| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Reserve 128MiB of global CMA which is also marked as re-usable
so that OS can also use the same if peripheral drivers are not using the
same.
AM62x supports multimedia components such as GPU, dual Display and Camera.
Assuming the worst-case scenario where all 3 are run in parallel below
is the calculation :
1) OV5640 camera sensor supports 1920x1080 resolution
-> 1920 width x 1080 height x 2 bytesperpixel x 8 buffers
(default in yavta) : 32MiB
2) 1920x1200 Microtips LVDS panel supported
-> 1920 width x 1080 height x 4 bytesperpixel x 2 buffers :
16 MiB
3) 1920x1080 HDMI display supported
-> 1920 width x 1080 height x 4 bytesperpixel x 2 buffers :
15.82 MiB which is ~16 MiB
4) IMG GPU shares with display allocated buffers while rendering
but in case some dedicated operation viz color conversion,
keeping same window of ~16 MiB for GPU too.
Total is 80 MiB and adding 32 MiB for other peripherals and extra
16 MiB to keep as buffer for fragmentation thus rounding total to 128
MiB.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Randolph Sapp <rs@ti.com>
Link: https://lore.kernel.org/r/20240613150902.2173582-2-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Replace the fixed regulator for USB VBUS and use the proper one that
controls regulator based on VBUS detection.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240702180032.207275-5-biju.das.jz@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
ASUS Vivobook S 15 is a laptop based on the Qualcomm Snapdragon X Elite
SoC (X1E78100).
Add the device tree for the laptop with support for the following features:
- CPU frequency scaling up to 3.4GHz
- NVMe storage on PCIe 6a (capable of Gen4x4, currently limited to Gen4x2)
- Keyboard and touchpad
- WCN7850 Wi-Fi
- Two Type-C ports on the left side (USB3 only in one orientation)
- internal eDP display
- ADSP and CDSP remoteprocs
Further details could be found in the cover letter.
Signed-off-by: Xilin Wu <wuxilin123@gmail.com>
Link: https://lore.kernel.org/r/20240701-asus-vivobook-s15-v4-2-ce7933b4d4e5@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
According to downstream sources, maximum current for PMI632 VBUS
is 1A.
Taken from msm-4.19 (631561973a034e46ccacd0e53ef65d13a40d87a4)
Line 685-687 in drivers/power/supply/qcom/qpnp-smb5.c
Fixes: a06a2f12f9e2 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240702-qrd4210rb2-vbus-volt-v3-1-fbd24661eec4@riseup.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Now that the venus clocks are fixed, we can add the DT node.
Signed-off-by: Pierre-Hugues Husson <phhusson@freebox.fr>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Link: https://lore.kernel.org/r/6d86a6a3-4d99-4fda-9a38-7688587237e6@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
According to nxp,dwmac-imx.yaml, 'snps,rx-sched-sp' is not a valid
property.
Remove it from the imx8mp board devicetree files to avoid
dt-schema warnings:
... 'snps,tx-sched-sp' does not match any of the regexes
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Revision 3 of the sa8775p-ride board uses a different PHY for the two
ethernet ports and supports 2.5G speed. Create a new file for the board
reflecting the changes.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240627114212.25400-4-brgl@bgdev.pl
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
In order to support multiple revisions of the sa8775p-ride board, create
a .dtsi containing the common parts and split out the ethernet bits into
the actual board file as they will change in revision 3.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240627114212.25400-3-brgl@bgdev.pl
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker. This
solves second (south) speaker sound distortions when playing audio.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240627122015.30945-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker. This
solves second (right) speaker sound distortions when playing audio.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240627122015.30945-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker. This
solves second (south) speaker sound distortions when playing audio.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240627122015.30945-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker
to correctly map the Speaker ports to the WSA macro ports.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240627-topic-sm8650-upstream-was-port-mapping-v1-3-4700bcc2489a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker
to correctly map the Speaker ports to the WSA macro ports.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240627-topic-sm8650-upstream-was-port-mapping-v1-2-4700bcc2489a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add appropriate mappings of Soundwire ports of WSA8845 speaker
to correctly map the Speaker ports to the WSA macro ports.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240627-topic-sm8650-upstream-was-port-mapping-v1-1-4700bcc2489a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Without explicitly specifying names for the regulators they are named
based on the DeviceTree node name. This results in multiple regulators
with the same name, making debug prints and regulator_summary impossible
to reason about.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240627-fp4-regulator-name-v1-1-66931111a006@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Correct the name for the thermal zone on PM8916 PMIC. I ended up with
c&p mistake, which wasn't noticed until the patch got merged.
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: b7a28d8a7b80 ("arm64: dts: qcom: pm8916: add temp-alarm thermal zone")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240701-fix-pm8916-tz-v1-1-02f8a713f577@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the necessary dt nodes for gpu support in X1E80100.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240629015111.264564-6-quic_akhilpo@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
According to the power grid documentation, the 0.8v HS PHY shared
regulator is actually LDO3 from PM8550ve id J. Fix both CRD and QCP
boards.
Fixes: d7e03cce0400 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240629-x1e80100-dts-fix-hsphy-0-8v-supplies-v1-1-de99ee030b27@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Fix the following warnings when compiling dtbs with W=1:
../arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi:343.10-353.6: Warning (graph_child_address): /bus@f0000/i2c@20000000/tps6598x@3f/connector/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
../arch/arm64/boot/dts/ti/k3-am62-main.dtsi:633.22-643.5: Warning (graph_child_address): /bus@f0000/dwc3-usb@f900000/usb@31000000: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240626101520.1782320-3-d-gole@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Fix the following warnings that are thrown when building dtbs with W=1:
../arch/arm64/boot/dts/ti/k3-am62p5-sk.dts:367.10-376.6: Warning (graph_child_address): /bus@f0000/i2c@20000000/usb-power-controller@3f/connector/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
../arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi:647.22-657.5: Warning (graph_child_address): /bus@f0000/usb@f900000/usb@31000000: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
also defined at ../arch/arm64/boot/dts/ti/k3-am62p5-sk.dts:517.7-528.3
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240626101520.1782320-2-d-gole@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The AM67A/J722S/TDA4AEN platform is a derivative of AM62P platform
and we have no single 1:1 relation regarding index of GPIO and pin
controller. The GPIOs and pin controller registers have mapping and
holes in the map. These have been extracted from the J722S data
sheet. The MCU mapping is carried forward as is with J722S, however the
main GPIO block has differences that needs to be accounted for.
Mux mode input is selected as it is bi-directional. In case a specific
pull type or a specific pin level drive setting is desired, the board
device tree files will have to explicitly mux those pins for the GPIO
with the desired setting.
Ref: J722S Data sheet https://www.ti.com/lit/gpn/tda4aen-q1
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On the AM62P platform we have no single 1:1 relation regarding index
of GPIO and pin controller. The GPIOs and pin controller registers
have mapping and holes in the map. These have been extracted from the
AM62P data sheet.
MCU pinctrl definition is shared as it is common between AM62P and
J722S, but that is not the case for main domain.
Ref: AM62P Data sheet https://www.ti.com/lit/gpn/am62p
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Introduce a GPIO mux mode macro for easier readability. All K3 devices
use mux mode 7 to switch to GPIO mux and this allows the gpio-ranges to
be defined for pinctrl-single clearly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The WKUP system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-8-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The WKUP system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-7-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-6-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
NAND boot would require these nodes to be present at early stage.
Ensure that by adding "bootph-all" to relevant nodes.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240628-am642-evm-nand-bootph-v2-1-387bfa1533a6@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The phyCORE-AM62Ax [1] is a SoM (System on Module) featuring TI's AM62Ax SoC.
It can be used in combination with different carrier boards.
This module can come with different sizes and models for
DDR, eMMC, SPI NOR Flash and various SoCs from the AM62Ax family.
A development Kit, called phyBOARD-Lyra [2] is used as a carrier board
reference design with a mapper board being used to allow the phyCORE-AM62Ax
to fit the phyBOARD-Lyra.
Supported features:
* Debug UART
* SPI NOR Flash
* eMMC
* 2x Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* GPIO Expander
* LEDs
* USB
* HDMI
* USB-C
* Audio
For more details, see:
[1] Product page SoM: https://www.phytec.com/product/phycore-am62a
[2] Product page CB: https://www.phytec.com/product/phyboard-am62a
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240626155244.3311436-4-ggiordano@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
PHYTECs phyBOARD-Lyra carrier board is able to accomidate multiple SoMs.
Refactor k3-am625-phyboard-lyra-rdk.dts into an include file so it can
be reused in combination with our phyCORE-AM62Ax SoM.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240626155244.3311436-2-ggiordano@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On AM62a SoCs the AUDIO_REFCLKx clocks can be used as an input to
external peripherals when configured through CTRL_MMR, so add the
clock nodes.
Based on: Link: https://lore.kernel.org/lkml/20230807202159.13095-2-francesco@dolcini.it/
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Link: https://lore.kernel.org/r/20240626155244.3311436-1-ggiordano@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The audio support on J784S4-EVM is using PCM3168A[0] codec
connected to McASP0 serializers.
- Add the nodes for sound-card, audio codec, MAIN_I2C3 and
McASP0.
- Add pinmux for I2C3, McASP0 and AUDIO_EXT_REFCLK1.
- Add necessary GPIO hogs to route the MAIN_I2C3 lines and
McASP serializer.
- Add idle-state as 1 in mux1 to route McASP clock signals.
[0]: <https://www.ti.com/lit/gpn/pcm3168a>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-4-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On J784S4 SoC, the AUDIO_REFCLK1 can be used as input to external
peripherals when configured through CTRL_MMR.
Add audio_refclk1 node which would be used as system clock for
audio codec PCM3168A.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add McASP 0-4 instances and keep them disabled because several
required properties are missing as they are board specific.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The NAND expansion card (PROC143E1) connects over the User/MCU/PRU
Expansion port on the am62-lp-sk EVM.
The following pins are shared between McASP1 and GPMC-NAND so
both cannot work simultaneously.
Pin name McASP1 function GPMC function
======== =============== =============
J17 MCASP1_AXR0 GPMC0_WEN
P21 MCASP1_AFSX GPMC0_WAIT0
K17 MCASP1_ACLKX GPMC0_BE0N_CLE
K20 MCASP1_AXR2 GPMC0_ADVN_ALE
The factory default sets the pins for McASP1 use. (i.e.
Resistor Array RA1 installed, RA4 not installed).
For NAND use, RA1 has to be removed and RA4 must be
installed.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-2-caee496eaf42@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add GPMC and ELM device tree nodes for AM62 SoC family.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-1-caee496eaf42@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The audio support on J722S-EVM is using TLV320AIC3106[0] codec
connected to McASP1 serializers.
- Add the nodes for sound-card, audio codec and McASP1.
- Add hog for TRC_MUX_SEL to select between McASP and TRACE signals
- Add hogs for GPIO_AUD_RSTn and MCASP1_FET_SEL which is used to
switch between HDMI audio and codec audio.
- Add pinmux for MCASP1 and AUDIO_EXT_REFCLK1.
[0]: <https://www.ti.com/lit/gpn/TLV320AIC3106>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
On J722S SoC, the AUDIO_REFCLK1 can be used as input to external
peripherals when configured through CTRL_MMR.
Add audio_refclk1 node which would be used as system clock for the
audio codec TLV320AIC3106.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240622161835.3610348-1-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add an overlay to change from the default OSPI NOR to QSPI NOR
for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if qspi nor is populated, the EEPROM will
indicate that change and we can use this overlay to cleanly change to
qspi nor.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240621233143.2077941-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MIT license was added to the AM64x SoC DTSIs in commit 6248b20e3203
("arm64: dts: ti: k3-am64: Add MIT license along with GPL-2.0"). Apply
the same license change to the TQMa64xxL SoM and MBaX4XxL baseboard
Device Trees.
The copyright year is updated to indicate the license change.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240625110244.9881-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
In current configuration, nau8822 codec on development carrier board
provides distorted audio output. This happens due to reference clock
is fixed to 25MHz and no PLL is enabled. Following is the calculation
of deviation error for different frequencies:
44100Hz:
fs = 256 (fixed)
prescaler = 2
target frequency = 44100 * 256 * 2 = 22579200
deviation = 22579200 vs 25000000 = 9.6832%
48000Hz:
fs = 256 (fixed)
prescaler = 2
target frequency = 48000 * 256 * 2 = 24576000
deviation = 24576000 vs 25000000 = 1.696%
Enabling nau822 PLL via providing mclk-fs property to simple-audio-card
configures clocks properly, but also adjusts audio reference clock
(mclk), which in case of TI AM62 should be avoided, as it only
supports 25MHz output [1][2].
This change enables PLL on nau8822 by providing mclk-fs, and moves
away audio reference clock from DAI configuration, which prevents
simple-audio-card to adjust it before every playback [3].
[1]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1175479/processor-sdk-am62x-output-audio_ext_refclk0-as-mclk-for-codec-and-mcbsp/4444986#4444986
[2]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1188051/am625-audio_ext_refclk1-clock-output---dts-support/4476322#4476322
[3]: sound/soc/generic/simple-card-utils.c#L441
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240418105730.120913-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add TPM device found on Verdin iMX8M Mini PID4 0090 variant.
While adding the node, rename `pinctrl_pmic_tpm_ena` to
`pinctrl_tpm_spi_cs`.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add audio XCVR sound card, which supports SPDIF TX & RX,
eARC RX, ARC RX functions.
HDMI_HPD is shared with the HDMI module so use pinctrl_hog.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
XCVR (Audio Transceiver) is a on-chip functional module found
on i.MX8MP. It supports HDMI2.1 eARC, HDMI1.4 ARC and SPDIF.
The reset controller is provided by the audio block control driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8MP DHCOM rev.200
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.
Prototype rev.100 SoM was never publicly available and was manufactured in
limited series, anything currently available is rev.200 or newer, so it is
safe to update the DT this way.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DH i.MX8M Plus DHCOM SoM uses Audio PLL2 to supply clock to CLKOUT2
output. Those clock are used to supply on-SoM TC9595 DSI-to-(e)DP bridge
with RefClk and must not be reconfigured, otherwise the bridge cannot
work correctly. Stop reconfiguring Audio PLL2 on this SoM.
Fixes: f560da940e32 ("arm64: dts: imx8mp: Initialize audio PLLs from audiomix subsystem")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
