| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ice_qp_dis() currently does things in very mixed way. Tx is stopped
before disabling IRQ on related queue vector, then it takes care of
disabling Rx and finally NAPI is disabled.
Let us start with disabling IRQs in the first place followed by turning
off NAPI. Then it is safe to handle queues.
One subtle change on top of that is that even though ice_qp_ena() looks
more sane, clear ICE_CFG_BUSY as the last thing there.
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Disable NAPI before shutting down queues that this particular NAPI
contains so that the order of actions in i40e_queue_pair_disable()
mirrors what we do in i40e_queue_pair_enable().
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently routines that are supposed to toggle state of ring pair do not
take care of associated interrupt with queue vector that these rings
belong to. This causes funky issues such as dead interface due to irq
misconfiguration, as per Pavel's report from Closes: tag.
Add a function responsible for disabling single IRQ in EIMC register and
call this as a very first thing when disabling ring pair during xsk_pool
setup. For enable let's reuse ixgbe_irq_enable_queues(). Besides this,
disable/enable NAPI as first/last thing when dealing with closing or
opening ring pair that xsk_pool is being configured on.
Reported-by: Pavel Vazharov <pavel@x3me.net>
Closes: https://lore.kernel.org/netdev/CAJEV1ijxNyPTwASJER1bcZzS9nMoZJqfR86nu_3jFFVXzZQ4NA@mail.gmail.com/
Fixes: 024aa5800f32 ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Limit the WiFi PCIe link speed to Gen2 speed (500 MB/s), which is the
speed that the boot firmware has brought up the link at (and that
Windows uses).
This is specifically needed to avoid a large amount of link errors when
restarting the link during boot (but which are currently not reported).
This also appears to fix intermittent failures to download the ath11k
firmware during boot which can be seen when there is a longer delay
between restarting the link and loading the WiFi driver (e.g. when using
full disk encryption).
Fixes: 123b30a75623 ("arm64: dts: qcom: sc8280xp-x13s: enable WiFi controller")
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240223152124.20042-8-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Limit the WiFi PCIe link speed to Gen2 speed (500 MB/s), which is the
speed that Windows uses.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240223152124.20042-7-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
iommu_sva_bind_device will directly goto out in multi-device
case when found existing domain, ignoring list_add handle,
which causes the handle to fail to be shared.
Fixes: 65d4418c5002 ("iommu/sva: Restore SVA handle sharing")
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240227064821.128-1-zhangfei.gao@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
My recent commit e5d00aaac651 ("selftests/powerpc: Check all FPRs in
fpu_preempt") inadvertently broke the fpu_signal test.
It needs to take into account that fpu_preempt now loads 32 FPRs, so
enlarge darray.
Also use the newly added randomise_darray() to properly randomise darray.
Finally the checking done in signal_fpu_sig() needs to skip checking
f30/f31, because they are used as scratch registers in check_all_fprs(),
called by preempt_fpu(), and so could hold other values when the signal
is taken.
Fixes: e5d00aaac651 ("selftests/powerpc: Check all FPRs in fpu_preempt")
Reported-by: Spoorthy <spoorthy@linux.ibm.com>
Depends-on: 2ba107f6795d ("selftests/powerpc: Generate better bit patterns for FPU tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240301101035.1230024-1-mpe@ellerman.id.au
|
|
In azx_probe_codecs function, when bus->codec_mask is becomes to 0(no codecs),
execute azx_init_chip, bus->codec_mask will be initialized to a value again,
this causes snd_hda_codec_new function to run, the process is as follows:
-->snd_hda_codec_new
-->snd_hda_codec_device_init
-->snd_hdac_device_init---snd_hdac_read_parm(...AC_PAR_VENDOR_ID) 2s
---snd_hdac_read_parm(...AC_PAR_VENDOR_ID) 2s
---snd_hdac_read_parm(...AC_PAR_SUBSYSTEM_ID) 2s
---snd_hdac_read_parm(...AC_PAR_REV_ID) 2s
---snd_hdac_read_parm(...AC_PAR_NODE_COUNT) 2s
when no codecs, read communication is error, each command will be polled for
2 second, a total of 10s, it is easy to some problem.
like this:
2 [ 14.833404][ 6] [ T164] hda 0006:00: Codec #0 probe error; disabling it...
3 [ 14.844178][ 6] [ T164] hda 0006:00: codec_mask = 0x1
4 [ 14.880532][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0000
5 [ 15.891988][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0000
6 [ 16.978090][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0001
7 [ 18.140895][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0002
8 [ 19.135516][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0004
10 [ 19.900086][ 6] [ T164] hda 0006:00: no codecs initialized
11 [ 45.573398][ 2] [ C2] watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [kworker/2:0:25]
Here, when bus->codec_mask is 0, use a direct break to avoid execute snd_hda_codec_new function.
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://lore.kernel.org/r/20240301011841.7247-1-soxiebing@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
platform
Headset Mic will no show at resume back.
This patch will fix this issue.
Fixes: d7f32791a9fc ("ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4713d48a372e47f98bba0c6120fd8254@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The unprepare call must be carried out before the finalize call
as the latter can free the request.
Fixes: c66c17a0f69b ("crypto: rk3288 - Remove prepare/unprepare request")
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add myself as co-maintainer for Socionext netsec driver.
This commit also removes Jassi from maintainer since he
no longer has a Developerbox.
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is now possible to disable BQL, but that causes the cpsw driver to break:
drivers/net/ethernet/ti/am65-cpsw-nuss.c:297:28: error: no member named 'dql' in 'struct netdev_queue'
297 | dql_avail(&netif_txq->dql),
There is already a helper function in net/sch_generic.h that could
be used to help here. Move its implementation into the common
linux/netdevice.h along with the other bql interfaces and change
both users over to the new interface.
Fixes: ea7f3cfaa588 ("net: bql: allow the config to be disabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current driver has some asymmetry in the runtime PM calls. On lan78xx_open()
it will call usb_autopm_get() and unconditionally usb_autopm_put(). And
on lan78xx_stop() it will call only usb_autopm_put(). So far, it was
working only because this driver do not activate autosuspend by default,
so it was visible only by warning "Runtime PM usage count underflow!".
Since, with current driver, we can't use runtime PM with active link,
execute lan78xx_open()->usb_autopm_put() only in error case. Otherwise,
keep ref counting high as long as interface is open.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current method for signaling the compatibility of a Hyper-V host
with MSIs featuring 15-bit APIC IDs relies on a synthetic cpuid leaf.
However, for higher VTLs, this leaf is not reported, due to the absence
of an IO-APIC.
As an alternative, assume that when running at a high VTL, the host
supports 15-bit APIC IDs. This assumption is safe, as Hyper-V does not
employ any architectural MSIs at higher VTLs
This unblocks startup of VTL2 environments with more than 256 CPUs.
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/1705341460-18394-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1705341460-18394-1-git-send-email-ssengar@linux.microsoft.com>
|
|
Hogs are added *after* ACPI so should be removed *before* in error path.
Fixes: a411e81e61df ("gpiolib: add hogs support for machine code")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The internal delay properties are not mandatory and should have a
documented default value. The device only supports either no delay or a
fixed delay and the device reset default is no delay, document the
default as no delay.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a CoCo VM, when transitioning memory from encrypted to decrypted, or
vice versa, the caller of set_memory_encrypted() or set_memory_decrypted()
is responsible for ensuring the memory isn't in use and isn't referenced
while the transition is in progress. The transition has multiple steps,
and the memory is in an inconsistent state until all steps are complete.
A reference while the state is inconsistent could result in an exception
that can't be cleanly fixed up.
However, the kernel load_unaligned_zeropad() mechanism could cause a stray
reference that can't be prevented by the caller of set_memory_encrypted()
or set_memory_decrypted(), so there's specific code to handle this case.
But a CoCo VM running on Hyper-V may be configured to run with a paravisor,
with the #VC or #VE exception routed to the paravisor. There's no
architectural way to forward the exceptions back to the guest kernel, and
in such a case, the load_unaligned_zeropad() specific code doesn't work.
To avoid this problem, mark pages as "not present" while a transition
is in progress. If load_unaligned_zeropad() causes a stray reference, a
normal page fault is generated instead of #VC or #VE, and the
page-fault-based fixup handlers for load_unaligned_zeropad() resolve the
reference. When the encrypted/decrypted transition is complete, mark the
pages as "present" again.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/r/20240116022008.1023398-4-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240116022008.1023398-4-mhklinux@outlook.com>
|
|
set_memory_p() is currently static. It has parameters that don't
match set_memory_p() under arch/powerpc and that aren't congruent
with the other set_memory_* functions. There's no good reason for
the difference.
Fix this by making the parameters consistent, and update the one
existing call site. Make the function non-static and add it to
include/asm/set_memory.h so that it is completely parallel to
set_memory_np() and is usable in other modules.
No functional change.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20240116022008.1023398-3-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240116022008.1023398-3-mhklinux@outlook.com>
|
|
In preparation for temporarily marking pages not present during a
transition between encrypted and decrypted, use slow_virt_to_phys()
in the hypervisor callback. As long as the PFN is correct,
slow_virt_to_phys() works even if the leaf PTE is not present.
The existing functions that depend on vmalloc_to_page() all
require that the leaf PTE be marked present, so they don't work.
Update the comments for slow_virt_to_phys() to note this broader usage
and the requirement to work even if the PTE is not marked present.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Link: https://lore.kernel.org/r/20240116022008.1023398-2-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240116022008.1023398-2-mhklinux@outlook.com>
|
|
Add documentation topic for PCI pass-thru devices in Linux guests
on Hyper-V and for the associated PCI controller driver (pci-hyperv.c).
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Link: https://lore.kernel.org/r/20240222200710.305259-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240222200710.305259-1-mhklinux@outlook.com>
|
|
A previous commit left the indentation in create_gpadl_header()
unchanged for ease of review. Update the indentation and remove
line wrap in two places where it is no longer necessary.
No functional change.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240111165451.269418-2-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240111165451.269418-2-mhklinux@outlook.com>
|
|
create_gpadl_header() creates a message header, and one or more message
bodies if the number of GPADL entries exceeds what fits in the
header. Currently the code for creating the message header is
duplicated in the two halves of the main "if" statement governing
whether message bodies are created.
Eliminate the duplication by making minor tweaks to the logic and
associated comments. While here, simplify the handling of memory
allocation errors, and use umin() instead of open coding it.
For ease of review, the indentation of sizable chunks of code is
*not* changed. A follow-on patch updates only the indentation.
No functional change.
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240111165451.269418-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240111165451.269418-1-mhklinux@outlook.com>
|
|
A recent commit removing the use of screen_info introduced a logic
error. The error causes hvfb_getmem() to always return -ENOMEM
for Generation 2 VMs. As a result, the Hyper-V frame buffer
device fails to initialize. The error was introduced by removing
an "else if" clause, leaving Gen2 VMs to always take the -ENOMEM
error path.
Fix the problem by removing the error path "else" clause. Gen 2
VMs now always proceed through the MMIO memory allocation code,
but with "base" and "size" defaulting to 0.
Fixes: 0aa0838c84da ("fbdev/hyperv_fb: Remove firmware framebuffers with aperture helpers")
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Link: https://lore.kernel.org/r/20240201060022.233666-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240201060022.233666-1-mhklinux@outlook.com>
|
|
The VMBUS_RING_SIZE macro adds space for a ring buffer header to the
requested ring buffer size. The header size is always 1 page, and so
its size varies based on the PAGE_SIZE for which the kernel is built.
If the requested ring buffer size is a large power-of-2 size and the header
size is small, the resulting size is inefficient in its use of memory.
For example, a 512 Kbyte ring buffer with a 4 Kbyte page size results in
a 516 Kbyte allocation, which is rounded to up 1 Mbyte by the memory
allocator, and wastes 508 Kbytes of memory.
In such situations, the exact size of the ring buffer isn't that important,
and it's OK to allocate the 4 Kbyte header at the beginning of the 512
Kbytes, leaving the ring buffer itself with just 508 Kbytes. The memory
allocation can be 512 Kbytes instead of 1 Mbyte and nothing is wasted.
Update VMBUS_RING_SIZE to implement this approach for "large" ring buffer
sizes. "Large" is somewhat arbitrarily defined as 8 times the size of
the ring buffer header (which is of size PAGE_SIZE). For example, for
4 Kbyte PAGE_SIZE, ring buffers of 32 Kbytes and larger use the first
4 Kbytes as the ring buffer header. For 64 Kbyte PAGE_SIZE, ring buffers
of 512 Kbytes and larger use the first 64 Kbytes as the ring buffer
header. In both cases, smaller sizes add space for the header so
the ring size isn't reduced too much by using part of the space for
the header. For example, with a 64 Kbyte page size, we don't want
a 128 Kbyte ring buffer to be reduced to 64 Kbytes by allocating half
of the space for the header. In such a case, the memory allocation
is less efficient, but it's the best that can be done.
While the new algorithm slightly changes the amount of space allocated
for ring buffers by drivers that use VMBUS_RING_SIZE, the devices aren't
known to be sensitive to small changes in ring buffer size, so there
shouldn't be any effect.
Fixes: c1135c7fd0e9 ("Drivers: hv: vmbus: Introduce types of GPADL")
Fixes: 6941f67ad37d ("hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218502
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/20240229004533.313662-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240229004533.313662-1-mhklinux@outlook.com>
|
|
Hyper-V hosts can omit the _SYNC flag to due a bug on resume from modern
suspend. In such a case, the guest may fail to update its time-of-day to
account for the period when it was suspended, and could proceed with a
significantly wrong time-of-day. In such a case when the guest is
significantly behind, fix it by treating a _SAMPLE the same as if _SYNC
was received so that the guest time-of-day is updated.
This is hidden behind param hv_utils.timesync_implicit.
Signed-off-by: Peter Martincic <pmartincic@microsoft.com>
Acked-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lore.kernel.org/r/20231127213524.52783-1-pmartincic@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20231127213524.52783-1-pmartincic@linux.microsoft.com>
|
|
After shuffling the code, error path wasn't updated correctly.
Fix it here.
Fixes: 2f4133bb5f14 ("gpiolib: No need to call gpiochip_remove_pin_ranges() twice")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property)
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1]
Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2]
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Nouveau deallocates a few buffers post GPU init which are required for GPU suspend/resume to function correctly.
This is likely not as big an issue on systems where the NVGPU is the only GPU, but on multi-GPU set ups it leads to a regression where the kernel module errors and results in a system-wide rendering freeze.
This commit addresses that regression by moving the two buffers required for suspend and resume to be deallocated at driver unload instead of post init.
Fixes: 042b5f83841fb ("drm/nouveau: fix several DMA buffer leaks")
Signed-off-by: Sid Pranjale <sidpranjale127@protonmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Turns out usage is always in bytes not shifted.
Fixes: 72fa02fdf833 ("nouveau: add an ioctl to report vram usage")
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.8-2024-02-29:
amdgpu:
- Fix potential buffer overflow
- Fix power min cap
- Suspend/resume fix
- SI PM fix
- eDP fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229152424.6646-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.8-rc7
DP:
- Revert a change which was causing a HDP regression
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvhWvHiPGQ1pRD2XPAQoHEM2M35kjhrsSAEtzh8AMSRvg@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
UAPI Changes:
- A couple of tracepoint updates from Priyanka and Lucas.
- Make sure BINDs are completed before accepting UNBINDs on LR vms.
- Don't arbitrarily restrict max number of batched binds.
- Add uapi for dumpable bos (agreed on IRC).
- Remove unused uapi flags and a leftover comment.
Driver Changes:
- A couple of fixes related to the execlist backend.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZeCBg4MA2hd1oggN@fedora
|
|
https://anongit.freedesktop.org/git/drm/drm-misc into drm-fixes
A reset fix for host1x, a resource leak fix and a probe fix for aux-hpd,
a use-after-free fix and a boot fix for a pmic_glink qcom driver in
drivers/soc, a fix for the simpledrm/tegra transition, a kunit fix for
the TTM tests, a font handling fix for fbcon, two allocation fixes and a
kunit test to cover them for drm/buddy
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229-angelic-adorable-teal-fbfabb@houat
|
|
Fix to allocate fprobe::entry_data_size buffer with rethook instances.
If fprobe doesn't allocate entry_data_size buffer for each rethook instance,
fprobe entry handler can cause a buffer overrun when storing entry data in
entry handler.
Link: https://lore.kernel.org/all/170920576727.107552.638161246679734051.stgit@devnote2/
Reported-by: Jiri Olsa <olsajiri@gmail.com>
Closes: https://lore.kernel.org/all/Zd9eBn2FTQzYyg7L@krava/
Fixes: 4bbd93455659 ("kprobes: kretprobe scalability improvement")
Cc: stable@vger.kernel.org
Tested-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
When creating a snapshot we may do a double free of an anonymous device
in case there's an error committing the transaction. The second free may
result in freeing an anonymous device number that was allocated by some
other subsystem in the kernel or another btrfs filesystem.
The steps that lead to this:
1) At ioctl.c:create_snapshot() we allocate an anonymous device number
and assign it to pending_snapshot->anon_dev;
2) Then we call btrfs_commit_transaction() and end up at
transaction.c:create_pending_snapshot();
3) There we call btrfs_get_new_fs_root() and pass it the anonymous device
number stored in pending_snapshot->anon_dev;
4) btrfs_get_new_fs_root() frees that anonymous device number because
btrfs_lookup_fs_root() returned a root - someone else did a lookup
of the new root already, which could some task doing backref walking;
5) After that some error happens in the transaction commit path, and at
ioctl.c:create_snapshot() we jump to the 'fail' label, and after
that we free again the same anonymous device number, which in the
meanwhile may have been reallocated somewhere else, because
pending_snapshot->anon_dev still has the same value as in step 1.
Recently syzbot ran into this and reported the following trace:
------------[ cut here ]------------
ida_free called for id=51 which is not allocated.
WARNING: CPU: 1 PID: 31038 at lib/idr.c:525 ida_free+0x370/0x420 lib/idr.c:525
Modules linked in:
CPU: 1 PID: 31038 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00410-gc02197fc9076 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
RIP: 0010:ida_free+0x370/0x420 lib/idr.c:525
Code: 10 42 80 3c 28 (...)
RSP: 0018:ffffc90015a67300 EFLAGS: 00010246
RAX: be5130472f5dd000 RBX: 0000000000000033 RCX: 0000000000040000
RDX: ffffc90009a7a000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: ffffc90015a673f0 R08: ffffffff81577992 R09: 1ffff92002b4cdb4
R10: dffffc0000000000 R11: fffff52002b4cdb5 R12: 0000000000000246
R13: dffffc0000000000 R14: ffffffff8e256b80 R15: 0000000000000246
FS: 00007fca3f4b46c0(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f167a17b978 CR3: 000000001ed26000 CR4: 0000000000350ef0
Call Trace:
<TASK>
btrfs_get_root_ref+0xa48/0xaf0 fs/btrfs/disk-io.c:1346
create_pending_snapshot+0xff2/0x2bc0 fs/btrfs/transaction.c:1837
create_pending_snapshots+0x195/0x1d0 fs/btrfs/transaction.c:1931
btrfs_commit_transaction+0xf1c/0x3740 fs/btrfs/transaction.c:2404
create_snapshot+0x507/0x880 fs/btrfs/ioctl.c:848
btrfs_mksubvol+0x5d0/0x750 fs/btrfs/ioctl.c:998
btrfs_mksnapshot+0xb5/0xf0 fs/btrfs/ioctl.c:1044
__btrfs_ioctl_snap_create+0x387/0x4b0 fs/btrfs/ioctl.c:1306
btrfs_ioctl_snap_create_v2+0x1ca/0x400 fs/btrfs/ioctl.c:1393
btrfs_ioctl+0xa74/0xd40
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0xfe/0x170 fs/ioctl.c:857
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7fca3e67dda9
Code: 28 00 00 00 (...)
RSP: 002b:00007fca3f4b40c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fca3e7abf80 RCX: 00007fca3e67dda9
RDX: 00000000200005c0 RSI: 0000000050009417 RDI: 0000000000000003
RBP: 00007fca3e6ca47a R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fca3e7abf80 R15: 00007fff6bf95658
</TASK>
Where we get an explicit message where we attempt to free an anonymous
device number that is not currently allocated. It happens in a different
code path from the example below, at btrfs_get_root_ref(), so this change
may not fix the case triggered by syzbot.
To fix at least the code path from the example above, change
btrfs_get_root_ref() and its callers to receive a dev_t pointer argument
for the anonymous device number, so that in case it frees the number, it
also resets it to 0, so that up in the call chain we don't attempt to do
the double free.
CC: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/linux-btrfs/000000000000f673a1061202f630@google.com/
Fixes: e03ee2fe873e ("btrfs: do not ASSERT() if the newly created subvolume already got read")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When FIEMAP_FLAG_SYNC is given to fiemap the expectation is that that
are no concurrent writes and we get a stable view of the inode's extent
layout.
When the flag is given we flush all IO (and wait for ordered extents to
complete) and then lock the inode in shared mode, however that leaves open
the possibility that a write might happen right after the flushing and
before locking the inode. So fix this by flushing again after locking the
inode - we leave the initial flushing before locking the inode to avoid
holding the lock and blocking other RO operations while waiting for IO
and ordered extents to complete. The second flushing while holding the
inode's lock will most of the time do nothing or very little since the
time window for new writes to have happened is small.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
For fiemap we recently stopped locking the target extent range for the
whole duration of the fiemap call, in order to avoid a deadlock in a
scenario where the fiemap buffer happens to be a memory mapped range of
the same file. This use case is very unlikely to be useful in practice but
it may be triggered by fuzz testing (syzbot, etc).
However by not locking the target extent range for the whole duration of
the fiemap call we can race with an ordered extent. This happens like
this:
1) The fiemap task finishes processing a file extent item that covers
the file range [512K, 1M[, and that file extent item is the last item
in the leaf currently being processed;
2) And ordered extent for the file range [768K, 2M[, in COW mode,
completes (btrfs_finish_one_ordered()) and the file extent item
covering the range [512K, 1M[ is trimmed to cover the range
[512K, 768K[ and then a new file extent item for the range [768K, 2M[
is inserted in the inode's subvolume tree;
3) The fiemap task calls fiemap_next_leaf_item(), which then calls
btrfs_next_leaf() to find the next leaf / item. This finds that the
the next key following the one we previously processed (its type is
BTRFS_EXTENT_DATA_KEY and its offset is 512K), is the key corresponding
to the new file extent item inserted by the ordered extent, which has
a type of BTRFS_EXTENT_DATA_KEY and an offset of 768K;
4) Later the fiemap code ends up at emit_fiemap_extent() and triggers
the warning:
if (cache->offset + cache->len > offset) {
WARN_ON(1);
return -EINVAL;
}
Since we get 1M > 768K, because the previously emitted entry for the
old extent covering the file range [512K, 1M[ ends at an offset that
is greater than the new extent's start offset (768K). This makes fiemap
fail with -EINVAL besides triggering the warning that produces a stack
trace like the following:
[1621.677651] ------------[ cut here ]------------
[1621.677656] WARNING: CPU: 1 PID: 204366 at fs/btrfs/extent_io.c:2492 emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.677899] Modules linked in: btrfs blake2b_generic (...)
[1621.677951] CPU: 1 PID: 204366 Comm: pool Not tainted 6.8.0-rc5-btrfs-next-151+ #1
[1621.677954] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[1621.677956] RIP: 0010:emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678033] Code: 2b 4c 89 63 (...)
[1621.678035] RSP: 0018:ffffab16089ffd20 EFLAGS: 00010206
[1621.678037] RAX: 00000000004fa000 RBX: ffffab16089ffe08 RCX: 0000000000009000
[1621.678039] RDX: 00000000004f9000 RSI: 00000000004f1000 RDI: ffffab16089ffe90
[1621.678040] RBP: 00000000004f9000 R08: 0000000000001000 R09: 0000000000000000
[1621.678041] R10: 0000000000000000 R11: 0000000000001000 R12: 0000000041d78000
[1621.678043] R13: 0000000000001000 R14: 0000000000000000 R15: ffff9434f0b17850
[1621.678044] FS: 00007fa6e20006c0(0000) GS:ffff943bdfa40000(0000) knlGS:0000000000000000
[1621.678046] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1621.678048] CR2: 00007fa6b0801000 CR3: 000000012d404002 CR4: 0000000000370ef0
[1621.678053] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[1621.678055] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[1621.678056] Call Trace:
[1621.678074] <TASK>
[1621.678076] ? __warn+0x80/0x130
[1621.678082] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678159] ? report_bug+0x1f4/0x200
[1621.678164] ? handle_bug+0x42/0x70
[1621.678167] ? exc_invalid_op+0x14/0x70
[1621.678170] ? asm_exc_invalid_op+0x16/0x20
[1621.678178] ? emit_fiemap_extent+0x84/0x90 [btrfs]
[1621.678253] extent_fiemap+0x766/0xa30 [btrfs]
[1621.678339] btrfs_fiemap+0x45/0x80 [btrfs]
[1621.678420] do_vfs_ioctl+0x1e4/0x870
[1621.678431] __x64_sys_ioctl+0x6a/0xc0
[1621.678434] do_syscall_64+0x52/0x120
[1621.678445] entry_SYSCALL_64_after_hwframe+0x6e/0x76
There's also another case where before calling btrfs_next_leaf() we are
processing a hole or a prealloc extent and we had several delalloc ranges
within that hole or prealloc extent. In that case if the ordered extents
complete before we find the next key, we may end up finding an extent item
with an offset smaller than (or equals to) the offset in cache->offset.
So fix this by changing emit_fiemap_extent() to address these three
scenarios like this:
1) For the first case, steps listed above, adjust the length of the
previously cached extent so that it does not overlap with the current
extent, emit the previous one and cache the current file extent item;
2) For the second case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range,
and the current file extent item has an offset that matches the offset
in the fiemap cache, just discard what we have in the fiemap cache and
assign the current file extent item to the cache, since it's more up
to date;
3) For the third case where he had a hole or prealloc extent with
multiple delalloc ranges inside the hole or prealloc extent's range
and the offset of the file extent item we just found is smaller than
what we have in the cache, just skip the current file extent item
if its range end at or behind the cached extent's end, because we may
have emitted (to the fiemap user space buffer) delalloc ranges that
overlap with the current file extent item's range. If the file extent
item's range goes beyond the end offset of the cached extent, just
emit the cached extent and cache a subrange of the file extent item,
that goes from the end offset of the cached extent to the end offset
of the file extent item.
Dealing with those cases in those ways makes everything consistent by
reflecting the current state of file extent items in the btree and
without emitting extents that have overlapping ranges (which would be
confusing and violating expectations).
This issue could be triggered often with test case generic/561, and was
also hit and reported by Wang Yugui.
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20240223104619.701F.409509F4@e16-tech.com/
Fixes: b0ad381fa769 ("btrfs: fix deadlock with fiemap and extent locking")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, WiFi and netfilter.
We have one outstanding issue with the stmmac driver, which may be a
LOCKDEP false positive, not a blocker.
Current release - regressions:
- netfilter: nf_tables: re-allow NFPROTO_INET in
nft_(match/target)_validate()
- eth: ionic: fix error handling in PCI reset code
Current release - new code bugs:
- eth: stmmac: complete meta data only when enabled, fix null-deref
- kunit: fix again checksum tests on big endian CPUs
Previous releases - regressions:
- veth: try harder when allocating queue memory
- Bluetooth:
- hci_bcm4377: do not mark valid bd_addr as invalid
- hci_event: fix handling of HCI_EV_IO_CAPA_REQUEST
Previous releases - always broken:
- info leak in __skb_datagram_iter() on netlink socket
- mptcp:
- map v4 address to v6 when destroying subflow
- fix potential wake-up event loss due to sndbuf auto-tuning
- fix double-free on socket dismantle
- wifi: nl80211: reject iftype change with mesh ID change
- fix small out-of-bound read when validating netlink be16/32 types
- rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
- ipv6: fix potential "struct net" ref-leak in inet6_rtm_getaddr()
- ip_tunnel: prevent perpetual headroom growth with huge number of
tunnels on top of each other
- mctp: fix skb leaks on error paths of mctp_local_output()
- eth: ice: fixes for DPLL state reporting
- dpll: rely on rcu for netdev_dpll_pin() to prevent UaF
- eth: dpaa: accept phy-interface-type = '10gbase-r' in the device
tree"
* tag 'net-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
dpll: fix build failure due to rcu_dereference_check() on unknown type
kunit: Fix again checksum tests on big endian CPUs
tls: fix use-after-free on failed backlog decryption
tls: separate no-async decryption request handling from async
tls: fix peeking with sync+async decryption
tls: decrement decrypt_pending if no async completion will be called
gtp: fix use-after-free and null-ptr-deref in gtp_newlink()
net: hsr: Use correct offset for HSR TLV values in supervisory HSR frames
igb: extend PTP timestamp adjustments to i211
rtnetlink: fix error logic of IFLA_BRIDGE_FLAGS writing back
tools: ynl: fix handling of multiple mcast groups
selftests: netfilter: add bridge conntrack + multicast test case
netfilter: bridge: confirm multicast packets before passing them up the stack
netfilter: nf_tables: allow NFPROTO_INET in nft_(match/target)_validate()
Bluetooth: qca: Fix triggering coredump implementation
Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT
Bluetooth: qca: Fix wrong event type for patch config command
Bluetooth: Enforce validation on max value of connection interval
Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
Bluetooth: mgmt: Fix limited discoverable off timeout
...
|
|
The update_cpumask(), checks for newly requested cpumask by calling
validate_change(), which returns an error on passing an invalid set
of cpu(s). Independent of the error returned, update_cpumask() always
returns zero, suppressing the error and returning success to the user
on writing an invalid cpu range for a cpuset. Fix it by returning
retval instead, which is returned by validate_change().
Fixes: 99fe36ba6fc1 ("cgroup/cpuset: Improve temporary cpumasks handling")
Signed-off-by: Kamalesh Babulal <kamalesh.babulal@oracle.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull Landlock fix from Mickaël Salaün:
"Fix a potential issue when handling inodes with inconsistent
properties"
* tag 'landlock-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Fix asymmetric private inodes referring
|
|
Offset vmemmap so that the first page of vmemmap will be mapped
to the first page of physical memory in order to ensure that
vmemmap’s bounds will be respected during
pfn_to_page()/page_to_pfn() operations.
The conversion macros will produce correct SV39/48/57 addresses
for every poss |
