linux.git/drivers/w1, branch v5.11-rc1

w1: w1_therm: Rename conflicting sysfs attribute 'eeprom' to 'eeprom_cmd'

2020-11-12T07:50:13+00:00

Duplicate attribute 'eeprom' is defined in:
1) Documentation/ABI/testing/sysfs-driver-w1_therm
2) Documentation/ABI/stable/sysfs-driver-w1_ds28e04

Both drivers define an attribute: /sys/bus/w1/devices/.../eeprom
with conflicting behavior.

Fix by renaming the newer one in w1_therm.c to 'eeprom_cmd'.

Reported-by: Mauro Carvalho Chehab 
Suggested-by: Greg Kroah-Hartman 
Link: https://lore.kernel.org/lkml/20201029152845.6bbb39ce@coco.lan/
Signed-off-by: Ivan Zaentsev 
Link: https://lore.kernel.org/r/20201112064931.8471-1-ivan.zaentsev@wirenboard.ru
Signed-off-by: Greg Kroah-Hartman

w1: w1_therm: make w1_poll_completion static

2020-10-05T12:49:24+00:00

kernel test robot rightly points out that w1_poll_completion() should be
static, so mark it as such.

Cc: Ivan Zaentsev 
Reported-by: kernel test robot 
Link: https://lore.kernel.org/r/20201005123703.GA800532@kroah.com
Signed-off-by: Greg Kroah-Hartman

w1: Constify static w1_family_ops structs

2020-10-05T11:21:49+00:00

The only usage of these structs is to assign their address to the fops
field in the w1_family struct, which is a const pointer. Make them const
to allow the compiler to put them in read-only memory.

This was done with the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):

// 
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct w1_family_ops i@p = {...};

@ok1@
identifier r1.i;
position p;
identifier s;
@@
static struct w1_family s = {
	.fops=&i@p,
};

@bad1@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p

@depends on !bad1 disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct w1_family_ops i={};
// 

Signed-off-by: Rikard Falkeborn 
Link: https://lore.kernel.org/r/20201004193202.4044-3-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman

w1: Constify struct w1_family_ops

2020-10-05T11:21:49+00:00

The fops field in the w1_family struct is never modified. Make it const
to indicate that. Constifying the pointer makes it possible for drivers
to declare static w1_family_ops structs const, which in turn will allow
the compiler to put it in read-only memory.

Reviewed-by: Sebastian Reichel 
Signed-off-by: Rikard Falkeborn 
Link: https://lore.kernel.org/r/20201004193202.4044-2-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman

w1: mxc_w1: Fix timeout resolution problem leading to bus error

2020-10-02T13:53:25+00:00

On my platform (i.MX53) bus access sometimes fails with
	w1_search: max_slave_count 64 reached, will continue next search.

The reason is the use of jiffies to implement a 200us timeout in
mxc_w1_ds2_touch_bit().
On some platforms the jiffies timer resolution is insufficient for this.

Fix by replacing jiffies by ktime_get().

For consistency apply the same change to the other use of jiffies in
mxc_w1_ds2_reset_bus().

Fixes: f80b2581a706 ("w1: mxc_w1: Optimize mxc_w1_ds2_touch_bit()")
Cc: stable 
Signed-off-by: Martin Fuzzey 
Link: https://lore.kernel.org/r/1601455030-6607-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman

w1: w1_therm: Add support for GXCAS GX20MH01 device.

2020-10-02T09:49:54+00:00

GX20MH01 device shares family number 0x28 with DS18B20. The device
is generally compatible with DS18B20. Added are the lowest 2^-5, 2^-6
temperature bits in Config register; R2 bit in Config register
enabling 13 and 14 bit resolutions. It is powered up in 14 bit mode.

Signed-off-by: Ivan Zaentsev 
Link: https://lore.kernel.org/r/20200904160004.87710-2-ivan.zaentsev@wirenboard.ru
Acked-by: Evgeniy Polyakov 
Signed-off-by: Greg Kroah-Hartman

w1: w1_therm: Add sysfs entries to control conversion time and driver features

2020-10-02T09:49:50+00:00

The conversion time of common DS18B20 clones deviates from
datasheet specs. Allow adjustment and automatic measure of the
conversion time.

Add 'conv_time' sysfs attribute:
  *read*: Current conversion time in milliseconds.
  *write*:
     '0': Set default conversion time.
     '1': Measure and set the conversion time. Make a
          single temperature conversion, poll and measure
          an actual value. Measured value is increased
          by 20% for temperature drift. A new conversion
          time is returned by reading the same attribute.
     other positive value:
        Set the conversion time in milliseconds.

The setting is active until a resolution change. Then it is reset to
default conversion time for a new resolution.

Add 'features' sysfs attribute to control optional driver settings
per device. Bit masks to read/write (logical OR):
  1: Enable check for conversion success. If byte 6 of
     scratchpad memory is 0xC after conversion, and
     temperature reads 85.00 (powerup value) or 127.94
     (insufficient power) - return a conversion error.

  2: Enable poll for conversion completion. Generate read cycles
     after the conversion start and wait for 1's. In parasite
     power mode this feature is not available.

There are some clones of DS18B20 with fixed 12 bit resolution. Make the
driver verify the resolution by reading back the device after resolution
change.

Signed-off-by: Ivan Zaentsev 
Acked-by: Evgeniy Polyakov 
Link: https://lore.kernel.org/r/20200904160004.87710-1-ivan.zaentsev@wirenboard.ru
Signed-off-by: Greg Kroah-Hartman

w1: Replace zero-length array with flexible-array

2020-06-16T04:08:32+00:00

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva

treewide: replace '---help---' in Kconfig files with 'help'

2020-06-13T16:57:21+00:00

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

  a) 4 spaces + '---help---'
  b) 7 spaces + '---help---'
  c) 8 spaces + '---help---'
  d) 1 space + 1 tab + '---help---'
  e) 1 tab + '---help---'    (correct indentation)
  f) 1 tab + 1 space + '---help---'
  g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

  $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'

Signed-off-by: Masahiro Yamada

w1: omap-hdq: print dev_err if irq flags are not cleared

2020-05-27T10:18:49+00:00

If irq flags are not cleared for certain operations we
print an error message.

Since this should never occur in normal operation, this
patch is an optional safety-net and debugging tool.

Signed-off-by: H. Nikolaus Schaller 
Link: https://lore.kernel.org/r/2de305d3046c7281a7123347899abbaa64c54fb8.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman