| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_wb.h:24 Cannot find
identifier on line: *
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_wb.h:57 struct member
'setup_roi' not described in 'dpu_hw_wb_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_wb.h:75 struct member
'caps' not described in 'dpu_hw_wb'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695672/
Link: https://lore.kernel.org/r/20251219184638.1813181-16-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:19 Incorrect use of
kernel-doc format: * set_limit_conf - set transaction limit config
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:29 Incorrect use of
kernel-doc format: * get_limit_conf - get transaction limit config
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:39 Incorrect use of
kernel-doc format: * set_halt_ctrl - set halt control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:48 Incorrect use of
kernel-doc format: * get_halt_ctrl - get halt control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:57 Incorrect use of
kernel-doc format: * set_qos_remap - set QoS priority remap
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:67 Incorrect use of
kernel-doc format: * set_mem_type - set memory type
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:76 Incorrect use of
kernel-doc format: * clear_errors - clear any vbif errors
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:88 Incorrect use of
kernel-doc format: * set_write_gather_en - set write_gather enable
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'limit' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'set_limit_conf' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'get_limit_conf' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'set_halt_ctrl' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'get_halt_ctrl' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'set_qos_remap' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'set_mem_type' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
's' not described in 'dpu_hw_vbif_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_vbif.h:93 struct member
'set_write_gather_en' not described in 'dpu_hw_vbif_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695680/
Link: https://lore.kernel.org/r/20251219184638.1813181-15-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:93 Incorrect use of
kernel-doc format: * setup_traffic_shaper() : Setup traffic shaper control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:101 Incorrect use of
kernel-doc format: * setup_clk_force_ctrl - set clock force control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:111 Incorrect use of
kernel-doc format: * get_danger_status - get danger status
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:119 Incorrect use of
kernel-doc format: * setup_vsync_source - setup vsync source
configuration details
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:127 Incorrect use of
kernel-doc format: * get_safe_status - get safe status
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:135 Incorrect use of
kernel-doc format: * dp_phy_intf_sel - configure intf to phy mapping
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:142 Incorrect use of
kernel-doc format: * intf_audio_select - select the external interface
for audio
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'setup_clk_force_ctrl' not described in 'dpu_hw_mdp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'get_danger_status' not described in 'dpu_hw_mdp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'setup_vsync_source' not described in 'dpu_hw_mdp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'get_safe_status' not described in 'dpu_hw_mdp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'dp_phy_intf_sel' not described in 'dpu_hw_mdp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_top.h:146 struct member
'intf_audio_select' not described in 'dpu_hw_mdp_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695669/
Link: https://lore.kernel.org/r/20251219184638.1813181-14-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Modify non-kernel-doc comments to begin with "/*" instead of "/**".
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:17 missing initial
short description on line: * Flags
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:19 expecting
prototype for Flags(). Prototype was for DPU_SSPP_FLIP_LR() instead
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:26 This comment
starts with '/**', but isn't a kernel-doc comment.
* Component indices
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:47 cannot understand
function prototype: 'enum dpu_sspp_multirect_index'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:152 struct member
'dst_rect' not described in 'dpu_sw_pipe_cfg'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:174 struct member
'multirect_index' not described in 'dpu_sw_pipe'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:174 struct member
'multirect_mode' not described in 'dpu_sw_pipe'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:183 Incorrect use of
kernel-doc format: * setup_format - setup pixel format cropping
rectangle, flip
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:192 Incorrect use of
kernel-doc format: * setup_rects - setup pipe ROI rectangles
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:200 Incorrect use of
kernel-doc format: * setup_pe - setup pipe pixel extension
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:208 Incorrect use of
kernel-doc format: * setup_sourceaddress - setup pipe source addresses
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:216 Incorrect use of
kernel-doc format: * setup_csc - setup color space coversion
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:223 Incorrect use of
kernel-doc format: * setup_solidfill - enable/disable colorfill
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:231 Incorrect use of
kernel-doc format: * setup_multirect - setup multirect configuration
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:238 Incorrect use of
kernel-doc format: * setup_sharpening - setup sharpening
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:247 Incorrect use of
kernel-doc format: * setup_qos_lut - setup QoS LUTs
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:255 Incorrect use of
kernel-doc format: * setup_qos_ctrl - setup QoS control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:263 Incorrect use of
kernel-doc format: * setup_clk_force_ctrl - setup clock force control
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:271 Incorrect use of
kernel-doc format: * setup_histogram - setup histograms
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:279 Incorrect use of
kernel-doc format: * setup_scaler - setup scaler
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:288 Incorrect use of
kernel-doc format: * setup_cdp - setup client driven prefetch
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_format' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_rects' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_pe' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_sourceaddress' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_csc' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_solidfill' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_multirect' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_sharpening' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_qos_lut' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_qos_ctrl' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_clk_force_ctrl' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_histogram' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_scaler' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:296 struct member
'setup_cdp' not described in 'dpu_hw_sspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.h:320 struct member
'mdss_ver' not described in 'dpu_hw_sspp'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695661/
Link: https://lore.kernel.org/r/20251219184638.1813181-13-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:36 Cannot find
identifier on line: *
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:46 Incorrect use
of kernel-doc format: * enables vysnc generation and sets up init value of
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:53 Incorrect use
of kernel-doc format: * disables tear check block
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:58 Incorrect use
of kernel-doc format: * read, modify, write to either set or clear
listening to external TE
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:65 Incorrect use
of kernel-doc format: * Obtain current vertical line counter
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:70 Incorrect use
of kernel-doc format: * Disable autorefresh if enabled
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:75 Incorrect use
of kernel-doc format: * Setup dither matix for pingpong block
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:80 Incorrect use
of kernel-doc format: * Enable DSC
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:85 Incorrect use
of kernel-doc format: * Disable DSC
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:90 Incorrect use
of kernel-doc format: * Setup DSC
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:93 struct member
'connect_external_te' not described in 'dpu_hw_pingpong_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:93 struct member
'disable_autorefresh' not described in 'dpu_hw_pingpong_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:93 struct member
'enable_dsc' not described in 'dpu_hw_pingpong_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:93 struct member
'disable_dsc' not described in 'dpu_hw_pingpong_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_pingpong.h:93 struct member
'setup_dsc' not described in 'dpu_hw_pingpong_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695659/
Link: https://lore.kernel.org/r/20251219184638.1813181-12-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Delete one "empty" kernel-doc line to eliminate a warning:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_merge3d.h:14 Cannot find
identifier on line: *
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695673/
Link: https://lore.kernel.org/r/20251219184638.1813181-11-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:27 Cannot find
identifier on line: *
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:52 Incorrect use of
kernel-doc format: * Clear layer mixer to pipe configuration
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:59 Incorrect use of
kernel-doc format: * Configure layer mixer to pipe configuration
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:69 Incorrect use of
kernel-doc format: * setup_border_color : enable/disable border color
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:76 Incorrect use of
kernel-doc format: * setup_misr: Enable/disable MISR
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:81 Incorrect use of
kernel-doc format: * collect_misr: Read MISR signature
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_mixer_out' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_blend_config' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_alpha_out' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'clear_all_blendstages' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_blendstage' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_border_color' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'setup_misr' not described in 'dpu_hw_lm_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.h:84 struct member
'collect_misr' not described in 'dpu_hw_lm_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695648/
Link: https://lore.kernel.org/r/20251219184638.1813181-10-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:76 duplicate section
name 'Return'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:112 Incorrect use of
kernel-doc format: * Disable autorefresh if enabled
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'setup_timing_gen' not described in 'dpu_hw_intf_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'setup_prg_fetch' not described in 'dpu_hw_intf_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'enable_timing' not described in 'dpu_hw_intf_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'get_status' not described in 'dpu_hw_intf_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'get_line_count' not described in 'dpu_hw_intf_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h:118 struct member
'disable_autorefresh' not described in 'dpu_hw_intf_ops'
dpu_hw_intf.h:119: warning: Excess struct member 'get_vsync_info'
description in 'dpu_hw_intf_ops'
dpu_hw_intf.h:119: warning: Excess struct member 'setup_autorefresh'
description in 'dpu_hw_intf_ops'
dpu_hw_intf.h:119: warning: Excess struct member 'get_autorefresh'
description in 'dpu_hw_intf_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695646/
Link: https://lore.kernel.org/r/20251219184638.1813181-9-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.h:33 expecting prototype
for struct dpu_hw_pcc. Prototype was for struct dpu_hw_pcc_cfg instead
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.h:42 Incorrect use of
kernel-doc format: * setup_pcc - setup dspp pcc
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.h:48 struct member
'setup_pcc' not described in 'dpu_hw_dspp_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dspp.h:76 expecting prototype
for dpu_hw_dspp(). Prototype was for to_dpu_hw_dspp() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695652/
Link: https://lore.kernel.org/r/20251219184638.1813181-8-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:23 Incorrect use of
kernel-doc format: * dsc_disable - disable dsc
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:29 Incorrect use of
kernel-doc format: * dsc_config - configures dsc encoder
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:41 Incorrect use of
kernel-doc format: * dsc_config_thresh - programs panel thresholds
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:50 struct member
'dsc_disable' not described in 'dpu_hw_dsc_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:50 struct member
'dsc_config' not described in 'dpu_hw_dsc_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:50 struct member
'dsc_config_thresh' not described in 'dpu_hw_dsc_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_dsc.h:50 struct member
'dsc_bind_pingpong_blk' not described in 'dpu_hw_dsc_ops'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695658/
Link: https://lore.kernel.org/r/20251219184638.1813181-7-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct or add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cwb.h:30 Cannot find
identifier on line: *
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cwb.h:61 expecting prototype
for dpu_hw_cwb(). Prototype was for to_dpu_hw_cwb() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695664/
Link: https://lore.kernel.org/r/20251219184638.1813181-6-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct and add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:18 cannot understand
function prototype: 'enum dpu_ctl_mode_sel'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:58 struct member 'wb'
not described in 'dpu_hw_intf_cfg'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:66 Incorrect use of
kernel-doc format: * kickoff hw operation for Sw controlled interfaces
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:73 Incorrect use of
kernel-doc format: * check if the ctl is started
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:80 Incorrect use of
kernel-doc format: * kickoff prepare is in progress hw operation for sw
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:88 Incorrect use of
kernel-doc format: * Clear the value of the cached pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:96 Incorrect use of
kernel-doc format: * Query the value of the cached pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:103 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:112 Incorrect use of
kernel-doc format: * OR in the given flushbits to the
cached pending_(wb_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:121 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(cwb_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:130 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(intf_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:139 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(periph_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:148 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(merge_3d_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:157 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:166 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:175 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:185 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(dsc_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:194 Incorrect use of
kernel-doc format: * OR in the given flushbits to the cached
pending_(cdm_)flush_mask
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:202 Incorrect use of
kernel-doc format: * Write the value of the pending_flush_mask to hardware
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:208 Incorrect use of
kernel-doc format: * Read the value of the flush register
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:215 Incorrect use of
kernel-doc format: * Setup ctl_path interface config
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:223 Incorrect use of
kernel-doc format: * reset ctl_path interface config
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:244 Incorrect use of
kernel-doc format: * Set all blend stages to disabled
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:250 Incorrect use of
kernel-doc format: * Configure layer mixer to pipe configuration
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:262 Incorrect use of
kernel-doc format: * Set active pipes attached to this CTL
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:270 Incorrect use of
kernel-doc format: * Set active layer mixers attached to this CTL
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:277 struct member
'trigger_start' not described in 'dpu_hw_ctl_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:277 struct member
'is_started' not described in 'dpu_hw_ctl_ops'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:277 struct member
'trigger_pending' not described in 'dpu_hw_ctl_ops'
[many here]
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:319 struct member
'pending_periph_flush_mask' not described in 'dpu_hw_ctl'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:319 struct member
'pending_merge_3d_flush_mask' not described in 'dpu_hw_ctl'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:319 struct member
'pending_dspp_flush_mask' not described in 'dpu_hw_ctl'
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h:327 expecting
prototype for dpu_hw_ctl(). Prototype was for to_dpu_hw_ctl() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695649/
Link: https://lore.kernel.org/r/20251219184638.1813181-5-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct and add kernel-doc comments to eliminate all warnings:
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h:91 Incorrect use of
kernel-doc format: * Enable the CDM module
Warning: drivers/gpu/drm/msm/disp/dpu1/dpu_hw_cdm.h:97 Incorrect use of
kernel-doc format: * Enable/disable the connection with pingpong
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695651/
Link: https://lore.kernel.org/r/20251219184638.1813181-4-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct and add kernel-doc comments to eliminate all warnings:
Warning: ../drivers/gpu/drm/msm/dp/dp_debug.h:31 expecting prototype for
msm_dp_debug_get(). Prototype was for msm_dp_debug_init() instead
Warning: ../drivers/gpu/drm/msm/dp/dp_drm.c:24 function parameter
'connector' not described in 'msm_dp_bridge_detect'
Warning: ../drivers/gpu/drm/msm/dp/dp_link.h:90 expecting prototype for
mdss_dp_test_bit_depth_to_bpp(). Prototype was for
msm_dp_link_bit_depth_to_bpp() instead
Warning: ../drivers/gpu/drm/msm/dp/dp_link.h:126 function parameter
'aux' not described in 'msm_dp_link_get'
Warning: ../drivers/gpu/drm/msm/dp/dp_link.h:126 function parameter
'dev' not described in 'msm_dp_link_get'
Warning: ../drivers/gpu/drm/msm/dp/dp_panel.h:70 function parameter
'bw_code' not described in 'is_link_rate_valid'
Warning: ../drivers/gpu/drm/msm/dp/dp_panel.h:84 expecting prototype for
msm_dp_link_is_lane_count_valid(). Prototype was for
is_lane_count_valid() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695647/
Link: https://lore.kernel.org/r/20251219184638.1813181-3-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
Correct and add kernel-doc comments to eliminate all warnings:
Warning: ../drivers/gpu/drm/msm/disp/mdp_format.h:27 This comment starts
with '/**', but isn't a kernel-doc comment.
Warning: ../drivers/gpu/drm/msm/disp/mdp_format.h:64 struct member
'bpc_a' not described in 'msm_format'
Warning: ../drivers/gpu/drm/msm/disp/mdp_format.h:64 struct member
'bpc_b_cb' not described in 'msm_format'
Warning: ../drivers/gpu/drm/msm/disp/mdp_format.h:64 struct member
'bpc_g_y' not described in 'msm_format'
Warning: ../drivers/gpu/drm/msm/disp/mdp_format.h:64 struct member
'bpc_r_cr' not described in 'msm_format'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/695650/
Link: https://lore.kernel.org/r/20251219184638.1813181-2-rdunlap@infradead.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Likely the last pull request in 2025, again a collection of lots of
small fixes. Most of them are various device-specific small fixes:
- An ASoC core fix for correcting the clamping behavior of *_SX mixer
elements
- Various fixes for ASoC fsl, SOF, etc
- Usual HD- and USB-audio quirks / fix-ups
- A couple of error-handling fixes for legacy PCMCIA drivers"
* tag 'sound-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda/realtek: fix PCI SSID for one of the HP 200 G2i laptop
ASoC: ops: fix snd_soc_get_volsw for sx controls
ALSA: hda/realtek: Add Asus quirk for TAS amplifiers
ASoC: Intel: soc-acpi-intel-mtl-match: Add 6 amp CS35L63 with feedback
ASoC: Intel: soc-acpi-intel-mtl-match: Add 6 amp CS35L56 with feedback
ASoC: fsl-asoc-card: Use of_property_present() for non-boolean properties
ASoC: rt1320: update VC blind write settings
ASoC: fsl_xcvr: provide regmap names
ASoC: fsl_sai: Add missing registers to cache default
ASoC: ak4458: remove the reset operation in probe and remove
ASoC: fsl_asrc_dma: fix duplicate debugfs directory error
ASoC: fsl_easrc: fix duplicate debugfs directory error
ALSA: hda/realtek: fix micmute LED reversed on HP Abe and Bantie
ALSA: hda/realtek: Add support for HP Clipper Laptop
ALSA: hda/realtek: Add support for HP Trekker Laptop
ALSA: usb-mixer: us16x08: validate meter packet indices
ASoC: Intel: soc-acpi-intel-nvl-match: Drop rt722 l3 from the match table
ASoC: soc-acpi / SOF: Add best_effort flag to get_function_tplg_files op
ASoC: SOF: Intel: pci-mtl: Change the topology path to intel/sof-ipc4-tplg
ASoC: SOF: ipc4-topology: set playback channel mask
...
|
|
Merge series from Mateusz Litwin <mateusz.litwin@nokia.com>:
On the Stratix10 platform, indirect reads can become very slow due to lost
interrupts and/or missed `complete()` calls, causing
`wait_for_completion_timeout()` to expire.
Three issues were identified:
1) A race condition exists between the read loop and IRQ `complete()`
call:
An IRQ can call `complete()` after the inner loop ends, but before
`reinit_completion()`, losing the completion event and leading to
`wait_for_completion_timeout()` expire. This function will not return
an error because `bytes_to_read` > 0 (indicating data is already in the
FIFO) and the final `ret` value is overwritten by
`cqspi_wait_for_bit()` return value (indicating request completion),
masking the timeout.
For test purpose, logging was added to print the count of timeouts and
the outer loop count.
$ dd if=/dev/mtd0 of=/dev/null bs=64M count=1
[ 2232.925219] cadence-qspi ff8d2000.spi: Indirect read error timeout
(1) loop (12472)
[ 2236.200391] cadence-qspi ff8d2000.spi: Indirect read error timeout
(1) loop (12460)
[ 2239.482836] cadence-qspi ff8d2000.spi: Indirect read error timeout
(5) loop (12450)
This indicates that such an event is rare, but possible.
Tested on the Stratix10 platform.
2) The quirk assumes the indirect read path never leaves the inner loop on
SoCFPGA. This assumption is incorrect when using slow flash. Disabling
IRQs in the inner loop can cause lost interrupts.
3) The `CQSPI_SLOW_SRAM` quirk disables `CQSPI_REG_IRQ_IND_COMP` (indirect
completion) interrupt, relying solely on the `CQSPI_REG_IRQ_WATERMARK`
(FIFO watermark) interrupt. For small transfers sizes, the final data
read might not fill the FIFO sufficiently to trigger the watermark,
preventing completion and leading to wait_for_completion_timeout()
expiration.
Two patches have been prepared to resolve these issues.
- [1/2] spi: cadence-quadspi: Prevent lost complete() call during
indirect read
Moving `reinit_completion()` before the inner loop prevents a race
condition. This might cause a premature IRQ complete() call to occur;
however, in the worst case, this will result in a spurious wakeup and
another wait cycle, which is preferable to waiting for a timeout.
- [2/2] spi: cadence-quadspi: Improve CQSPI_SLOW_SRAM quirk if flash is
slow
Re-enabling `CQSPI_REG_IRQ_IND_COMP` interrupt resolves the problem for
small reads and removes the disabling of interrupts, addressing the
issue with lost interrupts. This marginally increases the IRQ count.
Test:
$ dd if=/dev/mtd0 of=/dev/null bs=1M count=64
Results from the Stratix10 platform with mt25qu02g flash.
FIFO size in all tests: 128
Serviced interrupt call counts:
Without `CQSPI_SLOW_SRAM` quirk: 16 668 850
With `CQSPI_SLOW_SRAM` quirk: 204 176
With `CQSPI_SLOW_SRAM` and this patch: 224 528
Patch 2/2: Delivers a substantial read‑performance improvement for the
Cadence QSPI controller on the Stratix10 platform. Patch 1/2: Applies to
all platforms and should yield a modest performance gain, most noticeable
with large `CQSPI_READ_TIMEOUT_MS` values and workloads dominated by many
small reads.
|
|
There exists a null pointer dereference in simple_xattrs_free() as
part of the __kernfs_new_node() routine. Within __kernfs_new_node(),
err_out4 calls simple_xattr_free(), but kn->iattr may be NULL if
__kernfs_setattr() was never called. As a result, the first argument to
simple_xattrs_free() may be NULL + 0x38, and no NULL check is done
internally, causing an incorrect pointer dereference.
Add a check to ensure kn->iattr is not NULL, meaning __kernfs_setattr()
has been called and kn->iattr is allocated. Note that struct kernfs_node
kn is allocated with kmem_cache_zalloc, so we can assume kn->iattr will
be NULL if not allocated.
An alternative fix could be to not call simple_xattrs_free() at all. As
was previously discussed during the initial patch, simple_xattrs_free()
is not strictly needed and is included to be consistent with
kernfs_free_rcu(), which also helps the function maintain correctness if
changes are made in __kernfs_new_node().
Reported-by: syzbot+6aaf7f48ae034ab0ea97@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6aaf7f48ae034ab0ea97
Fixes: 382b1e8f30f7 ("kernfs: fix memory leak of kernfs_iattrs in __kernfs_new_node")
Signed-off-by: Will Rosenberg <whrosenb@asu.edu>
Link: https://patch.msgid.link/20251217060107.4171558-1-whrosenb@asu.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johan Hovold <johan@kernel.org> says:
The new buffer management code has not been tested or reviewed properly
and breaks boot of machines like the Lenovo ThinkPad X13s.
Fixing this will require designing a proper interface for managing these
transactions, something which most likely involves reverting most of the
offending commit anyway.
Revert the broken code to fix the regression and let Intel come up with
a properly tested implementation for a later kernel.
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
message out fields"
This reverts commit 3e082978c33151d576694deac8abde021ea669a8.
The new buffer management code has not been tested or reviewed properly
and breaks boot of machines like the Lenovo ThinkPad X13s:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000000
CPU: 0 UID: 0 PID: 813 Comm: kworker/0:3 Not tainted 6.19.0-rc2 #26 PREEMPT
Hardware name: LENOVO 21BYZ9SRUS/21BYZ9SRUS, BIOS N3HET87W (1.59 ) 12/05/2023
Workqueue: events ucsi_handle_connector_change [typec_ucsi]
Call trace:
ucsi_sync_control_common+0xe4/0x1ec [typec_ucsi] (P)
ucsi_run_command+0xcc/0x194 [typec_ucsi]
ucsi_send_command_common+0x84/0x2a0 [typec_ucsi]
ucsi_get_connector_status+0x48/0x78 [typec_ucsi]
ucsi_handle_connector_change+0x5c/0x4f4 [typec_ucsi]
process_one_work+0x208/0x60c
worker_thread+0x244/0x388
The new code completely ignores concurrency so that the message length
can be updated while a transaction is ongoing. In the above case, the
length ends up being modified by another thread while processing an ack
so that the NULL cci pointer is dereferenced.
Fixing this will require designing a proper interface for managing these
transactions, something which most likely involves reverting most of the
offending commit anyway.
Revert the broken code to fix the regression and let Intel come up with
a properly tested implementation for a later kernel.
Fixes: 3e082978c331 ("usb: typec: ucsi: Update UCSI structure to have message in and message out fields")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-5-johan@kernel.org
|
|
This reverts commit db0028637cc832add6d87564fcc2ebb12781b046.
The new buffer management code that this feature relies on is broken so
revert for now.
As for the in buffer, nothing prevents the out message size and buffer
from being modified while the message is being processed due to lack of
serialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-4-johan@kernel.org
|
|
This reverts commit 775fae520e6ae62c393a8daf42dc534f09692f3f.
The new buffer management code that this relies on is broken so revert
for now.
It also looks like the error handling needs some more thought as the
message out size is not reset on errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-3-johan@kernel.org
|
|
This reverts commit 1b474ee01fbb73b1365adbf9b3067f7375e471ee.
The new buffer management code that this feature relies on is broken so
revert for now.
The interface for writing data and support for UCSI_SET_PDOS looks like
it could use some more thought as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251222152204.2846-2-johan@kernel.org
|
|
ucsi_sync_control_common"
This reverts commit 14ad4c10d5bdd413ff9a914260e89b5f54b7a2c7.
The originally offending commit will be reverted instead of this fix up
at this point in time, so revert this fix.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Mario Limonciello (AMD) <superm1@kernel.org>
Cc: stable <stable@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Fixes: 14ad4c10d5bd ("usb: typec: ucsi: Fix null pointer dereference in ucsi_sync_control_common")
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5106dbab44fba8ec6dede3f4e75d17f5aa777ec8.
There are reported issues in this file, so revert the commit for now so
that the original offending changes can be reverted and working systems
can be restored. This can come back at a later time if it is rebased
yet-again (sorry.)
Cc: stable <stable@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20251222152204.2846-1-johan@kernel.org
Fixes: 5106dbab44fb ("usb: typec: ucsi: Get connector status after enable notifications")
Cc: Kenneth R. Crudup <kenny@panix.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hsin-Te Yuan <yuanhsinte@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Error labels should be named after what they do rather than after from
where they are jumped to.
Rename the probe error labels for consistency and to improve
readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Error labels should be named after what they do rather than after from
where they are jumped to.
Rename the probe error labels for consistency and to improve
readability.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to drop the reference taken when looking up the PHY I2C device
during probe on probe failure (e.g. probe deferral) and on driver
unbind.
Fixes: 73108aa90cbf ("USB: ohci-nxp: Use isp1301 driver")
Cc: stable@vger.kernel.org # 3.5
Reported-by: Ma Ke <make24@iscas.ac.cn>
Link: https://lore.kernel.org/lkml/20251117013428.21840-1-make24@iscas.ac.cn/
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent change fixing a device reference leak in a UDC driver
introduced a potential use-after-free in the non-OF case as the
isp1301_get_client() helper only increases the reference count for the
returned I2C device in the OF case.
Increment the reference count also for non-OF so that the caller can
decrement it unconditionally.
Note that this is inherently racy just as using the returned I2C device
is since nothing is preventing the PHY driver from being unbound while
in use.
Fixes: c84117912bdd ("USB: lpc32xx_udc: Fix error handling in probe")
Cc: stable@vger.kernel.org
Cc: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent change fixing a device reference leak introduced a clock
imbalance by reusing an error path so that the clock may be disabled
before having been enabled.
Note that the clock framework allows for passing in NULL clocks so there
is no risk for a NULL pointer dereference.
Also drop the bogus I2C client NULL check added by the offending commit
as the pointer has already been verified to be non-NULL.
Fixes: c84117912bdd ("USB: lpc32xx_udc: Fix error handling in probe")
Cc: stable@vger.kernel.org
Cc: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20251218153519.19453-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Originally, the notification for connector change will be enabled after
the first read of the connector status. Therefore, if the event happens
during this window, it will be missing and make the status unsynced.
Get the connector status only after enabling the notification for
connector change to ensure the status is synced.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: stable <stable@kernel.org>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Link: https://patch.msgid.link/20251218-ucsi-v7-1-aea83e83fb12@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We cannot determine which models require the NO_ATA_1X and
IGNORE_RESIDUE quirks aside from the EL-R12 optical drive device.
Fixes: 955a48a5353f ("usb: usb-storage: No additional quirks need to be added to the EL-R12 optical drive.")
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Link: https://patch.msgid.link/20251218012318.15978-1-chenchangcheng@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CQSPI_SLOW_SRAM quirk on the Stratix10 platform causes fewer interrupts,
but also causes timeouts if a small block is used or if flash devices are
slower than or equal in speed to SRAM's read operations. Adding the
CQSPI_REG_IRQ_IND_COMP interrupt would resolve the problem for small
reads, and removing the disabling of interrupts would resolve the issue
with lost interrupts.
This marginally increases IRQ count. Tests show that this will cause only
a few percent more interrupts.
Test:
$ dd if=/dev/mtd0 of=/dev/null bs=1M count=64
Results from the Stratix10 platform with mt25qu02g flash.
FIFO size in all tests: 128
Serviced interrupt call counts:
Without CQSPI_SLOW_SRAM quirk: 16 668 850
With CQSPI_SLOW_SRAM quirk: 204 176
With CQSPI_SLOW_SRAM and this commit: 224 528
Signed-off-by: Mateusz Litwin <mateusz.litwin@nokia.com>
Link: https://patch.msgid.link/20251218-cqspi_indirect_read_improve-v2-2-396079972f2a@nokia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A race condition exists between the read loop and IRQ `complete()` call.
An interrupt could call the complete() between the inner loop and
reinit_completion(), potentially losing the completion event and causing
an unnecessary timeout. Moving reinit_completion() before the loop
prevents this. A premature signal will only result in a spurious wakeup
and another wait cycle, which is preferable to waiting for a timeout.
Signed-off-by: Mateusz Litwin <mateusz.litwin@nokia.com>
Link: https://patch.msgid.link/20251218-cqspi_indirect_read_improve-v2-1-396079972f2a@nokia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
