linux.git/tools/testing/selftests/net/forwarding/ethtool_lib.sh, branch master

selftests: forwarding: Move several selftests

2024-03-29T01:03:42+00:00

The tests in net/forwarding are generally expected to be HW-independent.
There are however several tests that, while not depending on any HW in
particular, nevertheless depend on being used on HW interfaces. Placing
these selftests to net/forwarding is confusing, because the selftest will
just report it can't be run on veth pairs. At the same time, placing them
to a particular driver's selftests subdirectory would be wrong.

Instead, add a new directory, drivers/net/hw, where these generic but HW
independent selftests should be placed. Move over several such tests
including one helper library.

Since typically these tests will not be expected to run, omit the directory
drivers/net/hw from the TARGETS list in selftests/Makefile. Retain a
Makefile in the new directory itself, so that a user can make -C into that
directory and act on those tests explicitly.

Cc: Roger Quadros 
Cc: Tobias Waldekranz 
Cc: Danielle Ratson 
Cc: Davide Caratti 
Cc: Johannes Nixdorf 
Suggested-by: Jakub Kicinski 
Signed-off-by: Petr Machata 
Link: https://lore.kernel.org/r/e11dae1f62703059e9fc2240004288ac7cc15756.1711464583.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski

net: selftests: Add lanes setting test

2021-02-04T02:37:29+00:00

Test that setting lanes parameter is working.

Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.

And then, test that setting number of lanes larger than max lanes fails.

Do the above for both autoneg on and off.

$ ./ethtool_lanes.sh

TEST: 4 lanes is autonegotiated                                     [ OK ]
TEST: Lanes number larger than max width is not set                 [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode               [ OK ]
TEST: Lanes number larger than max width is not set                 [ OK ]

Signed-off-by: Danielle Ratson 
Signed-off-by: Jakub Kicinski

selftests: forwarding: ethtool: Move different_speeds_get() to ethtool_lib

2020-06-30T00:45:02+00:00

Currently different_speeds_get() is used only by ethtool.sh tests.
The function can be useful for another tests that check ethtool
configurations.

Move the function to ethtool_lib in order to allow other tests to use
it.

Signed-off-by: Amit Cohen 
Reviewed-by: Petr Machata 
Reviewed-by: Florian Fainelli 
Signed-off-by: Ido Schimmel 
Signed-off-by: David S. Miller

selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED

2020-03-25T19:01:18+00:00

The lib files should not be defined as TEST_PROGS, or we will run them
in run_kselftest.sh.

Also remove ethtool_lib.sh exec permission.

Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests")
Signed-off-by: Hangbin Liu 
Signed-off-by: David S. Miller

selftests: forwarding: Add ethtool_lib.sh

2019-11-19T01:11:54+00:00

Functions:
1. speeds_arr_get
	The function returns an array of speed values from
        /usr/include/linux/ethtool.h The array looks as follows:
	[10baseT/Half] = 0,
	[10baseT/Full] = 1,
	...

2. ethtool_set:
	params: cmd
	The function runs ethtool by cmd (ethtool -s cmd) and checks if
	there was an error in configuration

3. dev_speeds_get:
	params: dev, with_mode (0 or 1), adver (0 or 1)
	return value: Array of supported/Advertised link modes
	with/without mode

	* Example 1:
	speeds_get swp1 0 0
	return: 1000 10000 40000
	* Example 2:
	speeds_get swp1 1 1
	return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full

4. common_speeds_get:
	params: dev1, dev2, with_mode (0 or 1), adver (0 or 1)
	return value: Array of common speeds of dev1 and dev2

	* Example:
	common_speeds_get swp1 swp2 0 0
	return: 1000 10000
	Assuming that swp1 supports 1000 10000 40000 and swp2 supports
	1000 10000

Signed-off-by: Amit Cohen 
Signed-off-by: Ido Schimmel 
Signed-off-by: David S. Miller