| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit cb31334687db31c691901269d65074a7ffaecb18 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: b004a34bd0ff ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 36bf1dfb8b266e089afa9b7b984217f17027bf35 upstream.
set_phys_to_machine can fail due to lack of memory, see the kzalloc call
in arch/arm/xen/p2m.c:__set_phys_to_machine_multi.
Don't ignore the potential return error in set_foreign_p2m_mapping,
returning it to the caller instead.
This is part of XSA-361.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Cc: stable@vger.kernel.org
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d62e81b60d4025e2dfcd5ea531cc1394ce9226f ]
Giancarlo Ferrari reports the following oops while trying to use kexec:
Unable to handle kernel paging request at virtual address 80112f38
pgd = fd7ef03e
[80112f38] *pgd=0001141e(bad)
Internal error: Oops: 80d [#1] PREEMPT SMP ARM
...
This is caused by machine_kexec() trying to set the kernel text to be
read/write, so it can poke values into the relocation code before
copying it - and an interrupt occuring which changes the page tables.
The subsequent writes then hit read-only sections that trigger a
data abort resulting in the above oops.
Fix this by copying the relocation code, and then writing the variables
into the destination, thereby avoiding the need to make the kernel text
read/write.
Reported-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Tested-by: Giancarlo Ferrari <giancarlo.ferrari89@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c698bff66ab4914bb3d71da7dc6112519bde23e ]
Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5638159f6d93b99ec9743ac7f65563fca3cf413d ]
This reverts commit c17e9377aa81664d94b4f2102559fcf2a01ec8e7.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06862d789ddde8a99c1e579e934ca17c15a84755 ]
We get suspcious RCU usage splats with cpuidle in several places in
omap_enter_idle_coupled() with the kernel debug options enabled:
RCU used illegally from extended quiescent state!
...
(_raw_spin_lock_irqsave)
(omap_enter_idle_coupled+0x17c/0x2d8)
(omap_enter_idle_coupled)
(cpuidle_enter_state)
(cpuidle_enter_state_coupled)
(cpuidle_enter)
Let's use RCU_NONIDLE to suppress these splats. Things got changed around
with commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path") that started triggering these warnings.
For the tick_broadcast related calls, ideally we'd just switch over to
using CPUIDLE_FLAG_TIMER_STOP for omap_enter_idle_coupled() to have the
generic cpuidle code handle the tick_broadcast related calls for us and
then just drop the tick_broadcast calls here.
But we're currently missing the call in the common cpuidle code for
tick_broadcast_enable() that CPU1 hotplug needs as described in earlier
commit 50d6b3cf9403 ("ARM: OMAP2+: fix lack of timer interrupts on CPU1
after hotplug").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c4295ab0b485b8bc50d2264bcae2acd06f25caaf upstream.
After Commit 3499ba8198cad ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org
Fixes: 3499ba8198cad ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 538eea5362a1179dfa7770dd2b6607dc30cc50c6 upstream.
The tegra_uart_config of the DEBUG_LL code is now placed right at the
start of the .text section after commit which enabled debug output in the
decompressor. Tegra devices are not booting anymore if DEBUG_LL is enabled
since tegra_uart_config data is executes as a code. Fix the misplaced
tegra_uart_config storage by embedding it into the code.
Cc: stable@vger.kernel.org
Fixes: 2596a72d3384 ("ARM: 9009/1: uncompress: Enable debug in head.S")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39d3454c3513840eb123b3913fda6903e45ce671 upstream.
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 181739822cf6f8f4e12b173913af2967a28906c0 upstream.
With the arrival of
commit 2fee9583198eb9 ("spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors")
it was clarified what the proper state for cs-gpios should be, even if the
flag is ignored. The driver code is doing the right thing since
766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
The chip-select of the td028ttec1 panel is active-low, so we must omit spi-cs-high;
attribute (already removed by separate patch) and should now use GPIO_ACTIVE_LOW for
the client device description to be fully consistent.
Fixes: 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07af7810e0a5bc4e51682c90f9fa19fc4cb93f18 upstream.
This reverts
commit f1f028ff89cb ("DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again")
which had to be intruduced after
commit 6953c57ab172 ("gpio: of: Handle SPI chipselect legacy bindings")
broke the GTA04 display. This contradicted the data sheet but was the only
way to get it as an spi client operational again.
The panel data sheet defines the chip-select to be active low.
Now, with the arrival of
commit 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
the logic of interaction between spi-cs-high and the gpio descriptor flags
has been changed a second time, making the display broken again. So we have
to remove the original fix which in retrospect was a workaround of a bug in
the spi subsystem and not a feature of the panel or bug in the device tree.
With this fix the device tree is back in sync with the data sheet and
spi subsystem code.
Fixes: 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
CC: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a900cac3750b9f0b8f5ed0503d9c6359532f644d ]
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dcd9 ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 83d411224025ac1baab981e3d2f5d29e7761541d ]
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 087698939f30d489e785d7df3e6aa5dce2487b39 ]
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 063a60634d48ee89f697371c9850c9370e494f22 ]
The uSD slot has no WP detection, disable it.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a9b001237f85d3cf11a408c2daca6a2245b2add ]
The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a0572c0734e4926ac51a31f97c12f752e1cdc7c8 ]
The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6efac0173cd15460b48c91e1b0a000379f341f00 ]
Commit 45c5775460f3 ("usb: ohci-omap: Fix descriptor conversion") tried to
fix all issues related to ohci-omap descriptor conversion, but a wrong
patch was applied, and one needed change to the OSK board file is still
missing. Fix that.
Fixes: 45c5775460f3 ("usb: ohci-omap: Fix descriptor conversion")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[aaro.koskinen@iki.fi: rebased and updated the changelog]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 28187dc8ebd938d574edfc6d9e0f9c51c21ff3f4 upstream.
LLD does not yet support any big endian architectures. Make this config
non-selectable when using LLD until LLD is fixed.
Link: https://github.com/ClangBuiltLinux/linux/issues/965
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2cc0bfc9c12784188482a8f3d751d44af45b0d97 ]
The PHY address bit 2 is configured by the LED pin. Attaching a LED
to this pin is not sufficient to guarantee this configuration pin is
correctly read. This leads to some platforms having their PHY at
address 0 and others at address 4.
If there is no phy-handle specified, the FEC driver will scan the PHY
bus for a PHY and use that. Consequently, adding the DT configuration
of the PHY and the phy properties to the FEC driver broke some boards.
Fix this by removing the phy-handle property, and listing two PHY
entries for both possible PHY addresses, so that the DT configuration
for the PHY can be found by the PHY driver.
Fixes: 86b08bd5b994 ("ARM: dts: imx6-sr-som: add ethernet PHY configuration")
Reported-by: Christoph Mattheis <christoph.mattheis@arcor.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70b6ff4c549a62b59b286445f66cfec6c5327ac8 ]
Fix typo so the gpio i2c busses are really disabled.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 30596ae0547dbda469d31a2678d9072fb0a3fa27 upstream.
Commit 7536c7e03e74 ("of/fdt: Remove redundant kbasename function
call") exposed a bug creating DT nodes in the ATAGS to DT fixup code.
Non-existent nodes would mistaken get created with a leading '/'. The
problem was fdt_path_offset() takes a full path while creating a node
with fdt_add_subnode() takes just the basename.
Since this we only add root child nodes, we can just skip over the '/'.
Fixes: 7536c7e03e74 ("of/fdt: Remove redundant kbasename function call")
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Qi Zheng <arch0.zheng@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210126023905.1631161-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a88afa46b86ff461c89cc33fc3a45267fff053e8 upstream.
When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).
It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.
Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Fixes: df595746fa69 ("ARM: imx: add suspend in ocram support for i.mx6q")
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6337c2353a069b6f1276dc35421e421ef6c1ead9 upstream.
The pwms property have to specify the no-/inverted flag since
commit fa28d8212ede ("ARM: dts: imx: default to #pwm-cells = <3>
in the SoC dtsi files").
Fixes: fa28d8212ede ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a22747b76ca2384057d8e783265404439d31d7f upstream.
2 regulator descriptions carry identical naming.
This leads to following boot warning:
[ 0.173138] debugfs: Directory 'vdd1p8' with parent 'regulator' already present!
Fix this by renaming the one used for audio.
Fixes: 5051bff33102 ("ARM: dts: imx: ventana: add LTC3676 PMIC support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a996b2d8a03beae3cb6adfc12673778c192085d upstream.
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9c9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd25c883667b61f845a4188b6be110bb45de0bac upstream.
to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3499ba8198cad47b731792e5e56b9ec2a78a83a2 ]
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bac717171971176b78c72d15a8b6961764ab197f ]
dtc points out that the interrupts for some devices are not parsable:
picoxcell-pc3x2.dtsi:45.19-49.5: Warning (interrupts_property): /paxi/gem@30000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:51.21-55.5: Warning (interrupts_property): /paxi/dmac@40000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:57.21-61.5: Warning (interrupts_property): /paxi/dmac@50000: Missing interrupt-parent
picoxcell-pc3x2.dtsi:233.21-237.5: Warning (interrupts_property): /rwid-axi/axi2pico@c0000000: Missing interrupt-parent
There are two VIC instances, so it's not clear which one needs to be
used. I found the BSP sources that reference VIC0, so use that:
https://github.com/r1mikey/meta-picoxcell/blob/master/recipes-kernel/linux/linux-picochip-3.0/0001-picoxcell-support-for-Picochip-picoXcell-SoC.patch
Acked-by: Jamie Iles <jamie@jamieiles.com>
Link: https://lore.kernel.org/r/20201230152010.3914962-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7887cc89d5851cbdec49219e9614beec776af150 ]
A too high brightness by default (default is max) makes the
screen go blank. Set this to 15 as in the Vendor tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20201214223413.253893-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
on xt875
[ Upstream commit c0bc969c176b10598b31d5d1a5edf9a5261f0a9f ]
xt875 comes up with a iva voltage of 1375000 and android runs at this too. fix
maximum voltage to be consistent with this.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ec76c2eea903947202098090bbe07a739b5246e9 upstream.
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c04 ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6d5 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1dc15cd7fc146107cad2a926d9c1d005f69002a upstream.
AES needs to be disabled on Nokia N950/N9 as well (HS devices), otherwise
kernel fails to boot.
Fixes: c312f066314e ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 87dbc209ea04645fd2351981f09eff5d23f8e2e9 ]
Make <asm-generic/local64.h> mandatory in include/asm-generic/Kbuild and
remove all arch/*/include/asm/local64.h arch-specific files since they
only #include <asm-generic/local64.h>.
This fixes build errors on arch/c6x/ and arch/nios2/ for
block/blk-iocost.c.
Build-tested on 21 of 25 arch-es. (tools problems on the others)
Yes, we could even rename <asm-generic/local64.h> to
<linux/local64.h> and change all #includes to use
<linux/local64.h> instead.
Link: https://lkml.kernel.org/r/20201227024446.17018-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bd7cd7e05a42491469ca19861da44abc3168cf5f upstream.
Commit 9ce274630495 ("cpufreq: tegra20: Use generic cpufreq-dt driver
(Tegra30 supported now)") update the Tegra20 CPUFREQ driver to use the
generic CPUFREQ device-tree driver. Since this change CPUFREQ support
on the Tegra20 Ventana platform has been broken because the necessary
device-tree nodes with the operating point information are not populated
for this platform. Fix this by updating device-tree for Venata to
include the operating point informration for Tegra20.
Fixes: 9ce274630495 ("cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported now)")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85b8350ae99d1300eb6dc072459246c2649a8e50 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666b7 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit df9dbaf2c415cd94ad520067a1eccfee62f00a33 upstream.
The pinmux control register offset passed to OMAP4_IOPAD is odd.
Fixes: ab9a13665e7c ("ARM: dts: pandaboard: add gpio user button")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3456b9fd269c6d0c973b136c5449d46b2510f4b upstream.
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
[0] ARM-EPM-049219 v23 Cortex-A57 MPCore Software Developers Errata Notice
[1] ARM-EPM-012079 v11.0 Cortex-A72 MPCore Software Developers Errata Notice
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1ecec38547d415054fdb63a231234f44396b6d06 ]
The dbgadtb macro is passed the size of the appended DTB, not the end
address.
Fixes: c03e41470e901123 ("ARM: 9010/1: uncompress: Print the location of appended DTB")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3cce9d44321e460e7c88cdec4e4537a6e9ad7c0d ]
Commit f77ac2e378be9dd6 ("ARM: 9030/1: entry: omit FP emulation for UND
exceptions taken in kernel mode") failed to take into account that there
is in fact a case where we relied on this code path: during boot, the
VFP detection code issues a read of FPSID, which will trigger an undef
exception on cores that lack VFP support.
So let's reinstate this logic using an undef hook which is registered
only for the duration of the initcall to vpf_init(), and which sets
VFP_arch to a non-zero value - as before - if no VFP support is present.
Fixes: f77ac2e378be9dd6 ("ARM: 9030/1: entry: omit FP emulation for UND ...")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f77ac2e378be9dd61eb88728f0840642f045d9d1 ]
There are a couple of problems with the exception entry code that deals
with FP exceptions (which are reported as UND exceptions) when building
the kernel in Thumb2 mode:
- the conditional branch to vfp_kmode_exception in vfp_support_entry()
may be out of range for its target, depending on how the linker decides
to arrange the sections;
- when the UND exception is taken in kernel mode, the emulation handling
logic is entered via the 'call_fpe' label, which means we end up using
the wrong value/mask pairs to match and detect the NEON opcodes.
Since UND exceptions in kernel mode are unlikely to occur on a hot path
(as opposed to the user mode version which is invoked for VFP support
code and lazy restore), we can use the existing undef hook machinery for
any kernel mode instruction emulation that is needed, including calling
the existing vfp_kmode_exception() routine for unexpected cases. So drop
the call to call_fpe, and instead, install an undef hook that will get
called for NEON and VFP instructions that trigger an UND exception in
kernel mode.
While at it, make sure that the PC correction is accurate for the
execution mode where the exception was taken, by checking the PSR
Thumb bit.
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Fixes: eff8728fe698 ("vmlinux.lds.h: Add PGO and AutoFDO input sections")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 656ab1bdcd2b755dc161a9774201100d5bf74b8d ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: a2c6e82e5341 ("ARM: dts: meson: switch to the generic Ethernet PHY reset bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # on Odroid-C1+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/ff78772b306411e145769c46d4090554344db41e.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b5dcc8d427e2bcb84c49eb03ffefe11e7537a55 ]
Due to strobe signal not being propagated from CPU to securam
the securam needs to be mapped as device or strongly ordered memory
to work properly. Otherwise, updating to one offset may affect
the adjacent locations in securam.
Fixes: d4ce5f44d4409 ("ARM: dts: at91: sama5d2: Add securam node")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab8a9bb41b2c330a0b280280bf37b6f3b1dd1e58 ]
atmel,osc-bypass property sets the bit 1 at main oscillator register.
On SAM9X60 this bit is not valid according to datasheet (chapter
28.16.9 PMC Clock Generator Main Oscillator Register).
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Marco Cardellini <marco.cardellini@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 851a95da583c26e2ddeb7281e9b61f0d76ea5aba ]
The triggers for the ADC were taken from at91sam9260 dtsi but are not
correct.
Fixes: a4c1d6c75822 ("ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-10-alexandre.belloni@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f24479ead579459106bb55c2320a000135731f9 ]
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e1062fa7292f1e3744db0a487c4ac0109e09b03d ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: b7c2b61570798 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-4-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
