| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 028a73e10705af1ffd51f2537460f616dc58680e upstream.
On some servers with MGA G200_SE_A (rev 42), booting with Legacy BIOS,
the hardware hangs when using kdump and kexec into the kdump kernel.
This happens when the uncompress code tries to write "Decompressing Linux"
to the VGA Console.
It can be reproduced by writing to the VGA console (0xB8000) after
booting to graphic mode, it generates the following error:
kernel:NMI: PCI system error (SERR) for reason a0 on CPU 0.
kernel:Dazed and confused, but trying to continue
The root cause is the configuration of the MGA GCTL6 register
According to the GCTL6 register documentation:
bit 0 is gcgrmode:
0: Enables alpha mode, and the character generator addressing system is
activated.
1: Enables graphics mode, and the character addressing system is not
used.
bit 1 is chainodd even:
0: The A0 signal of the memory address bus is used during system memory
addressing.
1: Allows A0 to be replaced by either the A16 signal of the system
address (ifmemmapsl is ‘00’), or by the hpgoddev (MISC<5>, odd/even
page select) field, described on page 3-294).
bit 3-2 are memmapsl:
Memory map select bits 1 and 0. VGA.
These bits select where the video memory is mapped, as shown below:
00 => A0000h - BFFFFh
01 => A0000h - AFFFFh
10 => B0000h - B7FFFh
11 => B8000h - BFFFFh
bit 7-4 are reserved.
Current code set it to 0x05 => memmapsl to b01 => 0xa0000 (graphic mode)
But on x86, the VGA console is at 0xb8000 (text mode)
In arch/x86/boot/compressed/misc.c debug strings are written to 0xb8000
As the driver doesn't use this mapping at 0xa0000, it is safe to set it to
0xb8000 instead, to avoid kernel hang on G200_SE_A rev42, with kexec/kdump.
Thus changing the value 0x05 to 0x0d
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119102905.1194787-1-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5662abf6e21338be6d085d6375d3732ac6147fd2 upstream.
Tag code stored in bit7:5 for CTA block byte[3] is not the same as
CEA extension block definition. Only check CEA block has
basic audio support.
v3: update commit message.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Signed-off-by: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: e28ad544f462 ("drm/edid: parse CEA blocks embedded in DisplayID")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220324061218.32739-1-shawn.c.lee@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fc1b6ef7bfb3d1d4df868b1c3e0480cacda6cd81 ]
The Innolux G070Y2-L01 supports two modes of operation:
1) FRC=Low/NC ... MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ... BPP=6
2) FRC=High ..... MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ... BPP=8
Currently the panel description mixes both, BPP from 1) and bus
format from 2), which triggers a warning at panel-simple.c:615.
Pick the later, set bpp=8, fix the warning.
Fixes: a5d2ade627dca ("drm/panel: simple: Add support for Innolux G070Y2-L01")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220220040718.532866-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
imx_pd_bridge_atomic_check()
[ Upstream commit 6061806a863e8b65b109eb06a280041cc7525442 ]
If display timings were read from the devicetree using
of_get_display_timing() and pixelclk-active is defined
there, the flag DISPLAY_FLAGS_SYNC_POSEDGE/NEGEDGE is
automatically generated. Through the function
drm_bus_flags_from_videomode() e.g. called in the
panel-simple driver this flag got into the bus flags,
but then in imx_pd_bridge_atomic_check() the bus flag
check failed and will not initialize the display. The
original commit fe141cedc433 does not explain why this
check was introduced. So remove the bus flags check,
because it stops the initialization of the display with
valid bus flags.
Fixes: fe141cedc433 ("drm/imx: pd: Use bus format/flags provided by the bridge when available")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org
To: dri-devel@lists.freedesktop.org
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201113643.4638-1-cniedermaier@dh-electronics.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62929726ef0ec72cbbe9440c5d125d4278b99894 ]
VRR capable property is not attached by default to the connector
It is attached only if VRR is supported.
So if the driver tries to call drm core set prop function without
it being attached that causes NULL dereference.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225013055.9282-1-manasi.d.navare@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9470c29faa91c804aa04de4c10634bf02462bfa5 ]
It turns out that DE3 manual has inverted YUV and YVU format numbers for
P010 and P210. Invert them.
This was tested by playing video decoded to P010 and additionally
confirmed by looking at BSP driver source.
Fixes: 169ca4b38932 ("drm/sun4i: Add separate DE3 VI layer formats")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181436.1424550-1-jernej.skrabec@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f1ef17011c765495c876fa75435e59eecfdc1ee4 ]
Regression has been reported that suspend/resume may hang with
the previous vm ready check commit.
So bring back the evicted list check as a temp fix.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1922
Fixes: c1a66c3bc425 ("drm/amdgpu: check vm ready by amdgpu_vm->evicting flag")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Qiang Yu <qiang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 08783aa7693f55619859f4f63f384abf17cb58c5 upstream.
This JSP2 PCH actually seems to be some special Apple
specific ICP variant rather than a JSP. Make it so. Or at
least all the references to it seem to be some Apple ICL
machines. Didn't manage to find these PCI IDs in any
public chipset docs unfortunately.
The only thing we're losing here with this JSP->ICP change
is Wa_14011294188, but based on the HSD that isn't actually
needed on any ICP based design (including JSP), only TGP
based stuff (including MCC) really need it. The documented
w/a just never made that distinction because Windows didn't
want to differentiate between JSP and MCC (not sure how
they handle hpd/ddc/etc. then though...).
Cc: stable@vger.kernel.org
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4226
Fixes: 943682e3bd19 ("drm/i915: Introduce Jasper Lake PCH")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224132142.12927-1-ville.syrjala@linux.intel.com
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Tested-by: Tomas Bzatek <bugs@bzatek.net>
(cherry picked from commit 53581504a8e216d435f114a4f2596ad0dfd902fc)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c1a66c3bc425ff93774fb2f6eefa67b83170dd7e ]
Workstation application ANSA/META v21.1.4 get this error dmesg when
running CI test suite provided by ANSA/META:
[drm:amdgpu_gem_va_ioctl [amdgpu]] *ERROR* Couldn't update BO_VA (-16)
This is caused by:
1. create a 256MB buffer in invisible VRAM
2. CPU map the buffer and access it causes vm_fault and try to move
it to visible VRAM
3. force visible VRAM space and traverse all VRAM bos to check if
evicting this bo is valuable
4. when checking a VM bo (in invisible VRAM), amdgpu_vm_evictable()
will set amdgpu_vm->evicting, but latter due to not in visible
VRAM, won't really evict it so not add it to amdgpu_vm->evicted
5. before next CS to clear the amdgpu_vm->evicting, user VM ops
ioctl will pass amdgpu_vm_ready() (check amdgpu_vm->evicted)
but fail in amdgpu_vm_bo_update_mapping() (check
amdgpu_vm->evicting) and get this error log
This error won't affect functionality as next CS will finish the
waiting VM ops. But we'd better clear the error log by checking
the amdgpu_vm->evicting flag in amdgpu_vm_ready() to stop calling
amdgpu_vm_bo_update_mapping() later.
Another reason is amdgpu_vm->evicted list holds all BOs (both
user buffer and page table), but only page table BOs' eviction
prevent VM ops. amdgpu_vm->evicting flag is set only for page
table BOs, so we should use evicting flag instead of evicted list
in amdgpu_vm_ready().
The side effect of this change is: previously blocked VM op (user
buffer in "evicted" list but no page table in it) gets done
immediately.
v2: update commit comments.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Qiang Yu <qiang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ecbd4912a693b862e25cba0a6990a8c95b00721e upstream.
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71ad8 ("drm: parse color format support for digital displays")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afc189df6bcc6be65961deb54e15ec60e7f85337 upstream.
When changing between SAGV vs. no SAGV on tgl+ we have to
update the use_sagv_wm flag for all the crtcs or else
an active pipe not already in the state will end up using
the wrong watermarks. That is especially bad when we end up
with the tighter non-SAGV watermarks with SAGV enabled.
Usually ends up in underruns.
Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 7241c57d3140 ("drm/i915: Add TGL+ SAGV support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-2-ville.syrjala@linux.intel.com
(cherry picked from commit 8dd8ffb824ca7b897ce9f2082ffa7e64831c22dc)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f626dd0ff05043e5a7154770cc7cda66acee33a3 upstream.
MMHUB PG needs to be disabled for Picasso for stability reasons.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c0cfbb122275da1b726481de5a8cffeb24e6322b ]
The driver returns an error when devm_phy_optional_get() fails leaving
the previously enabled clock turned on. Change order and enable the
clock only after the phy has been acquired.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126145549.617165-3-s.hauer@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d72d69abfdb6e0375981cfdda8eb45143f12c77d upstream.
GVT is not supported on non-x86 platforms, So add
dependency of X86 on config parameter DRM_I915_GVT.
Fixes: 0ad35fed618c ("drm/i915: gvt: Introduce the basic architecture of GVT-g")
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220107095235.243448-1-siva.mullati@intel.com
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea958422291de248b9e2eaaeea36004e84b64043 upstream.
The mapping from enum port to whatever port numbering scheme is used by
the SWSCI Display Power State Notification is odd, and the memory of it
has faded. In any case, the parameter only has space for ports numbered
[0..4], and UBSAN reports bit shift beyond it when the platform has port
F or more.
Since the SWSCI functionality is supposed to be obsolete for new
platforms (i.e. ones that might have port F or more), just bail out
early if the mapped and mangled port number is beyond what the Display
Power State Notification can support.
Fixes: 9c4b0a683193 ("drm/i915: add opregion function to notify bios of encoder enable/disable")
Cc: <stable@vger.kernel.org> # v3.13+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4800
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cc363f42d6b5a5932b6d218fefcc8bdfb15dbbe5.1644489329.git.jani.nikula@intel.com
(cherry picked from commit 24a644ebbfd3b13cda702f98907f9dd123e34bf9)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 364438fd629f7611a84c8e6d7de91659300f1502 upstream.
The iMac 12,1 does not use the gmux driver for backlight, so the radeon
backlight device is needed to set the brightness.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1838
Signed-off-by: Nicholas Bishop <nicholasbishop@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e8ae38720e1a685fd98cfa5ae118c9d07b45ca79 ]
We probably never trigger this, but the logic inside the check is
inverted.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4cdd2450bf739bada353e82d27b00db9af8c3001 upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6df4432a5eca101b5fd80fbee41d309f3d67928d ]
In the function panel_simple_probe() the pointer panel->desc is
assigned to the passed pointer desc. If function panel_dpi_probe()
is called panel->desc will be updated, but further on only desc
will be evaluated. So update the desc pointer to be able to use
the data from the function panel_dpi_probe().
Fixes: 4a1d0dbc8332 ("drm/panel: simple: add panel-dpi support")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201110153.3479-1-cniedermaier@dh-electronics.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d118965965f89948236ebe23072bb1fca5e7832 ]
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632be ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9da1e9ab82c92d0e89fe44cad2cd7c2d18d64070 upstream.
Commit 7707f7227f09 ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f09. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f09 ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d3cbc6e323c9299d10c8d2e4127c77c7d05d07b1 ]
The 1Netbook OneXPlayer uses a panel which has been mounted
90 degrees rotated. Add a quirk for this.
Signed-off-by: Raymond Jay Golo <rjgolo@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113000619.90988-1-rjgolo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f4d3da72a76a9ce5f57bba64788931686a9dc333 upstream.
In Mesa, dev_info.gart_page_size is used for alignment and it was
set to AMDGPU_GPU_PAGE_SIZE(4KB). However, the page table of AMDGPU
driver requires an alignment on CPU pages. So, for non-4KB page system,
gart_page_size should be max_t(u32, PAGE_SIZE, AMDGPU_GPU_PAGE_SIZE).
Signed-off-by: Rui Wang <wangr@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Link: https://github.com/loongson-community/linux-stable/commit/caa9c0a1
[Xi: rebased for drm-next, use max_t for checkpatch,
and reworded commit message.]
Signed-off-by: Xi Ruoyao <xry111@mengyan1223.wang>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1549
Tested-by: Dan Horák <dan@danny.cz>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Salvatore Bonaccorso: Backport to 5.10.y which does not contain
a5a52a43eac0 ("drm/amd/amdgpu/amdgpu_kms: Remove 'struct
drm_amdgpu_info_device dev_info' from the stack") which removes dev_info
from the stack and places it on the heap.]
Tested-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90a3d22ff02b196d5884e111f39271a1d4ee8e3e upstream.
Smatch detected a divide by zero bug in check_overlay_scaling().
drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_height'.
drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_width'.
Prevent this by ensuring that the dst height and width are non-zero.
Fixes: 02e792fbaadb ("drm/i915: implement drmmode overlay support v4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
(cherry picked from commit cf5b64f7f10b28bebb9b7c9d25e7aee5cbe43918)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
panels
commit 30fbce374745a9c6af93c775a5ac49a97f822fda upstream.
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b777d4d9e383d2744fc9b3a09af6ec1893c8b1a upstream.
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff572 ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 55b10b88ac8654fc2f31518aa349a2e643b37f18 which is
commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.
It wasn't applied correctly, something went wrong with an attempt to fix
it up again, so just revert the whole thing to be back at a clean state.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220205171238.GA3073350@roeck-us.net
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/Yf5lNIJnvhP4ajam@kroah.com
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit ac4ba79bb02881ed714adaa89faee601a18bff6d which is
commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.
It wasn't applied correctly, something went wrong with an attempt to fix
it up again, so just revert the whole thing to be back at a clean state.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220205171238.GA3073350@roeck-us.net
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/Yf5lNIJnvhP4ajam@kroah.com
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.
The original commit depended on a rework commit (724fc856c09e ("drm/vc4:
hdmi: Split the CEC disable / enable functions in two")) that
(rightfully) didn't reach stable.
However, probably because the context changed, when the patch was
applied to stable the pm_runtime_put called got moved to the end of the
vc4_hdmi_cec_adap_enable function (that would have become
vc4_hdmi_cec_disable with the rework) to vc4_hdmi_cec_init.
This means that at probe time, we now drop our reference to the clocks
and power domains and thus end up with a CPU hang when the CPU tries to
access registers.
The call to pm_runtime_resume_and_get() is also problematic since the
.adap_enable CEC hook is called both to enable and to disable the
controller. That means that we'll now call pm_runtime_resume_and_get()
at disable time as well, messing with the reference counting.
The behaviour we should have though would be to have
pm_runtime_resume_and_get() called when the CEC controller is enabled,
and pm_runtime_put when it's disabled.
We need to move things around a bit to behave that way, but it aligns
stable with upstream.
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: <stable@vger.kernel.org> # 5.15.x
Cc: <stable@vger.kernel.org> # 5.16.x
Reported-by: Michael Stapelberg <michael+drm@stapelberg.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 170b22234d5495f5e0844246e23f004639ee89ba ]
The function performs a check on the "ctx" input parameter, however, it
is used before the check.
Initialize the "base" variable after the sanity check to avoid a
possible NULL pointer dereference.
Fixes: 4259ff7ae509e ("drm/msm/dpu: add support for pcc color block in dpu driver")
Addresses-Coverity-ID: 1493866 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220109192431.135949-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 774fe0cd838d1b1419d41ab4ea0613c80d4ecbd7 ]
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Fixes: e00012b256d4 ("drm/msm/hdmi: Make HDMI core get its PHY")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220107085026.23831-1-linmq006@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5e761a2287234bc402ba7ef07129f5103bcd775c upstream.
The function performs a check on the "phy" input parameter, however, it
is used before the check.
Initialize the "dev" variable after the sanity check to avoid a possible
NULL pointer dereference.
Fixes: 5c8290284402b ("drm/msm/dsi: Split PHY drivers to separate files")
Addresses-Coverity-ID: 1493860 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220116181844.7400-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c04c3148ca12227d92f91b355b4538cc333c9922 upstream.
If of_find_device_by_node() succeeds, dsi_get_phy() doesn't
a corresponding put_device(). Thus add put_device() to fix the exception
handling.
Fixes: ec31abf ("drm/msm/dsi: Separate PHY to another platform device")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211230070943.18116-1-linmq006@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a727b459ee39bd4c5ced19d6024258ac87b6b2e upstream.
For example, memory-region in .dts as below,
reg = <0x0 0x50000000 0x0 0x20000000>
We can get below values,
struct resource r;
r.start = 0x50000000;
r.end = 0x6fffffff;
So the size should be:
size = r.end - r.start + 1 = 0x20000000
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Fixes: 072f1f9168ed ("drm/msm: add support for "stolen" mem")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220112123334.749776-1-xianting.tian@linux.alibaba.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e3d26528e083e612314d4dcd713f3d5a26143ddc upstream.
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0f90c8815706981c483a652a6aefca51a5e191c upstream.
A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
Fixes: c906965dee22 ("drm/vmwgfx: Add export fence to file descriptor support")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7938d61591d33394a21bdd7797a245b65428f44c upstream.
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20b0dfa86bef0e80b41b0e5ac38b92f23b6f27f9 upstream.
Similarly to what we encountered with the detect hook with DRM, nothing
actually prevents any of the CEC callback from being run while the HDMI
output is disabled.
However, this is an issue since any register access to the controller
when it's powered down will result in a silent hang.
Let's make sure we run the runtime_pm hooks when the CEC adapter is
opened and closed by the userspace to avoid that issue.
Fixes: 15b4511a4af6 ("drm/vc4: add HDMI CEC support")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-6-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4722f463896cc0ef1a6f1c3cb2e171e949831249 upstream.
The return value was never initialized so the cleanup code executed when
it isn't even necessary.
Just add proper error handling.
Fixes: ab50cb9df889 ("drm/radeon/radeon_kms: Fix a NULL pointer dereference in radeon_driver_open_kms()")
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4c6ef229593366ab593d4d424addc7025b54a76 upstream.
Prior to commit 6c836d965bad ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:
"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""
However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.
It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:
According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."
Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.
Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.
Fixes: 6c836d965bad ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd6e07e72f37f34535bec7eebc807e5fcfe37b43 upstream.
The struct is giant, and triggers an order-7 allocation (512K). There is
no reason for this to be kmalloc-type memory, so switch to vmalloc. This
should help loading nouveau on low-memory and/or long-running systems.
Reported-by: Nathan E. Egge <unlord@xiph.org>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dfa2fab8ddd46faa771a102672176bee7a065de upstream.
Currently we allow rediculous amounts of kernel memory being allocated
via the etnaviv GEM_SUBMIT ioctl, which is a pretty easy DoS vector. Put
some reasonable limits in to fix this.
The commandstream size is limited to 64KB, which was already a soft limit
on older kernels after which the kernel only took submits on a best effort
base, so there is no userspace that tries to submit commandstreams larger
than this. Even if the whole commandstream is a single incrementing address
load, the size limit also limits the number of potential relocs and
referenced buffers to slightly under 64K, so use the same limit for those
arguments. The performance monitoring infrastructure currently supports
less than 50 performance counter signals, so limiting them to 128 on a
single submit seems like a reasonably future-proof number for now. This
number can be bumped if needed without breaking the interface.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 399c91c3f30531593e5ff6ca7b53f47092128669 ]
The of_device_get_match_data() function may return NULL.
Add check to prevent potential null dereference.
Signed-off-by: Miaoqian Lin < |
