| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These properties are common for all i2c subnodes. Allows to add i2c device
nodes (like an rtc for example) in other .dts files including
sam9x60.dtsi without requiring to repeat these properties for each i2c
device again and again.
Found on a custom board after adding this in .dts:
&flx5 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
i2c5: i2c@600 {
pinctrl-0 = <&pinctrl_flx5_default>;
status = "okay";
pcf8523: rtc@68 {
compatible = "nxp,pcf8523";
reg = <0x68>;
};
};
};
… which created a warning like this:
[…]:236.4-17: Warning (reg_format): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
[…]: Warning (pci_device_reg): Failed prerequisite 'reg_format'
[…]: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
[…]: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
[…]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #address-cells for I2C bus also defined at […]:228.16-238.4
[…]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7: Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect #size-cells for I2C bus also defined at […]:228.16-238.4
[…]: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
[…]: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
[…]: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
[…]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #address-cells value
[…]:234.19-237.5: Warning (avoid_default_addr_size): /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #size-cells value
[…]: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
[…]: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
This probably should have been done with commit 84f23f3284d5 ("ARM: dts:
at91: sam9x60: move flexcom definitions") already, where those
address-cells and size-cells properties were left in the board .dts
files instead of moving them to the dtsi.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240528153109.439407-1-ada@thorsis.com
[claudiu.beznea: adjusted commit message as the properties are not
required anymore]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
The main boot sequence for Microchip AT91 devices is one of the
following:
1/ ROM BOOT -> AT91Bootstrap -> U-Boot -> Linux Kernel
2/ ROM BOOT -> AT91Bootstrap -> Linux Kernel
For case 1/ U-Boot is the stage where the Ethernet MAC addresses are set.
For case 2/ where U-Boot is skipped the Ethernet MAC addresses need to
be configured in Linux. For this add EEPROMs and nvmem-layout to describe
EUI48 MAC address regions.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[andrei.simion@microchip.com: Add nvmem-layout to describe eui48 mac
region. Align compatible name with datasheet. Reword commit message.]
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
[claudiu.beznea: adjusted the new commit message]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/20240703084704.197697-3-andrei.simion@microchip.com
|
|
Negate the values reported for the accelerometer z-axis in order to
match Documentation/devicetree/bindings/iio/mount-matrix.txt.
Fixes: 14a213dcb004 ("ARM: dts: n900: use iio driver for accelerometer")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-By: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240722113137.3240847-1-absicsz@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
By default, the ENET_REF is configured at 125MHz on i.MX6SX, which works
well for boards that operate in RGMII mode.
The imx6sx-udoo-neo has a KSZ8091 Ethernet PHY that is connected via
RMII interface, so a 50MHz ENET_REF clock is expected.
Describe the IMX6SX_CLK_ENET_REF accordingly.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 04f08ef291d4 ("arm/arm64: dts: arm: Use generic clock and
regulator nodenames") renamed nodes and created 2 "clock-24000000" nodes
(at different paths).
The kernel can't handle these duplicate names even though they are at
different paths. Fix this by renaming one of the nodes to "clock-pclk".
This name is aligned with other Arm boards (those didn't have a known
frequency to use in the node name).
Fixes: 04f08ef291d4 ("arm/arm64: dts: arm: Use generic clock and regulator nodenames")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bit clock and frame clock are provided by the mcasp. Change the
simple card settings regarding the clock provider and the mclk-fs for
usage with typical 44.1 kHz and 48 kHz sample rates.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Link: https://lore.kernel.org/r/20240730092353.10209-2-d.haller@phytec.de
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
RTS pin seems to have inverted behavior on am335x, other than expected
with default "rs485-rts-active-high" (instead of low on idle, high on send,
it is the opposite). Transceiver datasheet also suggests a pulldown.
Add includes to pin definitions that are used.
Signed-off-by: Steffen Hemer <s.hemer@phytec.de>
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Link: https://lore.kernel.org/r/20240730092353.10209-1-d.haller@phytec.de
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Use cleaner (and non-deprecated) bindings syntax. See commit
bd912c991d2e ("dt-bindings: nvmem: layouts: add fixed-layout") for
details.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240523042750.26238-1-zajec5@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Prior to commit df16c1c51d81 ("net: phy: mdio_device: Reset device only
when necessary") MDIO reset deasserts were performed twice during boot.
Now that the second deassert is no longer performed, device probe
failures happen due to the change in timing with the following error
message:
SMSC LAN8710/LAN8720: probe of 4a101000.mdio:00 failed with error -5
Restore the original effective timing, which resolves the probe
failures.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20240531183817.2698445-1-colin.foster@in-advantage.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The serial console settings in the chosen node are device-specific,
not SoC-specific. Move the chosen node out of bcm21664.dtsi and into
the only DTS that uses it, bcm21664-garnet.dts.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240729-bcm21664-common-v2-1-ebc21a89bf63@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Use cleaner (and non-deprecated) bindings syntax. See commit
bd912c991d2e ("dt-bindings: nvmem: layouts: add fixed-layout") for
details.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240516084737.2789-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Due to inter-branch dependencies, it was necessary to add the rk3128
sfc controller with its hclk_sfc using the numeric clock id value
instead of the nicer constant from the binding.
Now that it's available, change over to this constant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240623215631.440399-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull ARM updates from Russell King:
- ftrace: don't assume stack frames are contiguous in memory
- remove unused mod_inwind_map structure
- spelling fixes
- allow use of LD dead code/data elimination
- fix callchain_trace() return value
- add support for stackleak gcc plugin
- correct some reset asm function prototypes for CFI
[ Missed the merge window because Russell forgot to push out ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux:
ARM: 9408/1: mm: CFI: Fix some erroneous reset prototypes
ARM: 9407/1: Add support for STACKLEAK gcc plugin
ARM: 9406/1: Fix callchain_trace() return value
ARM: 9404/1: arm32: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION
ARM: 9403/1: Alpine: Spelling s/initialiing/initializing/
ARM: 9402/1: Kconfig: Spelling s/Cortex A-/Cortex-A/
ARM: 9400/1: Remove unused struct 'mod_unwind_map'
|
|
Correct the clock-names in the AHCI SATA controller node to adhere to
the bindings.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240717094914.17931-2-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Remove the reg-names property in the sata-phy node as it is not present
in the bindings and is not required by the driver.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240715130854.53501-3-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add pstore node to allow for retrieving crash logs.
Signed-off-by: Bingwu Zhang <xtexchooser@duck.com>
Link: https://lore.kernel.org/r/20240715122201.345426-2-xtex@envs.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Pass dtbs_check for qcom,ipq4019-pinctrl.yaml.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711110545.31641-7-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Pass dtbs_check for qcom,ipq8064-pinctrl.yaml.
Also remove invalid "bias-none" property, which I have assumed to mean
"bias-disable".
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711110545.31641-6-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Pass dtbs_check for qcom,apq8064-pinctrl.yaml.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711110545.31641-5-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Remove duplicate handle to i2c pins in the device tree, as they are
already set in qcom-apq8064.dtsi.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711110545.31641-4-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The "drive-strength" property was incorrectly spelt as "drive-strengh".
Correct this.
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240711110545.31641-3-rayyan.ansari@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Wrap existing pwrkey node inside a pon node, to conform to dt schema.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
Link: https://lore.kernel.org/r/20240725-pmic-bindings-v3-3-d7f6007b530d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Remove tristate choice support from Kconfig
- Stop using the PROVIDE() directive in the linker script
- Reduce the number of links for the combination of CONFIG_KALLSYMS and
CONFIG_DEBUG_INFO_BTF
- Enable the warning for symbol reference to .exit.* sections by
default
- Fix warnings in RPM package builds
- Improve scripts/make_fit.py to generate a FIT image with separate
base DTB and overlays
- Improve choice value calculation in Kconfig
- Fix conditional prompt behavior in choice in Kconfig
- Remove support for the uncommon EMAIL environment variable in Debian
package builds
- Remove support for the uncommon "name <email>" form for the DEBEMAIL
environment variable
- Raise the minimum supported GNU Make version to 4.0
- Remove stale code for the absolute kallsyms
- Move header files commonly used for host programs to scripts/include/
- Introduce the pacman-pkg target to generate a pacman package used in
Arch Linux
- Clean up Kconfig
* tag 'kbuild-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (65 commits)
kbuild: doc: gcc to CC change
kallsyms: change sym_entry::percpu_absolute to bool type
kallsyms: unify seq and start_pos fields of struct sym_entry
kallsyms: add more original symbol type/name in comment lines
kallsyms: use \t instead of a tab in printf()
kallsyms: avoid repeated calculation of array size for markers
kbuild: add script and target to generate pacman package
modpost: use generic macros for hash table implementation
kbuild: move some helper headers from scripts/kconfig/ to scripts/include/
Makefile: add comment to discourage tools/* addition for kernel builds
kbuild: clean up scripts/remove-stale-files
kconfig: recursive checks drop file/lineno
kbuild: rpm-pkg: introduce a simple changelog section for kernel.spec
kallsyms: get rid of code for absolute kallsyms
kbuild: Create INSTALL_PATH directory if it does not exist
kbuild: Abort make on install failures
kconfig: remove 'e1' and 'e2' macros from expression deduplication
kconfig: remove SYMBOL_CHOICEVAL flag
kconfig: add const qualifiers to several function arguments
kconfig: call expr_eliminate_yn() at least once in expr_eliminate_dups()
...
|
|
Setting '-e' flag tells shells to exit with error exit code immediately
after any of commands fails, and causes make(1) to regard recipes as
failed.
Before this, make will still continue to succeed even after the
installation failed, for example, for insufficient permission or
directory does not exist.
Signed-off-by: Zhang Bingwu <xtexchooser@duck.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
|
|
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
One more Arm32 DeviceTree update for v6.11
This fixes the DeviceTree validation warning about MSM8960 /memory node
not having a unit address.
* tag 'qcom-arm32-for-6.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8960: correct memory base
Link: https://lore.kernel.org/r/20240709191506.3285-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Bindings expect the GPIO keys node names to follow certain pattern, see
dtbs_check warnings:
meson8b-ec100.dtb: gpio-keys: '#address-cells', '#size-cells' do not match any of the regexes: '^(button|event|key|switch|(button|event|key|switch)...
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240701165210.578817-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Removal of a fallback ethernet-phy compatible that is not conformant
to the binding.
* tag 'v6.11-rockchip-dts32-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Drop ethernet-phy-ieee802.3-c22 from PHY compatible string on edgeble-neu2
Link: https://lore.kernel.org/r/2169115.3Lj2Plt8kZ@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt for 6.11 (part 1)
armada-385: Add 7-segment LED display on x530
armada-385: Add Turris Omnia MCU related node
armada-370 irqchip DT changes: Drop #size-cells from mpic node
orion / kirkwood: few cleanups
* tag 'mvebu-dt-6.11-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: turris-omnia: Add GPIO key node for front button
ARM: dts: turris-omnia: Add MCU system-controller node
ARM: dts: marvell: orion: align LED node name with bindings
ARM: dts: marvell: orion5x-lswsgl: use 'gpios' property for LEDs
ARM: dts: marvell: orion: drop incorrect address/size-cells in GPIO keys
ARM: dts: marvell: orion: align GPIO keys node name with bindings
ARM: dts: marvell: kirkwood: align LED node name with bindings
ARM: dts: marvell: kirkwood: drop incorrect address/size-cells in GPIO keys
ARM: dts: marvell: kirkwood: align GPIO keys node name with bindings
ARM: dts: armada-{370-xp,375,38x,39x}: Drop #size-cells from mpic node
ARM: dts: marvell: Add 7-segment LED display on x530
Link: https://lore.kernel.org/r/87zfqvixn4.fsf@BLaptop.bootlin.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.11, round 1
Highlights:
----------
-MCU:
- Add syscfg missing clock on stm32f429.
- MPU:
- STM32MP13:
- Add camera support on stm32mp135f-dk bord using DCMIPP and
GC2145 sensor.
- Document PWM output for stm32mp135f-dk
- Add goodix touchscreen support on stm32mp135f-dk board.
- Add new DH DHCOR / DHSBC board (Som + carrier board) based on
STM32MP135F SoC.
SOM part contains: STM32MP135F SoC, 512MB DDR2L RAM and
eMMC/SDIO wifi module.
The carrier boards embedds 2 RGMII ETH ports, USB-A,USB-C
and an extansion connector.
- Add Ethernet controller support on stm32mp135f-dk.
It uses LAN8742A PHY based on RMII.
- STMP32MP15:
- Rework Octavo OSD32MP1 split for USB phy.
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- STM32MP25:
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- Enable firewall for RCC.
- Add all U(s)ART nodes for stm32mp25.
- Add 3 power domains for low power modes.
- Add HPDMA support.
- Add Ethernet controller (ETH2) support on stm32mp257f-ev1.
It uses Realtek PHY based on RGMII.
- Add and enable SCMI regulator support.
* tag 'stm32-dt-for-v6.11-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (31 commits)
arm64: dts: st: describe power supplies for stm32mp257f-ev1 board
arm64: dts: st: add scmi regulators on stm32mp25
regulator: Add STM32MP25 regulator bindings
ARM: dts: stm32: omit unused pinctrl groups from stm32mp13 dtb files
arm64: dts: st: enable Ethernet2 on stm32mp257f-ev1 board
arm64: dts: st: add eth2 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: add ethernet1 and ethernet2 support on stm32mp25
arm64: dts: st: add HPDMA nodes on stm32mp251
ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: order stm32mp13-pinctrl nodes
ARM: dts: stm32: add ethernet1 for STM32MP135F-DK board
ARM: dts: stm32: add ethernet1/2 RMII pins for STM32MP13F-DK board
ARM: dts: stm32: add ethernet1 and ethernet2 support on stm32mp13
ARM: dts: stm32: Document output pins for PWMs on stm32mp135f-dk
ARM: dts: stm32: OP-TEE async notif interrupt for ST STM32MP15x boards
ARM: dts: stm32: Missing clocks for stm32f429's syscfg.
ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board
ARM: dts: stm32: Add pinmux nodes for DH electronics STM32MP13xx DHCOR SoM and DHSBC board
dt-bindings: arm: stm32: Add compatible string for DH electronics STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: osd32: move pwr_regulators to common
...
Link: https://lore.kernel.org/r/8f10bd29-d067-4060-89ff-2e1a605f3141@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v6.11
This introduces new support for the Sony Xperia Z3 Compact, HTC One
(M8), Samsung Galaxy Tab 4 8.0 Wi-Fi, Samsung Galaxy Grand 2, and
Samsung Galaxy Note 3 devices.
The Motorola Moto G and Motorola Moto G 4G gains accelerometer and
magnetometer support, with the latter also getting framebuffer supplies
and a temperature sensor wired up.
The SMBB (charger block) is enabled across all MSM8x26 Lumia devices, as
this is used for USB state changes.
The operating mode for SDC regulator is set to HPM on Sony Xperia
"Shinano" family to avoid brownouts on uSD-cards.
The panel on LGE Nexus 5 is connected to the backlight, to make this
turn off on blanking.
MSM8974 is transitioned to use the mailbox-abstraction for invoking
PC interrupts on remote processors.
* tag 'qcom-arm32-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (24 commits)
ARM: dts: qcom: qcom-msm8226-samsung-ms013g: Add initial device tree
ARM: dts: qcom: apq8064: drop incorrect ranges from QFPROM
ARM: dts: qcom: msm8926-motorola-peregrine: Add framebuffer supplies
ARM: dts: qcom: msm8926-motorola-peregrine: Update temperature sensor
ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator
ARM: dts: qcom: msm8974: Use mboxes in smsm node
ARM: dts: qcom: msm8974-sony-shinano: increase load on l21 for sdhc2
ARM: dts: qcom: Add Sony Xperia Z3 Compact smartphone
ARM: dts: qcom: use generic node names for Adreno and QFPROM
ARM: dts: qcom: motorola-falcon: add accelerometer, magnetometer
ARM: dts: qcom: Add initial support for HTC One (M8)
ARM: dts: qcom: msm8974: Use mboxes properties for APCS
ARM: dts: qcom: mdm9615: drop #power-domain-cells property of GCC
ARM: dts: qcom: ipq8064: drop #power-domain-cells property of GCC
ARM: dts: qcom: ipq4019: drop #power-domain-cells property of GCC
ARM: dts: qcom: msm8960: drop #power-domain-cells property of GCC
ARM: dts: qcom: msm8660: drop #power-domain-cells property of GCC
ARM: dts: qcom: apq8064: drop #power-domain-cells property of GCC
ARM: dts: qcom: msm8974: Use proper compatible for APCS syscon
ARM: dts: qcom: msm8974-hammerhead: Update gpio hog node name
...
Link: https://lore.kernel.org/r/20240705032926.13333-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The beeper in the NSLU2 is just a GPIO connected to a
speaker, so we need to use PWM on the GPIO to get any kind
of sound out.
Tested with some random beeps by enabling INPUT_EVDEV and
running beep.c with e.g. beep 400 for a 400 Hz tone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/20240627-ixp4xx-dts-v1-1-cdbbe1150873@linaro.org
Link: https://lore.kernel.org/r/20240703-ixp4xx-dts-v1-1-e5149da36f6e@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner SoC device tree changes for 6.11
This includes a commit shared with the clk tree. This commit adds clock
and reset indices to the device tree binding, and thus is needed for
both the device tree and driver changes.
ARM64 device tree and binding-only changes
- Add LRADC (low resolution ADC for resistor network based keys) for H616 SoC
- Add cache information for A64, H6, and H616 SoCs
- Correct model names and descriptions for Pine64 boards
- Add GPADC (general purpose ADC) for H616 SoC
- Add ADC joysticks based on GPADC for anbernic-rg35xx-h board
- Add additional CPU OPPs for the H700 on top of existing H616 ones
- Enable DVFS for rg35xx boards
- Add IOMMU for H616 SoC
RISC-V device tree changes
- Add system LDOs to D1s/T113 SoC
- Add ClockworkPi and DevTerm device trees
* tag 'sunxi-dt-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: Add ClockworkPi and DevTerm devicetrees
riscv: dts: allwinner: d1s-t113: Add system LDOs
arm64: dts: allwinner: h616: add IOMMU node
arm64: dts: allwinner: rg35xx: Enable DVFS CPU frequency scaling
arm64: dts: allwinner: h616: add additional CPU OPPs for the H700
arm64: dts: allwinner: anbernic-rg35xx-h: Add ADC joysticks
arm64: dts: allwinner: h616: Add GPADC device node
dt-bindings: clock: sun50i-h616-ccu: Add GPADC clocks
ARM: dts: sunxi: remove duplicated entries in makefile
arm64: dts: allwinner: Add cache information to the SoC dtsi for H616
arm64: dts: allwinner: Add cache information to the SoC dtsi for A64
arm64: dts: allwinner: Correct the model names for Pine64 boards
dt-bindings: arm: sunxi: Correct the descriptions for Pine64 boards
arm64: dts: allwinner: Add cache information to the SoC dtsi for H6
ARM: dts: sun50i: Add LRADC node
dt-bindings: input: sun4i-lradc-keys: Add H616 compatible
Link: https://lore.kernel.org/r/ZoQa8r1N8yi7FlPV@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.11:
- A few changes from Krzysztof Kozlowski to fix dtschema issues
- A series from Michael Walle to improve kontron-samx6i SoM support by
fixing various errors and add kontron-samx6i-ads2 board
- Add LVDS port data mapping for M53 Menlo board
- Convert NVMEM usage to layout syntax on MBA6 boards
* tag 'imx-dt-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-kontron-samx6i: add actual device trees
ARM: dts: imx6qdl-kontron-samx6i: remove wake-up-gpio property
ARM: dts: imx6qdl-kontron-samx6i: fix PCIe reset polarity
ARM: dts: imx6qdl-kontron-samx6i: fix node names
ARM: dts: imx6qdl-kontron-samx6i: add SDIO_PWR_EN support
ARM: dts: imx6qdl-kontron-samx6i: always enable eMMC
ARM: dts: imx6qdl-kontron-samx6i: fix product name
ARM: dts: imx6qdl-kontron-samx6i: fix SPI0 chip selects
ARM: dts: imx6qdl-kontron-samx6i: cleanup the PMIC node
ARM: dts: imx6qdl-kontron-samx6i: fix board reset
ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset
ARM: dts: imx6qdl-kontron-samx6i: fix phy-mode
ARM: dts: nxp: imx6: convert NVMEM content to layout syntax
ARM: dts: e60k02: fix aliases for mmc
ARM: dts: imx: Add LVDS port data mapping on M53 Menlo
ARM: dts: imx28-tx28: drop redundant 'panel-name' property
ARM: dts: imx: drop redundant 'u-boot,panel-name' property
ARM: dts: imx6dl-aristainetos2_4: drop redundant 'power-on-delay' property
ARM: dts: imx: correct choice of panel native mode
ARM: dts: imx: align panel timings node name with dtschema
Link: https://lore.kernel.org/r/20240702142153.413061-3-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.11
Few cleanups and improvements which were missed by their maintainers:
1. Add Krzysztof as odd-fixer for old ARM platforms: Alphascale, AXM
LSI, Moxa, TI Nspire and VT8500 (with Alexey Charkov).
2. VT8500: align node names with bindings (USB, panel timings).
3. Cirrus: align node names with bindings (panel timings).
4. TI Nspire: correct unit addresses, correct watchdog compatible and
properties while making it disabled (never tested).
5. Nuvoton, Aspeed: align node names with bindings (I2C).
IMPORTANT: At least for Aspeed it is known to affect some user-space
tools, because that user-space looks for specific node path via
/sys/firmware/devicetree. The /sys/firmware/devicetree is not the ABI
and any user-space relying on it:
- Prevents any changes in DTS, e.g. node renaming or moving,
changing unit addresses (re-arranging child bus addressing).
- Is using undocumented interface.
- Is neither reliable nor understandable.
6. TI OMAP and Davinci: align node names with bindings (panel timings),
drop incorrect property.
7. STI: document in bindings codec child to fix dtbs_checks.
* tag 'dt-cleanup-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: omap am5729-beagleboneai: drop unneeded ti,enable-id-detection
dt-bindings: soc: sti: st,sti-syscon: document codec node
ARM: dts: ti: align panel timings node name with dtschema
arm: dts: aspeed: Use standard 'i2c' bus node name
arm: dts: nuvoton: Use standard 'i2c' bus node name
MAINTAINERS: ARM: alphascale: add Krzysztof Kozlowski as maintainer
ARM: dts: nspire: Add full compatible for watchdog node
ARM: dts: nspire: Add unit name addresses to memory nodes
MAINTAINERS: ARM: nspire: add Krzysztof Kozlowski as maintainer
MAINTAINERS: ARM: vt8500: add Alexey and Krzysztof as maintainers
MAINTAINERS: ARM: axm: add Krzysztof Kozlowski as maintainer
MAINTAINERS: ARM: moxa: add Krzysztof Kozlowski as maintainer
ARM: dts: cirrus: align panel timings node name with dtschema
ARM: dts: vt8500: align panel timings node name with dtschema
ARM: dts: vt8500: replace "uhci" nodename with generic name "usb"
Link: https://lore.kernel.org/r/20240702065359.7378-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
DeviceTree validation requires a unit address on the memory node, adjust
the base to match [Ref] and use this as unit address.
The bootloader will update the information with the actual values during
boot.
Ref: https://github.com/msm8916-mainline/lk2nd/blob/main/target/msm8960/rules.mk
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20240706220041.241839-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Now that we have the MCU device-tree node, which acts as a GPIO
controller, add GPIO key node for the front button.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lun |
