| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- Simon Glass wanted to support binman's output properties in order
to check their validity using the binding checks and proposed
changes with the missing properties as well as a binman compatible.
- Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
- The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
- Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
Raw NAND subsystem:
- Two small fixes, one in the Hynix vendor code for properly
returning an error which might have been ignored and another in the
Davinci driver to properly synchronize the controller with the gpio
domain.
SPI NOR subsystem:
- SPI NOR now uses div_u64() instead of div64_u64() in places where
the divisor is 32 bits. Many 32 bit architectures can optimize this
variant better than a full 64 bit divide"
* tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: replace unnecessary div64_u64() with div_u64()
mtd: mchp23k256: drop unneeded MODULE_ALIAS
dt-bindings: mtd: fixed-partition: Add binman compatibles
dt-bindings: mtd: fixed-partitions: Add alignment properties
mtd: maps: sa1100-flash: Prefer struct_size over open coded arithmetic
mtd: core: Align comment with an action in mtd_otp_nvmem_add()
mtd: rawnand: hynix: fixed typo
mtd: rawnand: davinci: Add dummy read after sending command
mtd: partitions: redboot: Added conversion of operands to a larger type
dt-bindings: mtd: Add Samsung S5Pv210 OneNAND
mtd: core: Don't fail mtd_otp_nvmem_add() if OTP is unsupported
mtd: core: Report error if first mtd_otp_size() call fails in mtd_otp_nvmem_add()
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Increase the timeout period of the ACMD41 command
- Add card entry for quirks to debugfs
- Add mmc_gpiod_set_cd_config() function
- Store owner from SDIO modules with sdio_register_driver()
MMC host:
- atmel-mci: Some cleanups and a switch to use dev_err_probe()
- renesas_sdhi:
- Add support for RZ/G2L, RZ/G3S and RZ/V2M variants
- Set the SDBUF after reset
- sdhci: Add support for "Tuning Error" interrupts
- sdhci-acpi:
- Add quirk to enable pull-up on the card-detect GPIO on Asus
T100TA
- Disable write protect detection on Toshiba WT10-A
- Fix Lenovo Yoga Tablet 2 Pro 1380 sdcard slot not working
- sdhci_am654:
- Re-work and fix the tuning support for multiple speed-modes
- Add tuning algorithm for delay chain
- sdhci-esdhc-imx: Add NXP S32G3 support
- sdhci-of-dwcmshc:
- Add tuning support for Sophgo CV1800B and SG200X
- Implement SDHCI CQE support
- sdhci-pci-gli: Use the proper pci_set_power_state() instead of
PMCSR writes"
MEMSTICK:
- Convert a couple of drivers to use the ->remove_new() callback"
* tag 'mmc-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: renesas_sdhi: Add compatible string for RZ/G2L family, RZ/G3S, and RZ/V2M SoCs
dt-bindings: mmc: renesas,sdhi: Document RZ/G2L family compatibility
dt-bindings: mmc: renesas,sdhi: Group single const value items into an enum list
mmc: renesas_sdhi: Set the SDBUF after reset
mmc: core: Increase the timeout period of the ACMD41 command
mmc: core: Convert to use __mmc_poll_for_busy() SD_APP_OP_COND too
mmc: atmel-mci: Switch to use dev_err_probe()
mmc: atmel-mci: Incapsulate used to be a platform data into host structure
mmc: atmel-mci: Replace platform device pointer by generic one
mmc: atmel-mci: Use temporary variable for struct device
mmc: atmel-mci: Get rid of platform data leftovers
mmc: sdhci-of-dwcmshc: Add tuning support for Sophgo CV1800B and SG200X
mmc: sdhci-of-dwcmshc: Remove useless "&" of th1520_execute_tuning
mmc: sdhci-s3c: Choose sdhci_ops based on variant
mmc: sdhci_am654: Constify struct sdhci_ops
mmc: sdhci-sprd: Constify struct sdhci_ops
mmc: sdhci-omap: Constify struct sdhci_ops
mmc: sdhci-esdhc-mcf: Constify struct sdhci_ops
mmc: slot-gpio: Use irq_handler_t type
mmc: sdhci-acpi: Add quirk to enable pull-up on the card-detect GPIO on Asus T100TA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Don't clear suspended_count at genpd_prepare()
- Update the rejected/usage counters at system suspend too
pmdomain providers:
- ti-sci: Fix duplicate PD referrals
- mediatek: Add MT8188 buck isolation setting
- renesas: Add R-Car M3-W power-off delay quirk
- renesas: Split R-Car M3-W and M3-W+ sub-drivers
cpuidle-psci:
- Update MAINTAINERS to set a git for DT IDLE PM DOMAIN/ARM PSCI PM
DOMAIN
- Update init level to core_initcall()
- Drop superfluous wrappers psci_dt_attach|detach_cpu()"
* tag 'pmdomain-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: ti-sci: Fix duplicate PD referrals
pmdomain: core: Don't clear suspended_count at genpd_prepare()
pmdomain: core: Update the rejected/usage counters at system suspend too
pmdomain: renesas: rcar-sysc: Add R-Car M3-W power-off delay quirk
pmdomain: renesas: rcar-sysc: Remove rcar_sysc_nullify() helper
pmdomain: renesas: rcar-sysc: Split R-Car M3-W and M3-W+ sub-drivers
pmdomain: renesas: rcar-sysc: Absorb rcar_sysc_ch into rcar_sysc_pd
MAINTAINERS: Add a git for the DT IDLE PM DOMAIN
MAINTAINERS: Add a git for the ARM PSCI PM DOMAIN
cpuidle: psci: Update init level to core_initcall()
cpuidle: psci: Drop superfluous wrappers psci_dt_attach|detach_cpu()
pmdomain: mediatek: Add MT8188 buck isolation setting
pmdomain: mediatek: scpsys: drop driver owner assignment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New V4L2 ioctl VIDIOC_REMOVE_BUFS
- experimental support for using generic metaformats on V4L2 core
- New drivers: Intel IPU6 controller driver, Broadcom BCM283x/BCM271x
- More cleanups at atomisp driver
- Usual bunch of driver cleanups, improvements and fixes
* tag 'media/v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (328 commits)
media: bcm2835-unicam: Depend on COMMON_CLK
Revert "media: v4l2-ctrls: show all owned controls in log_status"
media: ov2740: Ensure proper reset sequence on probe()
media: intel/ipu6: Don't print user-triggerable errors to kernel log
media: bcm2835-unicam: Fix driver path in MAINTAINERS
media: bcm2835-unicam: Fix a NULL vs IS_ERR() check
media: bcm2835-unicam: Do not print error when irq not found
media: bcm2835-unicam: Do not replace IRQ retcode during probe
media: bcm2835-unicam: Convert to platform remove callback returning void
media: media: intel/ipu6: Fix spelling mistake "remappinp" -> "remapping"
media: intel/ipu6: explicitly include vmalloc.h
media: cec.h: Fix kerneldoc
media: uvcvideo: Refactor iterators
media: v4l: async: refactor v4l2_async_create_ancillary_links
media: intel/ipu6: Don't re-allocate memory for firmware
media: dvb-frontends: tda10048: Fix integer overflow
media: tc358746: Use the correct div_ function
media: i2c: st-mipid02: Use the correct div function
media: tegra-vde: Refactor timeout handling
media: stk1160: Use min macro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL updates from Dave Jiang:
- Three CXL mailbox passthrough commands are added to support the
populating and clearing of vendor debug logs:
- Get Log Capabilities
- Get Supported Log Sub-List Commands
- Clear Log
- Add support of Device Phyiscal Address (DPA) to Host Physical Address
(HPA) translation for CXL events of cxl_dram and cxl_general media.
This allows user space to figure out which CXL region the event
occured via trace event.
- Connect CXL to CPER reporting.
If a device is configured for firmware first, CXL event records are
not sent directly to the host. Those records are reported through EFI
Common Platform Error Records (CPER). Add support to route the CPER
records through the CXL sub-system in order to provide DPA to HPA
translation and also event decoding and tracing. This is useful for
users to determine which system issues may correspond to specific
hardware events.
- A number of misc cleanups and fixes:
- Fix for compile warning of cxl_security_ops
- Add debug message for invalid interleave granularity
- Enhancement to cxl-test event testing
- Add dev_warn() on unsupported mixed mode decoder
- Fix use of phys_to_target_node() for x86
- Use helper function for decoder enum instead of open coding
- Include missing headers for cxl-event
- Fix MAINTAINERS file entry
- Fix cxlr_pmem memory leak
- Cleanup __cxl_parse_cfmws via scope-based resource menagement
- Convert cxl_pmem_region_alloc() to scope-based resource management
* tag 'cxl-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (21 commits)
cxl/cper: Remove duplicated GUID defines
cxl/cper: Fix non-ACPI-APEI-GHES build
cxl/pci: Process CPER events
acpi/ghes: Process CXL Component Events
cxl/region: Convert cxl_pmem_region_alloc to scope-based resource management
cxl/acpi: Cleanup __cxl_parse_cfmws()
cxl/region: Fix cxlr_pmem leaks
cxl/core: Add region info to cxl_general_media and cxl_dram events
cxl/region: Move cxl_trace_hpa() work to the region driver
cxl/region: Move cxl_dpa_to_region() work to the region driver
cxl/trace: Correct DPA field masks for general_media & dram events
MAINTAINERS: repair file entry in COMPUTE EXPRESS LINK
cxl/cxl-event: include missing <linux/types.h> and <linux/uuid.h>
cxl/hdm: Debug, use decoder name function
cxl: Fix use of phys_to_target_node() for x86
cxl/hdm: dev_warn() on unsupported mixed mode decoder
cxl/test: Enhance event testing
cxl/hdm: Add debug message for invalid interleave granularity
cxl: Fix compile warning for cxl_security_ops extern
cxl/mbox: Add Clear Log mailbox command
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm updates from Ira Weiny:
"The changes include removing duplicate code and updating the nvdimm
tree to the current kernel interfaces such as using const for struct
device_type and changing the platform remove callback signature"
* tag 'libnvdimm-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: remove redundant assignment to variable rc
ndtest: Convert to platform remove callback returning void
nvdimm/btt: always set max_integrity_segments
nvdimm: remove nd_integrity_init
dax: constify the struct device_type usage
powerpc/papr_scm: Move duplicate definitions to common header files
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This one became bigger than usual, not in the total size but rather
containing lots of small changes all over the places.
The majority of changes are about ASoC, especially SOF / Intel stuff,
and we see an interesting work for ASoC DAPM graph visualization,
while there are many other code cleanup and refactoring, too.
Core:
- A deadlock fix at device disconnection
- A new tool dapm-graph for visualising the DAPM state
ASoC:
- Large updates throughout the Intel audio drivers
- Fixes and clarifications for the DAPM documentation
- Cleanups of accessors for driver data, module labelling, and for
constification
- Modernsation and cleanup work in the Mediatek drivers
- Several fixes and features for the DaVinci I2S driver
- New drivers for several AMD and Intel platforms, Nuvoton NAU8325,
Rockchip RK3308 and Texas Instruments PCM6240
HD-audio:
- Cleanup for CONFIG_PM dependencies
- Cirrus HD-audio codec fixes and quirks
Others:
- Series of tree-wide fixes in Makefiles to use *-y
- Additions of missing module descriptions
- Scarlett2 USB mixer enhancements
- A series of legacy emu10k1 fixes and improvements"
* tag 'sound-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (603 commits)
ALSA: hda/realtek: Drop doubly quirk entry for 103c:8a2e
ALSA: hda/realtek - fixed headset Mic not show
ASoC: SOF: amd: Fix build error with built-in config
ALSA: scarlett2: Increase mixer range to +12dB
ALSA: scarlett2: Add S/PDIF source selection controls
ALSA: core: Remove superfluous CONFIG_PM
ALSA: Fix deadlocks with kctl removals at disconnection
ASoC: audio-graph-card2: call of_node_get() before of_get_next_child()
ASoC: SOF: amd: Correct spaces in Makefile
ASoC: rt715-sdca-sdw: Fix wrong complete waiting in rt715_dev_resume()
ASoC: Intel: sof_sdw_rt_amp: use dai parameter
ASoC: Intel: sof_sdw: add dai parameter to rtd_init callback
ASoC: Intel: sof_sdw: use .controls/.widgets to add controls/widgets
ASoC: Intel: sof_sdw: add controls and dapm widgets in codec_info
ASoC: Intel: sof_sdw: use generic name for controls/widgets
ASoC: Intel: sof_sdw_cs_amp: rename Speakers to Speaker
ASoC: Intel: maxim-common: change max98373 data to static
ASoC: Intel: sof_sdw: add max98373 dapm routes
ASoC: Intel: sof_rt5682: use max_98373_dai_link function
ASoC: Intel: sof_nau8825: use max_98373_dai_link function
...
|
|
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm subsystems for 6.10.
In drivers the main thing is a new driver for ARM Mali firmware based
GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
scattered changes to everything else.
In the core a bunch of headers and Kconfig was refactored, along with
the addition of a new panic handler which is meant to provide a user
friendly message when a panic happens and graphical display is
enabled.
New drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
Core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing"
* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
drm/xe/ads: Use flexible-array
drm/xe: Use ordered WQ for G2H handler
drm/msm/gen_header: allow skipping the validation
drm/msm/a6xx: Cleanup indexed regs const'ness
drm/msm: Add devcoredump support for a750
drm/msm: Adjust a7xx GBIF debugbus dumping
drm/msm: Update a6xx registers XML
drm/msm: Fix imported a750 snapshot header for upstream
drm/msm: Import a750 snapshot registers from kgsl
MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
drm/msm/adreno: fix CP cycles stat retrieval on a7xx
drm/msm/a7xx: allow writing to CP_BV counter selection registers
drm: zynqmp_dpsub: Always register bridge
Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
drm/fbdev-generic: Do not set physical framebuffer address
drm/panthor: Fix the FW reset logic
drm/panthor: Make sure we handle 'unknown group state' case properly
...
|
|
Zi Shen Lim is not actively doing kernel development and has decided to
tranfer the responsibility of maintaining the JIT to me.
Add myself as the maintainer for BPF JIT for ARM64 and remove Zi Shen
Lim.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Link: https://lore.kernel.org/r/20240514183914.27737-1-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm updates from Paul Moore:
- The security/* portion of the effort to remove the empty sentinel
elements at the end of the ctl_table arrays
- Update the file list associated with the LSM / "SECURITY SUBSYSTEM"
entry in the MAINTAINERS file (and then fix a typo in then update)
* tag 'lsm-pr-20240513' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
MAINTAINERS: repair file entry in SECURITY SUBSYSTEM
MAINTAINERS: update the LSM file list
lsm: remove the now superfluous sentinel element from ctl_table array
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Complete rework of garbage collection of AF_UNIX sockets.
AF_UNIX is prone to forming reference count cycles due to fd
passing functionality. New method based on Tarjan's Strongly
Connected Components algorithm should be both faster and remove a
lot of workarounds we accumulated over the years.
- Add TCP fraglist GRO support, allowing chaining multiple TCP
packets and forwarding them together. Useful for small switches /
routers which lack basic checksum offload in some scenarios (e.g.
PPPoE).
- Support using SMP threads for handling packet backlog i.e. packet
processing from software interfaces and old drivers which don't use
NAPI. This helps move the processing out of the softirq jumble.
- Continue work of converting from rtnl lock to RCU protection.
Don't require rtnl lock when reading: IPv6 routing FIB, IPv6
address labels, netdev threaded NAPI sysfs files, bonding driver's
sysfs files, MPLS devconf, IPv4 FIB rules, netns IDs, tcp metrics,
TC Qdiscs, neighbor entries, ARP entries via ioctl(SIOCGARP), a lot
of the link information available via rtnetlink.
- Small optimizations from Eric to UDP wake up handling, memory
accounting, RPS/RFS implementation, TCP packet sizing etc.
- Allow direct page recycling in the bulk API used by XDP, for +2%
PPS.
- Support peek with an offset on TCP sockets.
- Add MPTCP APIs for querying last time packets were received/sent/acked
and whether MPTCP "upgrade" succeeded on a TCP socket.
- Add intra-node communication shortcut to improve SMC performance.
- Add IPv6 (and IPv{4,6}-over-IPv{4,6}) support to the GTP protocol
driver.
- Add HSR-SAN (RedBOX) mode of operation to the HSR protocol driver.
- Add reset reasons for tracing what caused a TCP reset to be sent.
- Introduce direction attribute for xfrm (IPSec) states. State can be
used either for input or output packet processing.
Things we sprinkled into general kernel code:
- Add bitmap_{read,write}(), bitmap_size(), expose BYTES_TO_BITS().
This required touch-ups and renaming of a few existing users.
- Add Endian-dependent __counted_by_{le,be} annotations.
- Make building selftests "quieter" by printing summaries like
"CC object.o" rather than full commands with all the arguments.
Netfilter:
- Use GFP_KERNEL to clone elements, to deal better with OOM
situations and avoid failures in the .commit step.
BPF:
- Add eBPF JIT for ARCv2 CPUs.
- Support attaching kprobe BPF programs through kprobe_multi link in
a session mode, meaning, a BPF program is attached to both function
entry and return, the entry program can decide if the return
program gets executed and the entry program can share u64 cookie
value with return program. "Session mode" is a common use-case for
tetragon and bpftrace.
- Add the ability to specify and retrieve BPF cookie for raw
tracepoint programs in order to ease migration from classic to raw
tracepoints.
- Add an internal-only BPF per-CPU instruction for resolving per-CPU
memory addresses and implement support in x86, ARM64 and RISC-V
JITs. This allows inlining functions which need to access per-CPU
state.
- Optimize x86 BPF JIT's emit_mov_imm64, and add support for various
atomics in bpf_arena which can be JITed as a single x86
instruction. Support BPF arena on ARM64.
- Add a new bpf_wq API for deferring events and refactor
process-context bpf_timer code to keep common code where possible.
- Harden the BPF verifier's and/or/xor value tracking.
- Introduce crypto kfuncs to let BPF programs call kernel crypto
APIs.
- Support bpf_tail_call_static() helper for BPF programs with GCC 13.
- Add bpf_preempt_{disable,enable}() kfuncs in order to allow a BPF
program to have code sections where preemption is disabled.
Driver API:
- Skip software TC processing completely if all installed rules are
marked as HW-only, instead of checking the HW-only flag rule by
rule.
- Add support for configuring PoE (Power over Ethernet), similar to
the already existing support for PoDL (Power over Data Line)
config.
- Initial bits of a queue control API, for now allowing a single
queue to be reset without disturbing packet flow to other queues.
- Common (ethtool) statistics for hardware timestamping.
Tests and tooling:
- Remove the need to create a config file to run the net forwarding
tests so that a naive "make run_tests" can exercise them.
- Define a method of writing tests which require an external endpoint
to communicate with (to send/receive data towards the test
machine). Add a few such tests.
- Create a shared code library for writing Python tests. Expose the
YAML Netlink library from tools/ to the tests for easy Netlink
access.
- Move netfilter tests under net/, extend them, separate performance
tests from correctness tests, and iron out issues found by running
them "on every commit".
- Refactor BPF selftests to use common network helpers.
- Further work filling in YAML definitions of Netlink messages for:
nftables, team driver, bonding interfaces, vlan interfaces, VF
info, TC u32 mark, TC police action.
- Teach Python YAML Netlink to decode attribute policies.
- Extend the definition of the "indexed array" construct in the specs
to cover arrays of scalars rather than just nests.
- Add hyperlinks between definitions in generated Netlink docs.
Drivers:
- Make sure unsupported flower control flags are rejected by drivers,
and make more drivers report errors directly to the application
rather than dmesg (large number of driver changes from Asbjørn
Sloth Tønnesen).
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support multiple RSS contexts and steering traffic to them
- support XDP metadata
- make page pool allocations more NUMA aware
- Intel (100G, ice, idpf):
- extract datapath code common among Intel drivers into a library
- use fewer resources in switchdev by sharing queues with the PF
- add PFCP filter support
- add Ethernet filter support
- use a spinlock instead of HW lock in PTP clock ops
- support 5 layer Tx scheduler topology
- nVidia/Mellanox:
- 800G link modes and 100G SerDes speeds
- per-queue IRQ coalescing configuration
- Marvell Octeon:
- support offloading TC packet mark action
- Ethernet NICs consumer, embedded and virtual:
- stop lying about skb->truesize in USB Ethernet drivers, it
messes up TCP memory calculations
- Google cloud vNIC:
- support changing ring size via ethtool
- support ring reset using the queue control API
- VirtIO net:
- expose flow hash from RSS to XDP
- per-queue statistics
- add selftests
- Synopsys (stmmac):
- support controllers which require an RX clock signal from the
MII bus to perform their hardware initialization
- TI:
- icssg_prueth: support ICSSG-based Ethernet on AM65x SR1.0 devices
- icssg_prueth: add SW TX / RX Coalescing based on hrtimers
- cpsw: minimal XDP support
- Renesas (ravb):
- support describing the MDIO bus
- Realtek (r8169):
- add support for RTL8168M
- Microchip Sparx5:
- matchall and flower actions mirred and redirect
- Ethernet switches:
- nVidia/Mellanox:
- improve events processing performance
- Marvell:
- add support for MV88E6250 family internal PHYs
- Microchip:
- add DCB and DSCP mapping support for KSZ switches
- vsc73xx: convert to PHYLINK
- Realtek:
- rtl8226b/rtl8221b: add C45 instances and SerDes switching
- Many driver changes related to PHYLIB and PHYLINK deprecated API
cleanup
- Ethernet PHYs:
- Add a new driver for Airoha EN8811H 2.5 Gigabit PHY.
- micrel: lan8814: add support for PPS out and external timestamp trigger
- WiFi:
- Disable Wireless Extensions (WEXT) in all Wi-Fi 7 devices
drivers. Modern devices can only be configured using nl80211.
- mac80211/cfg80211
- handle color change per link for WiFi 7 Multi-Link Operation
- Intel (iwlwifi):
- don't support puncturing in 5 GHz
- support monitor mode on passive channels
- BZ-W device support
- P2P with HE/EHT support
- re-add support for firmware API 90
- provide channel survey information for Automatic Channel Selection
- MediaTek (mt76):
- mt7921 LED control
- mt7925 EHT radiotap support
- mt7920e PCI support
- Qualcomm (ath11k):
- P2P support for QCA6390, WCN6855 and QCA2066
- support hibernation
- ieee80211-freq-limit Device Tree property support
- Qualcomm (ath12k):
- refactoring in preparation of multi-link support
- suspend and hibernation support
- ACPI support
- debugfs support, including dfs_simulate_radar support
- RealTek:
- rtw88: RTL8723CS SDIO device support
- rtw89: RTL8922AE Wi-Fi 7 PCI device support
- rtw89: complete features of new WiFi 7 chip 8922AE including
BT-coexistence and Wake-on-WLAN
- rtw89: use BIOS ACPI settings to set TX power and channels
- rtl8xxxu: enable Management Frame Protection (MFP) support
- Bluetooth:
- support for Intel BlazarI and Filmore Peak2 (BE201)
- support for MediaTek MT7921S SDIO
- initial support for Intel PCIe BT driver
- remove HCI_AMP support"
* tag 'net-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1827 commits)
selftests: netfilter: fix packetdrill conntrack testcase
net: gro: fix napi_gro_cb zeroed alignment
Bluetooth: btintel_pcie: Refactor and code cleanup
Bluetooth: btintel_pcie: Fix warning reported by sparse
Bluetooth: hci_core: Fix not handling hdev->le_num_of_adv_sets=1
Bluetooth: btintel: Fix compiler warning for multi_v7_defconfig config
Bluetooth: btintel_pcie: Fix compiler warnings
Bluetooth: btintel_pcie: Add *setup* function to download firmware
Bluetooth: btintel_pcie: Add support for PCIe transport
Bluetooth: btintel: Export few static functions
Bluetooth: HCI: Remove HCI_AMP support
Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
Bluetooth: qca: Fix error code in qca_read_fw_build_info()
Bluetooth: hci_conn: Use __counted_by() and avoid -Wfamnae warning
Bluetooth: btintel: Add support for Filmore Peak2 (BE201)
Bluetooth: btintel: Add support for BlazarI
LE Create Connection command timeout increased to 20 secs
dt-bindings: net: bluetooth: Add MediaTek MT7921S SDIO Bluetooth
Bluetooth: compute LE flow credits based on recvbuf space
Bluetooth: hci_sync: Use cmd->num_cis instead of magic number
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski
"This was a quiet release cycle for the GPIO tree and so this
pull-request is relatively small.
We have one new driver, some minor improvements to the GPIO core code
and across several drivers, some DT and documentation updates but in
general nothing stands out or is controversial. All changes have spent
time in next with no reported issues (or ones that were quickly
fixed).
GPIO core:
- remove more unused legacy interfaces (after converting the last
remaining users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name
fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple
GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to
gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos"
* tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (30 commits)
gpio: nuvoton: Fix sgpio irq handle error
gpiolib: Discourage to use formatting strings in line names
gpio: brcmstb: add support for gpio-ranges
gpio: of: support gpio-ranges for multiple gpiochip devices
dt-bindings: gpio: brcmstb: add gpio-ranges
gpio: Add Intel Granite Rapids-D vGPIO driver
gpio: brcmstb: Use dynamic GPIO base numbers
gpiolib: acpi: Set label for IRQ only lines
gpiolib: acpi: Add fwnode name to the GPIO interrupt label
gpiolib: Get rid of never false gpio_is_valid() calls
gpiolib: acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
gpiolib: acpi: Simplify error handling in __acpi_find_gpio()
gpiolib: acpi: Extract __acpi_find_gpio() helper
gpio: sch: Utilise temporary variable for struct device
gpio: sch: Switch to memory mapped IO accessors
gpio: regmap: Use -ENOTSUPP consistently
gpio: pcie-idio-24: Use -ENOTSUPP consistently
Documentation: gpio: Replace leading TABs by spaces in code blocks
gpiolib: acpi: Check for errors first in acpi_find_gpio()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon XDP710
- EC Chip driver for Lenovo ThinkStation motherboards
- Analog Devices ADP1050
Improved support for existing drivers:
- emc1403: Convert to with_info API; Support for EMC1428 and EMC1438
- nzxt-kraken3: Support for NZXT Kraken 2023
- aquacomputer_d5next: Support for Octo flow sensors
- pmbus/adm1275: Support for ADM1281
- dell-smm: Supportt for Precision 7540 and G5 5505
Other notable cleanup:
- max6639: Use regmap
- Remove unused structure fields from multiple drivers
- Drop explicit initialization of struct i2c_device_id::driver_data
to zero
- Improve configuration mode handling in it87 driver
- jc42: Drop support for I2C_CLASS_SPD
- Various conversions to devicetree schema
- Add HAS_IOPORT dependencies as needed
Minor fixes and improvements to max31790, coretemp, aspeed-g6-pwm-tach,
pwm-fan, pmbus/mp2975, acpi_power_meter, and lm70 drivers"
* tag 'hwmon-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (52 commits)
hwmon: (nzxt-kraken3) Bail out for unsupported device variants
hwmon: (emc1403) Add support for EMC1428 and EMC1438.
hwmon: Drop explicit initialization of struct i2c_device_id::driver_data to 0 (part 2)
hwmon: (emc1403) Add support for conversion interval configuration
hwmon: (emc1403) Support 11 bit accuracy
hwmon: (emc1403) Convert to with_info API
hwmon: (max6639) Use regmap
hwmon: (npcm750-pwm-fan) Remove another unused field in struct npcm7xx_cooling_device
hwmon: (npcm750-pwm-fan) Remove an unused field in struct npcm7xx_cooling_device
hwmon: (stts751) Remove an unused field in struct stts751_priv
hwmon: Drop explicit initialization of struct i2c_device_id::driver_data to 0
hwmon: (max31790) revise the scale to write pwm
hwmon: (nzxt-kraken3) Add support for NZXT Kraken 2023 (standard and Elite) models
hwmon: (nzxt-kraken3) Decouple device names from kinds
hwmon: (it87) Remove tests nolonger required
hwmon: (it87) Test for chipset before entering configuration mode
hwmon: (it87) Do not enter configuration mode for some chiptypes
hwmon: (it87) Rename FEAT_CONF_NOEXIT to FEAT_NOCONF as more descriptive of requirement
hwmon: (pmbus) Add support for Infineon XDP710
dt-bindings: hwmon: Add infineon xdp710 driver bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The diffstat for this release is dominated by the new Airoha driver,
mainly as a result of this being a generally quite quiet release.
There were a couple of cleanups in the core but nothing substantial,
the updates here are almost all driver specific ones.
- Support for multi-word mode in the OMAP2 McSPI driver
- Overhaul of the PXA2xx driver, mostly API updates
- A number of DT binding conversions
- Support for Airoha NAND controllers, Cirrus Logic CS35L56, Mobileye
EYEQ5 and Renesas R8A779H0"
* tag 'spi-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: dw: Bail out early on unsupported target mode
spi: Remove unneded check for orig_nents
MAINTAINERS: repair file entry in AIROHA SPI SNFI DRIVER
spi: pxa2xx: Drop the stale entry in documentation TOC
spi: pxa2xx: Don't provide struct chip_data for others
spi: pxa2xx: Remove timeout field from struct chip_data
spi: pxa2xx: Remove DMA parameters from struct chip_data
spi: pxa2xx: Drop struct pxa2xx_spi_chip
spi: pxa2xx: Don't use "proxy" headers
spi: pxa2xx: Remove outdated documentation
spi: pxa2xx: Move contents of linux/spi/pxa2xx_spi.h to a local one
spi: pxa2xx: Provide num-cs for Sharp PDAs via device properties
spi: pxa2xx: Allow number of chip select pins to be read from property
spi: dt-bindings: ti,qspi: convert to dtschema
spi: bitbang: Add missing MODULE_DESCRIPTION()
spi: bitbang: Use NSEC_PER_*SEC rather than hard coding
spi: dw: Drop default number of CS setting
spi: dw: Convert dw_spi::num_cs to u32
spi: dw: Add a number of native CS auto-detection
spi: dw: Convert to using BITS_TO_BYTES() macro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly cpufreq updates, including a significant intel-pstate
driver update and several amd-pstate improvements plus some updates of
ARM cpufreq drivers, general fixes and cleanups.
Also included are changes related to system sleep, power capping
updates adding support for a new platform and a new hardware feature
(among other things), a Samsung exynos-asv driver update allowing it
to change its Energy Model after adjusting voltage, minor cpuidle and
devfreq updates and a small documentation cleanup.
Specifics:
- Rework the handling of disabled turbo in the intel_pstate driver
and make it update the maximum CPU frequency consistently
regardless of the reason on top of a number of cleanups (Rafael
Wysocki)
- Add missing checks for NULL .exit() cpufreq driver callback to the
cpufreq core (Viresh Kumar)
- Prevent pulicy->max from going above the frequency QoS maximum
value when cpufreq_frequency_table_verify() is used (Xuewen Yan)
- Prevent a negative CPU number or frequency value from being printed
if they are really large (Joshua Yeong)
- Update MAINTAINERS entry for amd-pstate to add two new
submaintainers and a designated reviewer (Huang Rui)
- Clean up the amd-pstate driver and update its documentation
(Gautham Shenoy)
- Fix the highest frequency issue in the amd-pstate driver which
limits performance (Perry Yuan)
- Enable CPPC v2 for certain processors in the family 17H, as
requested by TR40 processor users who expect improved performance
and lower system temperature (Perry Yuan)
- Change latency and delay values to be read from platform firmware
firstly for more accurate timing (Perry Yuan)
- A new quirk is introduced for supporting amd-pstate on legacy
processors which either lack CPPC capability, or only only have
CPPC v2 capability (Perry Yuan)
- Sun50i cpufreq: Add support for opp_supported_hw, H616 platform and
general cleanups (Andre Przywara, Martin Botka, Brandon Cheo Fusi,
Dan Carpenter, Viresh Kumar)
- CPPC cpufreq: Fix possible null pointer dereference (Aleksandr
Mishin)
- Eliminate uses of of_node_put() from cpufreq (Javier Carrasco,
Shivani Gupta)
- brcmstb-avs: ISO C90 forbids mixed declarations (Portia Stephens)
- mediatek cpufreq: Add support for MT7988A (Sam Shih)
- cpufreq-qcom-hw: Add SM4450 compatibles in DT bindings (Tengfei
Fan)
- Fix struct cpudata::epp_cached kernel-doc in the intel_pstate
cpufreq driver (Jeff Johnson)
- Fix kerneldoc description of ladder_do_selection() (Jeff Johnson)
- Convert the cpuidle kirkwood driver to platform remove callback
returning void (Yangtao Li)
- Replace deprecated strncpy() with strscpy() in the hibernation core
code (Justin Stitt)
- Use %ps to simplify debug output in the core system-wide suspend
and resume code (Len Brown)
- Remove unnecessary else from device_init_wakeup() and make
device_wakeup_disable() return void (Dhruva Gole)
- Enable PMU support in the Intel TPMI RAPL driver (Zhang Rui)
- Add support for ArrowLake-H platform to the Intel RAPL driver
(Zhang Rui)
- Avoid explicit cpumask allocation on stack in DTPM (Dawei Li)
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba)
- Remove a reference to a function that has been dropped from the
power management documentation (Bjorn Helgaas)
- Convert the platfrom remove callback to .remove_new for the
exyno-nocp, exynos-ppmu, mtk-cci-devfreq, sun8i-a33-mbus, and
rk3399_dmc devfreq drivers (Uwe Kleine-König)
- Use DEFINE_SIMPLE_PM_OPS for exyno-bus.c driver (Anand Moon)"
* tag 'pm-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (68 commits)
PM / devfreq: exynos: Use DEFINE_SIMPLE_DEV_PM_OPS for PM functions
PM / devfreq: rk3399_dmc: Convert to platform remove callback returning void
PM / devfreq: sun8i-a33-mbus: Convert to platform remove callback returning void
PM / devfreq: mtk-cci: Convert to platform remove callback returning void
PM / devfreq: exynos-ppmu: Convert to platform remove callback returning void
PM / devfreq: exynos-nocp: Convert to platform remove callback returning void
cpufreq: amd-pstate: fix the highest frequency issue which limits performance
cpufreq: intel_pstate: fix struct cpudata::epp_cached kernel-doc
cpuidle: ladder: fix ladder_do_selection() kernel-doc
powercap: intel_rapl_tpmi: Enable PMU support
powercap: intel_rapl: Introduce APIs for PMU support
PM: hibernate: replace deprecated strncpy() with strscpy()
cpufreq: Fix up printing large CPU numbers and frequency values
MAINTAINERS: cpufreq: amd-pstate: Add co-maintainers and reviewer
cpufreq: amd-pstate: remove unused variable lowest_nonlinear_freq
cpufreq: amd-pstate: fix code format problems
cpufreq: amd-pstate: Add quirk for the pstate CPPC capabilities missing
cppc_acpi: print error message if CPPC is unsupported
cpufreq: amd-pstate: get transition delay and latency value from ACPI tables
cpufreq: amd-pstate: Bail out if min/max/nominal_freq is 0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The most interesting parts are probably the mm changes from Ryan which
optimise the creation of the linear mapping at boot and (separately)
implement write-protect support for userfaultfd.
Outside of our usual directories, the Kbuild-related changes under
scripts/ have been acked by Masahiro whilst the drivers/acpi/ parts
have been acked by Rafael and the addition of cpumask_any_and_but()
has been acked by Yury.
ACPI:
- Support for the Firmware ACPI Control Structure (FACS) signature
feature which is used to reboot out of hibernation on some systems
Kbuild:
- Support for building Flat Image Tree (FIT) images, where the kernel
Image is compressed alongside a set of devicetree blobs
Memory management:
- Optimisation of our early page-table manipulation for creation of
the linear mapping
- Support for userfaultfd write protection, which brings along some
nice cleanups to our handling of invalid but present ptes
- Extend our use of range TLBI invalidation at EL1
Perf and PMUs:
- Ensure that the 'pmu->parent' pointer is correctly initialised by
PMU drivers
- Avoid allocating 'cpumask_t' types on the stack in some PMU drivers
- Fix parsing of the CPU PMU "version" field in assembly code, as it
doesn't follow the usual architectural rules
- Add best-effort unwinding support for USER_STACKTRACE
- Minor driver fixes and cleanups
Selftests:
- Minor cleanups to the arm64 selftests (missing NULL check, unused
variable)
Miscellaneous:
- Add a command-line alias for disabling 32-bit application support
- Add part number for Neoverse-V2 CPUs
- Minor fixes and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (64 commits)
arm64/mm: Fix pud_user_accessible_page() for PGTABLE_LEVELS <= 2
arm64/mm: Add uffd write-protect support
arm64/mm: Move PTE_PRESENT_INVALID to overlay PTE_NG
arm64/mm: Remove PTE_PROT_NONE bit
arm64/mm: generalize PMD_PRESENT_INVALID for all levels
arm64: simplify arch_static_branch/_jump function
arm64: Add USER_STACKTRACE support
arm64: Add the arm64.no32bit_el0 command line option
drivers/perf: hisi: hns3: Actually use devm_add_action_or_reset()
drivers/perf: hisi: hns3: Fix out-of-bound access when valid event group
drivers/perf: hisi_pcie: Fix out-of-bound access when valid event group
kselftest: arm64: Add a null pointer check
arm64: defer clearing DAIF.D
arm64: assembler: update stale comment for disable_step_tsk
arm64/sysreg: Update PIE permission encodings
kselftest/arm64: Remove unused parameters in abi test
perf/arm-spe: Assign parents for event_source device
perf/arm-smmuv3: Assign parents for event_source device
perf/arm-dsu: Assign parents for event_source device
perf/arm-dmc620: Assign parents for event_source device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Core code:
- Interrupt storm detection for the lockup watchdog:
Lockups which are caused by interrupt storms are not easy to debug
because there is no information about the events which make the
lockup detector trigger.
To make this more user friendly, provide an extenstion to interrupt
statistics which allows to take snapshots and an interface to
retrieve the delta to the snapshot. Use this new mechanism in the
watchdog code to do a two stage lockup analysis by taking the
snapshot and printing the deltas for the topmost active interrupts
on the second trigger.
Note: This contains both the interrupt and the watchdog changes as
the latter depend on the former obviously.
- Avoid summation loops in the /proc/interrupts output and use the
global counter when possible
- Skip suspended interrupts on CPU hotplug operations to ensure that
they are not delivered before the system resumes the device drivers
when coming out of suspend.
- On CPU hot-unplug interrupts which are affine to the outgoing CPU
are migrated to a different CPU in the affinity mask. This can fail
when the CPUs have no vectors left. Instead of giving up try to
migrate it to any online CPU and thereby breaking the affinity
setting in order to prevent a stale device interrupt which targets
an offline CPU
- The usual small cleanups
Driver code:
- Support for the RISCV AIA MSI controller
- Make the interrupt allocation for the Loongson PCH controller more
flexible to prevent vector exhaustion
- The usual set of cleanups and fixes all over the place"
* tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
cpuidle: Avoid explicit cpumask allocation on stack
irqchip/sifive-plic: Avoid explicit cpumask allocation on stack
irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack
irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack
irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack
irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack
cpumask: Introduce cpumask_first_and_and()
irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown
genirq: Reuse irq_is_nmi()
genirq/cpuhotplug: Retry with cpu_online_mask when migration fails
genirq/cpuhotplug: Skip suspended interrupts when restoring affinity
arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251
arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251
ARM: dts: stm32: List exti parent interrupts on stm32mp131
ARM: dts: stm32: List exti parent interrupts on stm32mp151
arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32
irqchip/stm32-exti: Mark events reserved with RIF configuration check
irqchip/stm32-exti: Skip secure events
irqchip/stm32-exti: Convert driver to standard PM
...
|
