| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 450e7fe9b1b3c90eeed74a2fe0eeb13a7b57f3da ]
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0ef14bbb3 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c187e2eb3f92daa38cb3d4ab45e1107ea34108e ]
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a6d3 ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8c1efe14a4aadcfe93a158b1272e48298d2de15 ]
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693db6 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1605de1b3ca66e3eddbca4b3c353c13c26476fe2 ]
In case PM is enabled but there is no RAM controller information
in DT the code will panic. Avoid such scenarios by not initializing
platform specific PM code in case RAM controller is not provided
via DT.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 827de1f123ba0 ("ARM: at91: remove at91_dt_initialize and machine init_early()")
Fixes: 892e1f4a3ae58 ("ARM: at91: pm: add sama7g5 ddr phy controller")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-2-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f1db21c315f4b4f8c3fbea56aac500673132d317 ]
The 28NM DSI PLL driver for msm8960 calculates with a 27MHz reference
clock and should hence use PXO, not CXO which runs at 19.2MHz.
Note that none of the DSI PHY/PLL drivers currently use this "ref"
clock; they all rely on (sometimes inexistant) global clock names and
usually function normally without a parent clock. This discrepancy will
be corrected in a future patch, for which this change needs to be in
place first.
Fixes: 6969d1d9c615 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210829203027.276143-2-marijn.suijten@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f5c03f131dae3f06d08464e6157dd461200f78d9 upstream.
Also resolves these kernel warnings for APQ8064:
adreno 4300000.adreno-3xx: Using legacy qcom,chipid binding!
adreno 4300000.adreno-3xx: Use compatible qcom,adreno-320.2 instead.
Tested on Nexus 7 2013, no functional changes.
Cc: <stable@vger.kernel.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210818065317.19822-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b663b34c94a78f39fa2c7a8271b1f828b546e16 upstream.
Since the LED multicolor framework support was added in commit
92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd4c ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80d680fdccba214e8106dc1aa33de5207ad75394 upstream.
Nand is on CS1 so reg properties first field should be 1 not 0.
Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fa630bf473827aee48cbf0efbbdf6f03134e890 upstream
FTRACE_ADDR is only defined when CONFIG_DYNAMIC_FTRACE is defined, the
latter is even stronger requirement than CONFIG_FUNCTION_TRACER (which is
enough for MCOUNT_ADDR).
Link: https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/ZUVCQBHDMFVR7CCB7JPESLJEWERZDJ3T/
Fixes: 1f12fb25c5c5d22f ("ARM: 9079/1: ftrace: Add MODULE_PLTS support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79f32b221b18c15a98507b101ef4beb52444cc6f upstream
Teach ftrace_make_call() and ftrace_make_nop() about PLTs.
Teach PLT code about FTRACE and all its callbacks.
Otherwise the following might happen:
------------[ cut here ]------------
WARNING: CPU: 14 PID: 2265 at .../arch/arm/kernel/insn.c:14 __arm_gen_branch+0x83/0x8c()
...
Hardware name: LSI Axxia AXM55XX
[<c0314a49>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c0519f51>] (dump_stack+0x81/0xa8)
[<c0519f51>] (dump_stack) from [<c032185d>] (warn_slowpath_common+0x69/0x90)
[<c032185d>] (warn_slowpath_common) from [<c03218f3>] (warn_slowpath_null+0x17/0x1c)
[<c03218f3>] (warn_slowpath_null) from [<c03143cf>] (__arm_gen_branch+0x83/0x8c)
[<c03143cf>] (__arm_gen_branch) from [<c0314337>] (ftrace_make_nop+0xf/0x24)
[<c0314337>] (ftrace_make_nop) from [<c038ebcb>] (ftrace_process_locs+0x27b/0x3e8)
[<c038ebcb>] (ftrace_process_locs) from [<c0378d79>] (load_module+0x11e9/0x1a44)
[<c0378d79>] (load_module) from [<c037974d>] (SyS_finit_module+0x59/0x84)
[<c037974d>] (SyS_finit_module) from [<c030e981>] (ret_fast_syscall+0x1/0x18)
---[ end trace e1b64ced7a89adcc ]---
------------[ cut here ]------------
WARNING: CPU: 14 PID: 2265 at .../kernel/trace/ftrace.c:1979 ftrace_bug+0x1b1/0x234()
...
Hardware name: LSI Axxia AXM55XX
[<c0314a49>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c0519f51>] (dump_stack+0x81/0xa8)
[<c0519f51>] (dump_stack) from [<c032185d>] (warn_slowpath_common+0x69/0x90)
[<c032185d>] (warn_slowpath_common) from [<c03218f3>] (warn_slowpath_null+0x17/0x1c)
[<c03218f3>] (warn_slowpath_null) from [<c038e87d>] (ftrace_bug+0x1b1/0x234)
[<c038e87d>] (ftrace_bug) from [<c038ebd5>] (ftrace_process_locs+0x285/0x3e8)
[<c038ebd5>] (ftrace_process_locs) from [<c0378d79>] (load_module+0x11e9/0x1a44)
[<c0378d79>] (load_module) from [<c037974d>] (SyS_finit_module+0x59/0x84)
[<c037974d>] (SyS_finit_module) from [<c030e981>] (ret_fast_syscall+0x1/0x18)
---[ end trace e1b64ced7a89adcd ]---
ftrace failed to modify [<e9ef7006>] 0xe9ef7006
actual: 02:f0:3b:fa
ftrace record flags: 0
(0) expected tramp: c0314265
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 890cb057a46d323fd8c77ebecb6485476614cd21 upstream
Will be used in the following patch. No functional change.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e271701c17dee70c6e1351c4d7d42e70405c6a9 upstream upstream
No functional change, later it will be re-used in several files.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcf044891c84e38fc90eb736b818781bccf94e38 upstream.
We do not need a SWIOTLB unless we have DRAM that is addressable beyond
the arm_dma_limit. Compare max_pfn with arm_dma_pfn_limit to determine
whether we do need a SWIOTLB to be initialized.
Fixes: ad3c7b18c5b3 ("arm: use swiotlb for bounce buffering on LPAE configs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2270ad2f4e123336af685ecedd1618701cb4ca1e ]
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70e740ad55e5f93a19493720f4105555fade4a73 ]
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd7cd5b716d594e27a933c12f026d4f2426d7bf4 ]
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 818c4593434e81c9971b8fc278215121622c755e ]
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reported-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e6bc5987a5252948e3411e5a2dbb434fd1ea107 ]
Swap reg and reg-names order and drop adi,input-justification
and adi,input-style to fix the following dtbs_check warnings:
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly']
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]]
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected
arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8aec45d7884f16cc21d668693c5b88bff8df0f02 ]
Fix the following dtbs_check warning:
cs42l51@4a: port:endpoint@0:frame-master: True is not of type 'array'
cs42l51@4a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a79e78c391dc074742c855dc0108a88f781d56a3 ]
Fix the following dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:frame-master: True is not of type 'array'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:bitclock-master: True is not of type 'array'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0dc6c59892ead17a9febd11202c9f6794aac1895 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb1191 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b30d0289de72c62516df03fdad8d53f552c69839 upstream.
The merge_fdt_bootargs() function by definition consumes more than 1024
bytes of stack because it has a 1024 byte command line on the stack,
meaning that we always get a warning when building this file:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'merge_fdt_bootargs':
arch/arm/boot/compressed/atags_to_fdt.c:98:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
However, as this is the decompressor and we know that it has a very shallow
call chain, and we do not actually risk overflowing the kernel stack
at runtime here.
This just shuts up the warning by disabling the warning flag for this
file.
Tested on Nexus 7 2012 builds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf781869e5cf3e4ec1a47dad69b6f0df97629cbd upstream.
Add pinctrl-names and pinctrl-0 properties on controllers that claims to
use pins to avoid failures due to
commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges")
and also to avoid using pins that may be claimed my other IPs.
Fixes: b7c2b6157079 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210727074006.1609989-1-claudiu.beznea@microchip.com
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 72ccc373b064ae3ac0c5b5f2306069b60ca118df ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 087a1d8b4e4c ("ARM: dts: meson8b: ec100: add the VDDEE regulator")
Fixes: 3e7db1c1b7a3 ("ARM: dts: meson8b: ec100: improve the description of the regulators")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 632062e540becbbcb067523ec8bcadb1239d9578 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
Add missing pwm-supply for regulator-vcck regulator node.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: dee51cd0d2e8 ("ARM: dts: meson8b: mxq: add the VDDEE regulator")
Fixes: d94f60e3dfa0 ("ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-3-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 876228e9f935f19c7afc7ba394d17e2ec9143b65 ]
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply
instead of dummy regulator.
[ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree
[ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed
[ 7.117184] VCCK: supplied by regulator-dummy
[ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT
[ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled
[ 7.118498] VDDEE: will resolve supply early: pwm
[ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree
[ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed
[ 7.118553] VDDEE: supplied by regulator-dummy
[ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT
Fixes: 524d96083b66 ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator")
Fixes: 8bdf38be712d ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator")
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed typo in commit s/observer/observe/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44cf630bcb8c5ec78125805c9447dd5766792224 ]
We are seeing "imprecise external abort (0x1406)" errors during boot
(which then cause the whole board to hang) on Meson8 (but not Meson8m2).
These are observed while trying to access the GPU's registers when the
MALI clock is running at it's default setting of 24MHz. The 3.10 vendor
kernel uses 318.75MHz as "default" GPU frequency. Using that makes the
"imprecise external aborts" go away.
Add the assigned-clocks and assigned-clock-rates properties to also bump
the MALI clock to 318.75MHz before accessing any of it's registers.
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210711214023.2163565-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c295b7f3d01359ff4336fcb6e406e6ed37957d6 ]
The HVI3C shall be a group of I3C function, not an independent function.
Correct the function name from "HVI3C" to "I3C".
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Fixes: f510f04c8c83 ("ARM: dts: aspeed: Add AST2600 pinmux nodes")
Link: https://lore.kernel.org/r/20201029062723.20798-1-dylan_hung@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bae989c4bc53f861cc1b706aab0194703e9907a8 upstream.
The ams_delta_camera_power() function is unused as reports
Clang compilation with omap1_defconfig on linux-next:
arch/arm/mach-omap1/board-ams-delta.c:462:12: warning: unused function 'ams_delta_camera_power' [-Wunused-function]
static int ams_delta_camera_power(struct device *dev, int power)
^
1 warning generated.
The soc_camera support was dropped without removing
ams_delta_camera_power() function, making it unused.
Fixes: ce548396a433 ("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
Signed-off-by: Maciej Falkowski <maciej.falkowski9@gmail.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1326
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 47091f473b364c98207c4def197a0ae386fc9af1 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/ste-nomadik-nhk15.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@..
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210617210825.3064367-2-sudeep.holla@arm.com
Link: https://lore.kernel.org/r/20210626000103.830184-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20a6b3fd8e2e2c063b25fbf2ee74d86b898e5087 ]
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b070f9ca78680486927b799cf6126b128a7c2c1b upstream.
omap_hwmod_get_pwrdm() may access a NULL clk_hw pointer in some failure
cases. Add a check for the case and bail out gracely if this happens.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 15f68f027ebd961b99a1c420f96ff3838c5e4450 ]
While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36862c1ebc92a7e6fcc55002965c44b8ad17d4ca ]
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c68ef4ad180e09805fa46965d15e1dfadf09ffa5 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0162a9964365fd26e34575e121b17d021204c481 ]
Replace clock-name with clock-names.
Fixes: 2a4117df9b43 ("ARM: dts: Fix dcan driver probe failed on am437x platform")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d9e30a52047f2d464efdfd1d561ae1f707a0286 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb765d ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20fb73911fec01f06592de1cdbca00b66602ebd7 ]
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec8536580 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 828db68f4ff1ab6982a36a56522b585160dc8c8e ]
NXP and AzureWave don't recommend using SDIO bus mode 3.3V@50MHz due
to noise affecting the wireless throughput. Colibri iMX6ULL uses only
3.3V signaling for Wi-Fi module AW-CM276NF.
Limit the SDIO Clock on Colibri iMX6ULL to 25MHz.
Fixes: c2e4987e0e02 ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd8e83884fdd7b5fc411f201a58d8d01890198a2 ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf8085 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f07ec85365807b3939f32d0094a6dd5ce065d1b9 ]
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove and
error path.
Fixes: 9454a0caff6a ("ARM: imx: add mmdc ipg clock operation for mmdc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f9613aa07f16d6042e74208d1b40a6104d72964a ]
Commit e76bdfd7403a ("ARM: imx: Added perf functionality to mmdc driver")
introduced imx_mmdc_remove(), the mmdc_base need be unmapped in it if
config PERF_EVENTS is enabled.
If imx_mmdc_perf_init() fails, the mmdc_base also need be unmapped.
Fixes: e76bdfd7403a ("ARM: imx: Added perf functionality to mmdc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f5e81d1117501546b7be050c5fbafa6efd2c722c ]
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 82a1c67554dff610d6be4e1982c425717b3c6a23 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2d6608b57c50c54c3e46649110e8ea5a40959c30 upstream.
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Fixes: 2fc88f92359d ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: 961216c135a8 ("ARM: dts: aspeed: Add Rainier system")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca46ad2214473df1a6a9496be17156d65ba89b9f upstream.
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST250 |
