Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "The first real batch of fixes for this release cycle, so there are a
  few more than usual.

  Most of these are fixes and tweaks to board support (DT bugfixes,
  etc).  I've also picked up a couple of small cleanups that seemed
  innocent enough that there was little reason to wait (const/
  __initconst and Kconfig deps).

  Quite a bit of the changes on OMAP were due to fixes to no longer
  write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
  there were also other fixes.

  Kirkwood had a bunch of gpio fixes for some boards.  OMAP had RTC
  fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.

  All in all, mostly the usual mix of various fixes"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
  ARM: multi_v7_defconfig: enable DW_WATCHDOG
  ARM: nomadik: fix up SD/MMC DT settings
  ARM64: tegra: Add chosen node for tegra132 norrin
  ARM: realview: use "depends on" instead of "if" after prompt
  ARM: tango: use "depends on" instead of "if" after prompt
  ARM: tango: use const and __initconst for smp_operations
  ARM: realview: use const and __initconst for smp_operations
  bus: uniphier-system-bus: revive tristate prompt
  arm64: dts: Add missing DMA Abort interrupt to Juno
  bus: vexpress-config: Add missing of_node_put
  ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
  ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
  ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
  ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
  ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
  ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
  ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
  ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
  ARM: dts: am4372: fix irq type for arm twd and global timer
  ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
  ...

33 files changed, 230 insertions, 149 deletions

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 04885f9f959e..1fafaad516ba 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -439,6 +439,7 @@
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
 			mbox_wkupm3: wkup_m3 {
+				ti,mbox-send-noirq;
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <0 0 3>;
 			};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index df955ba4dc62..92068fbf8b57 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -73,7 +73,7 @@
 	global_timer: timer@48240200 {
 		compatible = "arm,cortex-a9-global-timer";
 		reg = <0x48240200 0x100>;
-		interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 		interrupt-parent = <&gic>;
 		clocks = <&mpu_periphclk>;
 	};
@@ -81,7 +81,7 @@
 	local_timer: timer@48240600 {
 		compatible = "arm,cortex-a9-twd-timer";
 		reg = <0x48240600 0x100>;
-		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
 		interrupt-parent = <&gic>;
 		clocks = <&mpu_periphclk>;
 	};
@@ -290,6 +290,7 @@
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
 			mbox_wkupm3: wkup_m3 {
+				ti,mbox-send-noirq;
 				ti,mbox-tx = <0 0 0>;
 				ti,mbox-rx = <0 0 3>;
 			};
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index 64d43325bcbc..ecd09ab6d581 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -590,8 +590,6 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pixcir_ts_pins>;
 		reg = <0x5c>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <22 0>;
 
 		attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 
@@ -599,7 +597,7 @@
 		 * 0x264 represents the offset of padconf register of
 		 * gpio3_22 from am43xx_pinmux base.
 		 */
-		interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>,
+		interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>,
 				      <&am43xx_pinmux 0x264>;
 		interrupt-names = "tsc", "wakeup";
 
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 746fd2b17958..d580e2b70f9a 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -491,7 +491,7 @@
 		pinctrl-0 = <&pixcir_ts_pins>;
 		reg = <0x5c>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <17 0>;
+		interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
 
 		attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
 
diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
index c53882643ae9..8d93882dc8d5 100644
--- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
@@ -167,7 +167,7 @@
 			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
 			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
 			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLUP | MUX_MODE3)	/* vin2a_d23.rgmii1_rd0 */
+			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
 		>;
 	};
 
@@ -492,14 +492,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&qspi1_pins>;
 
-	spi-max-frequency = <20000000>;
+	spi-max-frequency = <48000000>;
 
 	spi_flash: spi_flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;				/* CS0 */
-		spi-max-frequency = <20000000>;
+		spi-max-frequency = <48000000>;
 
 		partition@0 {
 			label = "uboot";
@@ -559,13 +559,13 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-txid";
 	dual_emac_res_vlan = <0>;
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-txid";
 	dual_emac_res_vlan = <1>;
 };
 
@@ -588,7 +588,7 @@
 };
 
 &usb2 {
-	dr_mode = "peripheral";
+	dr_mode = "host";
 };
 
 &mcasp3 {
diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts
index 77bb8e17401a..988e99632d49 100644
--- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts
@@ -25,8 +25,8 @@
 &dra7_pmx_core {
 	uart3_pins_default: uart3_pins_default {
 		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2)	/* uart2_ctsn.uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1)	/* uart2_rtsn.uart3_txd */
+			DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_rxd */
+			DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0)	/* uart3_txd */
 		>;
 	};
 
@@ -108,9 +108,9 @@
 	pinctrl-0 = <&i2c5_pins_default>;
 	clock-frequency = <400000>;
 
-	eeprom_base: atmel@50 {
+	eeprom_base: atmel@54 {
 		compatible = "atmel,24c08";
-		reg = <0x50>;
+		reg = <0x54>;
 		pagesize = <16>;
 	};
 
diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
index 13cf69a8d0fb..fb9e1bbf2338 100644
--- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
+++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
@@ -152,6 +152,7 @@
 				nand-on-flash-bbt;
 
 				partitions {
+					compatible = "fixed-partitions";
 					#address-cells = <1>;
 					#size-cells = <1>;
 
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 77ddff036409..e683856c507c 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -114,9 +114,15 @@
 
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_macb0_default>;
+				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
 				phy-mode = "rmii";
 				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioA>;
+					interrupts = <73 IRQ_TYPE_LEVEL_LOW>;
+				};
 			};
 
 			pdmic@f8018000 {
@@ -300,6 +306,10 @@
 					bias-disable;
 				};
 
+				pinctrl_macb0_phy_irq: macb0_phy_irq {
+					pinmux = <PIN_PC9__GPIO>;
+				};
+
 				pinctrl_pdmic_default: pdmic_default {
 					pinmux = <PIN_PB26__PDMIC_DAT>,
 						<PIN_PB27__PDMIC_CLK>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index 131614f28e75..569026e8f96c 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -86,10 +86,12 @@
 			macb0: ethernet@f8020000 {
 				phy-mode = "rmii";
 				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
 
 				phy0: ethernet-phy@1 {
 					interrupt-parent = <&pioE>;
-					interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+					interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 					reg = <1>;
 				};
 			};
@@ -152,6 +154,10 @@
 						atmel,pins =
 							<AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
+					pinctrl_macb0_phy_irq: macb0_phy_irq_0 {
+						atmel,pins =
+							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index 2d4a33100af6..4e98cda97403 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -160,8 +160,15 @@
 			};
 
 			macb0: ethernet@f8020000 {
+				pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
 				phy-mode = "rmii";
 				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioE>;
+					interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+				};
 			};
 
 			mmc1: mmc@fc000000 {
@@ -193,6 +200,10 @@
 
 			pinctrl@fc06a000 {
 				board {
+					pinctrl_macb0_phy_irq: macb0_phy_irq {
+						atmel,pins =
+							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
 					pinctrl_mmc0_cd: mmc0_cd {
 						atmel,pins =
 							<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index ca4ddf86817a..626c67d66626 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -215,7 +215,7 @@
 	};
 
 	panel: panel {
-		compatible = "qd,qd43003c0-40", "simple-panel";
+		compatible = "qiaodian,qd43003c0-40", "simple-panel";
 		backlight = <&backlight>;
 		power-supply = <&panel_reg>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/kirkwood-lswvl.dts b/arch/arm/boot/dts/kirkwood-lswvl.dts
index 09eed3cea0af..36eec7392ab4 100644
--- a/arch/arm/boot/dts/kirkwood-lswvl.dts
+++ b/arch/arm/boot/dts/kirkwood-lswvl.dts
@@ -1,7 +1,8 @@
 /*
  * Device Tree file for Buffalo Linkstation LS-WVL/VL
  *
- * Copyright (C) 2015, rogershimizu@gmail.com
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -156,21 +157,21 @@
 		button@1 {
 			label = "Function Button";
 			linux,code = <KEY_OPTION>;
-			gpios = <&gpio0 45 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 		};
 
 		button@2 {
 			label = "Power-on Switch";
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <5>;
-			gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
 
 		button@3 {
 			label = "Power-auto Switch";
 			linux,code = <KEY_ESC>;
 			linux,input-type = <5>;
-			gpios = <&gpio0 47 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -185,38 +186,38 @@
 
 		led@1 {
 			label = "lswvl:red:alarm";
-			gpios = <&gpio0 36 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@2 {
 			label = "lswvl:red:func";
-			gpios = <&gpio0 37 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@3 {
 			label = "lswvl:amber:info";
-			gpios = <&gpio0 38 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@4 {
 			label = "lswvl:blue:func";
-			gpios = <&gpio0 39 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@5 {
 			label = "lswvl:blue:power";
-			gpios = <&gpio0 40 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
 
 		led@6 {
 			label = "lswvl:red:hdderr0";
-			gpios = <&gpio0 34 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@7 {
 			label = "lswvl:red:hdderr1";
-			gpios = <&gpio0 35 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -233,7 +234,7 @@
 				3250 1
 				5000 0>;
 
-		alarm-gpios = <&gpio0 43 GPIO_ACTIVE_HIGH>;
+		alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 	};
 
 	restart_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-lswxl.dts b/arch/arm/boot/dts/kirkwood-lswxl.dts
index f5db16a08597..b13ec20a7088 100644
--- a/arch/arm/boot/dts/kirkwood-lswxl.dts
+++ b/arch/arm/boot/dts/kirkwood-lswxl.dts
@@ -1,7 +1,8 @@
 /*
  * Device Tree file for Buffalo Linkstation LS-WXL/WSXL
  *
- * Copyright (C) 2015, rogershimizu@gmail.com
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -156,21 +157,21 @@
 		button@1 {
 			label = "Function Button";
 			linux,code = <KEY_OPTION>;
-			gpios = <&gpio1 41 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 		};
 
 		button@2 {
 			label = "Power-on Switch";
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <5>;
-			gpios = <&gpio1 42 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
 		};
 
 		button@3 {
 			label = "Power-auto Switch";
 			linux,code = <KEY_ESC>;
 			linux,input-type = <5>;
-			gpios = <&gpio1 43 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -185,12 +186,12 @@
 
 		led@1 {
 			label = "lswxl:blue:func";
-			gpios = <&gpio1 36 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 		};
 
 		led@2 {
 			label = "lswxl:red:alarm";
-			gpios = <&gpio1 49 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
 
 		led@3 {
@@ -200,23 +201,23 @@
 
 		led@4 {
 			label = "lswxl:blue:power";
-			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
 		};
 
 		led@5 {
 			label = "lswxl:red:func";
-			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@6 {
 			label = "lswxl:red:hdderr0";
-			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
 		};
 
 		led@7 {
 			label = "lswxl:red:hdderr1";
-			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -225,15 +226,15 @@
 		pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
 		pinctrl-names = "default";
 
-		gpios = <&gpio0 47 GPIO_ACTIVE_LOW
-			 &gpio0 48 GPIO_ACTIVE_LOW>;
+		gpios = <&gpio1 16 GPIO_ACTIVE_LOW
+			 &gpio1 15 GPIO_ACTIVE_LOW>;
 
 		gpio-fan,speed-map = <0 3
 				1500 2
 				3250 1
 				5000 0>;
 
-		alarm-gpios = <&gpio1 49 GPIO_ACTIVE_HIGH>;
+		alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 
 	restart_poweroff {
@@ -256,7 +257,7 @@
 			enable-active-high;
 			regulator-always-on;
 			regulator-boot-on;
-			gpio = <&gpio0 37 GPIO_ACTIVE_HIGH>;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		};
 		hdd_power0: regulator@2 {
 			compatible = "regulator-fixed";
diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
index 1db6f2c506cc..8082d64266a3 100644
--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
@@ -131,6 +131,7 @@
 	chip-delay = <40>;
 	status = "okay";
 	partitions {
+		compatible = "fixed-partitions";
 		#address-cells = <1>;
 		#size-cells = <1>;
 
diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
index 7fed0bd4f3de..00805322367e 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
@@ -112,14 +112,6 @@
 	clock-frequency = <400000>;
 };
 
-&i2c2 {
-	clock-frequency = <400000>;
-};
-
-&i2c3 {
-	clock-frequency = <400000>;
-};
-
 /*
  * Only found on the wireless SOM. For the SOM without wireless, the pins for
  * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
@@ -143,6 +135,7 @@
 		interrupt-parent = <&gpio5>;
 		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
 		ref-clock-frequency = <26000000>;
+		tcxo-clock-frequency = <26000000>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
index 888412c63f97..902657d6713b 100644
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -130,6 +130,16 @@
 	};
 };
 
+&gpio8 {
+	/* TI trees use GPIO instead of msecure, see also muxing */
+	p234 {
+		gpio-hog;
+		gpios = <10 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio8_234/msecure";
+	};
+};
+
 &omap5_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
@@ -213,6 +223,13 @@
 		>;
 	};
 
+	/* TI trees use GPIO mode; msecure mode does not work reliably? */
+	palmas_msecure_pins: palmas_msecure_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
+		>;
+	};
+
 	usbhost_pins: pinmux_usbhost_pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
@@ -278,6 +295,12 @@
 			&usbhost_wkup_pins
 	>;
 
+	palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */
+		>;
+	};
+
 	usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
 		pinctrl-single,pins = <
 			OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
@@ -345,6 +368,8 @@
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
 
 		extcon_usb3: palmas_usb {
 			compatible = "ti,palmas-usb-vid";
@@ -358,6 +383,14 @@
 			#clock-cells = <0>;
 		};
 
+		rtc {
+			compatible = "ti,palmas-rtc";
+			interrupt-parent = <&palmas>;
+			interrupts = <8 IRQ_TYPE_NONE>;
+			ti,backup-battery-chargeable;
+			ti,backup-battery-charge-high-current;
+		};
+
 		palmas_pmic {
 			compatible = "ti,palmas-pmic";
 			interrupt-parent = <&palmas>;
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
index 3daec912b4bf..420788229e6f 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
+++ b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
@@ -1,7 +1,8 @@
 /*
  * Device Tree file for Buffalo Linkstation LS-WTGL
  *
- * Copyright (C) 2015, Roger Shimizu <rogershimizu@gmail.com>
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -69,8 +70,6 @@
 
 		internal-regs {
 			pinctrl: pinctrl@10000 {
-				pinctrl-0 = <&pmx_usb_power &pmx_power_hdd
-					&pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
 				pinctrl-names = "default";
 
 				pmx_led_power: pmx-leds {
@@ -162,6 +161,7 @@
 		led@1 {
 			label = "lswtgl:blue:power";
 			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
 		};
 
 		led@2 {
@@ -188,7 +188,7 @@
 				3250 1
 				5000 0>;
 
-		alarm-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		alarm-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 	};
 
 	restart_poweroff {
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index b8032bca4621..db1151c18466 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -1342,7 +1342,7 @@
 			dbgu: serial@fc069000 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfc069000 0x200>;
-				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
+				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
 				clocks = <&dbgu_clk>;
diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
index d0c743853318..27a333eb8987 100644
--- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
+++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
@@ -127,22 +127,14 @@
 			};
 			mmcsd_default_mode: mmcsd_default {
 				mmcsd_default_cfg1 {
-					/* MCCLK */
-					pins = "GPIO8_B10";
-					ste,output = <0>;
-				};
-				mmcsd_default_cfg2 {
-					/* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
-					pins = "GPIO10_C11", "GPIO15_A12",
-					"GPIO16_C13", "GPIO23_D15";
-					ste,output = <1>;
-				};
-				mmcsd_default_cfg3 {
-					/* MCCMD, MCDAT3-0, MCMSFBCLK */
-					pins = "GPIO9_A10", "GPIO11_B11",
-					"GPIO12_A11", "GPIO13_C12",
-					"GPIO14_B12", "GPIO24_C15";
-					ste,input = <1>;
+					/*
+					 * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+					 * MCCMD, MCDAT3-0, MCMSFBCLK
+					 */
+					pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+					       "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+					       "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+					ste,output = <2>;
 				};
 			};
 		};
@@ -802,10 +794,21 @@
 			clock-names = "mclk", "apb_pclk";
 			interrupt-parent = <&vica>;
 			interrupts = <22>;
-			max-frequency = <48000000>;
+			max-frequency = <400000>;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
+			full-pwr-cycle;
+			/*
+			 * The STw4811 circuit used with the Nomadik strictly
+			 * requires that all of these signal direction pins be
+			 * routed and used for its 4-bit levelshifter.
+			 */
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-dir-dat31;
+			st,sig-dir-cmd;
+			st,sig-pin-fbclk;
 			pinctrl-names = "default";
 			pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
 			vmmc-supply = <&vmmc_regulator>;
di