| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit f7daa9c8fd191724b9ab9580a7be55cd1a67d799 upstream.
During resume hibernate restores all physical memory. Any memory
that is accessed with the MMU disabled needs to be cleaned to the
PoC.
KVMs __hyp_text was previously ommitted as it runs with the MMU
enabled, but now that the hyp-stub is located in this section,
we must clean __hyp_text too.
This ensures secondary CPUs that come online after hibernate
has finished resuming, and load KVM via the freshly written
hyp-stub see the correct instructions.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fac5cbdfe0f01254d9d265c6aa1a95f94f58595 upstream.
The hyp-stub is loaded by the kernel's early startup code at EL2
during boot, before KVM takes ownership later. The hyp-stub's
text is part of the regular kernel text, meaning it can be kprobed.
A breakpoint in the hyp-stub causes the CPU to spin in el2_sync_invalid.
Add it to the __hyp_text.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8ea235932314311f15ea6cf65c1393ed7e31af70 upstream.
Commit 1598ecda7b23 ("arm64: kaslr: ensure randomized quantities are
clean to the PoC") added cache maintenance to ensure that global
variables set by the kaslr init routine are not wiped clean due to
cache invalidation occurring during the second round of page table
creation.
However, if kaslr_early_init() exits early with no randomization
being applied (either due to the lack of a seed, or because the user
has disabled kaslr explicitly), no cache maintenance is performed,
leading to the same issue we attempted to fix earlier, as far as the
module_alloc_base variable is concerned.
Note that module_alloc_base cannot be initialized statically, because
that would cause it to be subject to a R_AARCH64_RELATIVE relocation,
causing it to be overwritten by the second round of KASLR relocation
processing.
Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65dbb423cf28232fed1732b779249d6164c5999b upstream.
Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.
Commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing to the wrong
registers.
For instance, upon ath9k module loading:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
(CACHE_LINE_SIZE)
Fix the bug by removing the alignment in the cns3xxx mapping function.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 867cefb4cb1012f42cada1c7d1f35ac8dd276071 upstream.
Commit f94c8d11699759 ("sched/clock, x86/tsc: Rework the x86 'unstable'
sched_clock() interface") broke Xen guest time handling across
migration:
[ 187.249951] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 187.251137] OOM killer disabled.
[ 187.251137] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 187.252299] suspending xenstore...
[ 187.266987] xen:grant_table: Grant tables using version 1 layout
[18446743811.706476] OOM killer enabled.
[18446743811.706478] Restarting tasks ... done.
[18446743811.720505] Setting capacity to 16777216
Fix that by setting xen_sched_clock_offset at resume time to ensure a
monotonic clock value.
[boris: replaced pr_info() with pr_info_once() in xen_callback_vector()
to avoid printing with incorrect timestamp during resume (as we
haven't re-adjusted the clock yet)]
Fixes: f94c8d11699759 ("sched/clock, x86/tsc: Rework the x86 'unstable' sched_clock() interface")
Cc: <stable@vger.kernel.org> # 4.11
Reported-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38669ba205d178d2d38bfd194a196d65a44d5af2 upstream.
It is expected for sched_clock() to output data from 0, when system boots.
Add an offset xen_sched_clock_offset (similarly how it is done in other
hypervisors i.e. kvm_sched_clock_offset) to count sched_clock() from 0,
when time is first initialized.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: steven.sistare@oracle.com
Cc: daniel.m.jordan@oracle.com
Cc: linux@armlinux.org.uk
Cc: schwidefsky@de.ibm.com
Cc: heiko.carstens@de.ibm.com
Cc: john.stultz@linaro.org
Cc: sboyd@codeaurora.org
Cc: hpa@zytor.com
Cc: douly.fnst@cn.fujitsu.com
Cc: peterz@infradead.org
Cc: prarit@redhat.com
Cc: feng.tang@intel.com
Cc: pmladek@suse.com
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: linux-s390@vger.kernel.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: pbonzini@redhat.com
Link: https://lkml.kernel.org/r/20180719205545.16512-14-pasha.tatashin@oracle.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2229f70b5bbb025e1394b61007938a68060afbfb upstream.
In order to support pvclock vdso on xen we need to setup the time
info page for vcpu 0 and register the page with Xen using the
VCPUOP_register_vcpu_time_memory_area hypercall. This hypercall
will also forcefully update the pvti which will set some of the
necessary flags for vdso. Afterwards we check if it supports the
PVCLOCK_TSC_STABLE_BIT flag which is mandatory for having
vdso/vsyscall support. And if so, it will set the cpu 0 pvti that
will be later on used when mapping the vdso image.
The xen headers are also updated to include the new hypercall for
registering the secondary vcpu_time_info struct.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b888808093113ae7d63d213272d01fea4b8329ed upstream.
Specifically check for PVCLOCK_TSC_STABLE_BIT and if this bit is set,
then set it too on pvclock flags. This allows Xen clocksource to use it
and thus speeding up xen_clocksource_read() callers (i.e. sched_clock())
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f08890ab906abaf9d4c1bad8111755cbd302260 upstream.
Right now there is only a pvclock_pvti_cpu0_va() which is defined
on kvmclock since:
commit dac16fba6fc5
("x86/vdso: Get pvclock data from the vvar VMA instead of the fixmap")
The only user of this interface so far is kvm. This commit adds a
setter function for the pvti page and moves pvclock_pvti_cpu0_va
to pvclock, which is a more generic place to have it; and would
allow other PV clocksources to use it, such as Xen.
While moving pvclock_pvti_cpu0_va into pvclock, rename also this
function to pvclock_get_pvti_cpu0_va (including its call sites)
to be symmetric with the setter (pvclock_set_pvti_cpu0_va).
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60f1bf29c0b2519989927cae640cd1f50f59dc7f upstream.
When calling smp_call_ipl_cpu() from the IPL CPU, we will try to read
from pcpu_devices->lowcore. However, due to prefixing, that will result
in reading from absolute address 0 on that CPU. We have to go via the
actual lowcore instead.
This means that right now, we will read lc->nodat_stack == 0 and
therfore work on a very wrong stack.
This BUG essentially broke rebooting under QEMU TCG (which will report
a low address protection exception). And checking under KVM, it is
also broken under KVM. With 1 VCPU it can be easily triggered.
:/# echo 1 > /proc/sys/kernel/sysrq
:/# echo b > /proc/sysrq-trigger
[ 28.476745] sysrq: SysRq : Resetting
[ 28.476793] Kernel stack overflow.
[ 28.476817] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476820] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476826] Krnl PSW : 0400c00180000000 0000000000115c0c (pcpu_delegate+0x12c/0x140)
[ 28.476861] R:0 T:1 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[ 28.476863] Krnl GPRS: ffffffffffffffff 0000000000000000 000000000010dff8 0000000000000000
[ 28.476864] 0000000000000000 0000000000000000 0000000000ab7090 000003e0006efbf0
[ 28.476864] 000000000010dff8 0000000000000000 0000000000000000 0000000000000000
[ 28.476865] 000000007fffc000 0000000000730408 000003e0006efc58 0000000000000000
[ 28.476887] Krnl Code: 0000000000115bfe: 4170f000 la %r7,0(%r15)
[ 28.476887] 0000000000115c02: 41f0a000 la %r15,0(%r10)
[ 28.476887] #0000000000115c06: e370f0980024 stg %r7,152(%r15)
[ 28.476887] >0000000000115c0c: c0e5fffff86e brasl %r14,114ce8
[ 28.476887] 0000000000115c12: 41f07000 la %r15,0(%r7)
[ 28.476887] 0000000000115c16: a7f4ffa8 brc 15,115b66
[ 28.476887] 0000000000115c1a: 0707 bcr 0,%r7
[ 28.476887] 0000000000115c1c: 0707 bcr 0,%r7
[ 28.476901] Call Trace:
[ 28.476902] Last Breaking-Event-Address:
[ 28.476920] [<0000000000a01c4a>] arch_call_rest_init+0x22/0x80
[ 28.476927] Kernel panic - not syncing: Corrupt kernel stack, can't continue.
[ 28.476930] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476932] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476932] Call Trace:
Fixes: 2f859d0dad81 ("s390/smp: reduce size of struct pcpu")
Cc: stable@vger.kernel.org # 4.0+
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upstream commit:
f775b13eedee ("x86,kvm: move qemu/guest FPU switching out to vcpu_run")
introduced a bug, which was later fixed by upstream commit:
5663d8f9bbe4 ("kvm: x86: fix WARN due to uninitialized guest FPU state")
For reasons unknown, both commits were initially passed-over for
inclusion in the 4.14 stable branch despite being tagged for stable.
Eventually, someone noticed that the fixup, commit 5663d8f9bbe4, was
missing from stable[1], and so it was queued up for 4.14 and included in
release v4.14.79.
Even later, the original buggy patch, commit f775b13eedee, was also
applied to the 4.14 stable branch. Through an unlucky coincidence, the
incorrect ordering did not generate a conflict between the two patches,
and led to v4.14.94 and later releases containing a spurious call to
kvm_load_guest_fpu() in kvm_arch_vcpu_ioctl_run(). As a result, KVM may
reload stale guest FPU state, e.g. after accepting in INIT event. This
can manifest as crashes during boot, segfaults, failed checksums and so
on and so forth.
Remove the unwanted kvm_{load,put}_guest_fpu() calls, i.e. make
kvm_arch_vcpu_ioctl_run() look like commit 5663d8f9bbe4 was backported
after commit f775b13eedee.
[1] https://www.spinics.net/lists/stable/msg263931.html
Fixes: 4124a4cff344 ("x86,kvm: move qemu/guest FPU switching out to vcpu_run")
Cc: stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Reported-by: Roman Mamedov
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e6fc2f50a3197d0e82d1c0e86282976c9e6c8a4 upstream.
The outb() function takes parameters value and port, in that order. Fix
the parameters used in the kalsr i8254 fallback code.
Fixes: 5bfce5ef55cb ("x86, kaslr: Provide randomness functions")
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: linux@endlessm.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190107034024.15005-1-drake@endlessm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a31e184e4f69965c99c04cc5eb8a4920e0c63737 upstream.
Memory protection key behavior should be the same in a child as it was
in the parent before a fork. But, there is a bug that resets the
state in the child at fork instead of preserving it.
The creation of new mm's is a bit convoluted. At fork(), the code
does:
1. memcpy() the parent mm to initialize child
2. mm_init() to initalize some select stuff stuff
3. dup_mmap() to create true copies that memcpy() did not do right
For pkeys two bits of state need to be preserved across a fork:
'execute_only_pkey' and 'pkey_allocation_map'.
Those are preserved by the memcpy(), but mm_init() invokes
init_new_context() which overwrites 'execute_only_pkey' and
'pkey_allocation_map' with "new" values.
The author of the code erroneously believed that init_new_context is *only*
called at execve()-time. But, alas, init_new_context() is used at execve()
and fork().
The result is that, after a fork(), the child's pkey state ends up looking
like it does after an execve(), which is totally wrong. pkeys that are
already allocated can be allocated again, for instance.
To fix this, add code called by dup_mmap() to copy the pkey state from
parent to child explicitly. Also add a comment above init_new_context() to
make it more clear to the next poor sod what this code is used for.
Fixes: e8c24d3a23a ("x86/pkeys: Allocation/free syscalls")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: peterz@infradead.org
Cc: mpe@ellerman.id.au
Cc: will.deacon@arm.com
Cc: luto@kernel.org
Cc: jroedel@suse.de
Cc: stable@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20190102215655.7A69518C@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5cc244a20b86090c087073c124284381cdf47234 upstream.
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7cb707c373094ce4008d4a6ac9b6b366ec52da5 upstream.
smp_rescan_cpus() is called without the device_hotplug_lock, which can lead
to a dedlock when a new CPU is found and immediately set online by a udev
rule.
This was observed on an older kernel version, where the cpu_hotplug_begin()
loop was still present, and it resulted in hanging chcpu and systemd-udev
processes. This specific deadlock will not show on current kernels. However,
there may be other possible deadlocks, and since smp_rescan_cpus() can still
trigger a CPU hotplug operation, the device_hotplug_lock should be held.
For reference, this was the deadlock with the old cpu_hotplug_begin() loop:
chcpu (rescan) systemd-udevd
echo 1 > /sys/../rescan
-> smp_rescan_cpus()
-> (*) get_online_cpus()
(increases refcount)
-> smp_add_present_cpu()
(new CPU found)
-> register_cpu()
-> device_add()
-> udev "add" event triggered -----------> udev rule sets CPU online
-> echo 1 > /sys/.../online
-> lock_device_hotplug_sysfs()
(this is missing in rescan path)
-> device_online()
-> (**) device_lock(new CPU dev)
-> cpu_up()
-> cpu_hotplug_begin()
(loops until refcount == 0)
-> deadlock with (*)
-> bus_probe_device()
-> device_attach()
-> device_lock(new CPU dev)
-> deadlock with (**)
Fix this by taking the device_hotplug_lock in the CPU rescan path.
Cc: <stable@vger.kernel.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03aa047ef2db4985e444af6ee1c1dd084ad9fb4c upstream.
Right now the early machine detection code check stsi 3.2.2 for "KVM"
and set MACHINE_IS_VM if this is different. As the console detection
uses diagnose 8 if MACHINE_IS_VM returns true this will crash Linux
early for any non z/VM system that sets a different value than KVM.
So instead of assuming z/VM, do not set any of MACHINE_IS_LPAR,
MACHINE_IS_VM, or MACHINE_IS_KVM.
CC: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3affbf0e154ee351add6fcc254c59c3f3947fa8f upstream.
So far we've mapped branches to "ijmp" which also counts conditional
branches NOT taken. This makes us different from other architectures
such as ARM which seem to be counting only taken branches.
So use "ijmptak" hardware condition which only counts (all jump
instructions that are taken)
'ijmptak' event is available on both ARCompact and ARCv2 ISA based
cores.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked changelog]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3010a0465383300f909f62b8a83f83ffa7b2517 upstream.
In setup_arch_memory we reserve the memory area wherein the kernel
is located. Current implementation may reserve more memory than
it actually required in case of CONFIG_LINUX_LINK_BASE is not
equal to CONFIG_LINUX_RAM_BASE. This happens because we calculate
start of the reserved region relatively to the CONFIG_LINUX_RAM_BASE
and end of the region relatively to the CONFIG_LINUX_RAM_BASE.
For example in case of HSDK board we wasted 256MiB of physical memory:
------------------->8------------------------------
Memory: 770416K/1048576K available (5496K kernel code,
240K rwdata, 1064K rodata, 2200K init, 275K bss,
278160K reserved, 0K cma-reserved)
------------------->8------------------------------
Fix that.
Fixes: 9ed68785f7f2b ("ARC: mm: Decouple RAM base address from kernel link addr")
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6a72b7daeeb521753803550f0ed711152bb2555 upstream.
ARCv2 optimized memset uses PREFETCHW instruction for prefetching the
next cache line but doesn't ensure that the line is not past the end of
the buffer. PRETECHW changes the line ownership and marks it dirty,
which can cause issues in SMP config when next line was already owned by
other core. Fix the issue by avoiding the PREFETCHW
Some more details:
The current code has 3 logical loops (ignroing the unaligned part)
(a) Big loop for doing aligned 64 bytes per iteration with PREALLOC
(b) Loop for 32 x 2 bytes with PREFETCHW
(c) any left over bytes
loop (a) was already eliding the last 64 bytes, so PREALLOC was
safe. The fix was removing PREFETCW from (b).
Another potential issue (applicable to configs with 32 or 128 byte L1
cache line) is that PREALLOC assumes 64 byte cache line and may not do
the right thing specially for 32b. While it would be easy to adapt,
there are no known configs with those lie sizes, so for now, just
compile out PREALLOC in such cases.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: stable@vger.kernel.org #4.4+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog, used asm .macro vs. "C" macro]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 33309ecda0070506c49182530abe7728850ebe78 ]
The dcache_by_line_op macro suffers from a couple of small problems:
First, the GAS directives that are currently being used rely on
assembler behavior that is not documented, and probably not guaranteed
to produce the correct behavior going forward. As a result, we end up
with some undefined symbols in cache.o:
$ nm arch/arm64/mm/cache.o
...
U civac
...
U cvac
U cvap
U cvau
This is due to the fact that the comparisons used to select the
operation type in the dcache_by_line_op macro are comparing symbols
not strings, and even though it seems that GAS is doing the right
thing here (undefined symbols by the same name are equal to each
other), it seems unwise to rely on this.
Second, when patching in a DC CVAP instruction on CPUs that support it,
the fallback path consists of a DC CVAU instruction which may be
affected by CPU errata that require ARM64_WORKAROUND_CLEAN_CACHE.
Solve these issues by unrolling the various maintenance routines and
using the conditional directives that are documented as operating on
strings. To avoid the complexity of nested alternatives, we move the
DC CVAP patching to __clean_dcache_area_pop, falling back to a branch
to __clean_dcache_area_poc if DCPOP is not supported by the CPU.
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d4a862276a9c30a269d368d324fb56529e6d5fd ]
Currently xmon needs to get devtree_lock (through rtas_token()) during its
invocation (at crash time). If there is a crash while devtree_lock is being
held, then xmon tries to get the lock but spins forever and never get into
the interactive debugger, as in the following case:
int *ptr = NULL;
raw_spin_lock_irqsave(&devtree_lock, flags);
*ptr = 0xdeadbeef;
This patch avoids calling rtas_token(), thus trying to get the same lock,
at crash time. This new mechanism proposes getting the token at
initialization time (xmon_init()) and just consuming it at crash time.
This would allow xmon to be possible invoked independent of devtree_lock
being held or not.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 81e9fa8bab381f8b6eb04df7cdf0f71994099bd4 ]
The armv8_pmuv3 driver doesn't have a remove function, and when the test
'CONFIG_DEBUG_TEST_DRIVER_REMOVE=y' is enabled, the following Call trace
can be seen.
[ 1.424287] Failed to register pmu: armv8_pmuv3, reason -17
[ 1.424870] WARNING: CPU: 0 PID: 1 at ../kernel/events/core.c:11771 perf_event_sysfs_init+0x98/0xdc
[ 1.425220] Modules linked in:
[ 1.425531] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.19.0-rc7-next-20181012-00003-ge7a97b1ad77b-dirty #35
[ 1.425951] Hardware name: linux,dummy-virt (DT)
[ 1.426212] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 1.426458] pc : perf_event_sysfs_init+0x98/0xdc
[ 1.426720] lr : perf_event_sysfs_init+0x98/0xdc
[ 1.426908] sp : ffff00000804bd50
[ 1.427077] x29: ffff00000804bd50 x28: ffff00000934e078
[ 1.427429] x27: ffff000009546000 x26: 0000000000000007
[ 1.427757] x25: ffff000009280710 x24: 00000000ffffffef
[ 1.428086] x23: ffff000009408000 x22: 0000000000000000
[ 1.428415] x21: ffff000009136008 x20: ffff000009408730
[ 1.428744] x19: ffff80007b20b400 x18: 000000000000000a
[ 1.429075] x17: 0000000000000000 x16: 0000000000000000
[ 1.429418] x15: 0000000000000400 x14: 2e79726f74636572
[ 1.429748] x13: 696420656d617320 x12: 656874206e692065
[ 1.430060] x11: 6d616e20656d6173 x10: 2065687420687469
[ 1.430335] x9 : ffff00000804bd50 x8 : 206e6f7361657220
[ 1.430610] x7 : 2c3376756d705f38 x6 : ffff00000954d7ce
[ 1.430880] x5 : 0000000000000000 x4 : 0000000000000000
[ 1.431226] x3 : 0000000000000000 x2 : ffffffffffffffff
[ 1.431554] x1 : 4d151327adc50b00 x0 : 0000000000000000
[ 1.431868] Call trace:
[ 1.432102] perf_event_sysfs_init+0x98/0xdc
[ 1.432382] do_one_initcall+0x6c/0x1a8
[ 1.432637] kernel_init_freeable+0x1bc/0x280
[ 1.432905] kernel_init+0x18/0x160
[ 1.433115] ret_from_fork+0x10/0x18
[ 1.433297] ---[ end trace 27fd415390eb9883 ]---
Rework to set suppress_bind_attrs flag to avoid removing the device when
CONFIG_DEBUG_TEST_DRIVER_REMOVE=y, since there's no real reason to
remove the armv8_pmuv3 driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e4849aff1e169b86c561738daf8ff020e9de1011 ]
The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip
DRAM controller that supports memory amounts of up to 16GiB, and due to
how the address decoder has been wired in the SOC any memory beyond 1GiB
is actually mapped starting from 4GiB physical up, that is beyond the
32-bit addressable limit[1]. Consequently if the maximum amount of
memory has been installed, then it will span up to 19GiB.
Many of the evaluation boards we support that are based on one of these
SOCs have their memory soldered and the amount present fits in the
32-bit address range. The BCM91250A SWARM board however has actual DIMM
slots and accepts, depending on the peripherals revision of the SOC, up
to 4GiB or 8GiB of memory in commercially available JEDEC modules[2].
I believe this is also the case with the BCM91250C2 LittleSur board.
This means that up to either 3GiB or 7GiB of memory requires 64-bit
addressing to access.
I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead,
accepts at least as much memory, although I have no documentation or
actual hardware available to verify that.
Both systems have PCI slots installed for use by any PCI option boards,
including ones that only support 32-bit addressing (additionally the
32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits
addressing to 32-bits), and there is no IOMMU available. Therefore for
PCI DMA to work in the presence of memory beyond enable swiotlb for the
affected systems.
All the other SOC onchip DMA devices use 40-bit addressing and therefore
can address the whole memory, so only enable swiotlb if PCI support and
support for DMA beyond 4GiB have been both enabled in the configuration
of the kernel.
This shows up as follows:
Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2)
Board type: SiByte BCM91250A (SWARM)
Determined physical RAM map:
memory: 000000000fe7fe00 @ 0000000000000000 (usable)
memory: 000000001ffffe00 @ 0000000080000000 (usable)
memory: 000000000ffffe00 @ 00000000c0000000 (usable)
memory: 0000000087fffe00 @ 0000000100000000 (usable)
software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB)
in the bootstrap log and removes failures like these:
defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi0: Receive buffer allocation failed
fddi0: Adapter open failed!
IP-Config: Failed to open fddi0
defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi1: Receive buffer allocation failed
fddi1: Adapter open failed!
IP-Config: Failed to open fddi1
when memory beyond 4GiB is handed out to devices that can only do 32-bit
addressing.
This updates commit cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need
DMA32.").
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
[2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom
Corporation, 18 May 2004, Section 3: "Physical Description",
"Supported DRAM", p. 23
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21108/
References: cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68b5e4326e4b8ac9080835005d8254fed0fb3c56 ]
Add the proper includes and make smca_get_name() static.
Fix an actual bug too which the warning triggered:
arch/x86/kernel/cpu/mcheck/therm_throt.c:395:39: error: conflicting \
types for ‘smp_thermal_interrupt’
asmlinkage __visible void __irq_entry smp_thermal_interrupt(struct pt_regs *r)
^~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/kernel/cpu/mcheck/therm_throt.c:29:
./arch/x86/include/asm/traps.h:107:17: note: previous declaration of \
‘smp_thermal_interrupt’ was here
asmlinkage void smp_thermal_interrupt(void);
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yi Wang <wang.yi59@zte.com.cn>
Cc: Michael Matz <matz@suse.de>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1811081633160.1549@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a214720cbf50cd8c3f76bbb9c3f5c283910e9d33 upstream.
Octeon has an boot-time option to disable pcie.
Since MSI depends on PCI-E, we should also disable MSI also with
this option is on in order to avoid inadvertently accessing PCIe
registers.
Signed-off-by: YunQiang Su <ysu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: pburton@wavecomp.com
Cc: linux-mips@vger.kernel.org
Cc: aaro.koskinen@iki.fi
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1598ecda7b239e9232dda032bfddeed9d89fab6c upstream.
kaslr_early_init() is called with the kernel mapped at its
link time offset, and if it returns with a non-zero offset,
the kernel is unmapped and remapped again at the randomized
offset.
During its execution, kaslr_early_init() also randomizes the
base of the module region and of the linear mapping of DRAM,
and sets two variables accordingly. However, since these
variables are assigned with the caches on, they may get lost
during the cache maintenance that occurs when unmapping and
remapping the kernel, so ensure that these values are cleaned
to the PoC.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b4dba55b04b212a7fd1f0395b41d79ee3a9801b upstream.
This makes SMP on the vrx200 work again, by removing all the MIPS CPU
interrupt specific code and making it fully use the generic MIPS CPU
interrupt controller.
The mti,cpu-interrupt-controller from irq-mips-cpu.c now handles the CPU
interrupts and also the IPI interrupts which are used to communication
between the CPUs in a SMP system. The generic interrupt code was
already used before but the interrupt vectors were overwritten again
when we called set_vi_handler() in the lantiq interrupt driver and we
also provided our own plat_irq_dispatch() function which overwrote the
weak generic implementation. Now the code uses the generic handler for
the MIPS CPU interrupts including the IPI interrupts and registers a
handler for the CPU interrupts which are handled by the lantiq ICU with
irq_set_chained_handler() which was already called before.
Calling the set_c0_status() function is also not needed any more because
the generic MIPS CPU interrupt already activates the needed bits.
Fixes: 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support")
Cc: stable@kernel.org # v4.12
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: jhogan@kernel.org
Cc: ralf@linux-mips.org
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a9372f751b5350e0ce3d2ee91832f1feae2c2e5 upstream.
While reading through the sysvipc implementation, I noticed that the n32
semctl/shmctl/msgctl system calls behave differently based on whether
o32 support is enabled or not: Without o32, the IPC_64 flag passed by
user space is rejected but calls without that flag get IPC_64 behavior.
As far as I can tell, this was inadvertently changed by a cleanup patch
but never noticed by anyone, possibly nobody has tried using sysvipc
on n32 after linux-3.19.
Change it back to the old behavior now.
Fixes: 78aaf956ba3a ("MIPS: Compat: Fix build error if CONFIG_MIPS32_COMPAT but no compat ABI.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Backport of upstream commit b3669b1e1c09890d61109a1a8ece2c5b66804714 ]
To allow EL0 (and/or EL1) to use pointer authentication functionality,
we must ensure that pointer authentication instructions and accesses to
pointer authentication keys are not trapped to EL2.
This patch ensures that HCR_EL2 is configured appropriately when the
kernel is booted at EL2. For non-VHE kernels we set HCR_EL2.{API,APK},
ensuring that EL1 can access keys and permit EL0 use of instructions.
For VHE kernels host EL0 (TGE && E2H) is unaffected by these settings,
and it doesn't matter how we configure HCR_EL2.{API,APK}, so we don't
bother setting them.
This does not enable support for KVM guests, since KVM manages HCR_EL2
itself when running VMs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
[kristina: backport to 4.14.y: adjust context]
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Backport of upstream commit 4eaed6aa2c628101246bcabc91b203bfac1193f8 ]
In KVM we define the configuration of HCR_EL2 for a VHE HOST in
HCR_HOST_VHE_FLAGS, but we don't have a similar definition for the
non-VHE host flags, and open-code HCR_RW. Further, in head.S we
open-code the flags for VHE and non-VHE configurations.
In future, we're going to want to configure more flags for the host, so
lets add a HCR_HOST_NVHE_FLAGS defintion, and consistently use both
HCR_HOST_VHE_FLAGS and HCR_HOST_NVHE_FLAGS in the kvm code and head.S.
We now use mov_q to generate the HCR_EL2 value, as we use when
configuring other registers in head.S.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
[kristina: backport to 4.14.y: adjust context]
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e4f358916d528d479c3c12bd2fd03f2d5a576380 upstream.
Commit
4cd24de3a098 ("x86/retpoline: Make CONFIG_RETPOLINE depend on compiler support")
replaced the RETPOLINE define with CONFIG_RETPOLINE checks. Remove the
remaining pieces.
[ bp: Massage commit message. ]
Fixes: 4cd24de3a098 ("x86/retpoline: Make CONFIG_RETPOLINE depend on compiler support")
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: linux-kbuild@vger.kernel.org
Cc: srinivas.eeda@oracle.com
Cc: stable <stable@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181210163725.95977-1-chao.wang@ucloud.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f775b13eedee2f7f3c6fdd4e90fb79090ce5d339 upstream.
Currently, every time a VCPU is scheduled out, the host kernel will
first save the guest FPU/xstate context, then load the qemu userspace
FPU context, only to then immediately save the qemu userspace FPU
context back to memory. When scheduling in a VCPU, the same extraneous
FPU loads and saves are done.
This could be avoided by moving from a model where the guest FPU is
loaded and stored with preemption disabled, to a model where the
qemu userspace FPU is swapped out for the guest FPU context for
the duration of the KVM_RUN ioctl.
This is done under the VCPU mutex, which is also taken when other
tasks inspect the VCPU FPU context, so the code should already be
safe for this change. That should come as no surprise, given that
s390 already has this optimization.
This can fix a bug where KVM calls get_user_pages while owning the
FPU, and the file system ends up requesting the FPU again:
[258270.527947] __warn+0xcb/0xf0
[258270.527948] warn_slowpath_null+0x1d/0x20
[258270.527951] kernel_fpu_disable+0x3f/0x50
[258270.527953] __kernel_fpu_begin+0x49/0x100
[258270.527955] kernel_fpu_begin+0xe/0x10
[258270.527958] crc32c_pcl_intel_update+0x84/0xb0
[258270.527961] crypto_shash_update+0x3f/0x110
[258270.527968] crc32c+0x63/0x8a [libcrc32c]
[258270.527975] dm_bm_checksum+0x1b/0x20 [dm_persistent_data]
[258270.527978] node_prepare_for_write+0x44/0x70 [dm_persistent_data]
[258270.527985] dm_block_manager_write_callback+0x41/0x50 [dm_persistent_data]
[258270.527988] submit_io+0x170/0x1b0 [dm_bufio]
[258270.527992] __write_dirty_buffer+0x89/0x90 [dm_bufio]
[258270.527994] __make_buffer_clean+0x4f/0x80 [dm_bufio]
[258270.527996] __try_evict_buffer+0x42/0x60 [dm_bufio]
[258270.527998] dm_bufio_shrink_scan+0xc0/0x130 [dm_bufio]
[258270.528002] shrink_slab.part.40+0x1f5/0x420
[258270.528004] shrink_node+0x22c/0x320
[258270.528006] do_try_to_free_pages+0xf5/0x330
[258270.528008] try_to_free_pages+0xe9/0x190
[258270.528009] __alloc_pages_slowpath+0x40f/0xba0
[258270.528011] __alloc_pages_nodemask+0x209/0x260
[258270.528014] alloc_pages_vma+0x1f1/0x250
[258270.528017] do_huge_pmd_anonymous_page+0x123/0x660
[258270.528021] handle_mm_fault+0xfd3/0x1330
[258270.528025] __get_user_pages+0x113/0x640
[258270.528027] get_user_pages+0x4f/0x60
[258270.528063] __gfn_to_pfn_memslot+0x120/0x3f0 [kvm]
[258270.528108] try_async_pf+0x66/0x230 [kvm]
[258270.528135] tdp_page_fault+0x130/0x280 [kvm]
[258270.528149] kvm_mmu_page_fault+0x60/0x120 [kvm]
[258270.528158] handle_ept_violation+0x91/0x170 [kvm_intel]
[258270.528162] vmx_handle_exit+0x1ca/0x1400 [kvm_intel]
No performance changes were detected in quick ping-pong tests on
my 4 socket system, which is expected since an FPU+xstate load is
on the order of 0.1us, while ping-ponging between CPUs is on the
order of 20us, and somewhat noisy.
Cc: stable@vger.kernel.org
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Fixed a bug where reset_vcpu called put_fpu without preceding load_fpu,
which happened inside from KVM_CREATE_VCPU ioctl. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1c3743e1a20647c53b719dbf28b48f45d23f2cd upstream.
On a signal handler return, the user could set a context with MSR[TS] bits
set, and these bits would be copied to task regs->msr.
At restore_tm_sigcontexts(), after current task regs->msr[TS] bits are set,
several __get_user() are called and then a recheckpoint is executed.
This is a problem since a page fault (in kernel space) could happen when
calling __get_user(). If it happens, the process MSR[TS] bits were
already set, but recheckpoint was not executed, and SPRs are still invalid.
The page fault can cause the current process to be de-scheduled, with
MSR[TS] active and without tm_recheckpoint() being called. More
importantly, |
