summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2022-02-01rxrpc: Adjust retransmission backoffDavid Howells2-6/+4
[ Upstream commit 2c13c05c5ff4b9fc907b07f7311821910ebaaf8a ] Improve retransmission backoff by only backing off when we retransmit data packets rather than when we set the lost ack timer. To this end: (1) In rxrpc_resend(), use rxrpc_get_rto_backoff() when setting the retransmission timer and only tell it that we are retransmitting if we actually have things to retransmit. Note that it's possible for the retransmission algorithm to race with the processing of a received ACK, so we may see no packets needing retransmission. (2) In rxrpc_send_data_packet(), don't bump the backoff when setting the ack_lost_at timer, as it may then get bumped twice. With this, when looking at one particular packet, the retransmission intervals were seen to be 1.5ms, 2ms, 3ms, 5ms, 9ms, 17ms, 33ms, 71ms, 136ms, 264ms, 544ms, 1.088s, 2.1s, 4.2s and 8.3s. Fixes: c410bf01933e ("rxrpc: Fix the excessive initial retransmission timeout") Suggested-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/164138117069.2023386.17446904856843997127.stgit@warthog.procyon.org.uk/ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01octeontx2-pf: Forward error codes to VFSubbaraya Sundeep1-1/+6
[ Upstream commit a8db854be28622a2477cb21cdf7f829adbb2c42d ] PF forwards its VF messages to AF and corresponding replies from AF to VF. AF sets proper error code in the replies after processing message requests. Currently PF checks the error codes in replies and sends invalid message to VF. This way VF lacks the information of error code set by AF for its messages. This patch changes that such that PF simply forwards AF replies so that VF can handle error codes. Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01phylib: fix potential use-after-freeMarek Behún1-3/+3
[ Upstream commit cbda1b16687580d5beee38273f6241ae3725960c ] Commit bafbdd527d56 ("phylib: Add device reset GPIO support") added call to phy_device_reset(phydev) after the put_device() call in phy_detach(). The comment before the put_device() call says that the phydev might go away with put_device(). Fix potential use-after-free by calling phy_device_reset() before put_device(). Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01net: phy: broadcom: hook up soft_reset for BCM54616SRobert Hancock1-0/+1
[ Upstream commit d15c7e875d44367005370e6a82e8f3a382a04f9b ] A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which is a 1 Gbps copper module operating in SGMII mode with an internal BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the module would work properly on the initial insertion or boot of the device, but after the device was rebooted, the link would either only come up at 100 Mbps speeds or go up and down erratically. I found no meaningful changes in the PHY configuration registers between the working and non-working boots, but the status registers seemed to have a lot of error indications set on the SERDES side of the device on the non-working boot. I suspect the problem is that whatever happens on the SGMII link when the device is rebooted and the FPGA logic gets reloaded ends up putting the module's onboard PHY into a bad state. Since commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") the genphy_soft_reset call is not made automatically by the PHY core unless the callback is explicitly specified in the driver structure. For most of these Broadcom devices, there is probably a hardware reset that gets asserted to reset the PHY during boot, however for SFP modules (where the BCM54616S is commonly found) no such reset line exists, so if the board keeps the SFP cage powered up across a reboot, it will end up with no reset occurring during reboots. Hook up the genphy_soft_reset callback for BCM54616S to ensure that a PHY reset is performed before the device is initialized. This appears to fix the issue with erratic operation after a reboot with this SFP module. Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01sched/pelt: Relax the sync of util_sum with util_avgVincent Guittot2-4/+16
[ Upstream commit 98b0d890220d45418cfbc5157b3382e6da5a12ab ] Rick reported performance regressions in bugzilla because of cpu frequency being lower than before: https://bugzilla.kernel.org/show_bug.cgi?id=215045 He bisected the problem to: commit 1c35b07e6d39 ("sched/fair: Ensure _sum and _avg values stay consistent") This commit forces util_sum to be synced with the new util_avg after removing the contribution of a task and before the next periodic sync. By doing so util_sum is rounded to its lower bound and might lost up to LOAD_AVG_MAX-1 of accumulated contribution which has not yet been reflected in util_avg. Instead of always setting util_sum to the low bound of util_avg, which can significantly lower the utilization of root cfs_rq after propagating the change down into the hierarchy, we revert the change of util_sum and propagate the difference. In addition, we also check that cfs's util_sum always stays above the lower bound for a given util_avg as it has been observed that sched_entity's util_sum is sometimes above cfs one. Fixes: 1c35b07e6d39 ("sched/fair: Ensure _sum and _avg values stay consistent") Reported-by: Rick Yiu <rickyiu@google.com> Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Tested-by: Sachin Sant <sachinp@linux.ibm.com> Link: https://lkml.kernel.org/r/20220111134659.24961-2-vincent.guittot@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01perf: Fix perf_event_read_local() timePeter Zijlstra2-112/+149
[ Upstream commit 09f5e7dc7ad705289e1b1ec065439aa3c42951c4 ] Time readers that cannot take locks (due to NMI etc..) currently make use of perf_event::shadow_ctx_time, which, for that event gives: time' = now + (time - timestamp) or, alternatively arranged: time' = time + (now - timestamp) IOW, the progression of time since the last time the shadow_ctx_time was updated. There's problems with this: A) the shadow_ctx_time is per-event, even though the ctx_time it reflects is obviously per context. The direct concequence of this is that the context needs to iterate all events all the time to keep the shadow_ctx_time in sync. B) even with the prior point, the context itself might not be active meaning its time should not advance to begin with. C) shadow_ctx_time isn't consistently updated when ctx_time is There are 3 users of this stuff, that suffer differently from this: - calc_timer_values() - perf_output_read() - perf_event_update_userpage() /* A */ - perf_event_read_local() /* A,B */ In particular, perf_output_read() doesn't suffer at all, because it's sample driven and hence only relevant when the event is actually running. This same was supposed to be true for perf_event_update_userpage(), after all self-monitoring implies the context is active *HOWEVER*, as per commit f79256532682 ("perf/core: fix userpage->time_enabled of inactive events") this goes wrong when combined with counter overcommit, in that case those events that do not get scheduled when the context becomes active (task events typically) miss out on the EVENT_TIME update and ENABLED time is inflated (for a little while) with the time the context was inactive. Once the event gets rotated in, this gets corrected, leading to a non-monotonic timeflow. perf_event_read_local() made things even worse, it can request time at any point, suffering all the problems perf_event_update_userpage() does and more. Because while perf_event_update_userpage() is limited by the context being active, perf_event_read_local() users have no such constraint. Therefore, completely overhaul things and do away with perf_event::shadow_ctx_time. Instead have regular context time updates keep track of this offset directly and provide perf_event_time_now() to complement perf_event_time(). perf_event_time_now() will, in adition to being context wide, also take into account if the context is active. For inactive context, it will not advance time. This latter property means the cgroup perf_cgroup_info context needs to grow addition state to track this. Additionally, since all this is strictly per-cpu, we can use barrier() to order context activity vs context time. Fixes: 7d9285e82db5 ("perf/bpf: Extend the perf_event_read_local() interface, a.k.a. "bpf: perf event change needed for subsequent bpf helpers"") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Song Liu <song@kernel.org> Tested-by: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/r/YcB06DasOBtU0b00@hirez.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01kernel: delete repeated words in commentsRandy Dunlap7-11/+11
[ Upstream commit c034f48e99907d5be147ac8f0f3e630a9307c2be ] Drop repeated words in kernel/events/. {if, the, that, with, time} Drop repeated words in kernel/locking/. {it, no, the} Drop repeated words in kernel/sched/. {in, not} Link: https://lkml.kernel.org/r/20210127023412.26292-1-rdunlap@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Will Deacon <will@kernel.org> [kernel/locking/] Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Will Deacon <will@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01netfilter: conntrack: don't increment invalid counter on NF_REPEATFlorian Westphal1-3/+5
[ Upstream commit 830af2eba40327abec64325a5b08b1e85c37a2e0 ] The packet isn't invalid, REPEAT means we're trying again after cleaning out a stale connection, e.g. via tcp tracker. This caused increases of invalid stat counter in a test case involving frequent connection reuse, even though no packet is actually invalid. Fixes: 56a62e2218f5 ("netfilter: conntrack: fix NF_REPEAT handling") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01powerpc64/bpf: Limit 'ldbrx' to processors compliant with ISA v2.06Naveen N. Rao2-9/+14
[ Upstream commit 3f5f766d5f7f95a69a630da3544a1a0cee1cdddf ] Johan reported the below crash with test_bpf on ppc64 e5500: test_bpf: #296 ALU_END_FROM_LE 64: 0x0123456789abcdef -> 0x67452301 jited:1 Oops: Exception in kernel mode, sig: 4 [#1] BE PAGE_SIZE=4K SMP NR_CPUS=24 QEMU e500 Modules linked in: test_bpf(+) CPU: 0 PID: 76 Comm: insmod Not tainted 5.14.0-03771-g98c2059e008a-dirty #1 NIP: 8000000000061c3c LR: 80000000006dea64 CTR: 8000000000061c18 REGS: c0000000032d3420 TRAP: 0700 Not tainted (5.14.0-03771-g98c2059e008a-dirty) MSR: 0000000080089000 <EE,ME> CR: 88002822 XER: 20000000 IRQMASK: 0 <...> NIP [8000000000061c3c] 0x8000000000061c3c LR [80000000006dea64] .__run_one+0x104/0x17c [test_bpf] Call Trace: .__run_one+0x60/0x17c [test_bpf] (unreliable) .test_bpf_init+0x6a8/0xdc8 [test_bpf] .do_one_initcall+0x6c/0x28c .do_init_module+0x68/0x28c .load_module+0x2460/0x2abc .__do_sys_init_module+0x120/0x18c .system_call_exception+0x110/0x1b8 system_call_common+0xf0/0x210 --- interrupt: c00 at 0x101d0acc <...> ---[ end trace 47b2bf19090bb3d0 ]--- Illegal instruction The illegal instruction turned out to be 'ldbrx' emitted for BPF_FROM_[L|B]E, which was only introduced in ISA v2.06. Guard use of the same and implement an alternative approach for older processors. Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Reported-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/d1e51c6fdf572062cf3009a751c3406bda01b832.1641468127.git.naveen.n.rao@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01NFS: Ensure the server has an up to date ctime before renamingTrond Myklebust1-0/+2
[ Upstream commit 6ff9d99bb88faebf134ca668842349d9718e5464 ] Renaming a file is required by POSIX to update the file ctime, so ensure that the file data is synced to disk so that we don't clobber the updated ctime by writing back after creating the hard link. Fixes: f2c2c552f119 ("NFS: Move delegation recall into the NFSv4 callback for rename_setup()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01NFS: Ensure the server has an up to date ctime before hardlinkingTrond Myklebust1-0/+2
[ Upstream commit 204975036b34f55237bc44c8a302a88468ef21b5 ] Creating a hard link is required by POSIX to update the file ctime, so ensure that the file data is synced to disk so that we don't clobber the updated ctime by writing back after creating the hard link. Fixes: 9f7682728728 ("NFS: Move the delegation return down into nfs4_proc_link()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01ipv6: annotate accesses to fn->fn_sernumEric Dumazet3-12/+15
commit aafc2e3285c2d7a79b7ee15221c19fbeca7b1509 upstream. struct fib6_node's fn_sernum field can be read while other threads change it. Add READ_ONCE()/WRITE_ONCE() annotations. Do not change existing smp barriers in fib6_get_cookie_safe() and __fib6_update_sernum_upto_root() syzbot reported: BUG: KCSAN: data-race in fib6_clean_node / inet6_csk_route_socket write to 0xffff88813df62e2c of 4 bytes by task 1920 on cpu 1: fib6_clean_node+0xc2/0x260 net/ipv6/ip6_fib.c:2178 fib6_walk_continue+0x38e/0x430 net/ipv6/ip6_fib.c:2112 fib6_walk net/ipv6/ip6_fib.c:2160 [inline] fib6_clean_tree net/ipv6/ip6_fib.c:2240 [inline] __fib6_clean_all+0x1a9/0x2e0 net/ipv6/ip6_fib.c:2256 fib6_flush_trees+0x6c/0x80 net/ipv6/ip6_fib.c:2281 rt_genid_bump_ipv6 include/net/net_namespace.h:488 [inline] addrconf_dad_completed+0x57f/0x870 net/ipv6/addrconf.c:4230 addrconf_dad_work+0x908/0x1170 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307 worker_thread+0x616/0xa70 kernel/workqueue.c:2454 kthread+0x1bf/0x1e0 kernel/kthread.c:359 ret_from_fork+0x1f/0x30 read to 0xffff88813df62e2c of 4 bytes by task 15701 on cpu 0: fib6_get_cookie_safe include/net/ip6_fib.h:285 [inline] rt6_get_cookie include/net/ip6_fib.h:306 [inline] ip6_dst_store include/net/ip6_route.h:234 [inline] inet6_csk_route_socket+0x352/0x3c0 net/ipv6/inet6_connection_sock.c:109 inet6_csk_xmit+0x91/0x1e0 net/ipv6/inet6_connection_sock.c:121 __tcp_transmit_skb+0x1323/0x1840 net/ipv4/tcp_output.c:1402 tcp_transmit_skb net/ipv4/tcp_output.c:1420 [inline] tcp_write_xmit+0x1450/0x4460 net/ipv4/tcp_output.c:2680 __tcp_push_pending_frames+0x68/0x1c0 net/ipv4/tcp_output.c:2864 tcp_push+0x2d9/0x2f0 net/ipv4/tcp.c:725 mptcp_push_release net/mptcp/protocol.c:1491 [inline] __mptcp_push_pending+0x46c/0x490 net/mptcp/protocol.c:1578 mptcp_sendmsg+0x9ec/0xa50 net/mptcp/protocol.c:1764 inet6_sendmsg+0x5f/0x80 net/ipv6/af_inet6.c:643 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg net/socket.c:725 [inline] kernel_sendmsg+0x97/0xd0 net/socket.c:745 sock_no_sendpage+0x84/0xb0 net/core/sock.c:3086 inet_sendpage+0x9d/0xc0 net/ipv4/af_inet.c:834 kernel_sendpage+0x187/0x200 net/socket.c:3492 sock_sendpage+0x5a/0x70 net/socket.c:1007 pipe_to_sendpage+0x128/0x160 fs/splice.c:364 splice_from_pipe_feed fs/splice.c:418 [inline] __splice_from_pipe+0x207/0x500 fs/splice.c:562 splice_from_pipe fs/splice.c:597 [inline] generic_splice_sendpage+0x94/0xd0 fs/splice.c:746 do_splice_from fs/splice.c:767 [inline] direct_splice_actor+0x80/0xa0 fs/splice.c:936 splice_direct_to_actor+0x345/0x650 fs/splice.c:891 do_splice_direct+0x106/0x190 fs/splice.c:979 do_sendfile+0x675/0xc40 fs/read_write.c:1245 __do_sys_sendfile64 fs/read_write.c:1310 [inline] __se_sys_sendfile64 fs/read_write.c:1296 [inline] __x64_sys_sendfile64+0x102/0x140 fs/read_write.c:1296 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0x0000026f -> 0x00000271 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 15701 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 The Fixes tag I chose is probably arbitrary, I do not think we need to backport this patch to older kernels. Fixes: c5cff8561d2d ("ipv6: add rcu grace period before freeing fib6_node") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220120174112.1126644-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/msm/dsi: invalid parameter check in msm_dsi_phy_enableJosé Expósito1-1/+3
commit 5e761a2287234bc402ba7ef07129f5103bcd775c upstream. The function performs a check on the "phy" input parameter, however, it is used before the check. Initialize the "dev" variable after the sanity check to avoid a possible NULL pointer dereference. Fixes: 5c8290284402b ("drm/msm/dsi: Split PHY drivers to separate files") Addresses-Coverity-ID: 1493860 ("Null pointer dereference") Signed-off-by: José Expósito <jose.exposito89@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220116181844.7400-1-jose.exposito89@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/msm/dsi: Fix missing put_device() call in dsi_get_phyMiaoqian Lin1-1/+6
commit c04c3148ca12227d92f91b355b4538cc333c9922 upstream. If of_find_device_by_node() succeeds, dsi_get_phy() doesn't a corresponding put_device(). Thus add put_device() to fix the exception handling. Fixes: ec31abf ("drm/msm/dsi: Separate PHY to another platform device") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20211230070943.18116-1-linmq006@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/msm: Fix wrong size calculationXianting Tian1-1/+1
commit 0a727b459ee39bd4c5ced19d6024258ac87b6b2e upstream. For example, memory-region in .dts as below, reg = <0x0 0x50000000 0x0 0x20000000> We can get below values, struct resource r; r.start = 0x50000000; r.end = 0x6fffffff; So the size should be: size = r.end - r.start + 1 = 0x20000000 Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com> Fixes: 072f1f9168ed ("drm/msm: add support for "stolen" mem") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220112123334.749776-1-xianting.tian@linux.alibaba.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01net-procfs: show net devices bound packet typesJianguo Wu1-3/+32
commit 1d10f8a1f40b965d449e8f2d5ed7b96a7c138b77 upstream. After commit:7866a621043f ("dev: add per net_device packet type chains"), we can not get packet types that are bound to a specified net device by /proc/net/ptype, this patch fix the regression. Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch: Before: [root@localhost ~]# cat /proc/net/ptype Type Device Function 0800 ip_rcv 0806 arp_rcv 86dd ipv6_rcv After: [root@localhost ~]# cat /proc/net/ptype Type Device Function ALL ens192 tpacket_rcv 0800 ip_rcv 0806 arp_rcv 86dd ipv6_rcv v1 -> v2: - fix the regression rather than adding new /proc API as suggested by Stephen Hemminger. Fixes: 7866a621043f ("dev: add per net_device packet type chains") Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01NFSv4: nfs_atomic_open() can race when looking up a non-regular fileTrond Myklebust1-0/+5
commit 1751fc1db36f6f411709e143d5393f92d12137a9 upstream. If the file type changes back to being a regular file on the server between the failed OPEN and our LOOKUP, then we need to re-run the OPEN. Fixes: 0dd2b474d0b6 ("nfs: implement i_op->atomic_open()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01NFSv4: Handle case where the lookup of a directory failsTrond Myklebust1-0/+13
commit ac795161c93699d600db16c1a8cc23a65a1eceaf upstream. If the application sets the O_DIRECTORY flag, and tries to open a regular file, nfs_atomic_open() will punt to doing a regular lookup. If the server then returns a regular file, we will happily return a file descriptor with uninitialised open state. The fix is to return the expected ENOTDIR error in these cases. Reported-by: Lyu Tao <tao.lyu@epfl.ch> Fixes: 0dd2b474d0b6 ("nfs: implement i_op->atomic_open()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01hwmon: (lm90) Reduce maximum conversion rate for G781Guenter Roeck1-1/+1
[ Upstream commit a66c5ed539277b9f2363bbace0dba88b85b36c26 ] According to its datasheet, G781 supports a maximum conversion rate value of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only support a maximum conversion rate value of 7 (125 ms). On the other side, chips labeled G781-1 and G784 were found to support a conversion rate value of 8. There is no known means to distinguish G780 from G781 or G784; all chips report the same manufacturer ID and chip revision. Setting the conversion rate register value to 8 on chips not supporting it causes unexpected behavior since the real conversion rate is set to 0 (16 seconds) if a value of 8 is written into the conversion rate register. Limit the conversion rate register value to 7 for all G78x chips to avoid the problem. Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01ipv4: avoid using shared IP generator for connected socketsEric Dumazet1-11/+10
commit 23f57406b82de51809d5812afd96f210f8b627f3 upstream. ip_select_ident_segs() has been very conservative about using the connected socket private generator only for packets with IP_DF set, claiming it was needed for some VJ compression implementations. As mentioned in this referenced document, this can be abused. (Ref: Off-Path TCP Exploits of the Mixed IPID Assignment) Before switching to pure random IPID generation and possibly hurt some workloads, lets use the private inet socket generator. Not only this will remove one vulnerability, this will also improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT Fixes: 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reported-by: Ray Che <xijiache@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01ping: fix the sk_bound_dev_if match in ping_lookupXin Long1-1/+2
commit 2afc3b5a31f9edf3ef0f374f5d70610c79c93a42 upstream. When 'ping' changes to use PING socket instead of RAW socket by: # sysctl -w net.ipv4.ping_group_range="0 100" the selftests 'router_broadcast.sh' will fail, as such command # ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b can't receive the response skb by the PING socket. It's caused by mismatch of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket, as dif is vrf-h1 if dif's master was set to vrf-h1. This patch is to fix this regression by also checking the sk_bound_dev_if against sdif so that the packets can stil be received even if the socket is not bound to the vrf device but to the real iif. Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01hwmon: (lm90) Mark alert as broken for MAX6680Guenter Roeck1-1/+1
commit 94746b0ba479743355e0d3cc1cb9cfe3011fb8be upstream. Experiments with MAX6680 and MAX6681 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01hwmon: (lm90) Mark alert as broken for MAX6646/6647/6649Guenter Roeck1-1/+1
commit f614629f9c1080dcc844a8430e3fb4c37ebbf05d upstream. Experiments with MAX6646 and MAX6648 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01net: fix information leakage in /proc/net/ptypeCongyu Liu3-1/+5
commit 47934e06b65637c88a762d9c98329ae6e3238888 upstream. In one net namespace, after creating a packet socket without binding it to a device, users in other net namespaces can observe the new `packet_type` added by this packet socket by reading `/proc/net/ptype` file. This is minor information leakage as packet socket is namespace aware. Add a net pointer in `packet_type` to keep the net namespace of of corresponding packet socket. In `ptype_seq_show`, this net pointer must be checked when it is not NULL. Fixes: 2feb27dbe00c ("[NETNS]: Minor information leak via /proc/net/ptype file.") Signed-off-by: Congyu Liu <liu3101@purdue.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01ipv6_tunnel: Rate limit warning messagesIdo Schimmel1-4/+4
commit 6cee105e7f2ced596373951d9ea08dacc3883c68 upstream. The warning messages can be invoked from the data path for every packet transmitted through an ip6gre netdev, leading to high CPU utilization. Fix that by rate limiting the messages. Fixes: 09c6bbf090ec ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime") Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Tested-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01scsi: bnx2fc: Flush destroy_work queue before calling bnx2fc_interface_put()John Meneghini1-15/+5
commit 847f9ea4c5186fdb7b84297e3eeed9e340e83fce upstream. The bnx2fc_destroy() functions are removing the interface before calling destroy_work. This results multiple WARNings from sysfs_remove_group() as the controller rport device attributes are removed too early. Replace the fcoe_port's destroy_work queue. It's not needed. The problem is easily reproducible with the following steps. Example: $ dmesg -w & $ systemctl enable --now fcoe $ fipvlan -s -c ens2f1 $ fcoeadm -d ens2f1.802 [ 583.464488] host2: libfc: Link down on port (7500a1) [ 583.472651] bnx2fc: 7500a1 - rport not created Yet!! [ 583.490468] ------------[ cut here ]------------ [ 583.538725] sysfs group 'power' not found for kobject 'rport-2:0-0' [ 583.568814] WARNING: CPU: 3 PID: 192 at fs/sysfs/group.c:279 sysfs_remove_group+0x6f/0x80 [ 583.607130] Modules linked in: dm_service_time 8021q garp mrp stp llc bnx2fc cnic uio rpcsec_gss_krb5 auth_rpcgss nfsv4 ... [ 583.942994] CPU: 3 PID: 192 Comm: kworker/3:2 Kdump: loaded Not tainted 5.14.0-39.el9.x86_64 #1 [ 583.984105] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013 [ 584.016535] Workqueue: fc_wq_2 fc_rport_final_delete [scsi_transport_fc] [ 584.050691] RIP: 0010:sysfs_remove_group+0x6f/0x80 [ 584.074725] Code: ff 5b 48 89 ef 5d 41 5c e9 ee c0 ff ff 48 89 ef e8 f6 b8 ff ff eb d1 49 8b 14 24 48 8b 33 48 c7 c7 ... [ 584.162586] RSP: 0018:ffffb567c15afdc0 EFLAGS: 00010282 [ 584.188225] RAX: 0000000000000000 RBX: ffffffff8eec4220 RCX: 0000000000000000 [ 584.221053] RDX: ffff8c1586ce84c0 RSI: ffff8c1586cd7cc0 RDI: ffff8c1586cd7cc0 [ 584.255089] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb567c15afc00 [ 584.287954] R10: ffffb567c15afbf8 R11: ffffffff8fbe7f28 R12: ffff8c1486326400 [ 584.322356] R13: ffff8c1486326480 R14: ffff8c1483a4a000 R15: 0000000000000004 [ 584.355379] FS: 0000000000000000(0000) GS:ffff8c1586cc0000(0000) knlGS:0000000000000000 [ 584.394419] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 584.421123] CR2: 00007fe95a6f7840 CR3: 0000000107674002 CR4: 00000000000606e0 [ 584.454888] Call Trace: [ 584.466108] device_del+0xb2/0x3e0 [ 584.481701] device_unregister+0x13/0x60 [ 584.501306] bsg_unregister_queue+0x5b/0x80 [ 584.522029] bsg_remove_queue+0x1c/0x40 [ 584.541884] fc_rport_final_delete+0xf3/0x1d0 [scsi_transport_fc] [ 584.573823] process_one_work+0x1e3/0x3b0 [ 584.592396] worker_thread+0x50/0x3b0 [ 584.609256] ? rescuer_thread+0x370/0x370 [ 584.628877] kthread+0x149/0x170 [ 584.643673] ? set_kthread_struct+0x40/0x40 [ 584.662909] ret_from_fork+0x22/0x30 [ 584.680002] ---[ end trace 53575ecefa942ece ]--- Link: https://lore.kernel.org/r/20220115040044.1013475-1-jmeneghi@redhat.com Fixes: 0cbf32e1681d ("[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks") Tested-by: Guangwu Zhang <guazhang@redhat.com> Co-developed-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01rpmsg: char: Fix race between the release of rpmsg_eptdev and cdevMatthias Kaehlcke1-9/+2
commit 7a534ae89e34e9b51acb5a63dd0f88308178b46a upstream. struct rpmsg_eptdev contains a struct cdev. The current code frees the rpmsg_eptdev struct in rpmsg_eptdev_destroy(), but the cdev is a managed object, therefore its release is not predictable and the rpmsg_eptdev could be freed before the cdev is entirely released. The cdev_device_add/del() API was created to address this issue (see commit '233ed09d7fda ("chardev: add helper function to register char devs with a struct device")'), use it instead of cdev add/del(). Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.2.Idde68b05b88d4a2e6e54766c653f3a6d9e419ce6@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01rpmsg: char: Fix race between the release of rpmsg_ctrldev and cdevSujit Kautkar1-9/+2
commit b7fb2dad571d1e21173c06cef0bced77b323990a upstream. struct rpmsg_ctrldev contains a struct cdev. The current code frees the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the cdev is a managed object, therefore its release is not predictable and the rpmsg_ctrldev could be freed before the cdev is entirely released, as in the backtrace below. [ 93.625603] ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x7c [ 93.636115] WARNING: CPU: 0 PID: 12 at lib/debugobjects.c:488 debug_print_object+0x13c/0x1b0 [ 93.644799] Modules linked in: veth xt_cgroup xt_MASQUERADE rfcomm algif_hash algif_skcipher af_alg uinput ip6table_nat fuse uvcvideo videobuf2_vmalloc venus_enc venus_dec videobuf2_dma_contig hci_uart btandroid btqca snd_soc_rt5682_i2c bluetooth qcom_spmi_temp_alarm snd_soc_rt5682v [ 93.715175] CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: G B 5.4.163-lockdep #26 [ 93.723855] Hardware name: Google Lazor (rev3 - 8) with LTE (DT) [ 93.730055] Workqueue: events kobject_delayed_cleanup [ 93.735271] pstate: 60c00009 (nZCv daif +PAN +UAO) [ 93.740216] pc : debug_print_object+0x13c/0x1b0 [ 93.744890] lr : debug_print_object+0x13c/0x1b0 [ 93.749555] sp : ffffffacf5bc7940 [ 93.752978] x29: ffffffacf5bc7940 x28: dfffffd000000000 [ 93.758448] x27: ffffffacdb11a800 x26: dfffffd000000000 [ 93.763916] x25: ffffffd0734f856c x24: dfffffd000000000 [ 93.769389] x23: 0000000000000000 x22: ffffffd0733c35b0 [ 93.774860] x21: ffffffd0751994a0 x20: ffffffd075ec27c0 [ 93.780338] x19: ffffffd075199100 x18: 00000000000276e0 [ 93.785814] x17: 0000000000000000 x16: dfffffd000000000 [ 93.791291] x15: ffffffffffffffff x14: 6e6968207473696c [ 93.796768] x13: 0000000000000000 x12: ffffffd075e2b000 [ 93.802244] x11: 0000000000000001 x10: 0000000000000000 [ 93.807723] x9 : d13400dff1921900 x8 : d13400dff1921900 [ 93.813200] x7 : 0000000000000000 x6 : 0000000000000000 [ 93.818676] x5 : 0000000000000080 x4 : 0000000000000000 [ 93.824152] x3 : ffffffd0732a0fa4 x2 : 0000000000000001 [ 93.829628] x1 : ffffffacf5bc7580 x0 : 0000000000000061 [ 93.835104] Call trace: [ 93.837644] debug_print_object+0x13c/0x1b0 [ 93.841963] __debug_check_no_obj_freed+0x25c/0x3c0 [ 93.846987] debug_check_no_obj_freed+0x18/0x20 [ 93.851669] slab_free_freelist_hook+0xbc/0x1e4 [ 93.856346] kfree+0xfc/0x2f4 [ 93.859416] rpmsg_ctrldev_release_device+0x78/0xb8 [ 93.864445] device_release+0x84/0x168 [ 93.868310] kobject_cleanup+0x12c/0x298 [ 93.872356] kobject_delayed_cleanup+0x10/0x18 [ 93.876948] process_one_work+0x578/0x92c [ 93.881086] worker_thread+0x804/0xcf8 [ 93.884963] kthread+0x2a8/0x314 [ 93.888303] ret_from_fork+0x10/0x18 The cdev_device_add/del() API was created to address this issue (see commit '233ed09d7fda ("chardev: add helper function to register char devs with a struct device")'), use it instead of cdev add/del(). Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Signed-off-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: roles: fix include/linux/usb/role.h compile issueLinyu Yuan1-0/+6
commit 945c37ed564770c78dfe6b9f08bed57a1b4e60ef upstream. when CONFIG_USB_ROLE_SWITCH is not defined, add usb_role_switch_find_by_fwnode() definition which return NULL. Fixes: c6919d5e0cd1 ("usb: roles: Add usb_role_switch_find_by_fwnode()") Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com> Link: https://lore.kernel.org/r/1641818608-25039-1-git-send-email-quic_linyyuan@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: fix unsigned stat widthsJoe Damato3-7/+7
commit 3b8428b84539c78fdc8006c17ebd25afd4722d51 upstream. Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match the width of the stats counters in struct i40e_rx_queue_stats. Update debugfs code to use the correct format specifier for u64. Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Joe Damato <jdamato@fastly.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix for failed to init adminq while VF resetKaren Sornek3-2/+46
commit 0f344c8129a5337dae50e31b817dd50a60ff238c upstream. Fix for failed to init adminq: -53 while VF is resetting via MAC address changing procedure. Added sync module to avoid reading deadbeef value in reinit adminq during software reset. Without this patch it is possible to trigger VF reset procedure during reinit adminq. This resulted in an incorrect reading of value from the AQP registers and generated the -53 error. Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Karen Sornek <karen.sornek@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix queues reservation for XDPSylwester Dziedziuch1-0/+14
commit 92947844b8beee988c0ce17082b705c2f75f0742 upstream. When XDP was configured on a system with large number of CPUs and X722 NIC there was a call trace with NULL pointer dereference. i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12 i40e 0000:87:00.0: setup of MAIN VSI failed BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e] Call Trace: ? i40e_reconfig_rss_queues+0x130/0x130 [i40e] dev_xdp_install+0x61/0xe0 dev_xdp_attach+0x18a/0x4c0 dev_change_xdp_fd+0x1e6/0x220 do_setlink+0x616/0x1030 ? ahci_port_stop+0x80/0x80 ? ata_qc_issue+0x107/0x1e0 ? lock_timer_base+0x61/0x80 ? __mod_timer+0x202/0x380 rtnl_setlink+0xe5/0x170 ? bpf_lsm_binder_transaction+0x10/0x10 ? security_capable+0x36/0x50 rtnetlink_rcv_msg+0x121/0x350 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x50/0xf0 netlink_unicast+0x1d3/0x2a0 netlink_sendmsg+0x22a/0x440 sock_sendmsg+0x5e/0x60 __sys_sendto+0xf0/0x160 ? __sys_getsockname+0x7e/0xc0 ? _copy_from_user+0x3c/0x80 ? __sys_setsockopt+0xc8/0x1a0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f83fa7a39e0 This was caused by PF queue pile fragmentation due to flow director VSI queue being placed right after main VSI. Because of this main VSI was not able to resize its queue allocation for XDP resulting in no queues allocated for main VSI when XDP was turned on. Fix this by always allocating last queue in PF queue pile for a flow director VSI. Fixes: 41c445ff0f48 ("i40e: main driver core") Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix issue when maximum queues is exceededJedrzej Jagielski3-13/+61
commit d701658a50a471591094b3eb3961b4926cc8f104 upstream. Before this patch VF interface vanished when maximum queue number was exceeded. Driver tried to add next queues even if there was not enough space. PF sent incorrect number of queues to the VF when there were not enough of them. Add an additional condition introduced to check available space in 'qp_pile' before proceeding. This condition makes it impossible to add queues if they number is greater than the number resulting from available space. Also add the search for free space in PF queue pair piles. Without this patch VF interfaces are not seen when available space for queues has been exceeded and following logs appears permanently in dmesg: "Unable to get VF config (-32)". "VF 62 failed opcode 3, retval: -5" "Unable to get VF config due to PF error condition, not retrying" Fixes: 7daa6bf3294e ("i40e: driver core headers") Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Increase delay to 1 s after global EMP resetJedrzej Jagielski1-9/+3
commit 9b13bd53134c9ddd544a790125199fdbdb505e67 upstream. Recently simplified i40e_rebuild causes that FW sometimes is not ready after NVM update, the ping does not return. Increase the delay in case of EMP reset. Old delay of 300 ms was introduced for specific cards for 710 series. Now it works for all the cards and delay was increased. Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01powerpc/32: Fix boot failure with GCC latent entropy pluginChristophe Leroy2-0/+4
commit bba496656a73fc1d1330b49c7f82843836e9feb1 upstream. Boot fails with GCC latent entropy plugin enabled. This is due to early boot functions trying to access 'latent_entropy' global data while the kernel is not relocated at its final destination yet. As there is no way to tell GCC to use PTRRELOC() to access it, disable latent entropy plugin in early_32.o and feature-fixups.o and code-patching.o Fixes: 38addce8b600 ("gcc-plugins: Add latent_entropy plugin") Cc: stable@vger.kernel.org # v4.9+ Reported-by: Erhard Furtner <erhard_f@mailbox.org> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215217 Link: https://lore.kernel.org/r/2bac55483b8daf5b1caa163a45fa5f9cdbe18be4.1640178426.git.christophe.leroy@csgroup.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01powerpc/32s: Fix kasan_init_region() for KASANChristophe Leroy3-33/+38
commit d37823c3528e5e0705fc7746bcbc2afffb619259 upstream. It has been reported some configuration where the kernel doesn't boot with KASAN enabled. This is due to wrong BAT allocation for the KASAN area: ---[ Data Block Address Translation ]--- 0: 0xc0000000-0xcfffffff 0x00000000 256M Kernel rw m 1: 0xd0000000-0xdfffffff 0x10000000 256M Kernel rw m 2: 0xe0000000-0xefffffff 0x20000000 256M Kernel rw m 3: 0xf8000000-0xf9ffffff 0x2a000000 32M Kernel rw m 4: 0xfa000000-0xfdffffff 0x2c000000 64M Kernel rw m A BAT must have both virtual and physical addresses alignment matching the size of the BAT. This is not the case for BAT 4 above. Fix kasan_init_region() by using block_size() function that is in book3s32/mmu.c. To be able to reuse it here, make it non static and change its name to bat_block_size() in order to avoid name conflict with block_size() defined in <linux/blkdev.h> Also reuse find_free_bat() to avoid an error message from setbat() when no BAT is available. And allocate memory outside of linear memory mapping to avoid wasting that precious space. With this change we get correct alignment for BATs and KASAN shadow memory is allocated outside the linear memory space. ---[ Data Block Address Translation ]--- 0: 0xc0000000-0xcfffffff 0x00000000 256M Kernel rw 1: 0xd0000000-0xdfffffff 0x10000000 256M Kernel rw 2: 0xe0000000-0xefffffff 0x20000000 256M Kernel rw 3: 0xf8000000-0xfbffffff 0x7c000000 64M Kernel rw 4: 0xfc000000-0xfdffffff 0x7a000000 32M Kernel rw Fixes: 7974c4732642 ("powerpc/32s: Implement dedicated kasan_init_region()") Cc: stable@vger.kernel.org Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Tested-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/7a50ef902494d1325227d47d33dada01e52e5518.1641818726.git.christophe.leroy@csgroup.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01powerpc/32s: Allocate one 256k IBAT instead of two consecutives 128k IBATsChristophe Leroy1-3/+2
commit 37eb7ca91b692e8e49e7dd50158349a6c8fb5b09 upstream. Today we have the following IBATs allocated: ---[ Instruction Block Add