diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
23 files changed, 1311 insertions, 78 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/adc.yaml b/Documentation/devicetree/bindings/iio/adc/adc.yaml index 8e7835cf36fd..b9bc02b5b07a 100644 --- a/Documentation/devicetree/bindings/iio/adc/adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adc.yaml @@ -37,6 +37,10 @@ properties: to both the positive and negative inputs of a differential ADC. The first value specifies the positive input pin, the second specifies the negative input pin. + There are also some ADCs, where the differential channel has dedicated + positive and negative inputs which can be used to measure differential + voltage levels. For those setups, this property can be configured with + the 'reg' property for both inputs (i.e. diff-channels = <reg reg>). single-channel: $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7173.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7173.yaml index 17c5d39cc2c1..ad15cf9bc2ff 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7173.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7173.yaml @@ -28,6 +28,7 @@ description: | Datasheets for supported chips: https://www.analog.com/media/en/technical-documentation/data-sheets/AD4111.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD4112.pdf + <AD4113: not released yet> https://www.analog.com/media/en/technical-documentation/data-sheets/AD4114.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD4115.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD4116.pdf @@ -44,6 +45,7 @@ properties: enum: - adi,ad4111 - adi,ad4112 + - adi,ad4113 - adi,ad4114 - adi,ad4115 - adi,ad4116 @@ -331,6 +333,7 @@ allOf: enum: - adi,ad4111 - adi,ad4112 + - adi,ad4113 - adi,ad4114 - adi,ad4115 - adi,ad4116 diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml index 0065d6508824..ada08005b3cd 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml @@ -25,6 +25,8 @@ description: | * https://www.analog.com/en/products/ad7386-4.html * https://www.analog.com/en/products/ad7387-4.html * https://www.analog.com/en/products/ad7388-4.html + * https://www.analog.com/en/products/adaq4370-4.html + * https://www.analog.com/en/products/adaq4380-4.html $ref: /schemas/spi/spi-peripheral-props.yaml# @@ -46,6 +48,8 @@ properties: - adi,ad7386-4 - adi,ad7387-4 - adi,ad7388-4 + - adi,adaq4370-4 + - adi,adaq4380-4 reg: maxItems: 1 @@ -70,6 +74,20 @@ properties: refin-supply: description: A 2.5V to 3.3V supply for external reference voltage, for ad7380-4 only. + For adaq devices, a 5V supply voltage. A 3.3V internal reference is + derived from it. Connect to vs-p-supply for normal operation. + + vs-p-supply: + description: + Amplifiers positive supply. + + vs-n-supply: + description: + Amplifiers negative supply. + + ldo-supply: + description: + LDO supply. Connect to vs-p-supply or a 3.6 to 5.5 V supply. aina-supply: description: @@ -97,12 +115,45 @@ properties: specify the ALERT interrupt. maxItems: 1 + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + required: - compatible - reg - vcc-supply - vlogic-supply +patternProperties: + "^channel@[0-3]$": + $ref: adc.yaml + type: object + + properties: + reg: + description: + The channel number. From 0 to 3 corresponding to channels A,B,C,D + minimum: 0 + maximum: 3 + + adi,gain-milli: + description: + The hardware gain applied to the ADC input (in milli units). + If not present, default to 1000 (no actual gain applied). + Refer to the typical connection diagrams section of the datasheet for + pin wiring. + $ref: /schemas/types.yaml#/definitions/uint16 + enum: [300, 600, 1000, 1600] + default: 1000 + + required: + - reg + + additionalProperties: false + unevaluatedProperties: false allOf: @@ -140,6 +191,7 @@ allOf: aind-supply: false # ad7380-4 uses refin-supply as external reference. + # adaq devices use internal reference only, derived from refin-supply # All other chips from ad738x family use refio as optional external reference. # When refio-supply is omitted, internal reference is used. - if: @@ -147,6 +199,8 @@ allOf: compatible: enum: - adi,ad7380-4 + - adi,adaq4370-4 + - adi,adaq4380-4 then: properties: refio-supply: false @@ -156,6 +210,27 @@ allOf: properties: refin-supply: false + # adaq devices need more supplies and using channel to declare gain property + # only applies to adaq devices + - if: + properties: + compatible: + enum: + - adi,adaq4370-4 + - adi,adaq4380-4 + then: + required: + - vs-p-supply + - vs-n-supply + - ldo-supply + else: + properties: + vs-p-supply: false + vs-n-supply: false + ldo-supply: false + patternProperties: + "^channel@[0-3]$": false + examples: - | #include <dt-bindings/interrupt-controller/irq.h> @@ -180,3 +255,48 @@ examples: refio-supply = <&supply_2_5V>; }; }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,adaq4380-4"; + reg = <0>; + + spi-cpol; + spi-cpha; + spi-max-frequency = <80000000>; + + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio0>; + + vcc-supply = <&supply_3_3V>; + vlogic-supply = <&supply_3_3V>; + refin-supply = <&supply_5V>; + vs-p-supply = <&supply_5V>; + vs-n-supply = <&supply_0V>; + ldo-supply = <&supply_5V>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + adi,gain-milli = /bits/ 16 <300>; + }; + + channel@2 { + reg = <2>; + adi,gain-milli = /bits/ 16 <600>; + }; + + channel@3 { + reg = <3>; + adi,gain-milli = /bits/ 16 <1000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml index 69408cae3db9..ab5881d0d017 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml @@ -14,6 +14,11 @@ description: | https://www.analog.com/media/en/technical-documentation/data-sheets/AD7605-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-16.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606c-18.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7607.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7608.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7609.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf properties: @@ -24,11 +29,27 @@ properties: - adi,ad7606-6 - adi,ad7606-8 # Referred to as AD7606 (without -8) in the datasheet - adi,ad7606b + - adi,ad7606c-16 + - adi,ad7606c-18 + - adi,ad7607 + - adi,ad7608 + - adi,ad7609 - adi,ad7616 reg: maxItems: 1 + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + # According to the datasheet, "Data is clocked in from SDI on the falling + # edge of SCLK, while data is clocked out on DOUTA on the rising edge of + # SCLK". Also, even if not stated textually in the datasheet, it is made + # clear on the diagrams that sclk idles at high. Subsequently, in case SPI + # interface is used, the correct way is to only set spi-cpol. spi-cpha: true spi-cpol: true @@ -114,18 +135,91 @@ properties: assumed that the pins are hardwired to VDD. type: boolean + pwms: + description: + In case the conversion is triggered by a PWM instead of a GPIO plugged to + the CONVST pin, the PWM must be referenced. + The first is the PWM connected to CONVST or CONVST1 for the chips with the + 2nd PWM connected to CONVST2, if CONVST2 is available and not shorted to + CONVST1. + minItems: 1 + maxItems: 2 + + pwm-names: + items: + - const: convst1 + - const: convst2 + + io-backends: + description: + A reference to the iio-backend, which is responsible handling the BUSY + pin's falling edge and communication. + An example of backend can be found at + http://analogdevicesinc.github.io/hdl/library/axi_ad7606x/index.html + + +patternProperties: + "^channel@[1-8]$": + type: object + $ref: adc.yaml + unevaluatedProperties: false + + properties: + reg: + description: + The channel number, as specified in the datasheet (from 1 to 8). + minimum: 1 + maximum: 8 + + diff-channels: + description: + Each channel can be configured as a bipolar differential channel. + The ADC uses the same positive and negative inputs for this. + This property must be specified as 'reg' (or the channel number) for + both positive and negative inputs (i.e. diff-channels = <reg reg>). + Since the configuration is bipolar differential, the 'bipolar' + property is required. + items: + minimum: 1 + maximum: 8 + + bipolar: + description: + The ADC channels can be configured as + * Bipolar single-ended + * Unipolar single-ended + * Bipolar differential + Therefore in the DT, if no channel node is specified, it is considered + 'unipolar single-ended'. So for the other configurations the 'bipolar' + property must be specified. If 'diff-channels' is specified, it is + considered a bipolar differential channel. Otherwise it is bipolar + single-ended. + + required: + - reg + - bipolar + required: - compatible - reg - - spi-cpha - avcc-supply - vdrive-supply - - interrupts - - adi,conversion-start-gpios allOf: - $ref: /schemas/spi/spi-peripheral-props.yaml# + - oneOf: + - required: + - adi,conversion-start-gpios + - required: + - pwms + + - oneOf: + - required: + - interrupts + - required: + - io-backends + - if: properties: compatible: @@ -162,19 +256,68 @@ allOf: - adi,ad7606-4 - adi,ad7606-6 - adi,ad7606-8 + - adi,ad7607 + - adi,ad7608 + - adi,ad7609 then: properties: adi,sw-mode: false else: properties: + pwms: + maxItems: 1 + pwm-names: + maxItems: 1 adi,conversion-start-gpios: maxItems: 1 + - if: + not: + required: + - adi,sw-mode + then: + patternProperties: + "^channel@[1-8]$": false + + - if: + not: + properties: + compatible: + enum: + - adi,ad7606c-16 + - adi,ad7606c-18 + then: + patternProperties: + "^channel@[1-8]$": false + unevaluatedProperties: false examples: - | #include <dt-bindings/gpio/gpio.h> + iio-backend { + #address-cells = <1>; + #size-cells = <0>; + adi_adc@0 { + compatible = "adi,ad7606b"; + reg = <0>; + pwms = <&axi_pwm_gen 0 0>; + + avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; + + reset-gpios = <&gpio0 91 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>; + adi,range-gpios = <&gpio0 89 GPIO_ACTIVE_HIGH>; + adi,oversampling-ratio-gpios = <&gpio0 88 GPIO_ACTIVE_HIGH + &gpio0 87 GPIO_ACTIVE_HIGH + &gpio0 86 GPIO_ACTIVE_HIGH>; + io-backends = <&iio_backend>; + }; + }; + + - | + #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> spi { #address-cells = <1>; @@ -185,7 +328,6 @@ examples: reg = <0>; spi-max-frequency = <1000000>; spi-cpol; - spi-cpha; avcc-supply = <&adc_vref>; vdrive-supply = <&vdd_supply>; @@ -202,4 +344,53 @@ examples: standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; }; }; + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7606c-18"; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + spi-max-frequency = <1000000>; + spi-cpol; + + avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; + + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + + adi,sw-mode; + + channel@1 { + reg = <1>; + diff-channels = <1 1>; + bipolar; + }; + + channel@3 { + reg = <3>; + bipolar; + }; + + channel@8 { + reg = <8>; + diff-channels = <8 8>; + bipolar; + }; + + }; + }; ... diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7625.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7625.yaml new file mode 100644 index 000000000000..8848562af28f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7625.yaml @@ -0,0 +1,176 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7625.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices Fast PulSAR Analog to Digital Converters + +maintainers: + - Michael Hennerich <Michael.Hennerich@analog.com> + - Nuno Sá <nuno.sa@analog.com> + +description: | + A family of single channel differential analog to digital converters. + + * https://www.analog.com/en/products/ad7625.html + * https://www.analog.com/en/products/ad7626.html + * https://www.analog.com/en/products/ad7960.html + * https://www.analog.com/en/products/ad7961.html + +properties: + compatible: + enum: + - adi,ad7625 + - adi,ad7626 + - adi,ad7960 + - adi,ad7961 + + vdd1-supply: true + vdd2-supply: true + vio-supply: true + + ref-supply: + description: + Voltage regulator for the external reference voltage (REF). + + refin-supply: + description: + Voltage regulator for the reference buffer input (REFIN). + + clocks: + description: + The clock connected to the CLK pins, gated by the clk_gate PWM. + maxItems: 1 + + pwms: + items: + - description: PWM connected to the CNV input on the ADC. + - description: PWM that gates the clock connected to the ADC's CLK input. + + pwm-names: + items: + - const: cnv + - const: clk_gate + + io-backends: + description: + The AXI ADC IP block connected to the D+/- and DCO+/- lines of the + ADC. An example backend can be found at + http://analogdevicesinc.github.io/hdl/projects/pulsar_lvds/index.html. + maxItems: 1 + + adi,no-dco: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates the wiring of the DCO+/- lines. If true, then they are + grounded and the device is in self-clocked mode. If this is not + present, then the device is in echoed clock mode. + + adi,en0-always-on: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if EN0 is hard-wired to the high state. If neither this + nor en0-gpios are present, then EN0 is hard-wired low. + + adi,en1-always-on: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if EN1 is hard-wired to the high state. If neither this + nor en1-gpios are present, then EN1 is hard-wired low. + + adi,en2-always-on: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if EN2 is hard-wired to the high state. If neither this + nor en2-gpios are present, then EN2 is hard-wired low. + + adi,en3-always-on: + $ref: /schemas/types.yaml#/definitions/flag + description: + Indicates if EN3 is hard-wired to the high state. If neither this + nor en3-gpios are present, then EN3 is hard-wired low. + + en0-gpios: + description: + Configurable EN0 pin. + + en1-gpios: + description: + Configurable EN1 pin. + + en2-gpios: + description: + Configurable EN2 pin. + + en3-gpios: + description: + Configurable EN3 pin. + +required: + - compatible + - vdd1-supply + - vdd2-supply + - vio-supply + - clocks + - pwms + - pwm-names + - io-backends + +allOf: + - if: + required: + - ref-supply + then: + properties: + refin-supply: false + - if: + required: + - refin-supply + then: + properties: + ref-supply: false + - if: + properties: + compatible: + contains: + enum: + - adi,ad7625 + - adi,ad7626 + then: + properties: + en2-gpios: false + en3-gpios: false + adi,en2-always-on: false + adi,en3-always-on: false + + - if: + properties: + compatible: + contains: + enum: + - adi,ad7960 + - adi,ad7961 + then: + # ad796x parts must have one of the two supplies + oneOf: + - required: [ref-supply] + - required: [refin-supply] + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + adc { + compatible = "adi,ad7625"; + vdd1-supply = <&supply_5V>; + vdd2-supply = <&supply_2_5V>; + vio-supply = <&supply_2_5V>; + io-backends = <&axi_adc>; + clocks = <&ref_clk>; + pwms = <&axi_pwm_gen 0 0>, <&axi_pwm_gen 1 0>; + pwm-names = "cnv", "clk_gate"; + en0-gpios = <&gpio0 86 GPIO_ACTIVE_HIGH>; + en1-gpios = <&gpio0 87 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml new file mode 100644 index 000000000000..044f92f39cfa --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7779.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7779.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD777X family 8-Channel, 24-Bit, Simultaneous Sampling ADCs + +maintainers: + - Ramona Nechita <ramona.nechita@analog.com> + +description: | + The AD777X family consist of 8-channel, simultaneous sampling analog-to- + digital converter (ADC). Eight full Σ-Δ ADCs are on-chip. The + AD7771 provides an ultralow input current to allow direct sensor + connection. Each input channel has a programmable gain stage + allowing gains of 1, 2, 4, and 8 to map lower amplitude sensor + outputs into the full-scale ADC input range, maximizing the + dynamic range of the signal chain. + + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7770.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7771.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad7779.pdf + +$ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + enum: + - adi,ad7770 + - adi,ad7771 + - adi,ad7779 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + clocks: + maxItems: 1 + + avdd1-supply: + description: Front-End analog supply AVDD1. Can be used as conversion ref. + + avdd2-supply: + description: AVDD2 Analog Supply from 2.2 V to 3.6 V. + + avdd4-supply: + description: AVDD4 SAR Analog Supply and Reference Source. + + interrupts: + minItems: 1 + items: + - description: | + adc_rdy: Interrupt line for DRDY signal which indicates the end of + conversion independently of the interface selected to read back the + Σ-∆ conversion. + - description: | + Alert: The chip includes self diagnostic features to guarantee the + correct operation. If an error is detected, the ALERT pin is pulled + high to generate an external interruption to the controller. + + interrupt-names: + minItems: 1 + maxItems: 2 + items: + enum: + - adc_rdy + - alert + + start-gpios: + description: + Pin that controls start synchronization pulse. + maxItems: 1 + + reset-gpios: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7779"; + reg = <0>; + start-gpios = <&gpio0 87 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio0 93 GPIO_ACTIVE_LOW>; + interrupt-parent = <&intc>; + interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "adc_rdy"; + clocks = <&adc_clk>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.yaml b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.yaml index f748f3a60b35..b0962a4583ac 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.yaml @@ -98,6 +98,7 @@ allOf: compatible: contains: enum: + - amlogic,meson8-saradc - amlogic,meson8b-saradc - amlogic,meson8m2-saradc then: diff --git a/Documentation/devicetree/bindings/iio/adc/gehc,pmc-adc.yaml b/Documentation/devicetree/bindings/iio/adc/gehc,pmc-adc.yaml new file mode 100644 index 000000000000..2cea7c104a26 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/gehc,pmc-adc.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/gehc,pmc-adc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GE HealthCare PMC Analog to Digital Converter (ADC) + +maintainers: + - Herve Codina <herve.codina@bootlin.com> + +description: + The GE HealthCare PMC ADC is a 16-Channel (voltage and current), 16-Bit ADC + with an I2C Interface. + +properties: + compatible: + const: gehc,pmc-adc + + reg: + maxItems: 1 + + vdd-supply: + description: + Regulator for the VDD power supply. + + vdda-supply: + description: + Regulator for the VDD analog (VDDA) power supply. + + vddio-supply: + description: + Regulator for the VDD IO (VDDIO) power supply. + + vref-supply: + description: + Regulator for the voltage reference power supply. + + clocks: + maxItems: 1 + description: + The component uses an external oscillator (osc) if an external oscillator + is connected to its clock pins. Otherwise, it uses an internal reference + clock. + + clock-names: + items: + - const: osc + + "#io-channel-cells": + const: 2 + description: | + The first cell is the channel type (dt-bindings/iio/adc/gehc,pmc-adc.h + defines these values): + - 0: voltage + - 1: current + The second cell |