| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 252714f1e8bdd542025b16321c790458014d6880 ]
This reverts commit 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in
btusb.c file").
In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This
ties the lifetime of all the btusb data to the binding of a driver to
one interface, INTF. In a driver that binds to other interfaces, ISOC
and DIAG, this is an accident waiting to happen.
The issue is revealed in btusb_disconnect(), where calling
usb_driver_release_interface(&btusb_driver, data->intf) will have devm
free the data that is also being used by the other interfaces of the
driver that may not be released yet.
To fix this, revert the use of devm and go back to freeing memory
explicitly.
Fixes: 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 32caa197b9b603e20f49fd3a0dffecd0cd620499 ]
Add the support ID(0x0489, 0xE12F) to usb_device_id table for
Realtek RTL8852BE-VT.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e12f Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 525459da4bd62a81142fea3f3d52188ceb4d8907 ]
Add VID 13d3 & PID 3533 for Realtek RTL8821CE USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3533 Rev= 1.10
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Gongwei Li <ligongwei@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8b38d19857d42a1f2e90c9d9b0f74de2500acd7 ]
The new platform uses the QCA2066 chip along with a new board ID, which
requires a dedicated firmware file to ensure proper initialization.
Without this entry, the driver cannot locate and load the correct
firmware, resulting in Bluetooth bring-up failure.
This patch adds a new entry to the firmware table for QCA2066 so that
the driver can correctly identify the board ID and load the appropriate
firmware from 'qca/QCA2066/' in the linux-firmware repository.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c126f98c011f5796ba118ef2093122d02809d30d ]
Add VID 0489 & PID e135 for MediaTek MT7920 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e135 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a6700a31c953af9a17a7e2681335f31d922614d ]
Add VID 0489 & PID e170 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e170 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8dbbb5423c0802ec21266765de80fd491868fab1 ]
Add VID 2b89 & PID 6275 for Realtek RTL8761BUV USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2b89 ProdID=6275 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00E04C239987
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Chingbin Li <liqb365@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to:
usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM)
That function can return NULL in some cases. Even when it returns
NULL, though, we still go on to call btusb_mtk_claim_iso_intf().
As of commit e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for
usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf()
when `btmtk_data->isopkt_intf` is NULL will cause a crash because
we'll end up passing a bad pointer to device_lock(). Prior to that
commit we'd pass the NULL pointer directly to
usb_driver_claim_interface() which would detect it and return an
error, which was handled.
Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check
at the start of the function. This makes the code handle a NULL
`btmtk_data->isopkt_intf` the same way it did before the problematic
commit (just with a slight change to the error message printed).
Reported-by: IncogCyberpunk <incogcyberpunk@proton.me>
Closes: http://lore.kernel.org/r/a380d061-479e-4713-bddd-1d6571ca7e86@leemhuis.info
Fixes: e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()")
Cc: stable@vger.kernel.org
Tested-by: IncogCyberpunk <incogcyberpunk@proton.me>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When performing reset tests and encountering abnormal card drop issues
that lead to a kernel crash, it is necessary to perform a null check
before releasing resources to avoid attempting to release a null pointer.
<4>[ 29.158070] Hardware name: Google Quigon sku196612/196613 board (DT)
<4>[ 29.158076] Workqueue: hci0 hci_cmd_sync_work [bluetooth]
<4>[ 29.158154] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
<4>[ 29.158162] pc : klist_remove+0x90/0x158
<4>[ 29.158174] lr : klist_remove+0x88/0x158
<4>[ 29.158180] sp : ffffffc0846b3c00
<4>[ 29.158185] pmr_save: 000000e0
<4>[ 29.158188] x29: ffffffc0846b3c30 x28: ffffff80cd31f880 x27: ffffff80c1bdc058
<4>[ 29.158199] x26: dead000000000100 x25: ffffffdbdc624ea3 x24: ffffff80c1bdc4c0
<4>[ 29.158209] x23: ffffffdbdc62a3e6 x22: ffffff80c6c07000 x21: ffffffdbdc829290
<4>[ 29.158219] x20: 0000000000000000 x19: ffffff80cd3e0648 x18: 000000031ec97781
<4>[ 29.158229] x17: ffffff80c1bdc4a8 x16: ffffffdc10576548 x15: ffffff80c1180428
<4>[ 29.158238] x14: 0000000000000000 x13: 000000000000e380 x12: 0000000000000018
<4>[ 29.158248] x11: ffffff80c2a7fd10 x10: 0000000000000000 x9 : 0000000100000000
<4>[ 29.158257] x8 : 0000000000000000 x7 : 7f7f7f7f7f7f7f7f x6 : 2d7223ff6364626d
<4>[ 29.158266] x5 : 0000008000000000 x4 : 0000000000000020 x3 : 2e7325006465636e
<4>[ 29.158275] x2 : ffffffdc11afeff8 x1 : 0000000000000000 x0 : ffffffdc11be4d0c
<4>[ 29.158285] Call trace:
<4>[ 29.158290] klist_remove+0x90/0x158
<4>[ 29.158298] device_release_driver_internal+0x20c/0x268
<4>[ 29.158308] device_release_driver+0x1c/0x30
<4>[ 29.158316] usb_driver_release_interface+0x70/0x88
<4>[ 29.158325] btusb_mtk_release_iso_intf+0x68/0xd8 [btusb (HASH:e8b6 5)]
<4>[ 29.158347] btusb_mtk_reset+0x5c/0x480 [btusb (HASH:e8b6 5)]
<4>[ 29.158361] hci_cmd_sync_work+0x10c/0x188 [bluetooth (HASH:a4fa 6)]
<4>[ 29.158430] process_scheduled_works+0x258/0x4e8
<4>[ 29.158441] worker_thread+0x300/0x428
<4>[ 29.158448] kthread+0x108/0x1d0
<4>[ 29.158455] ret_from_fork+0x10/0x20
<0>[ 29.158467] Code: 91343000 940139d1 f9400268 927ff914 (f9401297)
<4>[ 29.158474] ---[ end trace 0000000000000000 ]---
<0>[ 29.167129] Kernel panic - not syncing: Oops: Fatal exception
<2>[ 29.167144] SMP: stopping secondary CPUs
<4>[ 29.167158] ------------[ cut here ]------------
Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
For chips with security enabled, it's only possible to load firmware
with a valid signature pattern.
If key_id is not zero, it indicates a security chip, and the driver will
not load the config file.
- Example log for a security chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301
Bluetooth: hci0: RTL: fw version 0x41c0c905
- Example log for a normal chip.
Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a
lmp_ver=0c lmp_subver=8922
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: btrtl_initialize: key id 0
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin
Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307
Bluetooth: hci0: RTL: fw version 0x41c0c905
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Nial Ni <niall_ni@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There is a KASAN: slab-use-after-free read in btusb_disconnect().
Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will
free the btusb data associated with the interface. The same data is
then used later in the function, hence the UAF.
Fix by moving the accesses to btusb data to before the data is free'd.
Reported-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fc81b50a4f8263a159b
Tested-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Fixes: fd913ef7ce619 ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The memory allocated for ptr using kvmalloc() is not freed on the last
error path. Fix that by freeing it on that error path.
Fixes: 9a24ce5e29b1 ("Bluetooth: btrtl: Firmware format v2 support")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
A different structure is stored in drvdata for the drivers which used
that duplicate function, but h4_recv_buf() assumes drvdata is always an
hci_uart structure.
Consequently, alignment and padding are now randomly corrupted for
btmtkuart, btnxpuart, and bpa10x in h4_recv_buf(), causing erratic
breakage.
Fix this by making the hci_uart structure the explicit argument to
h4_recv_buf(). Every caller already has a reference to hci_uart, and
already obtains the hci_hdev reference through it, so this actually
eliminates a redundant pointer indirection for all existing callers.
Fixes: 93f06f8f0daf ("Bluetooth: remove duplicate h4_recv_buf() in header")
Reported-by: Francesco Valla <francesco@valla.it>
Closes: https://lore.kernel.org/lkml/6837167.ZASKD2KPVS@fedora.fritz.box/
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the current btintel_pcie driver implementation, when an interrupt is
received, the driver checks for the alive cause before the TX/RX cause.
Handling the alive cause involves resetting the TX/RX queue indices.
This flow works correctly when the causes are mutually exclusive.
However, if both cause bits are set simultaneously, the alive cause
resets the queue indices, resulting in an event packet drop and a
command timeout. To fix this issue, the driver is modified to handle all
other causes before checking for the alive cause.
Test case:
Issue is seen with stress reboot scenario - 50x run
[20.337589] Bluetooth: hci0: Device revision is 0
[20.346750] Bluetooth: hci0: Secure boot is enabled
[20.346752] Bluetooth: hci0: OTP lock is disabled
[20.346752] Bluetooth: hci0: API lock is enabled
[20.346752] Bluetooth: hci0: Debug lock is disabled
[20.346753] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[20.346754] Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
[20.359070] Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
[20.371499] Bluetooth: hci0: Boot Address: 0xb02ff800
[20.385769] Bluetooth: hci0: Firmware Version: 166-34.25
[20.538257] Bluetooth: hci0: Waiting for firmware download to complete
[20.554424] Bluetooth: hci0: Firmware loaded in 178651 usecs
[21.081588] Bluetooth: hci0: Timeout (500 ms) on tx completion
[21.096541] Bluetooth: hci0: Failed to send frame (-62)
[21.110240] Bluetooth: hci0: sending frame failed (-62)
[21.138551] Bluetooth: hci0: Failed to send Intel Reset command
[21.170153] Bluetooth: hci0: Intel Soft Reset failed (-62)
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds logic to handle power management control when the
Bluetooth function is closed during the SDIO reset sequence.
Specifically, if BT is closed before reset, the driver enables the
SDIO function and sets driver pmctrl. After reset, if BT remains
closed, the driver sets firmware pmctrl and disables the SDIO function.
These changes ensure proper power management and device state consistency
across the reset flow.
Fixes: 8fafe702253d ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Currently, bcsp_recv() can be called even when the BCSP protocol has not
been registered. This leads to a NULL pointer dereference, as shown in
the following stack trace:
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590
Call Trace:
<TASK>
hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627
tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290
tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
To prevent this, ensure that the HCI_UART_REGISTERED flag is set before
processing received data. If the protocol is not registered, return
-EUNATCH.
Reported-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=4ed6852d4da4606c93da
Tested-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3633 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3633 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3627 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3627 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The "h4_recv.h" header contains a duplicate h4_recv_buf() that is nearly
but not quite identical to the h4_recv_buf() in hci_h4.c.
This duplicated header was added in commit 07eb96a5a7b0 ("Bluetooth:
bpa10x: Use separate h4_recv_buf helper"). I wasn't able to find any
explanation for duplicating the code in the discussion:
https://lore.kernel.org/all/20180320181855.37297-1-marcel@holtmann.org/
https://lore.kernel.org/all/20180324091954.73229-2-marcel@holtmann.org/
Unfortunately, in the years since, several other drivers have come to
also rely on this duplicated function, probably by accident. This is, at
the very least, *extremely* confusing. It's also caused real issues when
it's become out-of-sync, see the following:
ef564119ba83 ("Bluetooth: hci_h4: Add support for ISO packets")
61b27cdf025b ("Bluetooth: hci_h4: Add support for ISO packets in h4_recv.h")
This is the full diff between the two implementations today:
--- orig.c
+++ copy.c
@@ -1,117 +1,100 @@
{
- struct hci_uart *hu = hci_get_drvdata(hdev);
- u8 alignment = hu->alignment ? hu->alignment : 1;
-
/* Check for error from previous call */
if (IS_ERR(skb))
skb = NULL;
while (count) {
int i, len;
- /* remove padding bytes from buffer */
- for (; hu->padding && count > 0; hu->padding--) {
- count--;
- buffer++;
- }
- if (!count)
- break;
-
if (!skb) {
for (i = 0; i < pkts_count; i++) {
if (buffer[0] != (&pkts[i])->type)
continue;
skb = bt_skb_alloc((&pkts[i])->maxlen,
GFP_ATOMIC);
if (!skb)
return ERR_PTR(-ENOMEM);
hci_skb_pkt_type(skb) = (&pkts[i])->type;
hci_skb_expect(skb) = (&pkts[i])->hlen;
break;
}
/* Check for invalid packet type */
if (!skb)
return ERR_PTR(-EILSEQ);
count -= 1;
buffer += 1;
}
len = min_t(uint, hci_skb_expect(skb) - skb->len, count);
skb_put_data(skb, buffer, len);
count -= len;
buffer += len;
/* Check for partial packet */
if (skb->len < hci_skb_expect(skb))
continue;
for (i = 0; i < pkts_count; i++) {
if (hci_skb_pkt_type(skb) == (&pkts[i])->type)
break;
}
if (i >= pkts_count) {
kfree_skb(skb);
return ERR_PTR(-EILSEQ);
}
if (skb->len == (&pkts[i])->hlen) {
u16 dlen;
switch ((&pkts[i])->lsize) {
case 0:
/* No variable data length */
dlen = 0;
break;
case 1:
/* Single octet variable length */
dlen = skb->data[(&pkts[i])->loff];
hci_skb_expect(skb) += dlen;
if (skb_tailroom(skb) < dlen) {
kfree_skb(skb);
return ERR_PTR(-EMSGSIZE);
}
break;
case 2:
/* Double octet variable length */
dlen = get_unaligned_le16(skb->data +
(&pkts[i])->loff);
hci_skb_expect(skb) += dlen;
if (skb_tailroom(skb) < dlen) {
kfree_skb(skb);
return ERR_PTR(-EMSGSIZE);
}
break;
default:
/* Unsupported variable length */
kfree_skb(skb);
return ERR_PTR(-EILSEQ);
}
if (!dlen) {
- hu->padding = (skb->len + 1) % alignment;
- hu->padding = (alignment - hu->padding) % alignment;
-
/* No more data, complete frame */
(&pkts[i])->recv(hdev, skb);
skb = NULL;
}
} else {
- hu->padding = (skb->len + 1) % alignment;
- hu->padding = (alignment - hu->padding) % alignment;
-
/* Complete frame */
(&pkts[i])->recv(hdev, skb);
skb = NULL;
}
}
return skb;
}
-EXPORT_SYMBOL_GPL(h4_recv_buf)
As I read this: If alignment is one, and padding is zero, padding
remains zero throughout the loop. So it seems to me that the two
functions behave strictly identically in that case. All the duplicated
defines are also identical, as is the duplicated h4_recv_pkt structure
declaration.
All four drivers which use the duplicated function use the default
alignment of one, and the default padding of zero. I therefore conclude
the duplicate function may be safely replaced with the core one.
I raised this in an RFC a few months ago, and didn't get much interest:
https://lore.kernel.org/all/CABBYNZ+ONkYtq2fR-8PtL3X-vetvJ0BdP4MTw9cNpjLDzG3HUQ@mail.gmail.com/
...but I'm still wary I've missed something, and I'd really appreciate
more eyeballs on it.
I tested this successfully on btnxpuart a few months ago, but
unfortunately I no longer have access to that hardware.
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some Barrot based USB Bluetooth dongles erroneously send one extra
random byte for the HCI_OP_READ_LOCAL_EXT_FEATURES command. The
consequence of that is that the next HCI transfer is misaligned by one
byte causing undefined behavior. In most cases the response event for
the next command fails with random error code.
Since the HCI_OP_READ_LOCAL_EXT_FEATURES command is used during HCI
controller initialization, the initialization fails rendering the USB
dongle not usable.
> [59.464099] usb 1-1.3: new full-speed USB device number 11 using xhci_hcd
> [59.561617] usb 1-1.3: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91
> [59.561642] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
> [59.561656] usb 1-1.3: Product: UGREEN BT6.0 Adapter
> [61.720116] Bluetooth: hci1: command 0x1005 tx timeout
> [61.720167] Bluetooth: hci1: Opcode 0x1005 failed: -110
This patch was tested with the 33fa:0012 device. The info from the
/sys/kernel/debug/usb/devices is shown below:
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 12 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=33fa ProdID=0012 Rev=88.91
S: Product=UGREEN BT6.0 Adapter
C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Now the device is initialized properly:
> [43.329852] usb 1-1.4: new full-speed USB device number 4 using dwc_otg
> [43.446790] usb 1-1.4: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91
> [43.446813] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
> [43.446821] usb 1-1.4: Product: UGREEN BT6.0 Adapter
> [43.582024] Bluetooth: hci1: Unexpected continuation: 1 bytes
> [43.703025] Bluetooth: hci1: Unexpected continuation: 1 bytes
> [43.750141] Bluetooth: MGMT ver 1.23
Link: https://github.com/bluez/bluez/issues/1326
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Tested-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
As device coredumps are not HCI traces, maintain the device coredump at
the driver level and eliminate the dependency on hdev_devcd*()
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: 07e6bddb54b4 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
kzalloc() already zero-initializes the destination buffer 'data', making
strscpy() sufficient for safely copying 'name'. The additional
NUL-padding performed by strscpy_pad() is unnecessary.
Add a new local variable to store the length of 'name' and reuse it
instead of recalculating the same length.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Implement hdev->wakeup() callback to support Wake On BT feature.
Test steps:
1. echo enabled > /sys/bus/pci/devices/0000:00:14.7/power/wakeup
2. connect bluetooth hid device
3. put the system to suspend - rtcwake -m mem -s 300
4. press any key on hid to wake up the system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 2001:332a for D-Link AX9U rev. A1 which is based on a Realtek
RTL8851BU chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=332a Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11ax WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org # 6.12.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This prevents the comments going over 80 columns which is still
required for Bluetooth code.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
sudo lspci -v -k -d 8086:e376
00:14.7 Bluetooth: Intel Corporation Device e376
Subsystem: Intel Corporation Device 0011
Flags: bus master, fast devsel, latency 0, IRQ 16, IOMMU group 14
Memory at 14815368000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [80] MSI-X: Enable+ Count=32 Masked-
Capabilities: [100] Latency Tolerance Reporting
Kernel driver in use: btintel_pcie
Kernel modules: btintel_pcie
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add Bluetooth CNVi core and platform names to the PCI device table for
each device ID as a comment.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch implements _suspend() and _resume() functions for the
Bluetooth controller. When the system enters a suspended state, the
driver notifies the controller to perform necessary housekeeping tasks
by writing to the sleep control register and waits for an alive
interrupt. The firmware raises the alive interrupt when it has
transitioned to the D3 state. The same flow occurs when the system
resumes.
Command to test host initiated wakeup after 60 seconds
sudo rtcwake -m mem -s 60
dmesg log (tested on Whale Peak2 on Panther Lake platform)
On system suspend:
[Fri Jul 25 11:05:37 2025] Bluetooth: hci0: device entered into d3 state from d0 in 80 us
On system resume:
[Fri Jul 25 11:06:36 2025] Bluetooth: hci0: device entered into d0 state from d3 in 7117 us
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for the BlazarIW Bluetooth core used in the Wildcat Lake
platform.
HCI traces:
< HCI Command: Intel Read Version (0x3f|0x0005) plen 1
Requested Type:
All Supported Types(0xff)
> HCI Event: Command Complete (0x0e) plen 122
Intel Read Version (0x3f|0x0005) ncmd 1
Status: Success (0x00)
.....
CNVi BT(18): 0x00223700 - BlazarIW(0x22)
.....
.....
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some Kconfig dependencies are needed after my recent cleanup, since
the core code has its own option.
Since btmtksdio does not actually call h4_recv_buf(), move the
definitions it uses outside the BT_HCIUART_H4 gate in hci_uart.h to
avoid adding a dependency for btmtksdio.
The rest I touched (bpa10x, btmtkuart, and btnxpuart) do really call
h4_recv_buf(), so the dependency is required, add it for them.
Fixes: 0e272fc7e17d ("Bluetooth: remove duplicate h4_recv_buf() in header")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508300413.OnIedvRh-lkp@intel.com/
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move the creation of debugfs files into a dedicated function, and ensure
they are explicitly removed during vhci_release(), before associated
data structures are freed.
Previously, debugfs files such as "force_suspend", "force_wakeup", and
others were created under hdev->debugfs but not removed in
vhci_release(). Since vhci_release() frees the backing vhci_data
structure, any access to these files after release would result in
use-after-free errors.
Although hdev->debugfs is later freed in hci_release_dev(), user can
access files after vhci_data is freed but before hdev->debugfs is
released.
Fixes: ab4e4380d4e1 ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This replaces devm_request_irq() with devm_request_threaded_irq().
On iMX93 11x11 EVK platform, the BT chip's BT_WAKE_OUT pin is connected
to an I2C GPIO expander instead of directly been connected to iMX GPIO.
When I2C GPIO expander's (PCAL6524) host driver receives an interrupt on
it's INTR line, the driver's interrupt handler needs to query the
interrupt source with PCAL6524 first, and then call the actual interrupt
handler, in this case the IRQ handler in BTNXPUART.
In order to handle interrupts when such I2C GPIO expanders are between
the host and interrupt source, devm_request_threaded_irq() is needed.
This commit also removes the IRQF_TRIGGER_FALLING flag, to allow setting
the IRQ trigger type from the device tree setting instead of hardcoding
in the driver.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
