diff options
53 files changed, 1481 insertions, 274 deletions
diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index dbd22e0df21e..b4cd9f906c24 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -19,6 +19,9 @@ Required properties: 4 = active high level-sensitive. 8 = active low level-sensitive. +Optional properties: +- clocks: the clock for clocking the GPIO silicon + Example: gpio0: gpio@73f84000 { diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt new file mode 100644 index 000000000000..ba455589f869 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt @@ -0,0 +1,35 @@ +Mediatek MT7621 SoC GPIO controller bindings + +The IP core used inside these SoCs has 3 banks of 32 GPIOs each. +The registers of all the banks are interwoven inside one single IO range. +We load one GPIO controller instance per bank. Also the GPIO controller can receive +interrupts on any of the GPIOs, either edge or level. It then interrupts the CPU +using GIC INT12. + +Required properties for the top level node: +- #gpio-cells : Should be two. The first cell is the GPIO pin number and the + second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. + Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt. Should be 2. The first cell defines the interrupt number, + the second encodes the triger flags encoded as described in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- compatible: + - "mediatek,mt7621-gpio" for Mediatek controllers +- reg : Physical base address and length of the controller's registers +- interrupt-parent : phandle of the parent interrupt controller. +- interrupts : Interrupt specifier for the controllers interrupt. +- interrupt-controller : Mark the device node as an interrupt controller. +- gpio-controller : Marks the device node as a GPIO controller. + +Example: + gpio@600 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "mediatek,mt7621-gpio"; + gpio-controller; + interrupt-controller; + reg = <0x600 0x100>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 12 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt index c82a2e221bc1..adff16c71d21 100644 --- a/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra186-gpio.txt @@ -68,6 +68,8 @@ Required properties: One of: - "nvidia,tegra186-gpio". - "nvidia,tegra186-gpio-aon". + - "nvidia,tegra194-gpio". + - "nvidia,tegra194-gpio-aon". - reg-names Array of strings. Contains a list of names for the register spaces described by the reg @@ -91,6 +93,8 @@ Required properties: depending on compatible value: - "nvidia,tegra186-gpio": 6 entries. - "nvidia,tegra186-gpio-aon": 1 entry. + - "nvidia,tegra194-gpio": 6 entries. + - "nvidia,tegra194-gpio-aon": 1 entry. - gpio-controller Boolean. Marks the device node as a GPIO controller/provider. diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index fe1bf24104d3..4018ee57a6af 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -17,6 +17,7 @@ Required Properties: - "renesas,gpio-r8a7796": for R8A7796 (R-Car M3-W) compatible GPIO controller. - "renesas,gpio-r8a77965": for R8A77965 (R-Car M3-N) compatible GPIO controller. - "renesas,gpio-r8a77970": for R8A77970 (R-Car V3M) compatible GPIO controller. + - "renesas,gpio-r8a77980": for R8A77980 (R-Car V3H) compatible GPIO controller. - "renesas,gpio-r8a77990": for R8A77990 (R-Car E3) compatible GPIO controller. - "renesas,gpio-r8a77995": for R8A77995 (R-Car D3) compatible GPIO controller. - "renesas,rcar-gen1-gpio": for a generic R-Car Gen1 GPIO controller. diff --git a/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.txt b/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.txt new file mode 100644 index 000000000000..f9231df17c2b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.txt @@ -0,0 +1,32 @@ +Rockchip RK3328 GRF (General Register Files) GPIO controller. + +In Rockchip RK3328, the output only GPIO_MUTE pin, originally for codec mute +control, can also be used for general purpose. It is manipulated by the +GRF_SOC_CON10 register in GRF. Aside from the GPIO_MUTE pin, the HDMI pins can +also be set in the same way. + +Currently this GPIO controller only supports the mute pin. If needed in the +future, the HDMI pins support can also be added. + +Required properties: +- compatible: Should contain "rockchip,rk3328-grf-gpio". +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be 2. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = Active high, + 1 = Active low. + +Example: + + grf: syscon@ff100000 { + compatible = "rockchip,rk3328-grf", "syscon", "simple-mfd"; + + grf_gpio: grf-gpio { + compatible = "rockchip,rk3328-grf-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; + +Note: The grf_gpio node should be declared as the child of the GRF (General +Register File) node. The GPIO_MUTE pin is referred to as <&grf_gpio 0>. diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 71c0ab46f216..f7a0f576f918 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -359,6 +359,15 @@ config GPIO_MPC8XXX Say Y here if you're going to use hardware that connects to the MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs. +config GPIO_MT7621 + bool "Mediatek MT7621 GPIO Support" + depends on SOC_MT7620 || SOC_MT7621 || COMPILE_TEST + depends on OF_GPIO + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + help + Say yes here to support the Mediatek MT7621 SoC GPIO device + config GPIO_MVEBU def_bool y depends on PLAT_ORION || ARCH_MVEBU @@ -684,7 +693,8 @@ config GPIO_IT87 Say yes here to support GPIO functionality of IT87xx Super I/O chips. This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and - supports the IT8761E, IT8620E and IT8628E Super I/O chip as well. + supports the IT8761E, IT8613, IT8620E, and IT8628E Super I/O chips as + well. To compile this driver as a module, choose M here: the module will be called gpio_it87 diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 1324c8f966a7..fc77989371be 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -88,6 +88,7 @@ obj-$(CONFIG_GPIO_MOCKUP) += gpio-mockup.o obj-$(CONFIG_GPIO_MPC5200) += gpio-mpc5200.o obj-$(CONFIG_GPIO_MPC8XXX) += gpio-mpc8xxx.o obj-$(CONFIG_GPIO_MSIC) += gpio-msic.o +obj-$(CONFIG_GPIO_MT7621) += gpio-mt7621.o obj-$(CONFIG_GPIO_MVEBU) += gpio-mvebu.o obj-$(CONFIG_GPIO_MXC) += gpio-mxc.o obj-$(CONFIG_GPIO_MXS) += gpio-mxs.o diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c index b31ae16170e7..2342e154029b 100644 --- a/drivers/gpio/gpio-aspeed.c +++ b/drivers/gpio/gpio-aspeed.c @@ -12,6 +12,7 @@ #include <asm/div64.h> #include <linux/clk.h> #include <linux/gpio/driver.h> +#include <linux/gpio/aspeed.h> #include <linux/hashtable.h> #include <linux/init.h> #include <linux/io.h> @@ -22,6 +23,15 @@ #include <linux/spinlock.h> #include <linux/string.h> +/* + * These two headers aren't meant to be used by GPIO drivers. We need + * them in order to access gpio_chip_hwgpio() which we need to implement + * the aspeed specific API which allows the coprocessor to request + * access to some GPIOs and to arbitrate between coprocessor and ARM. + */ +#include <linux/gpio/consumer.h> +#include "gpiolib.h" + struct aspeed_bank_props { unsigned int bank; u32 input; @@ -56,83 +66,130 @@ struct aspeed_gpio { struct clk *clk; u32 *dcache; + u8 *cf_copro_bankmap; }; struct aspeed_gpio_bank { - uint16_t val_regs; + uint16_t val_regs; /* +0: Rd: read input value, Wr: set write latch + * +4: Rd/Wr: Direction (0=in, 1=out) + */ + uint16_t rdata_reg; /* Rd: read write latch, Wr: <none> */ uint16_t irq_regs; uint16_t debounce_regs; uint16_t tolerance_regs; + uint16_t cmdsrc_regs; const char names[4][3]; }; +/* + * Note: The "value" register returns the input value sampled on the + * line even when the GPIO is configured as an output. Since + * that input goes through synchronizers, writing, then reading + * back may not return the written value right away. + * + * The "rdata" register returns the content of the write latch + * and thus can be used to read back what was last written + * reliably. + */ + static const int debounce_timers[4] = { 0x00, 0x50, 0x54, 0x58 }; +static const struct aspeed_gpio_copro_ops *copro_ops; +static void *copro_data; + static const struct aspeed_gpio_bank aspeed_gpio_banks[] = { { .val_regs = 0x0000, + .rdata_reg = 0x00c0, .irq_regs = 0x0008, .debounce_regs = 0x0040, .tolerance_regs = 0x001c, + .cmdsrc_regs = 0x0060, .names = { "A", "B", "C", "D" }, }, { .val_regs = 0x0020, + .rdata_reg = 0x00c4, .irq_regs = 0x0028, .debounce_regs = 0x0048, .tolerance_regs = 0x003c, + .cmdsrc_regs = 0x0068, .names = { "E", "F", "G", "H" }, }, { .val_regs = 0x0070, + .rdata_reg = 0x00c8, .irq_regs = 0x0098, .debounce_regs = 0x00b0, .tolerance_regs = 0x00ac, + .cmdsrc_regs = 0x0090, .names = { "I", "J", "K", "L" }, }, { .val_regs = 0x0078, + .rdata_reg = 0x00cc, .irq_regs = 0x00e8, .debounce_regs = 0x0100, .tolerance_regs = 0x00fc, + .cmdsrc_regs = 0x00e0, .names = { "M", "N", "O", "P" }, }, { .val_regs = 0x0080, + .rdata_reg = 0x00d0, .irq_regs = 0x0118, .debounce_regs = 0x0130, .tolerance_regs = 0x012c, + .cmdsrc_regs = 0x0110, .names = { "Q", "R", "S", "T" }, }, { .val_regs = 0x0088, + .rdata_reg = 0x00d4, .irq_regs = 0x0148, .debounce_regs = 0x0160, .tolerance_regs = 0x015c, + .cmdsrc_regs = 0x0140, .names = { "U", "V", "W", "X" }, }, { .val_regs = 0x01E0, + .rdata_reg = 0x00d8, .irq_regs = 0x0178, .debounce_regs = 0x0190, .tolerance_regs = 0x018c, + .cmdsrc_regs = 0x0170, .names = { "Y", "Z", "AA", "AB" }, }, { .val_regs = 0x01e8, + .rdata_reg = 0x00dc, .irq_regs = 0x01a8, .debounce_regs = 0x01c0, .tolerance_regs = 0x01bc, + .cmdsrc_regs = 0x01a0, .names = { "AC", "", "", "" }, }, }; -#define GPIO_BANK(x) ((x) >> 5) -#define GPIO_OFFSET(x) ((x) & 0x1f) -#define GPIO_BIT(x) BIT(GPIO_OFFSET(x)) +enum aspeed_gpio_reg { + reg_val, + reg_rdata, + reg_dir, + reg_irq_enable, + reg_irq_type0, + reg_irq_type1, + reg_irq_type2, + reg_irq_status, + reg_debounce_sel1, + reg_debounce_sel2, + reg_tolerance, + reg_cmdsrc0, + reg_cmdsrc1, +}; -#define GPIO_DATA 0x00 -#define GPIO_DIR 0x04 +#define GPIO_VAL_VALUE 0x00 +#define GPIO_VAL_DIR 0x04 #define GPIO_IRQ_ENABLE 0x00 #define GPIO_IRQ_TYPE0 0x04 @@ -143,6 +200,53 @@ static const struct aspeed_gpio_bank aspeed_gpio_banks[] = { #define GPIO_DEBOUNCE_SEL1 0x00 #define GPIO_DEBOUNCE_SEL2 0x04 +#define GPIO_CMDSRC_0 0x00 +#define GPIO_CMDSRC_1 0x04 +#define GPIO_CMDSRC_ARM 0 +#define GPIO_CMDSRC_LPC 1 +#define GPIO_CMDSRC_COLDFIRE 2 +#define GPIO_CMDSRC_RESERVED 3 + +/* This will be resolved at compile time */ +static inline void __iomem *bank_reg(struct aspeed_gpio *gpio, + const struct aspeed_gpio_bank *bank, + const enum aspeed_gpio_reg reg) +{ + switch (reg) { + case reg_val: + return gpio->base + bank->val_regs + GPIO_VAL_VALUE; + case reg_rdata: + return gpio->base + bank->rdata_reg; + case reg_dir: + return gpio->base + bank->val_regs + GPIO_VAL_DIR; + case reg_irq_enable: + return gpio->base + bank->irq_regs + GPIO_IRQ_ENABLE; + case reg_irq_type0: + return gpio->base + bank->irq_regs + GPIO_IRQ_TYPE0; + case reg_irq_type1: + return gpio->base + bank->irq_regs + GPIO_IRQ_TYPE1; + case reg_irq_type2: + return gpio->base + bank->irq_regs + GPIO_IRQ_TYPE2; + case reg_irq_status: + return gpio->base + bank->irq_regs + GPIO_IRQ_STATUS; + case reg_debounce_sel1: + return gpio->base + bank->debounce_regs + GPIO_DEBOUNCE_SEL1; + case reg_debounce_sel2: + return gpio->base + bank->debounce_regs + GPIO_DEBOUNCE_SEL2; + case reg_tolerance: + return gpio->base + bank->tolerance_regs; + case reg_cmdsrc0: + return gpio->base + bank->cmdsrc_regs + GPIO_CMDSRC_0; + case reg_cmdsrc1: + return gpio->base + bank->cmdsrc_regs + GPIO_CMDSRC_1; + } + BUG(); +} + +#define GPIO_BANK(x) ((x) >> 5) +#define GPIO_OFFSET(x) ((x) & 0x1f) +#define GPIO_BIT(x) BIT(GPIO_OFFSET(x)) + #define _GPIO_SET_DEBOUNCE(t, o, i) ((!!((t) & BIT(i))) << GPIO_OFFSET(o)) #define GPIO_SET_DEBOUNCE1(t, o) _GPIO_SET_DEBOUNCE(t, o, 1) #define GPIO_SET_DEBOUNCE2(t, o) _GPIO_SET_DEBOUNCE(t, o, 0) @@ -201,18 +305,80 @@ static inline bool have_output(struct aspeed_gpio *gpio, unsigned int offset) return !props || (props->output & GPIO_BIT(offset)); } -static void __iomem *bank_val_reg(struct aspeed_gpio *gpio, - const struct aspeed_gpio_bank *bank, - unsigned int reg) +static void aspeed_gpio_change_cmd_source(struct aspeed_gpio *gpio, + const struct aspeed_gpio_bank *bank, + int bindex, int cmdsrc) { - return gpio->base + bank->val_regs + reg; + void __iomem *c0 = bank_reg(gpio, bank, reg_cmdsrc0); + void __iomem *c1 = bank_reg(gpio, bank, reg_cmdsrc1); + u32 bit, reg; + + /* + * Each register controls 4 banks, so take the bottom 2 + * bits of the bank index, and use them to select the + * right control bit (0, 8, 16 or 24). + */ + bit = BIT((bindex & 3) << 3); + + /* Source 1 first to avoid illegal 11 combination */ + reg = ioread32(c1); + if (cmdsrc & 2) + reg |= bit; + else + reg &= ~bit; + iowrite32(reg, c1); + + /* Then Source 0 */ + reg = ioread32(c0); + if (cmdsrc & 1) + reg |= bit; + else + reg &= ~bit; + iowrite32(reg, c0); } -static void __iomem *bank_irq_reg(struct aspeed_gpio *gpio, - const struct aspeed_gpio_bank *bank, - unsigned int reg) +static bool aspeed_gpio_copro_request(struct aspeed_gpio *gpio, + unsigned int offset) { - return gpio->base + bank->irq_regs + reg; + const struct aspeed_gpio_bank *bank = to_bank(offset); + + if (!copro_ops || !gpio->cf_copro_bankmap) + return false; + if (!gpio->cf_copro_bankmap[offset >> 3]) + return false; + if (!copro_ops->request_access) + return false; + + /* Pause the coprocessor */ + copro_ops->request_access(copro_data); + + /* Change command source back to ARM */ + aspeed_gpio_change_cmd_source(gpio, bank, offset >> 3, GPIO_CMDSRC_ARM); + + /* Update cache */ + gpio->dcache[GPIO_BANK(offset)] = ioread32(bank_reg(gpio, bank, reg_rdata)); + + return true; +} + +static void aspeed_gpio_copro_release(struct aspeed_gpio *gpio, + unsigned int offset) +{ + const struct aspeed_gpio_bank *bank = to_bank(offset); + + if (!copro_ops || !gpio->cf_copro_bankmap) + return; + if (!gpio->cf_copro_bankmap[offset >> 3]) + return; + if (!copro_ops->release_access) + return; + + /* Change command source back to ColdFire */ + aspeed_gpio_change_cmd_source(gpio, bank, offset >> 3, + GPIO_CMDSRC_COLDFIRE); + + /* Restart the coprocessor */ + copro_ops->release_access(copro_data); } static int aspeed_gpio_get(struct gpio_chip *gc, unsigned int offset) @@ -220,8 +386,7 @@ static int aspeed_gpio_get(struct gpio_chip *gc, unsigned int offset) struct aspeed_gpio *gpio = gpiochip_get_data(gc); const struct aspeed_gpio_bank *bank = to_bank(offset); - return !!(ioread32(bank_val_reg(gpio, bank, GPIO_DATA)) - & GPIO_BIT(offset)); + return !!(ioread32(bank_reg(gpio, bank, reg_val)) & GPIO_BIT(offset)); } static void __aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset, @@ -232,7 +397,7 @@ static void __aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset, void __iomem *addr; u32 reg; - addr = bank_val_reg(gpio, bank, GPIO_DATA); + addr = bank_reg(gpio, bank, reg_val); reg = gpio->dcache[GPIO_BANK(offset)]; if (val) @@ -249,11 +414,15 @@ static void aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset, { struct aspeed_gpio *gpio = gpiochip_get_data(gc); unsigned long flags; + bool copro; spin_lock_irqsave(&gpio->lock, flags); + copro = aspeed_gpio_copro_request(gpio, offset); __aspeed_gpio_set(gc, offset, val); + if (copro) + aspeed_gpio_copro_release(gpio, offset); spin_unlock_irqrestore(&gpio->lock, flags); } @@ -261,7 +430,9 @@ static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset) { struct aspeed_gpio *gpio = gpiochip_get_data(gc); const struct aspeed_gpio_bank *bank = to_bank(offset); + void __iomem *addr = bank_reg(gpio, bank, reg_dir); unsigned long flags; + bool copro; u32 reg; if (!have_input(gpio, offset)) @@ -269,8 +440,13 @@ static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset) spin_lock_irqsave(&gpio->lock, flags); - reg = ioread32(bank_val_reg(gpio, bank, GPIO_DIR)); - iowrite32(reg & ~GPIO_BIT(offset), bank_val_reg(gpio, bank, GPIO_DIR)); + reg = ioread32(addr); + reg &= ~GPIO_BIT(offset); + + copro = aspeed_gpio_copro_request(gpio, offset); + iowrite32(reg, addr); + if (copro) + aspeed_gpio_copro_release(gpio, offset); spin_unlock_irqrestore(&gpio->lock, flags); @@ -282,7 +458,9 @@ static int aspeed_gpio_dir_out(struct gpio_chip *gc, { struct aspeed_gpio *gpio = gpiochip_get_data(gc); const struct aspeed_gpio_bank *bank = to_bank(offset); + void __iomem *addr = bank_reg(gpio, bank, reg_dir); unsigned long flags; + bool copro; u32 reg; if (!have_output(gpio, offset)) @@ -290,10 +468,15 @@ static int aspeed_gpio_dir_out(struct gpio_chip *gc, spin_lock_irqsave(&gpio->lock, flags); + reg = ioread32(addr); + reg |= GPIO_BIT(offset); + + copro = aspeed_gpio_copro_request(gpio, offset); __aspeed_gpio_set(gc, offset, val); - reg = ioread32(bank_val_reg(gpio, bank, GPIO_DIR)); - iowrite32(reg | GPIO_BIT(offset), bank_val_reg(gpio, bank, GPIO_DIR)); + iowrite32(reg, addr); + if (copro) + aspeed_gpio_copro_release(gpio, offset); spin_unlock_irqrestore(&gpio->lock, flags); return 0; @@ -314,7 +497,7 @@ static int aspeed_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) spin_lock_irqsave(&gpio->lock, flags); - val = ioread32(bank_val_reg(gpio, bank, GPIO_DIR)) & GPIO_BIT(offset); + val = ioread32(bank_reg(gpio, bank, reg_dir)) & GPIO_BIT(offset); spin_unlock_irqrestore(&gpio->lock, flags); @@ -323,24 +506,23 @@ static int aspeed_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) } static inline int irqd_to_aspeed_gpio_data(struct irq_data *d, - struct aspeed_gpio **gpio, - const struct aspeed_gpio_bank **bank, - u32 *bit) + struct aspeed_gpio **gpio, + const struct aspeed_gpio_bank **bank, + u32 *bit, int *offset) { - int offset; struct aspeed_gpio *internal; - offset = irqd_to_hwirq(d); + *offset = irqd_to_hwirq(d); internal = irq_data_get_irq_chip_data(d); /* This might be a bit of a questionable place to check */ - if (!have_irq(internal, offset)) + if (!have_irq(internal, *offset)) return -ENOTSUPP; *gpio = internal; - *bank = to_bank(offset); - *bit = GPIO_BIT(offset); + *bank = to_bank(*offset); + *bit = GPIO_BIT(*offset); return 0; } @@ -351,17 +533,23 @@ static void aspeed_gpio_irq_ack(struct irq_data *d) struct aspeed_gpio *gpio; unsigned long flags; void __iomem *status_addr; + int rc, offset; + bool copro; u32 bit; - int rc; - rc = irqd_to_aspeed_gpio_data(d, &gpio, &bank, &bit); + rc = irqd_to_aspeed_gpio_data(d, &gpio, &bank, &bit, &offset); if (rc) return; - status_addr = bank_irq_reg(gpio, bank, GPIO_IRQ_STATUS); + status_addr = bank_reg(gpio, bank, reg_irq_status); |