| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's a little bit of everything in here: we've got various
improvements and cleanups to drivers, some fixes across the board and
a bit of new hardware support"
* tag 'pwm/for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (22 commits)
dt-bindings: pwm: convert pwm-bcm2835 bindings to YAML
pwm: Add Renesas RZ/G2L MTU3a PWM driver
pwm: mtk_disp: Fix the disable flow of disp_pwm
dt-bindings: pwm: restrict node name suffixes
pwm: pca9685: Switch i2c driver back to use .probe()
pwm: ab8500: Fix error code in probe()
MAINTAINERS: add pwm to PolarFire SoC entry
pwm: add microchip soft ip corePWM driver
pwm: sysfs: Do not apply state to already disabled PWMs
pwm: imx-tpm: force 'real_period' to be zero in suspend
pwm: meson: make full use of common clock framework
pwm: meson: don't use hdmi/video clock as mux parent
pwm: meson: switch to using struct clk_parent_data for mux parents
pwm: meson: remove not needed check in meson_pwm_calc
pwm: meson: fix handling of period/duty if greater than UINT_MAX
pwm: meson: modify and simplify calculation in meson_pwm_get_state
dt-bindings: pwm: Add R-Car V3U device tree bindings
dt-bindings: pwm: imx: add i.MX8QXP compatible
pwm: mediatek: Add support for MT7981
dt-bindings: pwm: mediatek: Add mediatek,mt7981 compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Add new Qualcomm PMI8998/PM660 SMB2 charger
- bq256xx: support systems without thermistors
- cros_pchg: fix peripheral device status after system resume
- axp20x_usb_power: add support for AXP192
- qcom-pon: add support for pm8941
- at91-reset: prepare to expose reset reason to sysfs
- switch all I2C drivers back to use .probe instead of .probe_new
- convert some more DT bindings to YAML
- misc cleanups
* tag 'for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
MAINTAINERS: add documentation file for Microchip SAMA5D2 shutdown controller
dt-bindings: power: reset: atmel,sama5d2-shdwc: convert to yaml
dt-bindings: power: reset: atmel,at91sam9260-shdwc: convert to yaml
power: reset: at91-reset: change the power on reason prototype
power: reset: qcom-pon: add support for pm8941-pon
dt-bindings: power: reset: qcom-pon: define pm8941-pon
power: supply: add Qualcomm PMI8998 SMB2 Charger driver
dt-bindings: power: supply: qcom,pmi8998-charger: add bindings for smb2 driver
power: supply: rt9467: Make charger-enable control as logic level
power: supply: Switch i2c drivers back to use .probe()
power: reset: add HAS_IOPORT dependencies
dt-bindings: power: supply: axp20x: Add AXP192 compatible
power: supply: axp20x_usb_power: Add support for AXP192
power: supply: axp20x_usb_power: Remove variant IDs from VBUS polling check
power: supply: axp20x_usb_power: Use regmap field for VBUS disabling
power: supply: axp20x_usb_power: Use regmap fields for USB BC feature
power: supply: axp20x_usb_power: Use regmap fields for VBUS monitor feature
power: supply: axp20x_usb_power: Simplify USB current limit handling
power: supply: hwmon: constify pointers to hwmon_channel_info
power: supply: twl4030_madc_battery: Refactor twl4030_madc_bat_ext_changed()
...
|
|
Pull virtio updates from Michael Tsirkin:
- resume support in vdpa/solidrun
- structure size optimizations in virtio_pci
- new pds_vdpa driver
- immediate initialization mechanism for vdpa/ifcvf
- interrupt bypass for vdpa/mlx5
- multiple worker support for vhost
- viirtio net in Intel F2000X-PL support for vdpa/ifcvf
- fixes, cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
vhost: Make parameter name match of vhost_get_vq_desc()
vduse: fix NULL pointer dereference
vhost: Allow worker switching while work is queueing
vhost_scsi: add support for worker ioctls
vhost: allow userspace to create workers
vhost: replace single worker pointer with xarray
vhost: add helper to parse userspace vring state/file
vhost: remove vhost_work_queue
vhost_scsi: flush IO vqs then send TMF rsp
vhost_scsi: convert to vhost_vq_work_queue
vhost_scsi: make SCSI cmd completion per vq
vhost_sock: convert to vhost_vq_work_queue
vhost: convert poll work to be vq based
vhost: take worker or vq for flushing
vhost: take worker or vq instead of dev for queueing
vhost, vhost_net: add helper to check if vq has work
vhost: add vhost_worker pointer to vhost_virtqueue
vhost: dynamically allocate vhost_worker
vhost: create worker at end of vhost_dev_set_owner
virtio_bt: call scheduler when we free unused buffs
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM64:
- Eager page splitting optimization for dirty logging, optionally
allowing for a VM to avoid the cost of hugepage splitting in the
stage-2 fault path.
- Arm FF-A proxy for pKVM, allowing a pKVM host to safely interact
with services that live in the Secure world. pKVM intervenes on
FF-A calls to guarantee the host doesn't misuse memory donated to
the hyp or a pKVM guest.
- Support for running the split hypervisor with VHE enabled, known as
'hVHE' mode. This is extremely useful for testing the split
hypervisor on VHE-only systems, and paves the way for new use cases
that depend on having two TTBRs available at EL2.
- Generalized framework for configurable ID registers from userspace.
KVM/arm64 currently prevents arbitrary CPU feature set
configuration from userspace, but the intent is to relax this
limitation and allow userspace to select a feature set consistent
with the CPU.
- Enable the use of Branch Target Identification (FEAT_BTI) in the
hypervisor.
- Use a separate set of pointer authentication keys for the
hypervisor when running in protected mode, as the host is untrusted
at runtime.
- Ensure timer IRQs are consistently released in the init failure
paths.
- Avoid trapping CTR_EL0 on systems with Enhanced Virtualization
Traps (FEAT_EVT), as it is a register commonly read from userspace.
- Erratum workaround for the upcoming AmpereOne part, which has
broken hardware A/D state management.
RISC-V:
- Redirect AMO load/store misaligned traps to KVM guest
- Trap-n-emulate AIA in-kernel irqchip for KVM guest
- Svnapot support for KVM Guest
s390:
- New uvdevice secret API
- CMM selftest and fixes
- fix racy access to target CPU for diag 9c
x86:
- Fix missing/incorrect #GP checks on ENCLS
- Use standard mmu_notifier hooks for handling APIC access page
- Drop now unnecessary TR/TSS load after VM-Exit on AMD
- Print more descriptive information about the status of SEV and
SEV-ES during module load
- Add a test for splitting and reconstituting hugepages during and
after dirty logging
- Add support for CPU pinning in demand paging test
- Add support for AMD PerfMonV2, with a variety of cleanups and minor
fixes included along the way
- Add a "nx_huge_pages=never" option to effectively avoid creating NX
hugepage recovery threads (because nx_huge_pages=off can be toggled
at runtime)
- Move handling of PAT out of MTRR code and dedup SVM+VMX code
- Fix output of PIC poll command emulation when there's an interrupt
- Add a maintainer's handbook to document KVM x86 processes,
preferred coding style, testing expectations, etc.
- Misc cleanups, fixes and comments
Generic:
- Miscellaneous bugfixes and cleanups
Selftests:
- Generate dependency files so that partial rebuilds work as
expected"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (153 commits)
Documentation/process: Add a maintainer handbook for KVM x86
Documentation/process: Add a label for the tip tree handbook's coding style
KVM: arm64: Fix misuse of KVM_ARM_VCPU_POWER_OFF bit index
RISC-V: KVM: Remove unneeded semicolon
RISC-V: KVM: Allow Svnapot extension for Guest/VM
riscv: kvm: define vcpu_sbi_ext_pmu in header
RISC-V: KVM: Expose IMSIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel virtualization of AIA IMSIC
RISC-V: KVM: Expose APLIC registers as attributes of AIA irqchip
RISC-V: KVM: Add in-kernel emulation of AIA APLIC
RISC-V: KVM: Implement device interface for AIA irqchip
RISC-V: KVM: Skeletal in-kernel AIA irqchip support
RISC-V: KVM: Set kvm_riscv_aia_nr_hgei to zero
RISC-V: KVM: Add APLIC related defines
RISC-V: KVM: Add IMSIC related defines
RISC-V: KVM: Implement guest external interrupt line management
KVM: x86: Remove PRIx* definitions as they are solely for user space
s390/uv: Update query for secret-UVCs
s390/uv: replace scnprintf with sysfs_emit
s390/uvdevice: Add 'Lock Secret Store' UVC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Skip empty folders creation
sysfs: Improve readability by following the kernel coding style
drivers: fwnode: fix fwnode_irq_get[_byname]()
ata: ahci_platform: Make code agnostic to OF/ACPI
device property: Implement device_is_compatible()
ACPI: Move ACPI_DEVICE_CLASS() to mod_devicetable.h
base/node: Use 'property' to identify an access parameter
driver core: device.h: add some missing kerneldocs
kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
isa: Remove unnecessary checks
MAINTAINERS: add entry for auxiliary bus
debugfs: Correct the 'debugfs_create_str' docs
serial: qcom_geni: Comment use of devm_krealloc rather than devm_krealloc_array
iio: adc: Use devm_krealloc_array
hwmon: pmbus: Use devm_krealloc_array
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates on top of that, lots of
small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (243 commits)
bsr: fix build problem with bsr_class static cleanup
comedi: make all 'class' structures const
char: xillybus: make xillybus_class a static const structure
xilinx_hwicap: make icap_class a static const structure
virtio_console: make port class a static const structure
ppdev: make ppdev_class a static const structure
char: misc: make misc_class a static const structure
/dev/mem: make mem_class a static const structure
char: lp: make lp_class a static const structure
dsp56k: make dsp56k_class a static const structure
bsr: make bsr_class a static const structure
oradax: make 'cl' a static const structure
hwtracing: hisi_ptt: Fix potential sleep in atomic context
hwtracing: hisi_ptt: Advertise PERF_PMU_CAP_NO_EXCLUDE for PTT PMU
hwtracing: hisi_ptt: Export available filters through sysfs
hwtracing: hisi_ptt: Add support for dynamically updating the filter list
hwtracing: hisi_ptt: Factor out filter allocation and release operation
samples: pfsm: add CC_CAN_LINK dependency
misc: fastrpc: check return value of devm_kasprintf()
coresight: dummy: Update type of mode parameter in dummy_{sink,source}_enable()
...
|
|
Pull iomap updates from Darrick Wong:
- Fix a type signature mismatch
- Drop Christoph as maintainer
* tag 'iomap-6.5-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: drop me [hch] from MAINTAINERS for iomap
fs: iomap: Change the type of blocksize from 'int' to 'unsigned int' in iomap_file_buffered_write_punch_delalloc
|
|
Pull CXL updates from Dan Williams:
"The highlights in terms of new functionality are support for the
standard CXL Performance Monitor definition that appeared in CXL 3.0,
support for device sanitization (wiping all data from a device),
secure-erase (re-keying encryption of user data), and support for
firmware update. The firmware update support is notable as it reuses
the simple sysfs_upload interface to just cat(1) a blob to a sysfs
file and pipe that to the device.
Additionally there are a substantial number of cleanups and
reorganizations to get ready for RCH error handling (RCH == Restricted
CXL Host == current shipping hardware generation / pre CXL-2.0
topologies) and type-2 (accelerator / vendor specific) devices.
For vendor specific devices they implement a subset of what the
generic type-3 (generic memory expander) driver expects. As a result
the rework decouples optional infrastructure from the core driver
context.
For RCH topologies, where the specification working group did not want
to confuse pre-CXL-aware operating systems, many of the standard
registers are hidden which makes support standard bus features like
AER (PCIe Advanced Error Reporting) difficult. The rework arranges for
the driver to help the PCI-AER core. Bjorn is on board with this
direction but a late regression disocvery means the completion of this
functionality needs to cook a bit longer, so it is code
reorganizations only for now.
Summary:
- Add infrastructure for supporting background commands along with
support for device sanitization and firmware update
- Introduce a CXL performance monitoring unit driver based on the
common definition in the specification.
- Land some preparatory cleanup and refactoring for the anticipated
arrival of CXL type-2 (accelerator devices) and CXL RCH (CXL-v1.1
topology) error handling.
- Rework CPU cache management with respect to region configuration
(device hotplug or other dynamic changes to memory interleaving)
- Fix region reconfiguration vs CXL decoder ordering rules"
* tag 'cxl-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (51 commits)
cxl: Fix one kernel-doc comment
cxl/pci: Use correct flag for sanitize polling
docs: perf: Minimal introduction the the CXL PMU device and driver
perf: CXL Performance Monitoring Unit driver
tools/testing/cxl: add firmware update emulation to CXL memdevs
tools/testing/cxl: Use named effects for the Command Effect Log
tools/testing/cxl: Fix command effects for inject/clear poison
cxl: add a firmware update mechanism using the sysfs firmware loader
cxl/test: Add Secure Erase opcode support
cxl/mem: Support Secure Erase
cxl/test: Add Sanitize opcode support
cxl/mem: Wire up Sanitization support
cxl/mbox: Add sanitization handling machinery
cxl/mem: Introduce security state sysfs file
cxl/mbox: Allow for IRQ_NONE case in the isr
Revert "cxl/port: Enable the HDM decoder capability for switch ports"
cxl/memdev: Formalize endpoint port linkage
cxl/pci: Unconditionally unmask 256B Flit errors
cxl/region: Manage decoder target_type at decoder-attach time
cxl/hdm: Default CXL_DEVTYPE_DEVMEM decoders to CXL_DECODER_DEVMEM
...
|
|
KVM x86 changes for 6.5:
* Move handling of PAT out of MTRR code and dedup SVM+VMX code
* Fix output of PIC poll command emulation when there's an interrupt
* Add a maintainer's handbook to document KVM x86 processes, preferred coding
style, testing expectations, etc.
* Misc cleanups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add linear akcipher/sig API
- Add tfm cloning (hmac, cmac)
- Add statesize to crypto_ahash
Algorithms:
- Allow only odd e and restrict value in FIPS mode for RSA
- Replace LFSR with SHA3-256 in jitter
- Add interface for gathering of raw entropy in jitter
Drivers:
- Fix race on data_avail and actual data in hwrng/virtio
- Add hash and HMAC support in starfive
- Add RSA algo support in starfive
- Add support for PCI device 0x156E in ccp"
* tag 'v6.5-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (85 commits)
crypto: akcipher - Do not copy dst if it is NULL
crypto: sig - Fix verify call
crypto: akcipher - Set request tfm on sync path
crypto: sm2 - Provide sm2_compute_z_digest when sm2 is disabled
hwrng: imx-rngc - switch to DEFINE_SIMPLE_DEV_PM_OPS
hwrng: st - keep clock enabled while hwrng is registered
hwrng: st - support compile-testing
hwrng: imx-rngc - fix the timeout for init and self check
KEYS: asymmetric: Use new crypto interface without scatterlists
KEYS: asymmetric: Move sm2 code into x509_public_key
KEYS: Add forward declaration in asymmetric-parser.h
crypto: sig - Add interface for sign/verify
crypto: akcipher - Add sync interface without SG lists
crypto: cipher - On clone do crypto_mod_get()
crypto: api - Add __crypto_alloc_tfmgfp
crypto: api - Remove crypto_init_ops()
crypto: rsa - allow only odd e and restrict value in FIPS mode
crypto: geniv - Split geniv out of AEAD Kconfig option
crypto: algboss - Add missing dependency on RNG2
crypto: starfive - Add RSA algo support
...
|
|
Pull VFIO updates from Alex Williamson:
- Adjust log levels for common messages (Oleksandr Natalenko, Alex
Williamson)
- Support for dynamic MSI-X allocation (Reinette Chatre)
- Enable and report PCIe AtomicOp Completer capabilities (Alex
Williamson)
- Cleanup Kconfigs for vfio bus drivers (Alex Williamson)
- Add support for CDX bus based devices (Nipun Gupta)
- Fix race with concurrent mdev initialization (Eric Farman)
* tag 'vfio-v6.5-rc1' of https://github.com/awilliam/linux-vfio:
vfio/mdev: Move the compat_class initialization to module init
vfio/cdx: add support for CDX bus
vfio/fsl: Create Kconfig sub-menu
vfio/platform: Cleanup Kconfig
vfio/pci: Cleanup Kconfig
vfio/pci-core: Add capability for AtomicOp completer support
vfio/pci: Also demote hiding standard cap messages
vfio/pci: Clear VFIO_IRQ_INFO_NORESIZE for MSI-X
vfio/pci: Support dynamic MSI-X
vfio/pci: Probe and store ability to support dynamic MSI-X
vfio/pci: Use bitfield for struct vfio_pci_core_device flags
vfio/pci: Update stale comment
vfio/pci: Remove interrupt context counter
vfio/pci: Use xarray for interrupt context storage
vfio/pci: Move to single error path
vfio/pci: Prepare for dynamic interrupt context storage
vfio/pci: Remove negative check on unsigned vector
vfio/pci: Consolidate irq cleanup on MSI/MSI-X disable
vfio/pci: demote hiding ecap messages to debug level
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Export pcie_retrain_link() for use outside ASPM
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up
- Work around link training failures (especially on the ASMedia
ASM2824 switch) by training first at 2.5GT/s and then attempting
higher rates
Resource management:
- When we coalesce host bridge windows, remove invalidated resources
from the resource tree so future allocations work correctly
Hotplug:
- Cancel bringup sequence if card is not present, to keep from
blinking Power Indicator indefinitely
- Reassign bridge resources if necessary for ACPI hotplug
Driver binding:
- Convert platform_device .remove() callbacks to return void instead
of a mostly useless int
Power management:
- Reduce wait time for secondary bus to be ready to speed up resume
- Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in
D3cold
- Call _REG when transitioning D-states so AML that uses the PCI
config space OpRegion works, which fixes some ASMedia GPIO
controllers after resume
Virtualization:
- Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM
hang when guest is rebooted
- Add function 1 DMA alias quirk for Marvell 88SE9235
Error handling:
- Unexport pci_save_aer_state() since it's only used in drivers/pci/
- Drop recommendation for drivers to configure AER Capability, since
the PCI core does this for all devices
ASPM:
- Disable ASPM on MFD function removal to avoid use-after-free
- Tighten up pci_enable_link_state() and pci_disable_link_state()
interfaces so they don't enable/disable states the driver didn't
specify
- Avoid link retraining race that can happen if ASPM sets link
control parameters while the link is in the midst of training for
some other reason
Endpoint framework:
- Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be
different from "PCI Endpoint NTB driver"
- Automatically create a function specific attributes group for
endpoint drivers to avoid reference counting issues
- Fix many EPC test issues
- Return pci_epf_type_add_cfs() error if EPF has no driver
- Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq()
MSI vector parameters
- Pass EPF device ID to driver probe functions
- Return -EALREADY if EPC has already been started/stopped
- Add linkdown notifier support and use it in qcom-ep
- Add Bus Master Enable event support and use it in qcom-ep
- Add Qualcomm Modem Host Interface (MHI) endpoint driver
- Add Layerscape PME interrupt handling to manage link-up
notification
Cadence PCIe controller driver:
- Wait for link retrain to complete when working around the J721E
i2085 erratum with Gen2 mode
Faraday FTPC100 PCI controller driver:
- Release clock resources on error paths
Freescale i.MX6 PCIe controller driver:
- Save and restore Root Port MSI control to work around hardware defect
Intel VMD host bridge driver:
- Reset VMD config register between soft reboots
- Capture pci_reset_bus() return value instead of printing junk when
it fails
Qualcomm PCIe controller driver:
- Add SDX65 endpoint compatible string to DT binding
- Disable register write access after init for IP v2.3.3, v2.9.0
- Use DWC helpers for enabling/disabling writes to DBI registers
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0
- Reuse v2.3.2 post-init sequence for v2.4.0
Renesas R-Car PCIe controller driver:
- Remove unused static pcie_base and pcie_dev
Rockchip PCIe controller driver:
- Remove writes to unused registers
- Write endpoint Device ID using correct register
- Assert PCI Configuration Enable bit after probe so endpoint
responds instead of generating Request Retry Status messages
- Poll waiting for PHY PLLs to lock
- Update RK3399 example DT binding to be valid
- Use RK3399 PCIE_CLIENT_LEGACY_INT_CTRL to generate INTx instead of
manually generating PCIe message
- Use multiple windows to avoid address translation conflicts
- Use u32 (not u16) when accessing 32-bit registers
- Hide MSI-X Capability, since RK3399 can't generate MSI-X
- Set endpoint controller required alignment to 256
Synopsys DesignWare PCIe controller driver:
- Wait for link to come up only if we've initiated link training
Miscellaneous:
- Add pci_clear_master() stub for non-CONFIG_PCI"
* tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
Documentation: PCI: correct spelling
PCI: vmd: Fix uninitialized variable usage in vmd_enable_domain()
PCI: xgene-msi: Convert to platform remove callback returning void
PCI: tegra: Convert to platform remove callback returning void
PCI: rockchip-host: Convert to platform remove callback returning void
PCI: mvebu: Convert to platform remove callback returning void
PCI: mt7621: Convert to platform remove callback returning void
PCI: mediatek-gen3: Convert to platform remove callback returning void
PCI: mediatek: Convert to platform remove callback returning void
PCI: iproc: Convert to platform remove callback returning void
PCI: hisi-error: Convert to platform remove callback returning void
PCI: dwc: Convert to platform remove callback returning void
PCI: j721e: Convert to platform remove callback returning void
PCI: brcmstb: Convert to platform remove callback returning void
PCI: altera-msi: Convert to platform remove callback returning void
PCI: altera: Convert to platform remove callback returning void
PCI: aardvark: Convert to platform remove callback returning void
PCI: rcar: Use correct product family name for Renesas R-Car
PCI: layerscape: Add the endpoint linkup notifier support
PCI: endpoint: pci-epf-vntb: Fix typo in comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time
New drivers:
- Tegra234 support
- Qualcomm IPQ5018 support
- Intel Meteor Lake-S support
- Qualcomm SDX75 subdriver
- Qualcomm SPMI-based PM8953 support
Improvements:
- Fix up support for GPIO3 on the AXP209
- Push-pull drive configuration support for the AT91 PIO4
- Fix misc non-urgent bugs in the AMD driver
- Misc non-urgent improved error handling
- Misc janitorial and minor improvements"
* tag 'pinctrl-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: cherryview: Drop goto label
pinctrl: baytrail: invert if condition
pinctrl: baytrail: add warning for BYT_VAL_REG retrieval failure
pinctrl: baytrail: reduce scope of spinlock in ->dbg_show() hook
pinctrl: tegra: avoid duplicate field initializers
dt-bindings: pinctrl: qcom,sdx65-tlmm: add pcie_clkreq function
pinctrl: mlxbf3: remove broken Kconfig 'select'
pinctrl: spear: Remove unused of_gpio.h inclusion
pinctrl: lantiq: Remove unused of_gpio.h inclusion
pinctrl: at91-pio4: check return value of devm_kasprintf()
pinctrl: microchip-sgpio: check return value of devm_kasprintf()
pinctrl: freescale: Fix a memory out of bounds when num_configs is 1
pinctrl: intel: refine ->irq_set_type() hook
pinctrl: intel: refine ->set_mux() hook
pinctrl: baytrail: Use str_hi_lo() helper
lib/string_choices: Add str_high_low() helper
lib/string_helpers: Split out string_choices.h
lib/string_helpers: Add missing header files to MAINTAINERS database
pinctrl: npcm7xx: Add missing check for ioremap
pinctrl:sunplus: Add check for kmalloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"AMD PMC and PMF drivers:
- Various bugfixes
- Improved debugging support
Intel PMC:
- Refactor to support hw with multiple PMCs
- Various other improvements / new hw support
Intel Speed Select Technology (ISST):
- TPMI Uncore Frequency + Cluster Level Power Controls
- Various bugfixes
- tools/intel-speed-select: Misc improvements
Dell-DDV: Add documentation
INT3472 ACPI camera sensor glue code:
- Evaluate device's _DSM method to control imaging clock
- Drop the need to have a table with per sensor-model info
Lenovo Yogabook:
- Refactor / rework to also support Android models
Think-LMI:
- Multiple improvements and fixes
WMI:
- Add proper API documentation for the WMI bus
x86-android-tablets:
- Misc new hw support
Miscellaneous other cleanups / fixes"
* tag 'platform-drivers-x86-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (91 commits)
platform/x86:intel/pmc: Add Meteor Lake IOE-M PMC related maps
platform/x86:intel/pmc: Add Meteor Lake IOE-P PMC related maps
platform/x86:intel/pmc: Use SSRAM to discover pwrm base address of primary PMC
platform/x86:intel/pmc: Discover PMC devices
platform/x86:intel/pmc: Enable debugfs multiple PMC support
platform/x86:intel/pmc: Add support to handle multiple PMCs
platform/x86:intel/pmc: Combine core_init() and core_configure()
platform/x86:intel/pmc: Update maps for Meteor Lake P/M platforms
platform/x86/intel: tpmi: Remove hardcoded unit and offset
platform/x86: int3472: discrete: Log a warning if the pin-numbers don't match
platform/x86: int3472: discrete: Use FIELD_GET() on the GPIO _DSM return value
platform/x86: int3472: discrete: Add alternative "AVDD" regulator supply name
platform/x86: int3472: discrete: Add support for 1 GPIO regulator shared between 2 sensors
platform/x86: int3472: discrete: Remove sensor_config-s
platform/x86: int3472: discrete: Drop GPIO remapping support
platform/x86: apple-gmux: don't use be32_to_cpu and cpu_to_be32
platform/x86/dell/dell-rbtn: Fix resources leaking on error path
platform/x86: ISST: Fix usage counter
platform/x86: ISST: Reset default callback on unregister
platform/x86: int3472: Switch back to use struct i2c_driver's .probe()
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, pm80xx, libata-scsi, smartpqi,
lpfc, qla2xxx).
We have a couple of major core changes impacting other systems:
- Command Duration Limits, which spills into block and ATA
- block level Persistent Reservation Operations, which touches block,
nvme, target and dm
Both of these are added with merge commits containing a cover letter
explaining what's going on"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (187 commits)
scsi: core: Improve warning message in scsi_device_block()
scsi: core: Replace scsi_target_block() with scsi_block_targets()
scsi: core: Don't wait for quiesce in scsi_device_block()
scsi: core: Don't wait for quiesce in scsi_stop_queue()
scsi: core: Merge scsi_internal_device_block() and device_block()
scsi: sg: Increase number of devices
scsi: bsg: Increase number of devices
scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
scsi: ufs: ufs-pci: Add support for Intel Arrow Lake
scsi: sd: sd_zbc: Use PAGE_SECTORS_SHIFT
scsi: ufs: wb: Add explicit flush_threshold sysfs attribute
scsi: ufs: ufs-qcom: Switch to the new ICE API
scsi: ufs: dt-bindings: qcom: Add ICE phandle
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_RTC quirk
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_INTR quirk
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_RTC
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_INTR
scsi: ufs: core: Remove dedicated hwq for dev command
scsi: ufs: core: mcq: Fix the incorrect OCS value for the device command
scsi: ufs: dt-bindings: samsung,exynos: Drop unneeded quotes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for ACPI
- Various cleanups to the ISA string parsing, including making them
case-insensitive
- Support for the vector extension
- Support for independent irq/softirq stacks
- Our CPU DT binding now has "unevaluatedProperties: false"
* tag 'riscv-for-linus-6.5-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (78 commits)
riscv: hibernate: remove WARN_ON in save_processor_state
dt-bindings: riscv: cpus: switch to unevaluatedProperties: false
dt-bindings: riscv: cpus: add a ref the common cpu schema
riscv: stack: Add config of thread stack size
riscv: stack: Support HAVE_SOFTIRQ_ON_OWN_STACK
riscv: stack: Support HAVE_IRQ_EXIT_ON_IRQ_STACK
RISC-V: always report presence of extensions formerly part of the base ISA
dt-bindings: riscv: explicitly mention assumption of Zicntr & Zihpm support
RISC-V: remove decrement/increment dance in ISA string parser
RISC-V: rework comments in ISA string parser
RISC-V: validate riscv,isa at boot, not during ISA string parsing
RISC-V: split early & late of_node to hartid mapping
RISC-V: simplify register width check in ISA string parsing
perf: RISC-V: Limit the number of counters returned from SBI
riscv: replace deprecated scall with ecall
riscv: uprobes: Restore thread.bad_cause
riscv: mm: try VMA lock-based page fault handling first
riscv: mm: Pre-allocate PGD entries for vmalloc/modules area
RISC-V: hwprobe: Expose Zba, Zbb, and Zbs
RISC-V: Track ISA extensions per hart
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Extend KCSAN support to 32-bit and BookE. Add some KCSAN annotations
- Make ELFv2 ABI the default for 64-bit big-endian kernel builds, and
use the -mprofile-kernel option (kernel specific ftrace ABI) for big
endian ELFv2 kernels
- Add initial Dynamic Execution Control Register (DEXCR) support, and
allow the ROP protection instructions to be used on Power 10
- Various other small features and fixes
Thanks to Aditya Gupta, Aneesh Kumar K.V, Benjamin Gray, Brian King,
Christophe Leroy, Colin Ian King, Dmitry Torokhov, Gaurav Batra, Jean
Delvare, Joel Stanley, Marco Elver, Masahiro Yamada, Nageswara R Sastry,
Nathan Chancellor, Naveen N Rao, Nayna Jain, Nicholas Piggin, Paul
Gortmaker, Randy Dunlap, Rob Herring, Rohan McLure, Russell Currey,
Sachin Sant, Timothy Pearson, Tom Rix, and Uwe Kleine-König.
* tag 'powerpc-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (76 commits)
powerpc: remove checks for binutils older than 2.25
powerpc: Fail build if using recordmcount with binutils v2.37
powerpc/iommu: TCEs are incorrectly manipulated with DLPAR add/remove of memory
powerpc/iommu: Only build sPAPR access functions on pSeries
powerpc: powernv: Annotate data races in opal events
powerpc: Mark writes registering ipi to host cpu through kvm and polling
powerpc: Annotate accesses to ipi message flags
powerpc: powernv: Fix KCSAN datarace warnings on idle_state contention
powerpc: Mark [h]ssr_valid accesses in check_return_regs_valid
powerpc: qspinlock: Enforce qnode writes prior to publishing to queue
powerpc: qspinlock: Mark accesses to qnode lock checks
powerpc/powernv/pci: Remove last IODA1 defines
powerpc/powernv/pci: Remove MVE code
powerpc/powernv/pci: Remove ioda1 support
powerpc: 52xx: Make immr_id DT match tables static
powerpc: mpc512x: Remove open coded "ranges" parsing
powerpc: fsl_soc: Use of_range_to_resource() for "ranges" parsing
powerpc: fsl: Use of_property_read_reg() to parse "reg"
powerpc: fsl_rio: Use of_range_to_resource() for "ranges" parsing
macintosh: Use of_property_read_reg() to parse "reg"
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform to use GPIO
descriptors throughout the tree, for any devices that are not fully
converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212 chip
that was previously unused and removed but is now used for the Samsung
Galaxy Tab3"
* tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
ARM: omap2: Fix copy/paste bug
MAINTAINERS: Replace my email address
Input: ads7846 - fix pointer cast warning
Input: ads7846 - Fix usage of match data
ARM: omap2: Fix checkpatch issues
arm: omap1: replace printk() with pr_err macro
ARM: omap: Fix checkpatch issues
ARM: s3c: Switch i2c drivers back to use .probe()
ARM: versatile: mark mmc_status() static
ARM: spear: include "pl080.h" for pl080_get_signal() prototype
ARM: sa1100: address missing prototype warnings
ARM: pxa: fix missing-prototypes warnings
ARM: orion5x: fix d2net gpio initialization
ARM: omap2: fix missing tick_broadcast() prototype
ARM: omap1: add missing include
ARM: lpc32xx: add missing include
ARM: imx: add missing include
ARM: highbank: add missing include
ARM: ep93xx: fix missing-prototype warnings
ARM: davinci: fix davinci_cpufreq_init() declaration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are two new SoC families this time, and both appear fairly
similar: The Nuvoton MA35D1 and the STMicroelectronics STM32MP2 are
both dual-core Cortex-A35 based chips for the low-power industrial
embedded market, and they mark the first 64-bit product in a widely
used family of 32-bit Arm MCUs and SoCs.
The way into the kernel is completely different here: The team at ST
has a long history of working upstream with their STM32MP1 and other
SoCs, and they produced a complete port to arm64 together with the
initial announcement. Nuvoton also has multiple SoC product lines with
current or previous upstream support, but those are maintained by
third parties and are unrelated. The patch series from Nuvoton's Jacky
Huang had to go through many revisisions to get to this point and is
still missing a few drivers including the serial port for the moment.
The branch contains the devicetree files as well as all the code
changes, in order to have something that can be tested standalone"
* tag 'soc-newsoc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
clk: nuvoton: Use clk_parent_data instead of string for parent clock
clk: nuvoton: Update all constant hex values to lowercase
clk: nuvoton: Add clk-ma35d1.h for driver extern functions
remoteproc: stm32: use correct format strings on 64-bit
MAINTAINERS: add entry for ARM/STM32 ARCHITECTURE
arm64: defconfig: enable ARCH_STM32 and STM32 serial driver
arm64: dts: st: add stm32mp257f-ev1 board support
dt-bindings: stm32: document stm32mp257f-ev1 board
arm64: dts: st: introduce stm32mp25 pinctrl files
arm64: dts: st: introduce stm32mp25 SoCs family
arm64: introduce STM32 family on Armv8 architecture
dt-bindings: stm32: add st,stm32mp25-syscfg compatible for syscon
pinctrl: stm32: add stm32mp257 pinctrl support
dt-bindings: pinctrl: stm32: support for stm32mp257 and additional packages
Documentation/process: add soc maintainer handbook
reset: RESET_NUVOTON_MA35D1 should depend on ARCH_MA35
reset: Add Nuvoton ma35d1 reset driver support
clk: nuvoton: Add clock driver for ma35d1 clock controller
arm64: dts: nuvoton: Add initial ma35d1 device tree
dt-bindings: serial: Document ma35d1 uart controller
...
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
|
