| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 2682468671aa0b4d52ae09779b48212a80d71b91 upstream.
When a user requests more than 60 bytes of data the MCP2221 must chunk
the data in chunks up to 60 bytes long (see command/response code 0x40
in the datasheet).
In order to signal that the device has more data the (undocumented) byte
at byte index 2 of the Get I2C Data response uses the value 0x54. This
contrasts with the case for the final data chunk where the value
returned is 0x55 (MCP2221_I2C_READ_COMPL). The fact that 0x55 was not
returned in the response was interpreted by the driver as a failure
meaning that all reads of more than 60 bytes would fail.
Add support for reads that are split over multiple chunks by looking for
the response code indicating that more data is expected and continuing
the read as the code intended. Some timing delays are required to ensure
the chip has time to refill its FIFO as data is read in from the I2C
bus. This timing has been tested in my system when configured for bus
speeds of 50KHz, 100KHz, and 400KHz and operates well.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes: 67a95c21463d0 ("HID: mcp2221: add usb to i2c-smbus host bridge")
[romain.sioen@microchip.com: backport to stable, up to 6.8. Add "Fixes" tag]
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02a46753601a24e1673d9c28173121055e8e6cc9 upstream.
Since the initial commit of this driver the I2C bus speed has been
reconfigured for every single transfer. This is despite the fact that we
never change the speed and it is never "lost" by the chip.
Upon investigation we find that what was really happening was that the
setting of the bus speed had the side effect of cancelling a previous
failed command if there was one, thereby freeing the bus. This is the
part that was actually required to keep the bus operational in the face
of failed commands.
Instead of always setting the speed, we now correctly cancel any failed
commands as they are detected. This means we can just set the bus speed
at probe time and remove the previous speed sets on each transfer.
This has the effect of improving performance and reducing the number of
commands required to complete transfers.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes: 67a95c21463d ("HID: mcp2221: add usb to i2c-smbus host bridge")
[romain.sioen@microchip.com: backport to stable, up to 6.8. Add "Fixes" tag]
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 185c926283da67a72df20a63a5046b3b4631b7d9 upstream.
in ntrig_report_version(), hdev parameter passed from hid_probe().
sending descriptor to /dev/uhid can make hdev->dev.parent->parent to null
if hdev->dev.parent->parent is null, usb_dev has
invalid address(0xffffffffffffff58) that hid_to_usb_dev(hdev) returned
when usb_rcvctrlpipe() use usb_dev,it trigger
page fault error for address(0xffffffffffffff58)
add null check logic to ntrig_report_version()
before calling hid_to_usb_dev()
Signed-off-by: Minjong Kim <minbell.kim@samsung.com>
Link: https://patch.msgid.link/20250813-hid-ntrig-page-fault-fix-v2-1-f98581f35106@samsung.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9fc51941d9e7793da969b2c66e6f8213c5b1237f upstream.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3af6ca9a8c34bbd8cff32b469b84c9021c9e7e4 upstream.
After hid_hw_start() is called hidinput_connect() will eventually be
called to set up the device with the input layer since the
HID_CONNECT_DEFAULT connect mask is used. During hidinput_connect()
all input and output reports are processed and corresponding hid_inputs
are allocated and configured via hidinput_configure_usages(). This
process involves slot tagging report fields and configuring usages
by setting relevant bits in the capability bitmaps. However it is possible
that the capability bitmaps are not set at all leading to the subsequent
hidinput_has_been_populated() check to fail leading to the freeing of the
hid_input and the underlying input device.
This becomes problematic because a malicious HID device like a
ASUS ROG N-Key keyboard can trigger the above scenario via a
specially crafted descriptor which then leads to a user-after-free
when the name of the freed input device is written to later on after
hid_hw_start(). Below, report 93 intentionally utilises the
HID_UP_UNDEFINED Usage Page which is skipped during usage
configuration, leading to the frees.
0x05, 0x0D, // Usage Page (Digitizer)
0x09, 0x05, // Usage (Touch Pad)
0xA1, 0x01, // Collection (Application)
0x85, 0x0D, // Report ID (13)
0x06, 0x00, 0xFF, // Usage Page (Vendor Defined 0xFF00)
0x09, 0xC5, // Usage (0xC5)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x04, // Report Count (4)
0xB1, 0x02, // Feature (Data,Var,Abs)
0x85, 0x5D, // Report ID (93)
0x06, 0x00, 0x00, // Usage Page (Undefined)
0x09, 0x01, // Usage (0x01)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x1B, // Report Count (27)
0x81, 0x02, // Input (Data,Var,Abs)
0xC0, // End Collection
Below is the KASAN splat after triggering the UAF:
[ 21.672709] ==================================================================
[ 21.673700] BUG: KASAN: slab-use-after-free in asus_probe+0xeeb/0xf80
[ 21.673700] Write of size 8 at addr ffff88810a0ac000 by task kworker/1:2/54
[ 21.673700]
[ 21.673700] CPU: 1 UID: 0 PID: 54 Comm: kworker/1:2 Not tainted 6.16.0-rc4-g9773391cf4dd-dirty #36 PREEMPT(voluntary)
[ 21.673700] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[ 21.673700] Call Trace:
[ 21.673700] <TASK>
[ 21.673700] dump_stack_lvl+0x5f/0x80
[ 21.673700] print_report+0xd1/0x660
[ 21.673700] kasan_report+0xe5/0x120
[ 21.673700] __asan_report_store8_noabort+0x1b/0x30
[ 21.673700] asus_probe+0xeeb/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
[ 21.673700]
[ 21.673700] Allocated by task 54:
[ 21.673700] kasan_save_stack+0x3d/0x60
[ 21.673700] kasan_save_track+0x18/0x40
[ 21.673700] kasan_save_alloc_info+0x3b/0x50
[ 21.673700] __kasan_kmalloc+0x9c/0xa0
[ 21.673700] __kmalloc_cache_noprof+0x139/0x340
[ 21.673700] input_allocate_device+0x44/0x370
[ 21.673700] hidinput_connect+0xcb6/0x2630
[ 21.673700] hid_connect+0xf74/0x1d60
[ 21.673700] hid_hw_start+0x8c/0x110
[ 21.673700] asus_probe+0x5a3/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
[ 21.673700]
[ 21.673700] Freed by task 54:
[ 21.673700] kasan_save_stack+0x3d/0x60
[ 21.673700] kasan_save_track+0x18/0x40
[ 21.673700] kasan_save_free_info+0x3f/0x60
[ 21.673700] __kasan_slab_free+0x3c/0x50
[ 21.673700] kfree+0xcf/0x350
[ 21.673700] input_dev_release+0xab/0xd0
[ 21.673700] device_release+0x9f/0x220
[ 21.673700] kobject_put+0x12b/0x220
[ 21.673700] put_device+0x12/0x20
[ 21.673700] input_free_device+0x4c/0xb0
[ 21.673700] hidinput_connect+0x1862/0x2630
[ 21.673700] hid_connect+0xf74/0x1d60
[ 21.673700] hid_hw_start+0x8c/0x110
[ 21.673700] asus_probe+0x5a3/0xf80
[ 21.673700] hid_device_probe+0x2ee/0x700
[ 21.673700] really_probe+0x1c6/0x6b0
[ 21.673700] __driver_probe_device+0x24f/0x310
[ 21.673700] driver_probe_device+0x4e/0x220
[...]
Fixes: 9ce12d8be12c ("HID: asus: Add i2c touchpad support")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250810181041.44874-1-qasdev00@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2ca42f190b6714d6c481dfd3d9b62ea091c946b upstream.
hid_hw_raw_request() is actually useful to ensure the provided buffer
and length are valid. Directly calling in the low level transport driver
function bypassed those checks and allowed invalid paramto be used.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250710-report-size-null-v2-3-ccf922b7c4e5@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d0777ccaa2d46609d05b66ba0096802a2746193 upstream.
The low level transport driver expects the first byte to be the report
ID, even when the report ID is not use (in which case they just shift
the buffer).
However, __hid_request() whas not offsetting the buffer it used by one
in this case, meaning that the raw_request() callback emitted by the
transport driver would be stripped of the first byte.
Note: this changes the API for uhid devices when a request is made
through hid_hw_request. However, several considerations makes me think
this is fine:
- every request to a HID device made through hid_hw_request() would see
that change, but every request made through hid_hw_raw_request()
already has the new behaviour. So that means that the users are
already facing situations where they might have or not the first byte
being the null report ID when it is 0. We are making things more
straightforward in the end.
- uhid is mainly used for BLE devices
- uhid is also used for testing, but I don't see that change a big issue
- for BLE devices, we can check which kernel module is calling
hid_hw_request()
- and in those modules, we can check which are using a Bluetooth device
- and then we can check if the command is used with a report ID or not.
- surprise: none of the kernel module are using a report ID 0
- and finally, bluez, in its function set_report()[0], does the same
shift if the report ID is 0 and the given buffer has a size > 0.
[0] https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/profiles/input/hog-lib.c#n879
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/
Reported-by: syzbot+8258d5439c49d4c35f43@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=8258d5439c49d4c35f43
Tested-by: syzbot+8258d5439c49d4c35f43@syzkaller.appspotmail.com
Fixes: 4fa5a7f76cc7 ("HID: core: implement generic .request()")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250710-report-size-null-v2-2-ccf922b7c4e5@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f15ee98304b96e164ff2340e1dfd6181c3f42aa upstream.
When the report ID is not used, the low level transport drivers expect
the first byte to be 0. However, currently the allocated buffer not
account for that extra byte, meaning that instead of having 8 guaranteed
bytes for implement to be working, we only have 7.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20250710-report-size-null-v2-1-ccf922b7c4e5@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 54bae4c17c11688339eb73a04fd24203bb6e7494 ]
The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C)
report a HID sensor interface that is not actually implemented.
Attempting to access this non-functional sensor via iio_info causes
system hangs as runtime PM tries to wake up an unresponsive sensor.
Add these 2 devices to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a8953f4f7746c6a515989774fe03047c522c613 ]
MARTLINKTECHNOLOGY is a microphone device, when the HID interface in an
audio device is requested to get specific report id, the following error
may occur.
[ 562.939373] usb 1-1.4.1.2: new full-speed USB device number 21 using xhci_hcd
[ 563.104908] usb 1-1.4.1.2: New USB device found, idVendor=4c4a, idProduct=4155, bcdDevice= 1.00
[ 563.104910] usb 1-1.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 563.104911] usb 1-1.4.1.2: Product: USB Composite Device
[ 563.104912] usb 1-1.4.1.2: Manufacturer: SmartlinkTechnology
[ 563.104913] usb 1-1.4.1.2: SerialNumber: 20201111000001
[ 563.229499] input: SmartlinkTechnology USB Composite Device as /devices/pci0000:00/0000:00:07.1/0000:04:00.3/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1.2/1-1.4.1.2:1.2/0003:4C4A:4155.000F/input/input35
[ 563.291505] hid-generic 0003:4C4A:4155.000F: input,hidraw2: USB HID v2.01 Keyboard [SmartlinkTechnology USB Composite Device] on usb-0000:04:00.3-1.4.1.2/input2
[ 563.291557] usbhid 1-1.4.1.2:1.3: couldn't find an input interrupt endpoint
[ 568.506654] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 573.626656] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 578.746657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 583.866655] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 588.986657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
Ignore HID interface. The device is working properly.
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 85a720f4337f0ddf1603c8b75a8f1ffbbe022ef9 upstream.
When sysfs_create_files() fails in wacom_initialize_remotes() the error
is returned and the cleanup action will not have been registered yet.
As a result the kobject???s refcount is never dropped, so the
kobject can never be freed leading to a reference leak.
Fix this by calling kobject_put() before returning.
Fixes: 83e6b40e2de6 ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a19ae437ca5d5c7d9ec2678946fb339b1c706bf upstream.
When sysfs_create_files() fails during wacom_initialize_remotes() the
fifo buffer is not freed leading to a memory leak.
Fix this by calling kfifo_free() before returning.
Fixes: 83e6b40e2de6 ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ae416c5b1e2e816aee7b3fc8347adf70afabb4c upstream.
During wacom_initialize_remotes() a fifo buffer is allocated
with kfifo_alloc() and later a cleanup action is registered
during devm_add_action_or_reset() to clean it up.
However if the code fails to create a kobject and register it
with sysfs the code simply returns -ENOMEM before the cleanup
action is registered leading to a memory leak.
Fix this by ensuring the fifo is freed when the kobject creation
and registration process fails.
Fixes: 83e6b40e2de6 ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe7f7ac8e0c708446ff017453add769ffc15deed upstream.
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c19 ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fa9fdeea1b7d6440c22efa6d59a769eae8bc89f1 ]
This patch adds HID_QUIRK_ALWAYS_POLL for the ADATA XPG wireless gaming mouse (USB ID 125f:7505) and its USB dongle (USB ID 125f:7506). Without this quirk, the device does not generate input events properly.
Signed-off-by: Milton Barrera <miltonjosue2001@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d73a4bfa2881a6859b384b75a414c33d4898b055 ]
Since "LED_KANA" was defined as "0x04", the shift number should be "4".
Signed-off-by: junan <junan76@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22a05462c3d0eee15154faf8d13c49e6295270a5 ]
This function triggered a null pointer dereference if used to search for
a report that isn't implemented on the device. This happened both for
optional and required reports alike.
The same logic was applied to pidff_find_special_field and although
pidff_init_fields should return an error earlier if one of the required
reports is missing, future modifications could change this logic and
resurface this possible null pointer dereference again.
LKML bug report:
https://lore.kernel.org/all/CAL-gK7f5=R0nrrQdPtaZZr1fd-cdAMbDMuZ_NLA8vM0SX+nGSw@mail.gmail.com
Reported-by: Nolan Nicholson <nolananicholson@gmail.com>
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8876fc1884f5b39550c8387ff3176396c988541d ]
Envelope struct is always initialized, but the envelope itself is
optional as described in USB PID Device class definition 1.0.
5.1.1.1 Type Specific Block Offsets
...
4) Effects that do not use Condition Blocks use 1 Parameter Block and
an *optional* Envelope Block.
Sending out "empty" envelope breaks force feedback on some devices with
games that use SINE effect + offset to emulate constant force effect, as
well as generally breaking Constant/Periodic effects. One of the affected
brands is Moza Racing.
This change prevents the envelope from being sent if it contains all
0 values while keeping the old behavior of only sending it, if it differs
from the old one.
Changes in v6:
- Simplify the checks to make them clearer
- Fix possible null pointer dereference while calling
pidff_needs_set_envelope
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37e0591fe44dce39d1ebc7a82d5b6e4dba1582eb ]
Software uses 0 as de-facto infinite lenght on Linux FF apis (SDL),
Linux doesn't actually define anythi as of now, while USB PID defines
NULL (0xffff). Most PID devices do not expect a 0-length effect and
can't interpret it as infinite. This change fixes Force Feedback for
most PID compliant devices.
As most games depend on updating the values of already playing infinite
effects, this is crucial to ensure they will actually work.
Previously, users had to rely on third-party software to do this conversion
and make their PID devices usable.
Co-developed-by: Makarenko Oleg <oleg@makarenk.ooo>
Signed-off-by: Makarenko Oleg <oleg@makarenk.ooo>
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com>
Reviewed-by: Michał Kopeć <michal@nozomi.space>
Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Paul Dino Jones <paul@spacefreak18.xyz>
Tested-by: Cristóferson Bueno <cbueno81@gmail.com>
Tested-by: Pablo Cisneros <patchkez@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9821709af892be9fbf4ee9a50b2f3e0604295ce0 upstream.
Add mapping for headset mute key events.
Remove PLT_QUIRK_DOUBLE_VOLUME_KEYS quirk and made it generic.
The quirk logic did not keep track of the actual previous key
so any key event occurring in less than or equal to 5ms was ignored.
Remove PLT_QUIRK_FOLLOWED_OPPOSITE_VOLUME_KEYS quirk.
It had the same logic issue as the double key quirk and was actually
masking the as designed behavior of most of the headsets.
It's occurrence should be minimized with the ALSA control naming
quirk that is part of the patch set.
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 363236d709e75610b628c2a4337ccbe42e454b6d ]
The HP 5MP Camera (USB ID 0408:5473) reports a HID sensor interface that
is not actually implemented. Attempting to access this non-functional
sensor via iio_info causes system hangs as runtime PM tries to wake up
an unresponsive sensor.
[453] hid-sensor-hub 0003:0408:5473.0003: Report latency attributes: ffffffff:ffffffff
[453] hid-sensor-hub 0003:0408:5473.0003: common attributes: 5:1, 2:1, 3:1 ffffffff:ffffffff
Add this device to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b54ae69197b9f416baa0fceadff7e89075f8454 ]
The timestamps in the Firmware log and HID sensor samples are incorrect.
They show 1970-01-01 because the current IPC driver only uses the first
8 bytes of bootup time when synchronizing time with the firmware. The
firmware converts the bootup time to UTC time, which results in the
display of 1970-01-01.
In write_ipc_from_queue(), when sending the MNG_SYNC_FW_CLOCK message,
the clock is updated according to the definition of ipc_time_update_msg.
However, in _ish_sync_fw_clock(), the message length is specified as the
size of uint64_t when building the doorbell. As a result, the firmware
only receives the first 8 bytes of struct ipc_time_update_msg.
This patch corrects the length in the doorbell to ensure the entire
ipc_time_update_msg is sent, fixing the timestamp issue.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07583a0010696a17fb0942e0b499a62785c5fc9f ]
The system can experience a random crash a few minutes after the driver is
removed. This issue occurs due to improper handling of memory freeing in
the ishtp_hid_remove() function.
The function currently frees the `driver_data` directly within the loop
that destroys the HID devices, which can lead to accessing freed memory.
Specifically, `hid_destroy_device()` uses `driver_data` when it calls
`hid_ishtp_set_feature()` to power off the sensor, so freeing
`driver_data` beforehand can result in accessing invalid memory.
This patch resolves the issue by storing the `driver_data` in a temporary
variable before calling `hid_destroy_device()`, and then freeing the
`driver_data` after the device is destroyed.
Fixes: 0b28cb4bcb17 ("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4bd0725c09f377ffaf22b834241f6c050742e4fc ]
As reported by the kernel test robot, the following warning occurs:
>> drivers/hid/hid-google-hammer.c:261:36: warning: 'cbas_ec_acpi_ids' defined but not used [-Wunused-const-variable=]
261 | static const struct acpi_device_id cbas_ec_acpi_ids[] = {
| ^~~~~~~~~~~~~~~~
The 'cbas_ec_acpi_ids' array is only used when CONFIG_ACPI is enabled.
Wrapping its definition and 'MODULE_DEVICE_TABLE' in '#ifdef CONFIG_ACPI'
prevents a compiler warning when ACPI is disabled.
Fixes: eb1aac4c8744f75 ("HID: google: add support tablet mode switch for Whiskers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201141.jctFH5eB-lkp@intel.com/
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2ff5baa9b5275e3acafdf7f2089f74cccb2f38d1 upstream.
Syzkaller reports a NULL pointer dereference issue in input_event().
BUG: KASAN: null-ptr-deref in instrument_atomic_read include/linux/instrumented.h:68 [inline]
BUG: KASAN: null-ptr-deref in _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
BUG: KASAN: null-ptr-deref in is_event_supported drivers/input/input.c:67 [inline]
BUG: KASAN: null-ptr-deref in input_event+0x42/0xa0 drivers/input/input.c:395
Read of size 8 at addr 0000000000000028 by task syz-executor199/2949
CPU: 0 UID: 0 PID: 2949 Comm: syz-executor199 Not tainted 6.13.0-rc4-syzkaller-00076-gf097a36ef88d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
kasan_report+0xd9/0x110 mm/kasan/report.c:602
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189
instrument_atomic_read include/linux/instrumented.h:68 [inline]
_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
is_event_supported drivers/input/input.c:67 [inline]
input_event+0x42/0xa0 drivers/input/input.c:395
input_report_key include/linux/input.h:439 [inline]
key_down drivers/hid/hid-appleir.c:159 [inline]
appleir_raw_event+0x3e5/0x5e0 drivers/hid/hid-appleir.c:232
__hid_input_report.constprop.0+0x312/0x440 drivers/hid/hid-core.c:2111
hid_ctrl+0x49f/0x550 drivers/hid/usbhid/hid-core.c:484
__usb_hcd_giveback_urb+0x389/0x6e0 drivers/usb/core/hcd.c:1650
usb_hcd_giveback_urb+0x396/0x450 drivers/usb/core/hcd.c:1734
dummy_timer+0x17f7/0x3960 drivers/usb/gadget/udc/dummy_hcd.c:1993
__run_hrtimer kernel/time/hrtimer.c:1739 [inline]
__hrtimer_run_queues+0x20a/0xae0 kernel/time/hrtimer.c:1803
hrtimer_run_softirq+0x17d/0x350 kernel/time/hrtimer.c:1820
handle_softirqs+0x206/0x8d0 kernel/softirq.c:561
__do_softirq kernel/softirq.c:595 [inline]
invoke_softirq kernel/softirq.c:435 [inline]
__irq_exit_rcu+0xfa/0x160 kernel/softirq.c:662
irq_exit_rcu+0x9/0x30 kernel/softirq.c:678
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1049 [inline]
sysvec_apic_timer_interrupt+0x90/0xb0 arch/x86/kernel/apic/apic.c:1049
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1a/0x20 arch/x86/include/asm/idtentry.h:702
__mod_timer+0x8f6/0xdc0 kernel/time/timer.c:1185
add_timer+0x62/0x90 kernel/time/timer.c:1295
schedule_timeout+0x11f/0x280 kernel/time/sleep_timeout.c:98
usbhid_wait_io+0x1c7/0x380 drivers/hid/usbhid/hid-core.c:645
usbhid_init_reports+0x19f/0x390 drivers/hid/usbhid/hid-core.c:784
hiddev_ioctl+0x1133/0x15b0 drivers/hid/usbhid/hiddev.c:794
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:906 [inline]
__se_sys_ioctl fs/ioctl.c:892 [inline]
__x64_sys_ioctl+0x190/0x200 fs/ioctl.c:892
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
This happens due to the malformed report items sent by the emulated device
which results in a report, that has no fields, being added to the report list.
Due to this appleir_input_configured() is never called, hidinput_connect()
fails which results in the HID_CLAIMED_INPUT flag is not being set. However,
it does not make appleir_probe() fail and lets the event callback to be
called without the associated input device.
Thus, add a check for the HID_CLAIMED_INPUT flag and leave the event hook
early if the driver didn't claim any input_dev for some reason. Moreover,
some other hid drivers accessing input_dev in their event callbacks do have
similar checks, too.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9a4a5574ce42 ("HID: appleir: add support for Apple ir devices")
Cc: stable@vger.kernel.org
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9b8e2220d3a052a690b1d1b23019673e612494c5 ]
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in mt_input_configured() is not checked.
Add NULL check in mt_input_configured(), to handle kernel NULL
pointer dereference error.
Fixes: 479439463529 ("HID: multitouch: Correct devm device reference for hidinput input_dev name")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8a5b38c3fd709e8acd2bfdedf66c25e6af759576 upstream.
The hid-sensor-hub creates the individual device structs and transfers them
to the created mfd platform-devices via the platform_data in the mfd_cell.
Before e651a1da442a ("HID: hid-sensor-hub: Allow parallel synchronous reads")
the sensor-hub was managing access centrally, with one "completion" in the
hub's data structure, which needed to be finished on removal at the latest.
The mentioned commit then moved this central management to each hid sensor
device, resulting on a completion in each struct hid_sensor_hub_device.
The remove procedure was adapted to go through all sensor devices and
finish any pending "completion".
What this didn't take into account was, platform_device_add_data() that is
used by mfd_add{_hotplug}_devices() does a kmemdup on the submitted
platform-data. So the data the platform-device gets is a copy of the
original data, meaning that the device worked on a different completion
than what sensor_hub_remove() currently wants to access.
To fix that, use device_for_each_child() to go through each child-device
similar to how mfd_remove_devices() unregisters the devices later and
with that get the live platform_data to finalize the correct completion.
Fixes: e651a1da442a ("HID: hid-sensor-hub: Allow parallel synchronous reads")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://lore.kernel.org/r/20241107114712.538976-2-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c4c123504a65583e3689b3de04a61dc5272e453a ]
Add PCI device ID of wacom device into driver support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Tested-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Collections
commit 64f2657b579343cf923aa933f08074e6258eb07b upstream.
A report in 2019 by the syzbot fuzzer was found to be connected to two
errors in the HID core associated with Resolution Multipliers. One of
the errors was fixed by commit ea427a222d8b ("HID: core: Fix deadloop
in hid_apply_multiplier."), but the other has not been fixed.
This error arises because hid_apply_multipler() assumes that every
Resolution Multiplier control is contained in a Logical Collection,
i.e., there's no way the routine can ever set multiplier_collection to
NULL. This is in spite of the fact that the function starts with a
big comment saying:
* "The Resolution Multiplier control must be contained in the same
* Logical Collection as the control(s) to which it is to be applied.
...
* If no Logical Collection is
* defined, the Resolution Multiplier is associated with all
* controls in the report."
* HID Usage Table, v1.12, Section 4.3.1, p30
*
* Thus, search from the current collection upwards until we find a
* logical collection...
The comment and the code overlook the possibility that none of the
collections found may be a Logical Collection.
The fix is to set the multiplier_collection pointer to NULL if the
collection found isn't a Logical Collection.
Reported-by: syzbot+ec5f884c4a135aa0dbb9@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000109c040597dc5843@google.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Peter Hutterer <peter.hutterer@who-t.net>
Fixes: 5a4abb36f312 ("HID: core: process the Resolution Multiplier")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59548215b76be98cf3422eea9a67d6ea578aca3d upstream.
Due to incorrect dev->product reporting by certain devices, null
pointer dereferences occur when dev->product is empty, leading to
potential system crashes.
This issue was found on EXCELSIOR DL37-D05 device with
Loongson-LS3A6000-7A2000-DL37 motherboard.
Kernel logs:
[ 56.470885] usb 4-3: new full-speed USB device number 4 using ohci-pci
[ 56.671638] usb 4-3: string descriptor 0 read error: -22
[ 56.671644] usb 4-3: New USB device found, idVendor=056a, idProduct=0374, bcdDevice= 1.07
[ 56.671647] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 56.678839] hid-generic 0003:056A:0374.0004: hiddev0,hidraw3: USB HID v1.10 Device [HID 056a:0374] on usb-0000:00:05.0-3/input0
[ 56.697719] CPU 2 Unable to handle kernel paging request at virtual address 0000000000000000, era == 90000000066e35c8, ra == ffff800004f98a80
[ 56.697732] Oops[#1]:
[ 56.697734] CPU: 2 PID: 2742 Comm: (udev-worker) Tainted: G OE 6.6.0-loong64-desktop #25.00.2000.015
[ 56.697737] Hardware name: Inspur CE520L2/C09901N000000000, BIOS 2.09.00 10/11/2024
[ 56.697739] pc 90000000066e35c8 ra ffff800004f98a80 tp 9000000125478000 sp 900000012547b8a0
[ 56.697741] a0 0000000000000000 a1 ffff800004818b28 a2 0000000000000000 a3 0000000000000000
[ 56.697743] a4 900000012547b8f0 a5 0000000000000000 a6 0000000000000000 a7 0000000000000000
[ 56.697745] t0 ffff800004818b2d t1 0000000000000000 t2 0000000000000003 t3 0000000000000005
[ 56.697747] t4 0000000000000000 t5 0000000000000000 t6 0000000000000000 t7 0000000000000000
[ 56.697748] t8 0000000000000000 u0 0000000000000000 s9 0000000000000000 s0 900000011aa48028
[ 56.697750] s1 0000000000000000 s2 0000000000000000 s3 ffff800004818e80 s4 ffff800004810000
[ 56.697751] s5 90000001000b98d0 s6 ffff800004811f88 s7 ffff800005470440 s8 0000000000000000
[ 56.697753] ra: ffff800004f98a80 wacom_update_name+0xe0/0x300 [wacom]
[ 56.697802] ERA: 90000000066e35c8 strstr+0x28/0x120
[ 56.697806] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 56.697816] PRMD: 0000000c (PPLV0 +PIE +PWE)
[ 56.697821] EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[ 56.697827] ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
[ 56.697831] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 56.697835] BADV: 0000000000000000
[ 56.697836] PRID: 0014d000 (Loongson-64bit, Loongson-3A6000)
[ 56.697838] Modules linked in: wacom(+) bnep bluetooth rfkill qrtr nls_iso8859_1 nls_cp437 snd_hda_codec_conexant snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_timer snd soundcore input_leds mousedev led_class joydev deepin_netmonitor(OE) fuse nfnetlink dmi_sysfs ip_tables x_tables overlay amdgpu amdxcp drm_exec gpu_sched drm_buddy radeon drm_suballoc_helper i2c_algo_bit drm_ttm_helper r8169 ttm drm_display_helper spi_loongson_pci xhci_pci cec xhci_pci_renesas spi_loongson_core hid_generic realtek gpio_loongson_64bit
[ 56.697887] Process (udev-worker) (pid: 2742, threadinfo=00000000aee0d8b4, task=00000000a9eff1f3)
[ 56.697890] Stack : 0000000000000000 ffff800004817e00 0000000000000000 0000251c00000000
[ 56.697896] 0000000000000000 00000011fffffffd 0000000000000000 0000000000000000
[ 56.697901] 0000000000000000 1b67a968695184b9 0000000000000000 90000001000b98d0
[ 56.697906] 90000001000bb8d0 900000011aa48028 0000000000000000 ffff800004f9d74c
[ 56.697911] 90000001000ba000 ffff800004f9ce58 0000000000000000 ffff800005470440
[ 56.697916] ffff800004811f88 90000001000b98d0 9000000100da2aa8 90000001000bb8d0
[ 56.697921] 0000000000000000 90000001000ba000 900000011aa48028 ffff800004f9d74c
[ 56.697926] ffff8000054704e8 90000001000bb8b8 90000001000ba000 0000000000000000
[ 56.697931] 90000001000bb8d0 9000000006307564 9000000005e666e0 90000001752359b8
[ 56.697936] 9000000008cbe400 900000000804d000 9000000005e666e0 0000000000000000
[ 56.697941] ...
[ 56.697944] Call Trace:
[ 56.697945] [<90000000066e35c8>] strstr+0x28/0x120
[ 56.697950] [<ffff800004f98a80>] wacom_update_name+0xe0/0x300 [wacom]
[ 56.698000] [<ffff800004f9ce58>] wacom_parse_and_register+0x338/0x900 [wacom]
[ 56.698050] [<ffff800004f9d74c>] wacom_probe+0x32c/0x420 [wacom]
[ 56.698099] [<9000000006307564>] hid_device_probe+0x144/0x260
[ 56.698103] [<9000000005e65d68>] really_probe+0x208/0x540
[ 56.698109] [<9000000005e661dc>] __driver_probe_device+0x13c/0x1e0
[ 56.698112] [<9000000005e66620>] driver_probe_device+0x40/0x100
[ 56.698116] [<9000000005e6680c>] __device_attach_driver+0x12c/0x180
[ 56.698119] [<9000000005e62bc8>] bus_for_each_drv+0x88/0x160
[ 56.698123] [<9000000005e66468>] __device_attach+0x108/0x260
[ 56.698126] [<9000000005e63918>] device_reprobe+0x78/0x100
[ 56.698129] [<9000000005e62a68>] bus_for_each_dev+0x88/0x160
[ 56.698132] [<9000000006304e54>] __hid_bus_driver_added+0x34/0x80
[ 56.698134] [<9000000005e62bc8>] bus_for_each_drv+0x88/0x160
[ 56.698137] [<9000000006304df0>] __hid_register_driver+0x70/0xa0
[ 56.698142] [<9000000004e10fe4>] do_one_initcall+0x104/0x320
[ 56.698146] [<9000000004f38150>] do_init_module+0x90/0x2c0
[ 56.698151] [<9000000004f3a3d8>] init_module_from_file+0xb8/0x120
[ 56.698155] [<9000000004f3a590>] idempotent_init_module+0x150/0x3a0
[ 56.698159] [<9000000004f3a890>] sys_finit_module+0xb0/0x140
[ 56.698163] [<900000000671e4e8>] do_syscall+0x88/0xc0
[ 56.698166] [<9000000004e12404>] handle_syscall+0xc4/0x160
[ 56.698171] Code: 0011958f 00150224 5800cd85 <2a00022c> 00150004 4000c180 0015022c 03400000 03400000
[ 56.698192] ---[ end trace 0000000000000000 ]---
Fixes: 09dc28acaec7 ("HID: wacom: Improve generic name generation")
Reported-by: Zhenxing Chen <chenzhenxing@uniontech.com>
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://patch.msgid.link/B31757FE8E1544CF+20241125052616.18261-1-wangyuli@uniontech.com
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49a397ad24ee5e2c53a59dada2780d7e71bd3f77 upstream.
The tilt data contained in the Bluetooth packets of an Intuos Pro are
supposed to be interpreted as signed values. Simply casting the values
to type `char` is not guaranteed to work since it is implementation-
defined whether it is signed or unsigned. At least one user has noticed
the data being reported incorrectly on their system. To ensure that the
data is interpreted properly, we specifically cast to `signed char`
instead.
Link: https://github.com/linuxwacom/input-wacom/issues/445
Fixes: 4922cd26f03c ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
CC: stable@vger.kernel.org # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7a5ab8071114344f62a8b1e64ed3452a77257d76 ]
The behavior of HONOR MagicBook Art 14 touchpad is not consistent
after reboots, as sometimes it reports itself as a touchpad, and
sometimes as a mouse.
Similarly to GLO-GXXX it is possible to call MT_QUIRK_FORCE_GET_FEATURE as a
workaround to force set feature in mt_set_input_mode() for such special touchpad
device.
[jkosina@suse.com: reword changelog a little bit]
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/1040
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 177f25d1292c7e16e1199b39c85480f7f8815552 ]
Since the report buffer is used by all kinds of drivers in various ways, let's
zero-initialize it during allocation to make sure that it can't be ever used
to leak kernel memory via specially-crafted report.
Fixes: 27ce405039bf ("HID: fix data access in implement()")
Reported-by: Benoît Sevens <bsevens@google.com>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d41bff05a61fb539f21e9bf0d39fac77f457434e upstream.
Fix the uninitialized symbol 'rv' in the function ish_fw_xfer_direct_dma
to resolve the following warning from the smatch tool:
drivers/hid/intel-ish-hid/ishtp-fw-loader.c:714 ish_fw_xfer_direct_dma()
error: uninitialized symbol 'rv'.
Initialize 'rv' to 0 to prevent undefined behavior from uninitialized
access.
Cc: stable@vger.kernel.org
Fixes: 91b228107da3 ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: SurajSonawane2415 <surajsonawane0215@gmail.com>
Link: https://patch.msgid.link/20241004075944.44932-1-surajsonawane0215@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
