However the ucsi structure's ucsi_capability member retains its
current value, including likely a non-zero num_connectors.
And because ucsi_init() itself is done in a workqueue a UCSI
interface driver will be unaware that it failed and may think the
ucsi_register() call was completely successful.  Later, if
ucsi_unregister() is called, due to this stale ucsi->cap value it
would try to access the items in the ucsi->connector array which
might not be in a proper state or not even allocated at all and
results in NULL or invalid pointer dereference.

Fix this by clearing the ucsi->cap value to 0 during the error
path of ucsi_init() in order to prevent a later ucsi_unregister()
from entering the connector cleanup loop.

Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus 
Signed-off-by: Mayank Rana 
Signed-off-by: Jack Pham 
Link: https://lore.kernel.org/r/20210609073535.5094-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman

usb: gadget: fsl: Re-enable driver for ARM SoCs

2021-06-10T18:02:16+00:00

The commit a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
dropped the ARCH_MXC dependency from USB_FSL_USB2, leaving it depending
solely on FSL_SOC.

FSL_SOC is powerpc only; it was briefly available on ARM in 2014 but was
removed by commit cfd074ad8600 ("ARM: imx: temporarily remove
CONFIG_SOC_FSL from LS1021A"). Therefore the driver can no longer be
enabled on ARM platforms.

This appears to be a mistake as arm64's ARCH_LAYERSCAPE and arm32
SOC_LS1021A SoCs use this symbol. It's enabled in these defconfigs:

arch/arm/configs/imx_v6_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/arm/configs/multi_v7_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mgcoge_defconfig:CONFIG_USB_FSL_USB2=y
arch/powerpc/configs/mpc512x_defconfig:CONFIG_USB_FSL_USB2=y

To fix, expand the dependencies so USB_FSL_USB2 can be enabled on the
ARM platforms, and with COMPILE_TEST.

Fixes: a390bef7db1f ("usb: gadget: fsl_mxc_udc: Remove the driver")
Signed-off-by: Joel Stanley 
Link: https://lore.kernel.org/r/20210610034957.93376-1-joel@jms.id.au
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: typec: wcove: Use LE to CPU conversion when accessing msg->header

2021-06-10T18:01:23+00:00

As LKP noticed the Sparse is not happy about strict type handling:
   .../typec/tcpm/wcove.c:380:50: sparse:     expected unsigned short [usertype] header
   .../typec/tcpm/wcove.c:380:50: sparse:     got restricted __le16 const [usertype] header

Fix this by switching to use pd_header_cnt_le() instead of pd_header_cnt()
in the affected code.

Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Fixes: 3c4fb9f16921 ("usb: typec: wcove: start using tcpm for USB PD support")
Reported-by: kernel test robot 
Reviewed-by: Heikki Krogerus 
Reviewed-by: Guenter Roeck 
Signed-off-by: Andy Shevchenko 
Link: https://lore.kernel.org/r/20210609172202.83377-1-andriy.shevchenko@linux.intel.com
Cc: stable 
Signed-off-by: Greg Kroah-Hartman