diff options
60 files changed, 1947 insertions, 2814 deletions
diff --git a/Documentation/devicetree/bindings/leds/maxim,max77693.yaml b/Documentation/devicetree/bindings/leds/maxim,max77693.yaml new file mode 100644 index 000000000000..86a0005cf156 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/maxim,max77693.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/maxim,max77693.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX77693 MicroUSB and Companion Power Management IC LEDs + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> + +description: | + This is a part of device tree bindings for Maxim MAX77693 MicroUSB Integrated + Circuit (MUIC). + + There are two LED outputs available - FLED1 and FLED2. Each of them can + control a separate LED or they can be connected together to double the + maximum current for a single connected LED. One LED is represented by one + child node. + + See also Documentation/devicetree/bindings/mfd/maxim,max77693.yaml for + additional information and example. + +properties: + compatible: + const: maxim,max77693-led + + maxim,boost-mode: + description: + In boost mode the device can produce up to 1.2A of total current on both + outputs. The maximum current on each output is reduced to 625mA then. If + not enabled explicitly, boost setting defaults to LEDS_BOOST_FIXED in + case both current sources are used. + See LEDS_BOOST_* in include/dt-bindings/leds/common.h. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + maxim,boost-mvout: + description: | + Output voltage of the boost module in millivolts. + Valid values: 3300 - 5500, step by 25 (rounded down) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 3300 + maximum: 5500 + default: 3300 + + maxim,mvsys-min: + description: | + Low input voltage level in millivolts. Flash is not fired if chip + estimates that system voltage could drop below this level due to flash + power consumption. + Valid values: 2400 - 3400, step by 33 (rounded down) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2400 + maximum: 3400 + default: 2400 + +patternProperties: + "^([a-z]+-)?led[01]?$": + type: object + $ref: common.yaml# + unevaluatedProperties: false + + properties: + led-sources: + allOf: + - minItems: 1 + maxItems: 2 + items: + minimum: 0 + maximum: 1 + + led-max-microamp: + description: | + Valid values for a LED connected to one FLED output: + 15625 - 250000, step by 15625 (rounded down) + Valid values for a LED connected to both FLED outputs: + 15625 - 500000, step by 15625 (rounded down) + + flash-max-microamp: + description: | + Valid values for a single LED connected to one FLED output + (boost mode must be turned off): + 15625 - 1000000, step by 15625 (rounded down) + Valid values for a single LED connected to both FLED outputs: + 15625 - 1250000, step by 15625 (rounded down) + Valid values for two LEDs case: + 15625 - 625000, step by 15625 (rounded down) + + flash-max-timeout-us: + description: | + Valid values: 62500 - 1000000, step by 62500 (rounded down) + minimum: 62500 + maximum: 1000000 + + required: + - flash-max-microamp + - flash-max-timeout-us + - led-max-microamp + - led-sources + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt deleted file mode 100644 index 937b3e5505e0..000000000000 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ /dev/null @@ -1,282 +0,0 @@ -* AB8500 Multi-Functional Device (MFD) - -Required parent device properties: -- compatible : contains "stericsson,ab8500" or "stericsson,ab8505"; -- interrupts : contains the IRQ line for the AB8500 -- interrupt-controller : describes the AB8500 as an Interrupt Controller (has its own domain) -- #interrupt-cells : should be 2, for 2-cell format - - The first cell is the AB8500 local IRQ number - - The second cell is used to specify optional parameters - - bits[3:0] trigger type and level flags: - 1 = low-to-high edge triggered - 2 = high-to-low edge triggered - 4 = active high level-sensitive - 8 = active low level-sensitive - -The AB8500 consists of a large and varied group of sub-devices: - -Device IRQ Names Supply Names Description ------- --------- ------------ ----------- -ab8500-bm : : : Battery Manager -ab8500-btemp : : : Battery Temperature -ab8500-charger : : : Battery Charger -ab8500-codec : : : Audio Codec -ab8500-fg : : vddadc : Fuel Gauge - : NCONV_ACCU : : Accumulate N Sample Conversion - : BATT_OVV : : Battery Over Voltage - : LOW_BAT_F : : LOW threshold battery voltage - : CC_INT_CALIB : : Coulomb Counter Internal Calibration - : CCEOC : : Coulomb Counter End of Conversion -ab8500-btemp : : vtvout : Battery Temperature - : BAT_CTRL_INDB : : Battery Removal Indicator - : BTEMP_LOW : : Btemp < BtempLow, if battery temperature is lower than -10°C - : BTEMP_LOW_MEDIUM : : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C - : BTEMP_MEDIUM_HIGH : : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and MaxTemp - : BTEMP_HIGH : : Btemp > BtempHigh, if battery temperature is higher than MaxTemp -ab8500-charger : : vddadc : Charger interface - : MAIN_CH_UNPLUG_DET : : main charger unplug detection management (not in 8505) - : MAIN_CHARGE_PLUG_DET : : main charger plug detection management (not in 8505) - : MAIN_EXT_CH_NOT_OK : : main charger not OK - : MAIN_CH_TH_PROT_R : : Die temp is above main charger - : MAIN_CH_TH_PROT_F : : Die temp is below main charger - : VBUS_DET_F : : VBUS falling detected - : VBUS_DET_R : : VBUS rising detected - : USB_LINK_STATUS : : USB link status has changed - : USB_CH_TH_PROT_R : : Die temp is above usb charger - : USB_CH_TH_PROT_F : : Die temp is below usb charger - : USB_CHARGER_NOT_OKR : : allowed USB charger not ok detection - : VBUS_OVV : : Overvoltage on Vbus ball detected (USB charge is stopped) - : CH_WD_EXP : : Charger watchdog detected -ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter - SW_CONV_END : : -ab8500-gpio : : : GPIO Controller (AB8500) -ab8505-gpio : : : GPIO Controller (AB8505) -ab8500-ponkey : ONKEY_DBF : : Power-on Key - ONKEY_DBR : : -ab8500-pwm : : : Pulse Width Modulator -ab8500-regulator : : : Regulators (AB8500) -ab8505-regulator : : : Regulators (AB8505) -ab8500-rtc : 60S : : Real Time Clock - : ALARM : : -ab8500-sysctrl : : : System Control -ab8500-usb : ID_WAKEUP_R : vddulpivio18 : Universal Serial Bus - : ID_WAKEUP_F : v-ape : - : VBUS_DET_F : musb_1v8 : - : VBUS_DET_R : : - : USB_LINK_STATUS : : - : USB_ADP_PROBE_PLUG : : - : USB_ADP_PROBE_UNPLUG : : - -Required child device properties: -- compatible : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey| - pwm|regulator|rtc|sysctrl|usb]"; - - A few child devices require ADC channels from the GPADC node. Those follow the - standard bindings from - https://github.com/devicetree-org/dt-schema/blob/master/schemas/iio/iio-consumer.yaml - and Documentation/devicetree/bindings/iio/adc/adc.yaml - - abx500-temp : io-channels "aux1" and "aux2" for measuring external - temperatures. - ab8500-fg : io-channel "main_bat_v" for measuring main battery voltage, - ab8500-btemp : io-channels "btemp_ball" and "bat_ctrl" for measuring the - battery voltage. - ab8500-charger : io-channels "main_charger_v", "main_charger_c", "vbus_v", - "usb_charger_c" for measuring voltage and current of the - different charging supplies. - -Optional child device properties: -- interrupts : contains the device IRQ(s) using the 2-cell format (see above) -- interrupt-names : contains names of IRQ resource in the order in which they were - supplied in the interrupts property -- <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree - -Non-standard child device properties: - - Audio CODEC: - - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential) - - stericsson,amic1a-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic - - stericsson,amic1b-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic - - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic - - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) - -ab8500 { - compatible = "stericsson,ab8500"; - interrupts = <0 40 0x4>; - interrupt-controller; - #interrupt-cells = <2>; - - ab8500-rtc { - compatible = "stericsson,ab8500-rtc"; - interrupts = <17 0x4 - 18 0x4>; - interrupt-names = "60S", "ALARM"; - }; - - ab8500-gpadc { - compatible = "stericsson,ab8500-gpadc"; - interrupts = <32 0x4 - 39 0x4>; - interrupt-names = "HW_CONV_END", "SW_CONV_END"; - vddadc-supply = <&ab8500_ldo_tvout_reg>; - #address-cells = <1>; - #size-cells = <0>; - #io-channel-cells = <1>; - - /* GPADC channels */ - bat_ctrl: channel@1 { - reg = <0x01>; - }; - btemp_ball: channel@2 { - reg = <0x02>; - }; - main_charger_v: channel@3 { - reg = <0x03>; - }; - acc_detect1: channel@4 { - reg = <0x04>; - }; - acc_detect2: channel@5 { - reg = <0x05>; - }; - adc_aux1: channel@6 { - reg = <0x06>; - }; - adc_aux2: channel@7 { - reg = <0x07>; - }; - main_batt_v: channel@8 { - reg = <0x08>; - }; - vbus_v: channel@9 { - reg = <0x09>; - }; - main_charger_c: channel@a { - reg = <0x0a>; - }; - usb_charger_c: channel@b { - reg = <0x0b>; - }; - bk_bat_v: channel@c { - reg = <0x0c>; - }; - die_temp: channel@d { - reg = <0x0d>; - }; - usb_id: channel@e { - reg = <0x0e>; - }; - xtal_temp: channel@12 { - reg = <0x12>; - }; - vbat_true_meas: channel@13 { - reg = <0x13>; - }; - bat_ctrl_and_ibat: channel@1c { - reg = <0x1c>; - }; - vbat_meas_and_ibat: channel@1d { - reg = <0x1d>; - }; - vbat_true_meas_and_ibat: channel@1e { - reg = <0x1e>; - }; - bat_temp_and_ibat: channel@1f { - reg = <0x1f>; - }; - }; - - ab8500_temp { - compatible = "stericsson,abx500-temp"; - io-channels = <&gpadc 0x06>, - <&gpadc 0x07>; - io-channel-name = "aux1", "aux2"; - }; - - ab8500_battery: ab8500_battery { - stericsson,battery-type = "LIPO"; - thermistor-on-batctrl; - }; - - ab8500_fg { - compatible = "stericsson,ab8500-fg"; - battery = <&ab8500_battery>; - io-channels = <&gpadc 0x08>; - io-channel-name = "main_bat_v"; - }; - - ab8500_btemp { - compatible = "stericsson,ab8500-btemp"; - battery = <&ab8500_battery>; - io-channels = <&gpadc 0x02>, - <&gpadc 0x01>; - io-channel-name = "btemp_ball", - "bat_ctrl"; - }; - - ab8500_charger { - compatible = "stericsson,ab8500-charger"; - battery = <&ab8500_battery>; - vddadc-supply = <&ab8500_ldo_tvout_reg>; - io-channels = <&gpadc 0x03>, - <&gpadc 0x0a>, - <&gpadc 0x09>, - <&gpadc 0x0b>; - io-channel-name = "main_charger_v", - "main_charger_c", - "vbus_v", - "usb_charger_c"; - }; - - ab8500-usb { - compatible = "stericsson,ab8500-usb"; - interrupts = < 90 0x4 - 96 0x4 - 14 0x4 - 15 0x4 - 79 0x4 - 74 0x4 - 75 0x4>; - interrupt-names = "ID_WAKEUP_R", - "ID_WAKEUP_F", - "VBUS_DET_F", - "VBUS_DET_R", - "USB_LINK_STATUS", - "USB_ADP_PROBE_PLUG", - "USB_ADP_PROBE_UNPLUG"; - vddulpivio18-supply = <&ab8500_ldo_intcore_reg>; - v-ape-supply = <&db8500_vape_reg>; - musb_1v8-supply = <&db8500_vsmps2_reg>; - }; - - ab8500-ponkey { - compatible = "stericsson,ab8500-ponkey"; - interrupts = <6 0x4 - 7 0x4>; - interrupt-names = "ONKEY_DBF", "ONKEY_DBR"; - }; - - ab8500-sysctrl { - compatible = "stericsson,ab8500-sysctrl"; - }; - - ab8500-pwm { - compatible = "stericsson,ab8500-pwm"; - }; - - codec: ab8500-codec { - compatible = "stericsson,ab8500-codec"; - - stericsson,earpeice-cmv = <950>; /* Units in mV. */ - }; - - ab8500-regulators { - compatible = "stericsson,ab8500-regulator"; - - ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { - /* - * See: Documentation/devicetree/bindings/regulator/regulator.txt - * for more information on regulators - */ - }; - }; -}; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt deleted file mode 100644 index 1032df14498b..000000000000 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ /dev/null @@ -1,194 +0,0 @@ -Maxim MAX77693 multi-function device - -MAX77693 is a Multifunction device with the following submodules: -- PMIC, -- CHARGER, -- LED, -- MUIC, -- HAPTIC - -It is interfaced to host controller using i2c. -This document describes the bindings for the mfd device. - -Required properties: -- compatible : Must be "maxim,max77693". -- reg : Specifies the i2c slave address of PMIC block. -- interrupts : This i2c device has an IRQ line connected to the main SoC. - -Optional properties: -- regulators : The regulators of max77693 have to be instantiated under subnode - named "regulators" using the following format. - - regulators { - regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER - standard regulator constraints[*]. - }; - - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - -- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide - users with tactile feedback. PWM period and duty-cycle are varied in - order to provide the appropriate level of feedback. - - Required properties: - - compatible : Must be "maxim,max77693-haptic" - - haptic-supply : power supply for the haptic motor - [*] refer Documentation/devicetree/bindings/regulator/regulator.txt - - pwms : phandle to the physical PWM(Pulse Width Modulation) device. - PWM properties should be named "pwms". And number of cell is different - for each pwm device. - To get more information, please refer to documentation. - [*] refer Documentation/devicetree/bindings/pwm/pwm.txt - -- charger : Node configuring the charger driver. - If present, required properties: - - compatible : Must be "maxim,max77693-charger". - - Optional properties (if not set, defaults will be used): - - maxim,constant-microvolt : Battery constant voltage in uV. The charger - will operate in fast charge constant current mode till battery voltage - reaches this level. Then the charger will switch to fast charge constant - voltage mode. Also vsys (system voltage) will be set to this value when - DC power is supplied but charger is not enabled. - Valid values: 3650000 - 4400000, step by 25000 (rounded down) - Default: 4200000 - - - maxim,min-system-microvolt : Minimal system voltage in uV. - Valid values: 3000000 - 3700000, step by 100000 (rounded down) - Default: 3600000 - - - maxim,thermal-regulation-celsius : Temperature in Celsius for entering - high temperature charging mode. If die temperature exceeds this value - the charging current will be reduced by 105 mA/Celsius. - Valid values: 70, 85, 100, 115 - Default: 100 - - - maxim,battery-overcurrent-microamp : Overcurrent protection threshold - in uA (current from battery to system). - Valid values: 2000000 - 3500000, step by 250000 (rounded down) - Default: 3500000 - - - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for - triggering input voltage regulation loop. If input voltage decreases - below this value, the input current will be reduced to reach the - threshold voltage. - Valid values: 4300000, 4700000, 4800000, 4900000 - Default: 4300000 - -- led : the LED submodule device node - -There are two LED outputs available - FLED1 and FLED2. Each of them can -control a separate LED or they can be connected together to double -the maximum current for a single connected LED. One LED is represented -by one child node. - -Required properties: -- compatible : Must be "maxim,max77693-led". - -Optional properties: -- maxim,boost-mode : - In boost mode the device can produce up to 1.2A of total current - on both outputs. The maximum current on each output is reduced - to 625mA then. If not enabled explicitly, boost setting defaults to - LEDS_BOOST_FIXED in case both current sources are used. - Possible values: - LEDS_BOOST_OFF (0) - no boost, |