diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml | 199 |
1 files changed, 195 insertions, 4 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml index 69408cae3db9..ab5881d0d017 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml @@ -14,6 +14,11 @@ description: | https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-16.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-18.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7607.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7608.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7609.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf properties: @@ -24,11 +29,27 @@ properties: - adi,ad7606-6 - adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet - adi,ad7606b + - adi,ad7606c-16 + - adi,ad7606c-18 + - adi,ad7607 + - adi,ad7608 + - adi,ad7609 - adi,ad7616 reg: maxItems: 1 + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + # According to the datasheet, "Data is clocked in from SDI on the falling + # edge of SCLK, while data is clocked out on DOUTA on the rising edge of + # SCLK". Also, even if not stated textually in the datasheet, it is made + # clear on the diagrams that sclk idles at high. Subsequently, in case SPI + # interface is used, the correct way is to only set spi-cpol. spi-cpha: true spi-cpol: true @@ -114,18 +135,91 @@ properties: assumed that the pins are hardwired to VDD. type: boolean + pwms: + description: + In case the conversion is triggered by a PWM instead of a GPIO plugged to + the CONVST pin, the PWM must be referenced. + The first is the PWM connected to CONVST or CONVST1 for the chips with the + 2nd PWM connected to CONVST2, if CONVST2 is available and not shorted to + CONVST1. + minItems: 1 + maxItems: 2 + + pwm-names: + items: + - const: convst1 + - const: convst2 + + io-backends: + description: + A reference to the iio-backend, which is responsible handling the BUSY + pin's falling edge and communication. + An example of backend can be found at + http://analogdevicesinc.github.io/hdl/library/axi_ad7606x/index.html + + +patternProperties: + "^channel@[1-8]$": + type: object + $ref: adc.yaml + unevaluatedProperties: false + + properties: + reg: + description: + The channel number, as specified in the datasheet (from 1 to 8). + minimum: 1 + maximum: 8 + + diff-channels: + description: + Each channel can be configured as a bipolar differential channel. + The ADC uses the same positive and negative inputs for this. + This property must be specified as 'reg' (or the channel number) for + both positive and negative inputs (i.e. diff-channels = <reg reg>). + Since the configuration is bipolar differential, the 'bipolar' + property is required. + items: + minimum: 1 + maximum: 8 + + bipolar: + description: + The ADC channels can be configured as + * Bipolar single-ended + * Unipolar single-ended + * Bipolar differential + Therefore in the DT, if no channel node is specified, it is considered + 'unipolar single-ended'. So for the other configurations the 'bipolar' + property must be specified. If 'diff-channels' is specified, it is + considered a bipolar differential channel. Otherwise it is bipolar + single-ended. + + required: + - reg + - bipolar + required: - compatible - reg - - spi-cpha - avcc-supply - vdrive-supply - - interrupts - - adi,conversion-start-gpios allOf: - $ref: /schemas/spi/spi-peripheral-props.yaml# + - oneOf: + - required: + - adi,conversion-start-gpios + - required: + - pwms + + - oneOf: + - required: + - interrupts + - required: + - io-backends + - if: properties: compatible: @@ -162,19 +256,68 @@ allOf: - adi,ad7606-4 - adi,ad7606-6 - adi,ad7606-8 + - adi,ad7607 + - adi,ad7608 + - adi,ad7609 then: properties: adi,sw-mode: false else: properties: + pwms: + maxItems: 1 + pwm-names: + maxItems: 1 adi,conversion-start-gpios: maxItems: 1 + - if: + not: + required: + - adi,sw-mode + then: + patternProperties: + "^channel@[1-8]$": false + + - if: + not: + properties: + compatible: + enum: + - adi,ad7606c-16 + - adi,ad7606c-18 + then: + patternProperties: + "^channel@[1-8]$": false + unevaluatedProperties: false examples: - | #include <dt-bindings/gpio/gpio.h> + iio-backend { + #address-cells = <1>; + #size-cells = <0>; + adi_adc@0 { + compatible = "adi,ad7606b"; + reg = <0>; + pwms = <&axi_pwm_gen 0 0>; + + avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; + + reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>; + adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH + &gpio0 87 GPIO_ACTIVE_HIGH + &gpio0 86 GPIO_ACTIVE_HIGH>; + io-backends = <&iio_backend>; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> spi { #address-cells = <1>; @@ -185,7 +328,6 @@ examples: reg = <0>; spi-max-frequency = <1000000>; spi-cpol; - spi-cpha; avcc-supply = <&adc_vref>; vdrive-supply = <&vdd_supply>; @@ -202,4 +344,53 @@ examples: standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; }; }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7606c-18"; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + + adi,sw-mode; + + channel@1 { + reg = <1>; + diff-channels = <1 1>; + bipolar; + }; + + channel@3 { + reg = <3>; + bipolar; + }; + + channel@8 { + reg = <8>; + diff-channels = <8 8>; + bipolar; + }; + + }; + }; ... |