Signed-off-by: Len Brown <len.brown@intel.com>

On a Skylake with 1500MHz base frequency,
the TSC runs at 1512MHz.

This is because the TSC is no longer in the n*100 MHz BCLK domain,
but is now in the m*24MHz crystal clock domain. (24 MHz * 63 = 1512 MHz)

This adds error to several calculations in turbostat,
unless the TSC sample sizes are adjusted for this difference.

Note that calculations in the time domain are immune
from this issue, as the timing sub-system has already
calibrated the TSC against a known wall clock.

AVG_MHz = APERF_delta/measurement_interval

	need no adjustment.  APERF_delta is in the BCLK domain,
	and measurement_interval is in the time domain.

TSC_MHz  =  TSC_delta/measurement_interval

	needs no adjustment -- as we really do want to report
	the actual measured TSC delta here, and measurement_interval
	is in the accurate time domain.

%Busy = MPERF_delta/TSC_delta

	needs adjustment to use TSC_BCLK_DOMAIN_delta.
	TSC_BCLK_DOMAIN_delta = TSC_delta * base_hz / tsc_hz

Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval

	need adjustment as above.

No other metrics in turbostat need to be adjusted.

Before:

     CPU Avg_MHz   %Busy Bzy_MHz TSC_MHz
       -     550   24.84    2216    1512
       0    2191   98.73    2219    1514
       2       0    0.01    2130    1512
       1       9    0.43    2016    1512
       3       2    0.08    2016    1512

After:

     CPU Avg_MHz   %Busy Bzy_MHz TSC_MHz
       -     550   25.05    2198    1512
       0    2190   99.62    2199    1512
       2       0    0.01    2152    1512
       1       9    0.46    2000    1512
       3       2    0.10    2000    1512

Note that in this example, the "Before" Bzy_MHz
was reported as exceeding the 2200 max turbo rate.
Also, even a pinned spin loop would not be reported
as over 99% busy.

Signed-off-by: Len Brown <len.brown@intel.com>

KNL increments APERF and MPERF every 1024 clocks.
This is compliant with the architecture specification,
which requires that only the ratio of APERF/MPERF need be valid.

However, turbostat takes advantage of the fact that these
two MSRs increment every un-halted clock
at the actual and base frequency:

AVG_MHz = APERF_delta/measurement_interval

%Busy = MPERF_delta/TSC_delta

This quirk is needed for these calculations to also work on KNL,
which would otherwise show a value 1024x smaller than expected.

Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Staring in Linux-4.3-rc1,
commit 6fb3143b561c ("tools/power turbostat: dump CONFIG_TDP")
touches MSR 0x648, which is not supported on IVB-Xeon.
This results in "turbostat --debug" exiting on those systems:

turbostat: /dev/cpu/2/msr offset 0x648 read failed: Input/output error

Remove IVB-Xeon from the list of machines supporting with that MSR.

Signed-off-by: Len Brown <len.brown@intel.com>

Pull turbostat changes for v4.3 from Len Brown.

* 'turbostat' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: fix typo on DRAM column in Joules-mode
  tools/power turbostat: fix parameter passing for forked command
  tools/power turbostat: dump CONFIG_TDP
  tools/power turbostat: cpu0 is no longer hard-coded, so  update output
  tools/power turbostat: update turbostat(8)

< RAM_W
> RAM_J

Reported-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

turbostat supports forked command when sampling cpu state. However,
the forked command is not allowed to be executed with options, otherwise
turbostat might regard these options as invalid turbostat options.

For example:

./turbostat stress -c 4 -t 10
./turbostat: unrecognized option '-t'

Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Config TDP is a feature that allows parts to be configured
for different thermal limits after they have left the factory.

This can have an effect on the operation of the part,
particularly in determiniing...

Max Non-turbo Ratio
Turbo Activation Ratio

Signed-off-by: Len Brown <len.brown@intel.com>

The --debug option reads a number of per-package MSRs.
Previously we explicitly read them on cpu0, but recently
turbostat changed to read them on the current "base_cpu".

Update the print-out to reflect base_cpu, rather than
the hard-coded cpu0.

Signed-off-by: Len Brown <len.brown@intel.com>

This header containing all MSRs and respective bit definitions
got exported to userspace in conjunction with the big UAPI
shuffle.

But, it doesn't belong in the UAPI headers because userspace can
do its own MSR defines and exporting them from the kernel blocks
us from doing cleanups/renames in that header. Which is
ridiculous - it is not kernel's job to export such a header and
keep MSRs list and their names stable.

Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1433436928-31903-19-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>