| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
stuck state
[ Upstream commit e479187748a8f151a85116a7091c599b121fdea5 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 65299e8bfb24774e6340e93ae49f6626598917c8 ]
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ac05a8a927e5a1027592d8f98510a511dadeed14 upstream.
This adds the negation needed for proper finger detection on Ilitek
ili2107/ili210x. This fixes polling issues (on Amazon Kindle Fire)
caused by returning false for the cooresponding finger on the touchscreen.
Signed-off-by: Hansem Ro <hansemro@outlook.com>
Fixes: e3559442afd2a ("ili210x - rework the touchscreen sample processing")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30b3f68715595dee7fe4d9bd91a2252c3becdf0a upstream.
The touch coordinate register contains the following:
byte 3 byte 2 byte 1
+--------+--------+ +-----------------+ +-----------------+
| | | | | | |
| X[3:0] | Y[3:0] | | Y[11:4] | | X[11:4] |
| | | | | | |
+--------+--------+ +-----------------+ +-----------------+
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e59 ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fafd320ae51b9c72d371585b2501f86640ea7b7d upstream.
Add default write command package to prevent i2c quirk error of zero
data length as Raydium touch firmware update is executed.
Signed-off-by: jeffrey.lin <jeffrey.lin@rad-ic.com>
Link: https://lore.kernel.org/r/1608031217-7247-1-git-send-email-jeffrey.lin@raydium.corp-partner.google.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 836f308cb5c72d48e2dff8d3e64c3adb94f4710d ]
zinitix_init_touch() returns error code or 0 for success and therefore
return type must be int, not bool.
Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/YC8z2bXc3Oy8pABa@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0958351e93fa0ac142f6dd8bd844441594f30a57 ]
If elo_setup_10() fails then this should return an error code instead
of success.
Fixes: fae3006e4b42 ("Input: elo - add support for non-pressure-sensitive touchscreens")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFd5CvDu+jVmfW@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0b7d2815839024e5181bd2572f5d8d4f65363b3 ]
If v4l2_ctrl_handler_setup() fails then probe() should return an error
code instead of returning success.
Fixes: cee1e3e2ef39 ("media: add video control handlers using V4L2 control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFkbATXa5fA3xj@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 60159e9e7bc7e528c103b6b6d47dfd83af29669c upstream.
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2dce6db70c77bbe639f5cd9cc796fb8f2694a7d0 upstream.
The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.
This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.
This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 03e2c9c782f721b661a0e42b1b58f394b5298544 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44f3 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 820830ec918f6c3dcd77a54a1c6198ab57407916 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd9b6f653008d450f337602f3d52a646 ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e52cd628a03f72a547dbf90ccb703ee64800504a ]
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d4858f94a ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027105416.18773-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a fix for cm109 stomping on its own control URB if it tries to toggle
buzzer immediately after userspace opens input device (found by
syzcaller)
- another fix for Raydium touchscreens that do not like splitting
command transfers
- quirks for i8042, soc_button_array, and goodix drivers to make them
work better with certain hardware.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - add upside-down quirk for Teclast X98 Pro tablet
Input: cm109 - do not stomp on control URB
Input: i8042 - add Acer laptops to the i8042 reset list
Input: cros_ec_keyb - send 'scancodes' in addition to key events
Input: soc_button_array - add Lenovo Yoga Tablet2 1051L to the dmi_use_low_level_irq list
Input: raydium_ts_i2c - do not split tx transactions
|
|
The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhost
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Raydium device does not like splitting of tx transactions into multiple
messages - one for the register address and one for the actual data. This
results in incorrect behavior on the device side.
This change updates raydium_i2c_read and raydium_i2c_write to create
i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer
which decides based on the address whether the bank switch command should
be sent. The bank switch header is still added by raydium_i2c_read and
raydium_i2c_write to ensure that all these operations are performed as part
of a single I2C transfer. It guarantees that no other transactions are
initiated to any other device on the same bus after the bank switch command
is sent.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20201205005941.1427643-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for 'RETRIGEN' handling in Atmel touch controllers that was
causing lost interrupts on systems using edge-triggered interrupts, a
quirk for i8042 driver, and a couple more fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix lost interrupts
Input: xpad - support Ardwiino Controllers
Input: i8042 - add ByteSpeed touchpad to noloop table
Input: i8042 - fix error return code in i8042_setup_aux()
Input: soc_button_array - add missing include
|
|
After commit 74d905d2d38a devices requiring the workaround for edge
triggered interrupts stopped working.
The hardware needs the quirk to be used before even proceeding to
check if the quirk is needed because mxt_acquire_irq() is called
before mxt_check_retrigen() is called and at this point pending IRQs
need to be checked, and if the workaround is not active, all
interrupts will be lost from this point.
Solve this by switching the calls around.
Reported-by: Andre Müller <andre.muller@web.de>
Tested-by: Andre Müller <andre.muller@web.de>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 74d905d2d38a ("Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201201123026.1416743-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
|
|
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b0a ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for ADC driven joysticks
- a new Zintix touchscreen driver
- enhancements to Intel SoC button array driver
- support for F3A "function" in Synaptics RMI4 driver
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: Add MAINTAINERS entry for SiS i2c touch input driver
Input: evdev - per-client waitgroups
Input: synaptics - enable InterTouch for ThinkPad T14 Gen 1
Input: synaptics - enable InterTouch for ThinkPad P1/X1E gen 2
Input: synaptics-rmi4 - support bootloader v8 in f34v7
Input: synaptics-rmi4 - add support for F3A
Input: synaptics-rmi4 - rename f30_data to gpio_data
Input: add zinitix touchscreen driver
dt-bindings: input/touchscreen: add bindings for zinitix
Input: joystick - add ADC attached joystick driver.
dt-bindings: input: Add docs for ADC driven joystick
Input: sun4i-ps2 - fix handling of platform_get_irq() error
Input: twl4030_keypad - fix handling of platform_get_irq() error
Input: omap4-keypad - fix handling of platform_get_irq() error
Input: ep93xx_keypad - fix handling of platform_get_irq() error
Input: stmfts - fix a & vs && typo
Input: imx6ul_tsc - unify open/close and PM paths
Input: imx6ul_tsc - clean up some errors in imx6ul_tsc_resume()
Input: elants_i2c - fix typo for an attribute to show calibration count
Input: elants_i2c - report resolution of ABS_MT_TOUCH_MAJOR by FW information.
...
|
|
Add support for the bt541 touchscreen IC from zinitix, loosely based on
downstream driver. The driver currently supports multitouch (5 touch points).
The bt541 seems to support touch keys, but the support was not added because
that functionality is not being utilized by the touchscreen used for testing.
Based on the similartities between downstream drivers, it seems likely that
other similar touchscreen ICs can be supported with this driver in the future.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Link: https://lore.kernel.org/r/20201001122949.16846-1-michael.srba@seznam.cz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In stmfts_sysfs_hover_enable_write(), we should check value and
sdata->hover_enabled is all true.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200916141941.16684-1-yuehaibing@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Open/close and resume/suspend paths are very similar, let's factor out
common parts.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If imx6ul_tsc_init() fails then we need to clean up the clocks.
I reversed the "if (input_dev->users) {" condition to make the code a
bit simpler.
Fixes: 6cc527b05847 ("Input: imx6ul_tsc - propagate the errors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124942.GC183976@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fixed typo for command from 0xE0 to 0xD0.
Fixes: cf520c643012 ("Input: elants_i2c - provide an attribute to show calibration count")
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1600238783-32303-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch adds a new behavior to report touch major resolution
based on information provided by firmware.
In initial process, driver acquires touch information from touch ic.
It contains one byte about the resolution value of ABS_MT_TOUCH_MAJOR.
Touch driver will report touch major resolution by this information.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/1598581195-9874-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
RM_CMD_BANK_SWITCH
On an AMD chromebook, where the same I2C bus is shared by both Raydium
touchscreen and a trackpad device, it is observed that interleaving of
I2C messages when `raydium_i2c_read_message()` is called leads to the
Raydium touch IC reporting incorrect information. This is the sequence
that was observed to result in the above issue:
* I2C write to Raydium device for RM_CMD_BANK_SWITCH
* I2C write to trackpad device
* I2C read from trackpad device
* I2C write to Raydium device for setting address
* I2C read from Raydium device >>>> This provides incorrect
information
This change adds a new helper function `raydium_i2c_xfer()` that
performs I2C transactions to the Raydium device. It uses the register
address to decide if RM_CMD_BANK_SWITCH header needs to be sent to the
device (i.e. if register address is greater than 255, then bank switch
header is sent before the rest of the transaction). Additionally, it
ensures that all the I2C operations performed as part of
`raydium_i2c_xfer()` are done as a single i2c_transfer. This
guarantees that no other transactions are initiated to any other
device on the same bus in between. Additionally,
`raydium_i2c_{send|read}*` functions are refactored to use this new
helper function.
Verified with the patch across multiple reboots (>100) that the
information reported by the Raydium touchscreen device during probe
is correct.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20200821024006.3399663-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad controller driver supporting newer ICs
with enhanced precision reports and a new firmware update process
- an update to EXC3000 touch controller supporting additional parts
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: exc3000 - add support to query model and fw_version
Input: exc3000 - add reset gpio support
Input: exc3000 - add EXC80H60 and EXC80H84 support
dt-bindings: touchscreen: Convert EETI EXC3000 touchscreen to json-schema
Input: sentelic - fix error return when fsp_reg_write fails
Input: alps - remove redundant assignment to variable ret
Input: ims-pcu - return error code rather than -ENOMEM
Input: elan_i2c - add ic type 0x15
Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary
Input: uinput - fix typo in function name documentation
Input: ati_remote2 - add missing newlines when printing module parameters
Input: psmouse - add a newline when printing 'proto' by sysfs
Input: synaptics-rmi4 - drop a duplicated word
Input: elan_i2c - add support for high resolution reports
Input: elan_i2c - do not constantly re-query pattern ID
Input: elan_i2c - add firmware update info for ICs 0x11, 0x13, 0x14
Input: elan_i2c - handle firmware updated on newer ICs
Input: elan_i2c - add support for different firmware page sizes
Input: elan_i2c - fix detecting IAP version on older controllers
Input: elan_i2c - handle devices with patterns above 1
...
|
|
Expose model and fw_version via sysfs. Also query the model
in probe to make sure, that the I2C communication with the
device works before successfully probing the driver.
This is a bit complicated, since EETI devices do not have
a sync interface. Sending the commands and directly reading
does not work. Sending the command and waiting for some time
is also not an option, since there might be touch events in
the mean time.
Last but not least we do not cache the results, since this
interface can be used to check the I2C communication is still
working as expected.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20200805160520.456570-5-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add basic support for an optional reset gpio.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-4-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for EXC80H60 and EXCH84 controllers, which
use a different event type id and have two extra bits for the
resolution (so the maximum is 16K instead of 4K).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-3-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems"
* tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (428 commits)
staging: most: fix up movement of USB driver
staging: rts5208: clear alignment style issues
staging: r8188eu: replace rtw_netdev_priv define with inline function
staging: netlogic: clear alignment style issues
staging: android: ashmem: Fix lockdep warning for write operation
drivers: most: add USB adapter driver
staging: most: Use %pM format specifier for MAC addresses
staging: ks7010: Use %pM format specifier for MAC addresses
staging: qlge: qlge_dbg: removed comment repition
staging: wfx: Use flex_array_size() helper in memcpy()
staging: rtl8723bs: Align macro definitions
staging: rtl8723bs: Clean up function declations
staging: rtl8723bs: Fix coding style errors
drivers: staging: audio: Fix the missing header file for helper file
staging: greybus: audio: Enable GB codec, audio module compilation.
staging: greybus: audio: Add helper APIs for dynamic audio modules
staging: greybus: audio: Resolve compilation error in topology parser
staging: greybus: audio: Resolve compilation errors for GB codec module
staging: greybus: audio: Maintain jack list within GB Audio module
staging: greybus: audio: Update snd_jack FW usage as per new APIs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull uninitialized_var() macro removal from Kees Cook:
"This is long overdue, and has hidden too many bugs over the years. The
series has several "by hand" fixes, and then a trivial treewide
replacement.
- Clean up non-trivial uses of uninitialized_var()
- Update documentation and checkpatch for uninitialized_var() removal
- Treewide removal of uninitialized_var()"
* tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
compiler: Remove uninitialized_var() macro
treewide: Remove uninitialized_var() usage
checkpatch: Remove awareness of uninitialized_var() macro
mm/debug_vm_pgtable: Remove uninitialized_var() usage
f2fs: Eliminate usage of uninitialized_var() macro
media: sur40: Remove uninitialized_var() usage
KVM: PPC: Book3S PR: Remove uninitialized_var() usage
clk: spear: Remove uninitialized_var() usage
clk: st: Remove uninitialized_var() usage
spi: davinci: Remove uninitialized_var() usage
ide: Remove uninitialized_var() usage
rtlwifi: rtl8192cu: Remove uninitialized_var() usage
b43: Remove uninitialized_var() usage
drbd: Remove uninitialized_var() usage
x86/mm/numa: Remove uninitialized_var() usage
docs: deprecated.rst: Add uninitialized_var()
|
|
The workaround of reading all messages until an invalid is received is a
way of forcing the CHG line high, which means that when using
edge-triggered interrupts the interrupt can be acquired.
With level-triggered interrupts the workaround is unnecessary.
Also, most recent maXTouch chips have a feature called RETRIGEN which, when
enabled, reasserts the interrupt line every cycle if there are messages
waiting. This also makes the workaround unnecessary.
Note: the RETRIGEN feature is only in some firmware versions/chips, it's
not valid simply to enable the bit.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
(cherry picked from ndyer/linux/for-upstream commit 1ae4e8281e491b22442cd5acdfca1862555f8ecb)
[gdavis: Fix conflicts due to v4.6-rc7 commit eb43335c4095 ("Input:
atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_reset").]
Signed-off-by: George G. Davis <george_davis@mentor.com>
[jiada: reset use_retrigen_workaround at beginning of mxt_check_retrigen()
call mxt_check_retrigen() after mxt_acquire_irq() in mxt_initialize()
replace white-spaces with tab for MXT_COMMS_RETRIGEN
Changed to check if IRQ is level type]
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200727151637.23810-1-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync up with 'for-linus' branch to resolve conflict in Elan touchpad
driver.
|
|
Bring in update to Elan touchpad driver to support newer touchpads with
higher resolution.
|
|
We need the staging fixes in here, and it resolves a merge issue with an
iio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings (e.g.
"unused variable"). If the compiler thinks it is uninitialized, either
simply initialize the variable or make compiler changes. As a precursor
to removing[2] this[3] macro[4], just remove this variable since it was
actually unused:
drivers/input/touchscreen/sur40.c:459:6: warning: variable 'packet_id' set but not used [-Wunused-but-set-variable]
459 | u32 packet_id;
| ^~~~~~~~~
However, in keeping with the documentation desires outlined in commit
335abaea7a27 ("Input: sur40 - silence unnecessary noisy debug output"),
comment out the assignment instead of removing it.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Fixes: 335abaea7a27 ("Input: sur40 - silence unnecessary noisy debug output")
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200707180857.GA30600@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Switch to the "new" I2C probe API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200520153936.46869-3-sebastian.reichel@collab |
