b43: move under broadcom vendor directory

Part of reorganising wireless drivers directory and Kconfig.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

63 files changed, 58116 insertions, 0 deletions

diff --git a/drivers/net/wireless/broadcom/b43/Kconfig b/drivers/net/wireless/broadcom/b43/Kconfig
new file mode 100644
index 000000000000..fba856032ca5
--- /dev/null
+++ b/drivers/net/wireless/broadcom/b43/Kconfig
@@ -0,0 +1,187 @@
+config B43
+	tristate "Broadcom 43xx wireless support (mac80211 stack)"
+	depends on (BCMA_POSSIBLE || SSB_POSSIBLE) && MAC80211 && HAS_DMA
+	select BCMA if B43_BCMA
+	select SSB if B43_SSB
+	select FW_LOADER
+	---help---
+	  b43 is a driver for the Broadcom 43xx series wireless devices.
+
+	  Check "lspci" for something like
+	  "Broadcom Corporation BCM43XX 802.11 Wireless LAN Controller"
+	  to determine whether you own such a device.
+
+	  This driver supports the new BCM43xx IEEE 802.11G devices, but not
+	  the old IEEE 802.11B devices. Old devices are supported by
+	  the b43legacy driver.
+	  Note that this has nothing to do with the standard that your AccessPoint
+	  supports (A, B, G or a combination).
+	  IEEE 802.11G devices can talk to IEEE 802.11B AccessPoints.
+
+	  It is safe to include both b43 and b43legacy as the underlying glue
+	  layer will automatically load the correct version for your device.
+
+	  This driver uses V4 firmware, which must be installed separately using
+	  b43-fwcutter.
+
+	  This driver can be built as a module (recommended) that will be called "b43".
+	  If unsure, say M.
+
+config B43_BCMA
+	bool
+
+config B43_SSB
+	bool
+
+choice
+	prompt "Supported bus types"
+	depends on B43
+	default B43_BUSES_BCMA_AND_SSB
+
+config B43_BUSES_BCMA_AND_SSB
+	bool "BCMA and SSB"
+	depends on BCMA_POSSIBLE && SSB_POSSIBLE
+	select B43_BCMA
+	select B43_SSB
+
+config B43_BUSES_BCMA
+	bool "BCMA only"
+	depends on BCMA_POSSIBLE
+	select B43_BCMA
+
+config B43_BUSES_SSB
+	bool "SSB only"
+	depends on SSB_POSSIBLE
+	select B43_SSB
+
+endchoice
+
+# Auto-select SSB PCI-HOST support, if possible
+config B43_PCI_AUTOSELECT
+	bool
+	depends on B43 && SSB_PCIHOST_POSSIBLE
+	select SSB_PCIHOST
+	select SSB_B43_PCI_BRIDGE
+	default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B43_PCICORE_AUTOSELECT
+	bool
+	depends on B43 && SSB_DRIVER_PCICORE_POSSIBLE
+	select SSB_DRIVER_PCICORE
+	default y
+
+config B43_SDIO
+	bool "Broadcom 43xx SDIO device support"
+	depends on B43 && B43_SSB && SSB_SDIOHOST_POSSIBLE
+	select SSB_SDIOHOST
+	---help---
+	  Broadcom 43xx device support for Soft-MAC SDIO devices.
+
+	  With this config option you can drive Soft-MAC b43 cards with a
+	  Secure Digital I/O interface.
+	  This includes the WLAN daughter card found on the Nintendo Wii
+	  video game console.
+	  Note that this does not support Broadcom 43xx Full-MAC devices.
+
+	  It's safe to select Y here, even if you don't have a B43 SDIO device.
+
+	  If unsure, say N.
+
+#Data transfers to the device via PIO. We want it as a fallback even
+# if we can do DMA.
+config B43_BCMA_PIO
+	bool
+	depends on B43 && B43_BCMA
+	select BCMA_BLOCKIO
+	default y
+
+config B43_PIO
+	bool
+	depends on B43 && B43_SSB
+	select SSB_BLOCKIO
+	default y
+
+config B43_PHY_G
+	bool "Support for G-PHY (802.11g) devices"
+	depends on B43 && B43_SSB
+	default y
+	---help---
+	  This PHY type can be found in the following chipsets:
+	  PCI: BCM4306, BCM4311, BCM4318
+	  SoC: BCM4712, BCM5352E
+
+config B43_PHY_N
+	bool "Support for N-PHY (the main 802.11n series) devices"
+	depends on B43
+	default y
+	---help---
+	  This PHY type can be found in the following chipsets:
+	  PCI: BCM4321, BCM4322,
+	       BCM43222, BCM43224, BCM43225,
+	       BCM43131, BCM43217, BCM43227, BCM43228
+	  SoC: BCM4716, BCM4717, BCM4718, BCM5356, BCM5357, BCM5358
+
+config B43_PHY_LP
+	bool "Support for LP-PHY (low-power 802.11g) devices"
+	depends on B43 && B43_SSB
+	default y
+	---help---
+	  The LP-PHY is a low-power PHY built into some notebooks
+	  and embedded devices. It supports 802.11a/b/g
+	  (802.11a support is optional, and currently disabled).
+
+config B43_PHY_HT
+	bool "Support for HT-PHY (high throughput 802.11n) devices"
+	depends on B43 && B43_BCMA
+	default y
+	---help---
+	  This PHY type with 3x3:3 MIMO can be found in the BCM4331 PCI chipset.
+
+config B43_PHY_LCN
+	bool "Support for LCN-PHY devices (BROKEN)"
+	depends on B43 && BROKEN
+	---help---
+	  Support for the LCN-PHY.
+
+	  Say N, this is BROKEN and crashes driver.
+
+config B43_PHY_AC
+	bool "Support for AC-PHY (802.11ac) devices (BROKEN)"
+	depends on B43 && B43_BCMA && BROKEN
+	---help---
+	  This PHY type can be found in the following chipsets:
+	  PCI: BCM4352, BCM4360
+
+	  Say N, this is BROKEN and crashes driver.
+
+# This config option automatically enables b43 LEDS support,
+# if it's possible.
+config B43_LEDS
+	bool
+	depends on B43 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = B43)
+	default y
+
+# This config option automatically enables b43 HW-RNG support,
+# if the HW-RNG core is enabled.
+config B43_HWRNG
+	bool
+	depends on B43 && (HW_RANDOM = y || HW_RANDOM = B43)
+	default y
+
+config B43_DEBUG
+	bool "Broadcom 43xx debugging"
+	depends on B43
+	---help---
+	  Broadcom 43xx debugging.
+
+	  This adds additional runtime sanity checks and statistics to the driver.
+	  These checks and statistics might be expensive and hurt the runtime
+	  performance of your system.
+	  This also adds the b43 debugfs interface.
+
+	  Do not enable this, unless you are debugging the driver.
+
+	  Say N, if you are a distributor or user building a release kernel
+	  for production use.
+	  Only say Y, if you are debugging a problem in the b43 driver sourcecode.
diff --git a/drivers/net/wireless/broadcom/b43/Makefile b/drivers/net/wireless/broadcom/b43/Makefile
new file mode 100644
index 000000000000..ddc4df46656f
--- /dev/null
+++ b/drivers/net/wireless/broadcom/b43/Makefile
@@ -0,0 +1,27 @@
+b43-y				+= main.o
+b43-y				+= bus.o
+b43-$(CONFIG_B43_PHY_G)		+= phy_a.o phy_g.o tables.o lo.o wa.o
+b43-$(CONFIG_B43_PHY_N)		+= tables_nphy.o
+b43-$(CONFIG_B43_PHY_N)		+= radio_2055.o
+b43-$(CONFIG_B43_PHY_N)		+= radio_2056.o
+b43-$(CONFIG_B43_PHY_N)		+= radio_2057.o
+b43-y				+= phy_common.o
+b43-$(CONFIG_B43_PHY_N)		+= phy_n.o
+b43-$(CONFIG_B43_PHY_LP)	+= phy_lp.o
+b43-$(CONFIG_B43_PHY_LP)	+= tables_lpphy.o
+b43-$(CONFIG_B43_PHY_HT)	+= phy_ht.o
+b43-$(CONFIG_B43_PHY_HT)	+= tables_phy_ht.o
+b43-$(CONFIG_B43_PHY_HT)	+= radio_2059.o
+b43-$(CONFIG_B43_PHY_LCN)	+= phy_lcn.o tables_phy_lcn.o
+b43-$(CONFIG_B43_PHY_AC)	+= phy_ac.o
+b43-y				+= sysfs.o
+b43-y				+= xmit.o
+b43-y				+= dma.o
+b43-y				+= pio.o
+b43-y				+= rfkill.o
+b43-y				+= ppr.o
+b43-$(CONFIG_B43_LEDS)		+= leds.o
+b43-$(CONFIG_B43_SDIO)		+= sdio.o
+b43-$(CONFIG_B43_DEBUG)		+= debugfs.o
+
+obj-$(CONFIG_B43)		+= b43.o
diff --git a/drivers/net/wireless/broadcom/b43/b43.h b/drivers/net/wireless/broadcom/b43/b43.h
new file mode 100644
index 000000000000..036552439816
--- /dev/null
+++ b/drivers/net/wireless/broadcom/b43/b43.h
@@ -0,0 +1,1108 @@
+#ifndef B43_H_
+#define B43_H_
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/hw_random.h>
+#include <linux/bcma/bcma.h>
+#include <linux/ssb/ssb.h>
+#include <linux/completion.h>
+#include <net/mac80211.h>
+
+#include "debugfs.h"
+#include "leds.h"
+#include "rfkill.h"
+#include "bus.h"
+#include "lo.h"
+#include "phy_common.h"
+
+
+#ifdef CONFIG_B43_DEBUG
+# define B43_DEBUG	1
+#else
+# define B43_DEBUG	0
+#endif
+
+/* MMIO offsets */
+#define B43_MMIO_DMA0_REASON		0x20
+#define B43_MMIO_DMA0_IRQ_MASK		0x24
+#define B43_MMIO_DMA1_REASON		0x28
+#define B43_MMIO_DMA1_IRQ_MASK		0x2C
+#define B43_MMIO_DMA2_REASON		0x30
+#define B43_MMIO_DMA2_IRQ_MASK		0x34
+#define B43_MMIO_DMA3_REASON		0x38
+#define B43_MMIO_DMA3_IRQ_MASK		0x3C
+#define B43_MMIO_DMA4_REASON		0x40
+#define B43_MMIO_DMA4_IRQ_MASK		0x44
+#define B43_MMIO_DMA5_REASON		0x48
+#define B43_MMIO_DMA5_IRQ_MASK		0x4C
+#define B43_MMIO_MACCTL			0x120	/* MAC control */
+#define B43_MMIO_MACCMD			0x124	/* MAC command */
+#define B43_MMIO_GEN_IRQ_REASON		0x128
+#define B43_MMIO_GEN_IRQ_MASK		0x12C
+#define B43_MMIO_RAM_CONTROL		0x130
+#define B43_MMIO_RAM_DATA		0x134
+#define B43_MMIO_PS_STATUS		0x140
+#define B43_MMIO_RADIO_HWENABLED_HI	0x158
+#define B43_MMIO_MAC_HW_CAP		0x15C	/* MAC capabilities (corerev >= 13) */
+#define B43_MMIO_SHM_CONTROL		0x160
+#define B43_MMIO_SHM_DATA		0x164
+#define B43_MMIO_SHM_DATA_UNALIGNED	0x166
+#define B43_MMIO_XMITSTAT_0		0x170
+#define B43_MMIO_XMITSTAT_1		0x174
+#define B43_MMIO_REV3PLUS_TSF_LOW	0x180	/* core rev >= 3 only */
+#define B43_MMIO_REV3PLUS_TSF_HIGH	0x184	/* core rev >= 3 only */
+#define B43_MMIO_TSF_CFP_REP		0x188
+#define B43_MMIO_TSF_CFP_START		0x18C
+#define B43_MMIO_TSF_CFP_MAXDUR		0x190
+
+/* 32-bit DMA */
+#define B43_MMIO_DMA32_BASE0		0x200
+#define B43_MMIO_DMA32_BASE1		0x220
+#define B43_MMIO_DMA32_BASE2		0x240
+#define B43_MMIO_DMA32_BASE3		0x260
+#define B43_MMIO_DMA32_BASE4		0x280
+#define B43_MMIO_DMA32_BASE5		0x2A0
+/* 64-bit DMA */
+#define B43_MMIO_DMA64_BASE0		0x200
+#define B43_MMIO_DMA64_BASE1		0x240
+#define B43_MMIO_DMA64_BASE2		0x280
+#define B43_MMIO_DMA64_BASE3		0x2C0
+#define B43_MMIO_DMA64_BASE4		0x300
+#define B43_MMIO_DMA64_BASE5		0x340
+
+/* PIO on core rev < 11 */
+#define B43_MMIO_PIO_BASE0		0x300
+#define B43_MMIO_PIO_BASE1		0x310
+#define B43_MMIO_PIO_BASE2		0x320
+#define B43_MMIO_PIO_BASE3		0x330
+#define B43_MMIO_PIO_BASE4		0x340
+#define B43_MMIO_PIO_BASE5		0x350
+#define B43_MMIO_PIO_BASE6		0x360
+#define B43_MMIO_PIO_BASE7		0x370
+/* PIO on core rev >= 11 */
+#define B43_MMIO_PIO11_BASE0		0x200
+#define B43_MMIO_PIO11_BASE1		0x240
+#define B43_MMIO_PIO11_BASE2		0x280
+#define B43_MMIO_PIO11_BASE3		0x2C0
+#define B43_MMIO_PIO11_BASE4		0x300
+#define B43_MMIO_PIO11_BASE5		0x340
+
+#define B43_MMIO_RADIO24_CONTROL	0x3D8	/* core rev >= 24 only */
+#define B43_MMIO_RADIO24_DATA		0x3DA	/* core rev >= 24 only */
+#define B43_MMIO_PHY_VER		0x3E0
+#define B43_MMIO_PHY_RADIO		0x3E2
+#define B43_MMIO_PHY0			0x3E6
+#define B43_MMIO_ANTENNA		0x3E8
+#define B43_MMIO_CHANNEL		0x3F0
+#define B43_MMIO_CHANNEL_EXT		0x3F4
+#define B43_MMIO_RADIO_CONTROL		0x3F6
+#define B43_MMIO_RADIO_DATA_HIGH	0x3F8
+#define B43_MMIO_RADIO_DATA_LOW		0x3FA
+#define B43_MMIO_PHY_CONTROL		0x3FC
+#define B43_MMIO_PHY_DATA		0x3FE
+#define B43_MMIO_MACFILTER_CONTROL	0x420
+#define B43_MMIO_MACFILTER_DATA		0x422
+#define B43_MMIO_RCMTA_COUNT		0x43C
+#define B43_MMIO_PSM_PHY_HDR		0x492
+#define B43_MMIO_RADIO_HWENABLED_LO	0x49A
+#define B43_MMIO_GPIO_CONTROL		0x49C
+#define B43_MMIO_GPIO_MASK		0x49E
+#define B43_MMIO_TXE0_CTL		0x500
+#define B43_MMIO_TXE0_AUX		0x502
+#define B43_MMIO_TXE0_TS_LOC		0x504
+#define B43_MMIO_TXE0_TIME_OUT		0x506
+#define B43_MMIO_TXE0_WM_0		0x508
+#define B43_MMIO_TXE0_WM_1		0x50A
+#define B43_MMIO_TXE0_PHYCTL		0x50C
+#define B43_MMIO_TXE0_STATUS		0x50E
+#define B43_MMIO_TXE0_MMPLCP0		0x510
+#define B43_MMIO_TXE0_MMPLCP1		0x512
+#define B43_MMIO_TXE0_PHYCTL1		0x514
+#define B43_MMIO_XMTFIFODEF		0x520
+#define B43_MMIO_XMTFIFO_FRAME_CNT	0x522	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFO_BYTE_CNT	0x524	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFO_HEAD		0x526	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFO_RD_PTR		0x528	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFO_WR_PTR		0x52A	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFODEF1		0x52C	/* core rev>= 16 only */
+#define B43_MMIO_XMTFIFOCMD		0x540
+#define B43_MMIO_XMTFIFOFLUSH		0x542
+#define B43_MMIO_XMTFIFOTHRESH		0x544
+#define B43_MMIO_XMTFIFORDY		0x546
+#define B43_MMIO_XMTFIFOPRIRDY		0x548
+#define B43_MMIO_XMTFIFORQPRI		0x54A
+#define B43_MMIO_XMTTPLATETXPTR		0x54C
+#define B43_MMIO_XMTTPLATEPTR		0x550
+#define B43_MMIO_SMPL_CLCT_STRPTR	0x552	/* core rev>= 22 only */
+#define B43_MMIO_SMPL_CLCT_STPPTR	0x554	/* core rev>= 22 only */
+#define B43_MMIO_SMPL_CLCT_CURPTR	0x556	/* core rev>= 22 only */
+#define B43_MMIO_XMTTPLATEDATALO	0x560
+#define B43_MMIO_XMTTPLATEDATAHI	0x562
+#define B43_MMIO_XMTSEL			0x568
+#define B43_MMIO_XMTTXCNT		0x56A
+#define B43_MMIO_XMTTXSHMADDR		0x56C
+#define B43_MMIO_TSF_CFP_START_LOW	0x604
+#define B43_MMIO_TSF_CFP_START_HIGH	0x606
+#define B43_MMIO_TSF_CFP_PRETBTT	0x612
+#define B43_MMIO_TSF_CLK_FRAC_LOW	0x62E
+#define B43_MMIO_TSF_CLK_FRAC_HIGH	0x630
+#define B43_MMIO_TSF_0			0x632	/* core rev < 3 only */
+#define B43_MMIO_TSF_1			0x634	/* core rev < 3 only */
+#define B43_MMIO_TSF_2			0x636	/* core rev < 3 only */
+#define B43_MMIO_TSF_3			0x638	/* core rev < 3 only */
+#define B43_MMIO_RNG			0x65A
+#define B43_MMIO_IFSSLOT		0x684	/* Interframe slot time */
+#define B43_MMIO_IFSCTL			0x688	/* Interframe space control */
+#define B43_MMIO_IFSSTAT		0x690
+#define B43_MMIO_IFSMEDBUSYCTL		0x692
+#define B43_MMIO_IFTXDUR		0x694
+#define  B43_MMIO_IFSCTL_USE_EDCF	0x0004
+#define B43_MMIO_POWERUP_DELAY		0x6A8
+#define B43_MMIO_BTCOEX_CTL		0x6B4 /* Bluetooth Coexistence Control */
+#define B43_MMIO_BTCOEX_STAT		0x6B6 /* Bluetooth Coexistence Status */
+#define B43_MMIO_BTCOEX_TXCTL		0x6B8 /* Bluetooth Coexistence Transmit Control */
+#define B43_MMIO_WEPCTL			0x7C0
+
+/* SPROM boardflags_lo values */
+#define B43_BFL_BTCOEXIST		0x0001	/* implements Bluetooth coexistance */
+#define B43_BFL_PACTRL			0x0002	/* GPIO 9 controlling the PA */
+#define B43_BFL_AIRLINEMODE		0x0004	/* implements GPIO 13 radio disable indication */
+#define B43_BFL_RSSI			0x0008	/* software calculates nrssi slope. */
+#define B43_BFL_ENETSPI			0x0010	/* has ephy roboswitch spi */
+#define B43_BFL_XTAL_NOSLOW		0x0020	/* no slow clock available */
+#define B43_BFL_CCKHIPWR		0x0040	/* can do high power CCK transmission */
+#define B43_BFL_ENETADM			0x0080	/* has ADMtek switch */
+#define B43_BFL_ENETVLAN		0x0100	/* can do vlan */
+#define B43_BFL_AFTERBURNER		0x0200	/* supports Afterburner mode */
+#define B43_BFL_NOPCI			0x0400	/* leaves PCI floating */
+#define B43_BFL_FEM			0x0800	/* supports the Front End Module */
+#define B43_BFL_EXTLNA			0x1000	/* has an external LNA */
+#define B43_BFL_HGPA			0x2000	/* had high gain PA */
+#define B43_BFL_BTCMOD			0x4000	/* BFL_BTCOEXIST is given in alternate GPIOs */
+#define B43_BFL_ALTIQ			0x8000	/* alternate I/Q settings */
+
+/* SPROM boardflags_hi values */
+#define B43_BFH_NOPA			0x0001	/* has no PA */
+#define B43_BFH_RSSIINV			0x0002	/* RSSI uses positive slope (not TSSI) */
+#define B43_BFH_PAREF			0x0004	/* uses the PARef LDO */
+#define B43_BFH_3TSWITCH		0x0008	/* uses a triple throw switch shared
+						 * with bluetooth */
+#define B43_BFH_PHASESHIFT		0x0010	/* can support phase shifter */
+#define B43_BFH_BUCKBOOST		0x0020	/* has buck/booster */
+#define B43_BFH_FEM_BT			0x0040	/* has FEM and switch to share antenna
+						 * with bluetooth */
+#define B43_BFH_NOCBUCK			0x0080
+#define B43_BFH_PALDO			0x0200
+#define B43_BFH_EXTLNA_5GHZ		0x1000	/* has an external LNA (5GHz mode) */
+
+/* SPROM boardflags2_lo values */
+#define B43_BFL2_RXBB_INT_REG_DIS	0x0001	/* external RX BB regulator present */
+#define B43_BFL2_APLL_WAR		0x0002	/* alternative A-band PLL settings implemented */
+#define B43_BFL2_TXPWRCTRL_EN 		0x0004	/* permits enabling TX Power Control */
+#define B43_BFL2_2X4_DIV		0x0008	/* 2x4 diversity switch */
+#define B43_BFL2_5G_PWRGAIN		0x0010	/* supports 5G band power gain */
+#define B43_BFL2_PCIEWAR_OVR		0x0020	/* overrides ASPM and Clkreq settings */
+#define B43_BFL2_CAESERS_BRD		0x0040	/* is Caesers board (unused) */
+#define B43_BFL2_BTC3WIRE		0x0080	/* used 3-wire bluetooth coexist */
+#define B43_BFL2_SKWRKFEM_BRD		0x0100	/* 4321mcm93 uses Skyworks FEM */
+#define B43_BFL2_SPUR_WAR		0x0200	/* has a workaround for clock-harmonic spurs */
+#define B43_BFL2_GPLL_WAR		0x0400	/* altenative G-band PLL settings implemented */
+#define B43_BFL2_SINGLEANT_CCK		0x1000
+#define B43_BFL2_2G_SPUR_WAR		0x2000
+
+/* SPROM boardflags2_hi values */
+#define B43_BFH2_GPLL_WAR2		0x0001
+#define B43_BFH2_IPALVLSHIFT_3P3	0x0002
+#define B43_BFH2_INTERNDET_TXIQCAL	0x0004
+#define B43_BFH2_XTALBUFOUTEN		0x0008
+
+/* GPIO register offset, in both ChipCommon and PCI core. */
+#define B43_GPIO_CONTROL		0x6c
+
+/* SHM Routing */
+enum {
+	B43