| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit a66c5ed539277b9f2363bbace0dba88b85b36c26 ]
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit cdc5287acad9ede121924a9c9313544b80d15842 upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fce15c45d3fbd9fc1feaaf3210d8e3f8b33dfd3a ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb383 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dbd3e6eaf3d813939b28e8a66e29d81cdc836445 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503f3 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ada61aa0b1184a8fda1a89a340c7d6cc4e59aee5 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce189 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ae59dc455a78fb73034dd1fbb337d7e59c27cbd8 upstream.
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6a1 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc9f ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 724e8af85854c4d3401313b6dd7d79cf792d8990 ]
Old code produces -24999 for 0b1110011100000000 input in standard format due to
always rounding up rather than "away from zero".
Use the common macro for division, unify and simplify the conversion code along
the way.
Fixes: 9410700b881f ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-3-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbbf244f0515af3472084f22b6213121b4a63835 ]
Fans 7..12 do not have their own set of configuration registers.
So far the code ignored that and read beyond the end of the configuration
register range to get the tachometer period. This resulted in more or less
random fan speed values for those fans.
The datasheet is quite vague when it comes to defining the tachometer
period for fans 7..12. Experiments confirm that the period is the same
for both fans associated with a given set of configuration registers.
Fixes: 54187ff9d766 ("hwmon: (max31790) Convert to use new hwmon registration API")
Fixes: 195a4b4298a7 ("hwmon: Driver for Maxim MAX31790")
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210526154022.3223012-2-linux@roeck-us.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97387c2f06bcfd79d04a848d35517b32ee6dca7c ]
Valid Maxim Integrated ACPI device IDs would start with MXIM,
not with MAX1. On top of that, ACPI device IDs reflecting chip names
are almost always invalid.
Remove the invalid ACPI IDs.
Fixes: 04e1e70afec6 ("hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 99ae3417672a6d4a3bf68d4fc43d7c6ca074d477 upstream.
This reverts commit 9aa3aa15f4c2f74f47afd6c5db4b420fadf3f315.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu>
Fixes: 9aa3aa15f4c2 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe")
Cc: stable <stable@vger.kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62456189f3292c62f87aef363f204886dc1d4b48 upstream.
max6658 may report unrealistically high temperature during
the driver initialization, for which, its overtemp alarm pin
also gets asserted. For certain devices implementing overtemp
protection based on that pin, it may further trigger a reset to
the device. By reproducing the problem, the wrong reading is
found to be coincident with changing the conversion rate.
To mitigate this issue, set the stop bit before changing the
conversion rate and unset it thereafter. After such change, the
wrong reading is not reproduced. Apply this change only to the
max6657 kind for now, controlled by flag LM90_PAUSE_ON_CONFIG.
Signed-off-by: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cecf7560f00a8419396a2ed0f6e5d245ccb4feac ]
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 14b0e83dc4f1e52b94acaeb85a18fd7fdd46d2dc upstream.
This patch fixes a bug which does not let FAN mode to be changed from
sysfs(pwm1_enable). i.e pwm1_enable can not be set to 3, it will always
remain at 0.
This is caused because the device driver handles the result of
"read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg)" incorrectly. The
driver thinks an error has occurred if the (result != 0). This has been
fixed by changing the condition to (result < 0).
Signed-off-by: Vishwas M <vishwas.reddy.vr@gmail.com>
Link: https://lore.kernel.org/r/20200707142747.118414-1-vishwas.reddy.vr@gmail.com
Fixes: 9df7305b5a86 ("hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8b97f9922211c44a739c5cbd9502ecbb9f17f6d1 ]
Although it rarely happens, we should call free_capabilities()
if error happens after read_capabilities() to free allocated strings.
Fixes: de584afa5e188 ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Link: https://lore.kernel.org/r/20200625043242.31175-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 016983d138cbe99a5c0aaae0103ee88f5300beb3 ]
Per the datasheet for max6697, OVERT mask and ALERT mask are different.
For example, the 7th bit of OVERT is the local channel but for alert
mask, the 6th bit is the local channel. Therefore, we can't apply the
same mask for both registers. In addition to that, the max6697 driver
is supposed to be compatibale with different models. I manually went over
all the listed chips and made sure all chip types have the same layout.
Testing;
mask value of 0x9 should map to 0x44 for ALERT and 0x84 for OVERT.
I used iotool to read the reg value back to verify. I only tested this
change on max6581.
Reference:
https://datasheets.maximintegrated.com/en/ds/MAX6581.pdf
https://datasheets.maximintegrated.com/en/ds/MAX6697.pdf
https://datasheets.maximintegrated.com/en/ds/MAX6699.pdf
Signed-off-by: Chu Lin <linchuyuan@google.com>
Fixes: 5372d2d71c46e ("hwmon: Driver for Maxim MAX6697 and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c843b382e61b5f28a3d917712c69a344f632387c ]
The jc42 driver passes I2C client's name as hwmon device name. In case
of device tree probed devices this ends up being part of the compatible
string, "jc-42.4-temp". This name contains hyphens and the hwmon core
doesn't like this:
jc42 2-0018: hwmon: 'jc-42.4-temp' is not a valid name attribute, please fix
This changes the name to "jc42" which doesn't have any illegal
characters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200417092853.31206-1-s.hauer@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 44f2f882909fedfc3a56e4b90026910456019743 upstream.
This is only called from adt7462_update_device(). The caller expects it
to return zero on error. I fixed a similar issue earlier in commit
a4bf06d58f21 ("hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0")
but I missed this one.
Fixes: c0b4e3ab0c76 ("adt7462: new hwmon driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20200303101608.kqjwfcazu2ylhi2a@kili.mountain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf2b012c90e74e85d8aea7d67e48868069cfee0c upstream.
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7713e62c8623c54dac88d1fa724aa487a38c3efb upstream.
in0 thresholds are written to the in2 thresholds registers
in2 thresholds to in3 thresholds
in3 thresholds to in4 thresholds
in4 thresholds to in0 thresholds
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f509.rc0oEvPOMjbfPW1w%gilles.buloz@kontron.com
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bf8bdcf3bada771eb12b57f2a30caee69e8ab8d upstream.
The hwmon core uses device managed functions, tied to the hwmon parent
device, for various internal memory allocations. This is problematic
since hwmon device lifetime does not necessarily match its parent's
device lifetime. If there is a mismatch, memory leaks will accumulate
until the parent device is released.
Fix the problem by managing all memory allocations internally. The only
exception is memory allocation for thermal device registration, which
can be tied to the hwmon device, along with thermal device registration
itself.
Fixes: d560168b5d0f ("hwmon: (core) New hwmon registration API")
Cc: stable@vger.kernel.org # v4.14.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.14.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9.x: 3a412d5e4a1c: hwmon: (core) Simplify sysfs attribute name allocation
Cc: stable@vger.kernel.org # v4.9.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.9.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9+
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74e3512731bd5c9673176425a76a7cc5efa8ddb6 upstream.
Fix double-free that happens when thermal zone setup fails, see KASAN log
below.
==================================================================
BUG: KASAN: double-free or invalid-free in __hwmon_device_register+0x5dc/0xa7c
CPU: 0 PID: 132 Comm: kworker/0:2 Tainted: G B 4.19.0-rc8-next-20181016-00042-gb52cd80401e9-dirty #41
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
Backtrace:
[<c0110540>] (dump_backtrace) from [<c0110944>] (show_stack+0x20/0x24)
[<c0110924>] (show_stack) from [<c105cb08>] (dump_stack+0x9c/0xb0)
[<c105ca6c>] (dump_stack) from [<c02fdaec>] (print_address_description+0x68/0x250)
[<c02fda84>] (print_address_description) from [<c02fd4ac>] (kasan_report_invalid_free+0x68/0x88)
[<c02fd444>] (kasan_report_invalid_free) from [<c02fc85c>] (__kasan_slab_free+0x1f4/0x200)
[<c02fc668>] (__kasan_slab_free) from [<c02fd0c0>] (kasan_slab_free+0x14/0x18)
[<c02fd0ac>] (kasan_slab_free) from [<c02f9c6c>] (kfree+0x90/0x294)
[<c02f9bdc>] (kfree) from [<c0b41bbc>] (__hwmon_device_register+0x5dc/0xa7c)
[<c0b415e0>] (__hwmon_device_register) from [<c0b421e8>] (hwmon_device_register_with_info+0xa0/0xa8)
[<c0b42148>] (hwmon_device_register_with_info) from [<c0b42324>] (devm_hwmon_device_register_with_info+0x74/0xb4)
[<c0b422b0>] (devm_hwmon_device_register_with_info) from [<c0b4481c>] (lm90_probe+0x414/0x578)
[<c0b44408>] (lm90_probe) from [<c0aeeff4>] (i2c_device_probe+0x35c/0x384)
[<c0aeec98>] (i2c_device_probe) from [<c08776cc>] (really_probe+0x290/0x3e4)
[<c087743c>] (really_probe) from [<c0877a2c>] (driver_probe_device+0x80/0x1c4)
[<c08779ac>] (driver_probe_device) from [<c0877da8>] (__device_attach_driver+0x104/0x11c)
[<c0877ca4>] (__device_attach_driver) from [<c0874dd8>] (bus_for_each_drv+0xa4/0xc8)
[<c0874d34>] (bus_for_each_drv) from [<c08773b0>] (__device_attach+0xf0/0x15c)
[<c08772c0>] (__device_attach) from [<c0877e24>] (device_initial_probe+0x1c/0x20)
[<c0877e08>] (device_initial_probe) from [<c08762f4>] (bus_probe_device+0xdc/0xec)
[<c0876218>] (bus_probe_device) from [<c0876a08>] (deferred_probe_work_func+0xa8/0xd4)
[<c0876960>] (deferred_probe_work_func) from [<c01527c4>] (process_one_work+0x3dc/0x96c)
[<c01523e8>] (process_one_work) from [<c01541e0>] (worker_thread+0x4ec/0x8bc)
[<c0153cf4>] (worker_thread) from [<c015b238>] (kthread+0x230/0x240)
[<c015b008>] (kthread) from [<c01010bc>] (ret_from_fork+0x14/0x38)
Exception stack(0xcf743fb0 to 0xcf743ff8)
3fa0: 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Allocated by task 132:
kasan_kmalloc.part.1+0x58/0xf4
kasan_kmalloc+0x90/0xa4
kmem_cache_alloc_trace+0x90/0x2a0
__hwmon_device_register+0xbc/0xa7c
hwmon_device_register_with_info+0xa0/0xa8
devm_hwmon_device_register_with_info+0x74/0xb4
lm90_probe+0x414/0x578
i2c_device_probe+0x35c/0x384
really_probe+0x290/0x3e4
driver_probe_device+0x80/0x1c4
__device_attach_driver+0x104/0x11c
bus_for_each_drv+0xa4/0xc8
__device_attach+0xf0/0x15c
device_initial_probe+0x1c/0x20
bus_probe_device+0xdc/0xec
deferred_probe_work_func+0xa8/0xd4
process_one_work+0x3dc/0x96c
worker_thread+0x4ec/0x8bc
kthread+0x230/0x240
ret_from_fork+0x14/0x38
(null)
Freed by task 132:
__kasan_slab_free+0x12c/0x200
kasan_slab_free+0x14/0x18
kfree+0x90/0x294
hwmon_dev_release+0x1c/0x20
device_release+0x4c/0xe8
kobject_put+0xac/0x11c
device_unregister+0x2c/0x30
__hwmon_device_register+0xa58/0xa7c
hwmon_device_register_with_info+0xa0/0xa8
devm_hwmon_device_register_with_info+0x74/0xb4
lm90_probe+0x414/0x578
i2c_device_probe+0x35c/0x384
really_probe+0x290/0x3e4
driver_probe_device+0x80/0x1c4
__device_attach_driver+0x104/0x11c
bus_for_each_drv+0xa4/0xc8
__device_attach+0xf0/0x15c
device_initial_probe+0x1c/0x20
bus_probe_device+0xdc/0xec
deferred_probe_work_func+0xa8/0xd4
process_one_work+0x3dc/0x96c
worker_thread+0x4ec/0x8bc
kthread+0x230/0x240
ret_from_fork+0x14/0x38
(null)
Cc: <stable@vger.kernel.org> # v4.15+
Fixes: 47c332deb8e8 ("hwmon: Deal with errors from the thermal subsystem")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47c332deb8e89f6c59b0bb2615945c6e7fad1a60 upstream.
If the thermal subsystem returne -EPROBE_DEFER or any other error
when hwmon calls devm_thermal_zone_of_sensor_register(), this is
silently ignored.
I ran into this with an incorrectly defined thermal zone, making
it non-existing and thus this call failed with -EPROBE_DEFER
assuming it would appear later. The sensor was still added
which is incorrect: sensors must strictly be added after the
thermal zones, so deferred probe must be respected.
Fixes: d560168b5d0f ("hwmon: (core) New hwmon registration API")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a412d5e4a1c831723d0aaf305f1cf9a78ad9c90 upstream.
Allocating the sysfs attribute name only if needed and only with the
required minimum length looks optimal, but does not take the additional
overhead for both devm_ data structures and the allocation header itself
into account. This also results in unnecessary memory fragmentation.
Move the sysfs name string into struct hwmon_device_attribute and give it
a sufficient length to reduce this overhead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf3ca1877574a306c0207cbf7fdf25419d9229df upstream.
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fdc7d8e829ec755c5cfb2f5a8d8c0cdfb664f895 ]
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.
Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7d82fcc9d9e81241778aaa22fda7be753e237d86 ]
Writes into limit registers fail if the temperature written is negative.
The regmap write operation checks the value range, regmap_write accepts
an unsigned int as parameter, and the temperature value passed to
regmap_write is kept in a variable declared as long. Negative values
are converted large unsigned integers, which fails the range check.
Fix by type casting the temperature to u16 when calling regmap_write().
Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Fixes: e65365fed87f ("hwmon: (lm75) Convert to use regmap")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e95fd518d05bfc087da6fcdea4900a57cfb083bd ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: b72656dbc491 ("hwmon: (w83627hf) Stop using globals for I/O port numbers")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 791ebc9d34e9d212fc03742c31654b017d385926 ]
The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.
So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f67f7583e77fe5dc57aab3a6159c2642544eaad ]
Probe deferrals aren't actual errors, so silence the error message in
case the PWM cannot yet be acquired.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e4d91aa071810deac2cd052161aefb376ecf04e ]
At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.
While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.
The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.
Signed-off-by: Wang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 38ada2f406a9b81fb1249c5c9227fa657e7d5671 upstream.
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.
In detail:
- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.
Fix is_visible function to detect and report in4_input visibility
as expected.
Reported-by: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: Gilles Buloz <Gilles.Buloz@kontron.com>
Cc: stable@vger.kernel.org
Fixes: 3434f37835804 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3d43e2e45fd9d44ba52d20debd12cd4ee9c89bf ]
Fixed address of third NCT6106_REG_WEIGHT_DUTY_STEP, and
added missed NCT6106_REG_TOLERANCE_H.
Fixes: 6c009501ff200 ("hwmon: (nct6775) Add support for NCT6102D/6106D")
Signed-off-by: Bjoern Gerhart <gerhart@posteo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4a60570dce658e3f8885bbcf852430b99f65aca5 ]
Some chips have attributes which exist on more than one page but the
attribute is not presently marked as paged. This causes the attributes
to be generated with the same label, which makes it impossible for
userspace to tell them apart.
Marking all such attributes as paged would result in the page suffix
being added regardless of whether they were present on more than one
page or not, which might break existing setups. Therefore, we add a
second check which treats the attribute as paged, even if not marked as
such, if it is present on multiple pages.
Fixes: b4ce237b7f7d ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 73e6ff71a7ea924fb7121d576a2d41e3be3fc6b5 ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Unable to handle kernel paging request at virtual address ffffffbffee0002e
pgd = ffffffc1d68d4000
[ffffffbffee0002e] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 94000046 [#1] PREEMPT SMP
Modules linked in: f71805f(+) hwmon
CPU: 3 PID: 1659 Comm: insmod Not tainted 4.5.0+ #88
Hardware name: linux,dummy-virt (DT)
task: ffffffc1f6665400 ti: ffffffc1d6418000 task.ti: ffffffc1d6418000
PC is at f71805f_find+0x6c/0x358 [f71805f]
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a58e ("hwmon: New f71805f driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 755a9b0f8aaa5639ba5671ca50080852babb89ce ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f0a7 ("hwmon: New PC87427 hardware monitoring driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c0826756744c0ac1df600a5e4cca1a341b13101 ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6410408ad2a798c4cc685252c1baa713be0ad69 ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 14b97ba5c20056102b3dd22696bf17b057e60976 ]
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6cd ("hwmon/vt1211: Add probing of alternate config index port")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07bd14ccc3049f9c0147a91a4227a571f981601a ]
Add the missing unlock before return from function set_fan_div()
in the error handling case.
Fixes: c9c63915519b ("hwmon: (lm80) fix a missing check of the status of SMBus read")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9aa3aa15f4c2f74f47afd6c5db4b420fadf3f315 ]
In lm80_probe(), if lm80_read_value() fails, it returns a negative
error number which is stored to data->fan[f_min] and will be further
used. We should avoid using the data if the read fails.
The fix checks if lm80_read_value() fails, and if so, returns with the
error number.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c9c63915519b1def7043b184680f33c24cd49d7b ]
If lm80_read_value() fails, it returns a negative number instead of the
correct read data. Therefore, we should avoid using the data if it
fails.
The fix checks if lm80_read_value() fails, and if so, returns with the
error number.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
[groeck: One variable for return values is enough]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 09aaf6813cfca4c18034fda7a43e68763f34abb1 ]
Both datasheet and comments of store_temp_mode() tell us that temp1~4_type
is writable, so fix it.
Signed-off-by: Yao Wang <wangyao@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Fixes: 39deb6993e7c (" hwmon: (w83795) Simplify temperature sensor type handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 38cd989ee38c16388cde89db5b734f9d55b905f9 ]
The current register (04h) has a sign bit at MSB. The comments
for this calculation also mention that it's a signed register.
However, the regval is unsigned type so result of calculation
turns out to be an incorrect value when current is negative.
This patch simply fixes this by adding a casting to s16.
Fixes: 5d389b125186c ("hwmon: (ina2xx) Make calibration register value fixed")
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3e61f01d755188cb6c2dcf5a244b9c0937c258e ]
If gcc decides not to inline make_sensor_label():
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95dcd64bc5a27080beaa344edfe5bdcca3d2e7dc ]
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7c6a55606b5c46b449d76588968b4d8caae903f upstream.
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the sub |
