linux.git/net/hsr, branch v6.10-rc6

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2024-05-09T17:01:01+00:00

Cross-merge networking fixes after downstream PR.

No conflicts.

Adjacent changes:

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
  35d92abfbad8 ("net: hns3: fix kernel crash when devlink reload during initialization")
  2a1a1a7b5fd7 ("net: hns3: add command queue trace for hns3")

Signed-off-by: Jakub Kicinski

hsr: Simplify code for announcing HSR nodes timer setup

2024-05-09T01:56:30+00:00

Up till now the code to start HSR announce timer, which triggers sending
supervisory frames, was assuming that hsr_netdev_notify() would be called
at least twice for hsrX interface. This was required to have different
values for old and current values of network device's operstate.

This is problematic for a case where hsrX interface is already in the
operational state when hsr_netdev_notify() is called, so timer is not
configured to trigger and as a result the hsrX is not sending supervisory
frames to HSR ring.

This error has been discovered when hsr_ping.sh script was run. To be
more specific - for the hsr1 and hsr2 the hsr_netdev_notify() was
called at least twice with different IF_OPER_{LOWERDOWN|DOWN|UP} states
assigned in hsr_check_carrier_and_operstate(hsr). As a result there was
no issue with sending supervisory frames.
However, with hsr3, the notify function was called only once with
operstate set to IF_OPER_UP and timer responsible for triggering
supervisory frames was not fired.

The solution is to use netif_oper_up() and netif_running() helper
functions to assess if network hsrX device is up.
Only then, when the timer is not already pending, it is started.
Otherwise it is deactivated.

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Lukasz Majewski 
Reviewed-by: Simon Horman 
Link: https://lore.kernel.org/r/20240507111214.3519800-1-lukma@denx.de
Signed-off-by: Jakub Kicinski

net: annotate writes on dev->mtu from ndo_change_mtu()

2024-05-07T23:19:14+00:00

Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c94510 ("inet: protect against too small
mtu values.")

We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.

It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()

Signed-off-by: Eric Dumazet 
Reported-by: Simon Horman 
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller 
Reviewed-by: Sabrina Dubroca 
Reviewed-by: Simon Horman 
Acked-by: Shannon Nelson 
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski

net: hsr: init prune_proxy_timer sooner

2024-04-30T02:02:53+00:00

We must initialize prune_proxy_timer before we attempt
a del_timer_sync() on it.

syzbot reported the following splat:

INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 1 PID: 11 Comm: kworker/u8:1 Not tainted 6.9.0-rc5-syzkaller-01199-gfc48de77d69d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Workqueue: netns cleanup_net
Call Trace:
 
  __dump_stack lib/dump_stack.c:88 [inline]
  dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
  assign_lock_key+0x238/0x270 kernel/locking/lockdep.c:976
  register_lock_class+0x1cf/0x980 kernel/locking/lockdep.c:1289
  __lock_acquire+0xda/0x1fd0 kernel/locking/lockdep.c:5014
  lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
  __timer_delete_sync+0x148/0x310 kernel/time/timer.c:1648
  del_timer_sync include/linux/timer.h:185 [inline]
  hsr_dellink+0x33/0x80 net/hsr/hsr_netlink.c:132
  default_device_exit_batch+0x956/0xa90 net/core/dev.c:11737
  ops_exit_list net/core/net_namespace.c:175 [inline]
  cleanup_net+0x89d/0xcc0 net/core/net_namespace.c:637
  process_one_work kernel/workqueue.c:3254 [inline]
  process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335
  worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
  kthread+0x2f0/0x390 kernel/kthread.c:388
  ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
  ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
 
ODEBUG: assert_init not available (active state 0) object: ffff88806d3fcd88 object type: timer_list hint: 0x0
 WARNING: CPU: 1 PID: 11 at lib/debugobjects.c:517 debug_print_object+0x17a/0x1f0 lib/debugobjects.c:514

Fixes: 5055cccfc2d1 ("net: hsr: Provide RedBox support (HSR-SAN)")
Reported-by: syzbot 
Signed-off-by: Eric Dumazet 
Cc: Lukasz Majewski 
Reviewed-by: Simon Horman 
Link: https://lore.kernel.org/r/20240426163355.2613767-1-edumazet@google.com
Signed-off-by: Jakub Kicinski

net: hsr: Provide RedBox support (HSR-SAN)

2024-04-26T10:04:43+00:00

Introduce RedBox support (HSR-SAN to be more precise) for HSR networks.
Following traffic reduction optimizations have been implemented:
- Do not send HSR supervisory frames to Port C (interlink)
- Do not forward to HSR ring frames addressed to Port C
- Do not forward to Port C frames from HSR ring
- Do not send duplicate HSR frame to HSR ring when destination is Port C

The corresponding patch to modify iptable2 sources has already been sent:
https://lore.kernel.org/netdev/20240308145729.490863-1-lukma@denx.de/T/

Testing procedure (veth and netns):
-----------------------------------
One shall run:
linux-vanila/tools/testing/selftests/net/hsr/hsr_redbox.sh
(Detailed description of the setup one can find in the test
script file).

Testing procedure (real hardware):
----------------------------------
The EVB-KSZ9477 has been used for testing on net-next branch
(SHA1: 5fc68320c1fb3c7d456ddcae0b4757326a043e6f).

Ports 4/5 were used for SW managed HSR (hsr1) as first hsr0 for ports 1/2
(with HW offloading for ksz9477) was created. Port 3 has been used as
interlink port (single USB-ETH dongle).

Configuration - RedBox (EVB-KSZ9477):
if link set lan1 down;ip link set lan2 down
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 supervision 45 version 1
ip link add name hsr1 type hsr slave1 lan4 slave2 lan5 interlink lan3 supervision 45 version 1
ip link set lan4 up;ip link set lan5 up
ip link set lan3 up
ip addr add 192.168.0.11/24 dev hsr1
ip link set hsr1 up

Configuration - DAN-H (EVB-KSZ9477):

ip link set lan1 down;ip link set lan2 down
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 supervision 45 version 1
ip link add name hsr1 type hsr slave1 lan4 slave2 lan5 supervision 45 version 1
ip link set lan4 up;ip link set lan5 up
ip addr add 192.168.0.12/24 dev hsr1
ip link set hsr1 up

This approach uses only SW based HSR devices (hsr1).

--------------          -----------------       ------------
DAN-H  Port5 | <------> | Port5         |       |
       Port4 | <------> | Port4   Port3 | <---> | PC
             |          | (RedBox)      |       | (USB-ETH)
EVB-KSZ9477  |          | EVB-KSZ9477   |       |
--------------          -----------------       ------------

Signed-off-by: Lukasz Majewski 
Signed-off-by: Paolo Abeni

net: hsr: Use full string description when opening HSR network device

2024-03-29T10:42:21+00:00

Up till now only single character ('A' or 'B') was used to provide
information of HSR slave network device status.

As it is also possible and valid, that Interlink network device may
be supported as well, the description must be more verbose. As a result
the full string description is now used.

Signed-off-by: Lukasz Majewski 
Reviewed-by: Andrew Lunn 
Signed-off-by: David S. Miller

net: hsr: hsr_slave: Fix the promiscuous mode in offload mode

2024-03-26T02:51:56+00:00

commit e748d0fd66ab ("net: hsr: Disable promiscuous mode in
offload mode") disables promiscuous mode of slave devices
while creating an HSR interface. But while deleting the
HSR interface, it does not take care of it. It decreases the
promiscuous mode count, which eventually enables promiscuous
mode on the slave devices when creating HSR interface again.

Fix this by not decrementing the promiscuous mode count while
deleting the HSR interface when offload is enabled.

Fixes: e748d0fd66ab ("net: hsr: Disable promiscuous mode in offload mode")
Signed-off-by: Ravi Gunasekaran 
Reviewed-by: Jiri Pirko 
Link: https://lore.kernel.org/r/20240322100447.27615-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski

hsr: Handle failures in module init

2024-03-19T12:38:17+00:00

A failure during registration of the netdev notifier was not handled at
all. A failure during netlink initialization did not unregister the netdev
notifier.

Handle failures of netdev notifier registration and netlink initialization.
Both functions should only return negative values on failure and thereby
lead to the hsr module not being loaded.

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Felix Maurer 
Reviewed-by: Shigeru Yoshida 
Reviewed-by: Breno Leitao 
Link: https://lore.kernel.org/r/3ce097c15e3f7ace98fc7fd9bcbf299f092e63d1.1710504184.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni

hsr: Fix uninit-value access in hsr_get_node()

2024-03-14T12:02:51+00:00

KMSAN reported the following uninit-value access issue [1]:

=====================================================
BUG: KMSAN: uninit-value in hsr_get_node+0xa2e/0xa40 net/hsr/hsr_framereg.c:246
 hsr_get_node+0xa2e/0xa40 net/hsr/hsr_framereg.c:246
 fill_frame_info net/hsr/hsr_forward.c:577 [inline]
 hsr_forward_skb+0xe12/0x30e0 net/hsr/hsr_forward.c:615
 hsr_dev_xmit+0x1a1/0x270 net/hsr/hsr_device.c:223
 __netdev_start_xmit include/linux/netdevice.h:4940 [inline]
 netdev_start_xmit include/linux/netdevice.h:4954 [inline]
 xmit_one net/core/dev.c:3548 [inline]
 dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3564
 __dev_queue_xmit+0x33b8/0x5130 net/core/dev.c:4349
 dev_queue_xmit include/linux/netdevice.h:3134 [inline]
 packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
 packet_snd net/packet/af_packet.c:3087 [inline]
 packet_sendmsg+0x8b1d/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 __sys_sendto+0x735/0xa10 net/socket.c:2191
 __do_sys_sendto net/socket.c:2203 [inline]
 __se_sys_sendto net/socket.c:2199 [inline]
 __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

Uninit was created at:
 slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768
 slab_alloc_node mm/slub.c:3478 [inline]
 kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523
 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560
 __alloc_skb+0x318/0x740 net/core/skbuff.c:651
 alloc_skb include/linux/skbuff.h:1286 [inline]
 alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334
 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2787
 packet_alloc_skb net/packet/af_packet.c:2936 [inline]
 packet_snd net/packet/af_packet.c:3030 [inline]
 packet_sendmsg+0x70e8/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 __sys_sendto+0x735/0xa10 net/socket.c:2191
 __do_sys_sendto net/socket.c:2203 [inline]
 __se_sys_sendto net/socket.c:2199 [inline]
 __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

CPU: 1 PID: 5033 Comm: syz-executor334 Not tainted 6.7.0-syzkaller-00562-g9f8413c4a66f #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023
=====================================================

If the packet type ID field in the Ethernet header is either ETH_P_PRP or
ETH_P_HSR, but it is not followed by an HSR tag, hsr_get_skb_sequence_nr()
reads an invalid value as a sequence number. This causes the above issue.

This patch fixes the issue by returning NULL if the Ethernet header is not
followed by an HSR tag.

Fixes: f266a683a480 ("net/hsr: Better frame dispatch")
Reported-and-tested-by: syzbot+2ef3a8ce8e91b5a50098@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2ef3a8ce8e91b5a50098 [1]
Signed-off-by: Shigeru Yoshida 
Link: https://lore.kernel.org/r/20240312152719.724530-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2024-02-29T22:24:56+00:00

Cross-merge networking fixes after downstream PR.

Conflicts:

net/mptcp/protocol.c
  adf1bb78dab5 ("mptcp: fix snd_wnd initialization for passive socket")
  9426ce476a70 ("mptcp: annotate lockless access for RX path fields")
https://lore.kernel.org/all/20240228103048.19255709@canb.auug.org.au/

Adjacent changes:

drivers/dpll/dpll_core.c
  0d60d8df6f49 ("dpll: rely on rcu for netdev_dpll_pin()")
  e7f8df0e81bf ("dpll: move xa_erase() call in to match dpll_pin_alloc() error path order")

drivers/net/veth.c
  1ce7d306ea63 ("veth: try harder when allocating queue memory")
  0bef512012b1 ("net: add netdev_lockdep_set_classes() to virtual drivers")

drivers/net/wireless/intel/iwlwifi/mvm/d3.c
  8c9bef26e98b ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
  78f65fbf421a ("wifi: iwlwifi: mvm: ensure offloading TID queue exists")

net/wireless/nl80211.c
  f78c1375339a ("wifi: nl80211: reject iftype change with mesh ID change")
  414532d8aa89 ("wifi: cfg80211: use IEEE80211_MAX_MESH_ID_LEN appropriately")

Signed-off-by: Jakub Kicinski