| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 3569dd07aaad71920c5ea4da2d5cc9a167c1ffd4 upstream.
The Intel IOMMU driver opportunistically skips a few top level page
tables from the domain paging directory while programming the IOMMU
context entry. However there is an implicit assumption in the code that
domain's adjusted guest address width (agaw) would always be greater
than IOMMU's agaw.
The IOMMU capabilities in an upcoming platform cause the domain's agaw
to be lower than IOMMU's agaw. The issue is seen when the IOMMU supports
both 4-level and 5-level paging. The domain builds a 4-level page table
based on agaw of 2. However the IOMMU's agaw is set as 3 (5-level). In
this case the code incorrectly tries to skip page page table levels.
This causes the IOMMU driver to avoid programming the context entry. The
fix handles this case and programs the context entry accordingly.
Fixes: de24e55395698 ("iommu/vt-d: Simplify domain_context_mapping_one")
Cc: <stable@vger.kernel.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reported-by: Ramos Falcon, Ernesto R <ernesto.r.ramos.falcon@intel.com>
Tested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 829383e183728dec7ed9150b949cd6de64127809 ]
memunmap() should be used to free the return of memremap(), not
iounmap().
Fixes: dfddb969edf0 ('iommu/vt-d: Switch from ioremap_cache to memremap')
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5b78f2e349eef5d4fca5dc1cf5a3b4b2cc27abd ]
If iommu_ops.add_device() fails, iommu_ops.domain_free() is still
called, leading to a crash, as the domain was only partially
initialized:
ipmmu-vmsa e67b0000.mmu: Cannot accommodate DMA translation for IOMMU page tables
sata_rcar ee300000.sata: Unable to initialize IPMMU context
iommu: Failed to add device ee300000.sata to group 0: -22
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038
...
Call trace:
ipmmu_domain_free+0x1c/0xa0
iommu_group_release+0x48/0x68
kobject_put+0x74/0xe8
kobject_del.part.0+0x3c/0x50
kobject_put+0x60/0xe8
iommu_group_get_for_dev+0xa8/0x1f0
ipmmu_add_device+0x1c/0x40
of_iommu_configure+0x118/0x190
Fix this by checking if the domain's context already exists, before
trying to destroy it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Fixes: d25a2a16f0889 ('iommu: Add driver for Renesas VMSA-compatible IPMMU')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 19ed3e2dd8549c1a34914e8dad01b64e7837645a ]
When handling page request without pasid event, go to "no_pasid"
branch instead of "bad_req". Otherwise, a NULL pointer deference
will happen there.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: a222a7f0bb6c9 'iommu/vt-d: Implement page request handling'
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ebb1bc2d63d90dd204169e21fd7a0b4bb8c776e ]
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Fixes: 2bf9a0a12749 ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3c120143f584360a13614787e23ae2cdcb5e5ccd ]
Although the mapping has already been removed in the page table, it maybe
still exist in TLB. Suppose the freed IOVAs is reused by others before the
flush operation completed, the new user can not correctly access to its
meomory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Fixes: b1516a14657a ('iommu/amd: Implement flush queue')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d535967ac658966c6ade8f82b5799092f7d5441 ]
When PRI queue occurs overflow, driver should update the OVACKFLG to
the PRIQ consumer register, otherwise subsequent PRI requests will not
be processed.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Miao Zhong <zhongmiao@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 46583e8c48c5a094ba28060615b3a7c8c576690f ]
When attaching a device to an IOMMU group with
CONFIG_DEBUG_ATOMIC_SLEEP=y:
BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 128, pid: 61, name: kworker/1:1
...
Call trace:
...
arm_lpae_alloc_pgtable+0x114/0x184
arm_64_lpae_alloc_pgtable_s1+0x2c/0x128
arm_32_lpae_alloc_pgtable_s1+0x40/0x6c
alloc_io_pgtable_ops+0x60/0x88
ipmmu_attach_device+0x140/0x334
ipmmu_attach_device() takes a spinlock, while arm_lpae_alloc_pgtable()
allocates memory using GFP_KERNEL. Originally, the ipmmu-vmsa driver
had its own custom page table allocation implementation using
GFP_ATOMIC, hence the spinlock was fine.
Fix this by replacing the spinlock by a mutex, like the arm-smmu driver
does.
Fixes: f20ed39f53145e45 ("iommu/ipmmu-vmsa: Use the ARM LPAE page table allocator")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c48db44924298ad0cb5a6386b88017539be8822 upstream.
PFSID should be used in the invalidation descriptor for flushing
device IOTLBs on SRIOV VFs.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: stable@vger.kernel.org
Cc: "Ashok Raj" <ashok.raj@intel.com>
Cc: "Lu Baolu" <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f725561e168485eff7277d683405c05b192f537 upstream.
When SRIOV VF device IOTLB is invalidated, we need to provide
the PF source ID such that IOMMU hardware can gauge the depth
of invalidation queue which is shared among VFs. This is needed
when device invalidation throttle (DIT) capability is supported.
This patch adds bit definitions for checking and tracking PFSID.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: stable@vger.kernel.org
Cc: "Ashok Raj" <ashok.raj@intel.com>
Cc: "Lu Baolu" <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9d2e6505f6d6934e681aed502f566198cb25c74a ]
after commit a1ddcbe93010 ("iommu/vt-d: Pass dmar_domain directly into
iommu_flush_iotlb_psi", 2015-08-12), we have domain pointer as parameter
to iommu_flush_iotlb_psi(), so no need to fetch it from cache again.
More importantly, a NULL reference pointer bug is reported on RHEL7 (and
it can be reproduced on some old upstream kernels too, e.g., v4.13) by
unplugging an 40g nic from a VM (hard to test unplug on real host, but
it should be the same):
https://bugzilla.redhat.com/show_bug.cgi?id=1531367
[ 24.391863] pciehp 0000:00:03.0:pcie004: Slot(0): Attention button pressed
[ 24.393442] pciehp 0000:00:03.0:pcie004: Slot(0): Powering off due to button press
[ 29.721068] i40evf 0000:01:00.0: Unable to send opcode 2 to PF, err I40E_ERR_QUEUE_EMPTY, aq_err OK
[ 29.783557] iommu: Removing device 0000:01:00.0 from group 3
[ 29.784662] BUG: unable to handle kernel NULL pointer dereference at 0000000000000304
[ 29.785817] IP: iommu_flush_iotlb_psi+0xcf/0x120
[ 29.786486] PGD 0
[ 29.786487] P4D 0
[ 29.786812]
[ 29.787390] Oops: 0000 [#1] SMP
[ 29.787876] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_ng
[ 29.795371] CPU: 0 PID: 156 Comm: kworker/0:2 Not tainted 4.13.0 #14
[ 29.796366] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.11.0-1.el7 04/01/2014
[ 29.797593] Workqueue: pciehp-0 pciehp_power_thread
[ 29.798328] task: ffff94f5745b4a00 task.stack: ffffb326805ac000
[ 29.799178] RIP: 0010:iommu_flush_iotlb_psi+0xcf/0x120
[ 29.799919] RSP: 0018:ffffb326805afbd0 EFLAGS: 00010086
[ 29.800666] RAX: ffff94f5bc56e800 RBX: 0000000000000000 RCX: 0000000200000025
[ 29.801667] RDX: ffff94f5bc56e000 RSI: 0000000000000082 RDI: 0000000000000000
[ 29.802755] RBP: ffffb326805afbf8 R08: 0000000000000000 R09: ffff94f5bc86bbf0
[ 29.803772] R10: ffffb326805afba8 R11: 00000000000ffdc4 R12: ffff94f5bc86a400
[ 29.804789] R13: 0000000000000000 R14: 00000000ffdc4000 R15: 0000000000000000
[ 29.805792] FS: 0000000000000000(0000) GS:ffff94f5bfc00000(0000) knlGS:0000000000000000
[ 29.806923] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 29.807736] CR2: 0000000000000304 CR3: 000000003499d000 CR4: 00000000000006f0
[ 29.808747] Call Trace:
[ 29.809156] flush_unmaps_timeout+0x126/0x1c0
[ 29.809800] domain_exit+0xd6/0x100
[ 29.810322] device_notifier+0x6b/0x70
[ 29.810902] notifier_call_chain+0x4a/0x70
[ 29.812822] __blocking_notifier_call_chain+0x47/0x60
[ 29.814499] blocking_notifier_call_chain+0x16/0x20
[ 29.816137] device_del+0x233/0x320
[ 29.817588] pci_remove_bus_device+0x6f/0x110
[ 29.819133] pci_stop_and_remove_bus_device+0x1a/0x20
[ 29.820817] pciehp_unconfigure_device+0x7a/0x1d0
[ 29.822434] pciehp_disable_slot+0x52/0xe0
[ 29.823931] pciehp_power_thread+0x8a/0xa0
[ 29.825411] process_one_work+0x18c/0x3a0
[ 29.826875] worker_thread+0x4e/0x3b0
[ 29.828263] kthread+0x109/0x140
[ 29.829564] ? process_one_work+0x3a0/0x3a0
[ 29.831081] ? kthread_park+0x60/0x60
[ 29.832464] ret_from_fork+0x25/0x30
[ 29.833794] Code: 85 ed 74 0b 5b 41 5c 41 5d 41 5e 41 5f 5d c3 49 8b 54 24 60 44 89 f8 0f b6 c4 48 8b 04 c2 48 85 c0 74 49 45 0f b6 ff 4a 8b 3c f8 <80> bf
[ 29.838514] RIP: iommu_flush_iotlb_psi+0xcf/0x120 RSP: ffffb326805afbd0
[ 29.840362] CR2: 0000000000000304
[ 29.841716] ---[ end trace b10ec0d6900868d3 ]---
This patch fixes that problem if applied to v4.13 kernel.
The bug does not exist on latest upstream kernel since it's fixed as a
side effect of commit 13cf01744608 ("iommu/vt-d: Make use of iova
deferred flushing", 2017-08-15). But IMHO it's still good to have this
patch upstream.
CC: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Fixes: a1ddcbe93010 ("iommu/vt-d: Pass dmar_domain directly into iommu_flush_iotlb_psi")
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbe4b3af9d9e3172fb9aa1f8dcdfaedcb381fc64 upstream.
A memory block was allocated in intel_svm_bind_mm() but never freed
in a failure path. This patch fixes this by free it to avoid memory
leakage.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Fixes: 2f26e0a9c9860 ('iommu/vt-d: Add basic SVM PASID support')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 72d548113881dd32bf7f0b221d031e6586468437 ]
It is unlikely request_threaded_irq will fail, but if it does for some
reason we should clear iommu->pr_irq in the error path. Also
intel_svm_finish_prq shouldn't try to clean up the page request
interrupt if pr_irq is 0. Without these, if request_threaded_irq were
to fail the following occurs:
fail with no fixes:
[ 0.683147] ------------[ cut here ]------------
[ 0.683148] NULL pointer, cannot free irq
[ 0.683158] WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:1632 irq_domain_free_irqs+0x126/0x140
[ 0.683160] Modules linked in:
[ 0.683163] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc2 #3
[ 0.683165] Hardware name: /NUC7i3BNB, BIOS BNKBL357.86A.0036.2017.0105.1112 01/05/2017
[ 0.683168] RIP: 0010:irq_domain_free_irqs+0x126/0x140
[ 0.683169] RSP: 0000:ffffc90000037ce8 EFLAGS: 00010292
[ 0.683171] RAX: 000000000000001d RBX: ffff880276283c00 RCX: ffffffff81c5e5e8
[ 0.683172] RDX: 0000000000000001 RSI: 0000000000000096 RDI: 0000000000000246
[ 0.683174] RBP: ffff880276283c00 R08: 0000000000000000 R09: 000000000000023c
[ 0.683175] R10: 0000000000000007 R11: 0000000000000000 R12: 000000000000007a
[ 0.683176] R13: 0000000000000001 R14: 0000000000000000 R15: 0000010010000000
[ 0.683178] FS: 0000000000000000(0000) GS:ffff88027ec80000(0000) knlGS:0000000000000000
[ 0.683180] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 0.683181] CR2: 0000000000000000 CR3: 0000000001c09001 CR4: 00000000003606e0
[ 0.683182] Call Trace:
[ 0.683189] intel_svm_finish_prq+0x3c/0x60
[ 0.683191] free_dmar_iommu+0x1ac/0x1b0
[ 0.683195] init_dmars+0xaaa/0xaea
[ 0.683200] ? klist_next+0x19/0xc0
[ 0.683203] ? pci_do_find_bus+0x50/0x50
[ 0.683205] ? pci_get_dev_by_id+0x52/0x70
[ 0.683208] intel_iommu_init+0x498/0x5c7
[ 0.683211] pci_iommu_init+0x13/0x3c
[ 0.683214] ? e820__memblock_setup+0x61/0x61
[ 0.683217] do_one_initcall+0x4d/0x1a0
[ 0.683220] kernel_init_freeable+0x186/0x20e
[ 0.683222] ? set_debug_rodata+0x11/0x11
[ 0.683225] ? rest_init+0xb0/0xb0
[ 0.683226] kernel_init+0xa/0xff
[ 0.683229] ret_from_fork+0x1f/0x30
[ 0.683259] Code: 89 ee 44 89 e7 e8 3b e8 ff ff 5b 5d 44 89 e7 44 89 ee 41 5c 41 5d 41 5e e9 a8 84 ff ff 48 c7 c7 a8 71 a7 81 31 c0 e8 6a d3 f9 ff <0f> ff 5b 5d 41 5c 41 5d 41 5
e c3 0f 1f 44 00 00 66 2e 0f 1f 84
[ 0.683285] ---[ end trace f7650e42792627ca ]---
with iommu->pr_irq = 0, but no check in intel_svm_finish_prq:
[ 0.669561] ------------[ cut here ]------------
[ 0.669563] Trying to free already-free IRQ 0
[ 0.669573] WARNING: CPU: 3 PID: 1 at kernel/irq/manage.c:1546 __free_irq+0xa4/0x2c0
[ 0.669574] Modules linked in:
[ 0.669577] CPU: 3 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc2 #4
[ 0.669579] Hardware name: /NUC7i3BNB, BIOS BNKBL357.86A.0036.2017.0105.1112 01/05/2017
[ 0.669581] RIP: 0010:__free_irq+0xa4/0x2c0
[ 0.669582] RSP: 0000:ffffc90000037cc0 EFLAGS: 00010082
[ 0.669584] RAX: 0000000000000021 RBX: 0000000000000000 RCX: ffffffff81c5e5e8
[ 0.669585] RDX: 0000000000000001 RSI: 0000000000000086 RDI: 0000000000000046
[ 0.669587] RBP: 0000000000000000 R08: 0000000000000000 R09: 000000000000023c
[ 0.669588] R10: 0000000000000007 R11: 0000000000000000 R12: ffff880276253960
[ 0.669589] R13: ffff8802762538a4 R14: ffff880276253800 R15: ffff880276283600
[ 0.669593] FS: 0000000000000000(0000) GS:ffff88027ed80000(0000) knlGS:0000000000000000
[ 0.669594] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 0.669596] CR2: 0000000000000000 CR3: 0000000001c09001 CR4: 00000000003606e0
[ 0.669602] Call Trace:
[ 0.669616] free_irq+0x30/0x60
[ 0.669620] intel_svm_finish_prq+0x34/0x60
[ 0.669623] free_dmar_iommu+0x1ac/0x1b0
[ 0.669627] init_dmars+0xaaa/0xaea
[ 0.669631] ? klist_next+0x19/0xc0
[ 0.669634] ? pci_do_find_bus+0x50/0x50
[ 0.669637] ? pci_get_dev_by_id+0x52/0x70
[ 0.669639] intel_iommu_init+0x498/0x5c7
[ 0.669642] pci_iommu_init+0x13/0x3c
[ 0.669645] ? e820__memblock_setup+0x61/0x61
[ 0.669648] do_one_initcall+0x4d/0x1a0
[ 0.669651] kernel_init_freeable+0x186/0x20e
[ 0.669653] ? set_debug_rodata+0x11/0x11
[ 0.669656] ? rest_init+0xb0/0xb0
[ 0.669658] kernel_init+0xa/0xff
[ 0.669661] ret_from_fork+0x1f/0x30
[ 0.669662] Code: 7a 08 75 0e e9 c3 01 00 00 4c 39 7b 08 74 57 48 89 da 48 8b 5a 18 48 85 db 75 ee 89 ee 48 c7 c7 78 67 a7 81 31 c0 e8 4c 37 fa ff <0f> ff 48 8b 34 24 4c 89 ef e
8 0e 4c 68 00 49 8b 46 40 48 8b 80
[ 0.669688] ---[ end trace 58a470248700f2fc ]---
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit abaa7e5b054aae567861628b74dbc7fbf8ed79e8 ]
Move the registration of the OMAP IOMMU platform driver before
setting the IOMMU callbacks on the platform bus. This causes
the IOMMU devices to be probed first before the .add_device()
callback is invoked for all registered devices, and allows
the iommu_group support to be added to the OMAP IOMMU driver.
While at this, also check for the return status from bus_set_iommu.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5016bdb796b3726eec043ca0ce3be981f712c756 ]
Normally, calling alloc_iova() using an iova_domain with insufficient
pfns remaining between start_pfn and dma_limit will fail and return a
NULL pointer. Unexpectedly, if such a "full" iova_domain contains an
iova with pfn_lo == 0, the alloc_iova() call will instead succeed and
return an iova containing invalid pfns.
This is caused by an underflow bug in __alloc_and_insert_iova_range()
that occurs after walking the "full" iova tree when the search ends
at the iova with pfn_lo == 0 and limit_pfn is then adjusted to be just
below that (-1). This (now huge) limit_pfn gives the impression that a
vast amount of space is available between it and start_pfn and thus
a new iova is allocated with the invalid pfn_hi value, 0xFFF.... .
To rememdy this, a check is introduced to ensure that adjustments to
limit_pfn will not underflow.
This issue has been observed in the wild, and is easily reproduced with
the following sample code.
struct iova_domain *iovad = kzalloc(sizeof(*iovad), GFP_KERNEL);
struct iova *rsvd_iova, *good_iova, *bad_iova;
unsigned long limit_pfn = 3;
unsigned long start_pfn = 1;
unsigned long va_size = 2;
init_iova_domain(iovad, SZ_4K, start_pfn, limit_pfn);
rsvd_iova = reserve_iova(iovad, 0, 0);
good_iova = alloc_iova(iovad, va_size, limit_pfn, true);
bad_iova = alloc_iova(iovad, va_size, limit_pfn, true);
Prior to the patch, this yielded:
*rsvd_iova == {0, 0} /* Expected */
*good_iova == {2, 3} /* Expected */
*bad_iova == {-2, -1} /* Oh no... */
After the patch, bad_iova is NULL as expected since inadequate
space remains between limit_pfn and start_pfn after allocating
good_iova.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 563b5cbe334e9503ab2b234e279d500fc4f76018 upstream.
For PCI devices behind an aliasing PCIe-to-PCI/X bridge, the bridge
alias to DevFn 0.0 on the subordinate bus may match the original RID of
the device, resulting in the same SID being present in the device's
fwspec twice. This causes trouble later in arm_smmu_write_strtab_ent()
when we wind up visiting the STE a second time and find it already live.
Avoid the issue by giving arm_smmu_install_ste_for_dev() the cleverness
to skip over duplicates. It seems mildly counterintuitive compared to
preventing the duplicates from existing in the first place, but since
the DT and ACPI probe paths build their fwspecs differently, this is
actually the cleanest and most self-contained way to deal with it.
Fixes: 8f78515425da ("iommu/arm-smmu: Implement of_xlate() for SMMUv3")
Reported-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <Tomasz.Nowicki@cavium.com>
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57d72e159b60456c8bb281736c02ddd3164037aa upstream.
Kasan reports a double free when finalise_stage_fn fails: the io_pgtable
ops are freed by arm_smmu_domain_finalise and then again by
arm_smmu_domain_free. Prevent this by leaving pgtbl_ops empty on failure.
Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cd37a296a9f890586665bb8974a8b17ee2f17d6d ]
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9ada ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b92b4fb5c14257c0e7eae291ecc1f7b1962e1699 ]
The extent of pages specified when applying a reserved region should
include up to the last page of the range, but not the page following
the range.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes: 8d54d6c8b8f3 ('iommu/amd: Implement apply_dm_region call-back')
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 395df08d2e1de238a9c8c33fdcd0e2160efd63a9 ]
There exist two Mediatek iommu drivers for the two different
generations of the device. But both drivers have the same name
"mtk-iommu". This breaks the registration of the second driver:
Error: Driver 'mtk-iommu' is already registered, aborting...
Fix this by changing the name for first generation to
"mtk-iommu-v1".
Fixes: b17336c55d89 ("iommu/mediatek: add support for mtk iommu generation one HW")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a03849e7210277fa212779b7cd9c30e1ab6194b2 ]
Do a check for already installed leaf entry at the current level before
dereferencing it in order to avoid walking the page table down with
wrong pointer to the next level.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
CC: Will Deacon <will.deacon@arm.com>
CC: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29a90b70893817e2f2bb3cea40a29f5308e21b21 upstream.
The intel-iommu DMA ops fail to correctly handle scatterlists where
sg->offset is greater than PAGE_SIZE - the IOVA allocation is computed
appropriately based on the page-aligned portion of the offset, but the
mapping is set up relative to sg->page, which means it fails to actually
cover the whole buffer (and in the worst case doesn't cover it at all):
(sg->dma_address + sg->dma_len) ----+
sg->dma_address ---------+ |
iov_pfn------+ | |
| | |
v v v
iova: a b c d e f
|--------|--------|--------|--------|--------|
<...calculated....>
[_____mapped______]
pfn: 0 1 2 3 4 5
|--------|--------|--------|--------|--------|
^ ^ ^
| | |
sg->page ----+ | |
sg->offset --------------+ |
(sg->offset + sg->length) ----------+
As a result, the caller ends up overrunning the mapping into whatever
lies beyond, which usually goes badly:
[ 429.645492] DMAR: DRHD: handling fault status reg 2
[ 429.650847] DMAR: [DMA Write] Request device [02:00.4] fault addr f2682000 ...
Whilst this is a fairly rare occurrence, it can happen from the result
of intermediate scatterlist processing such as scatterwalk_ffwd() in the
crypto layer. Whilst that particular site could be fixed up, it still
seems worthwhile to bring intel-iommu in line with other DMA API
implementations in handling this robustly.
To that end, fix the intel_map_sg() path to line up the mapping
correctly (in units of MM pages rather than VT-d pages to match the
aligned_nrpages() calculation) regardless of the offset, and use
sg_phys() consistently for clarity.
Reported-by: Harsh Jain <Harsh@chelsio.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed by: Ashok Raj <ashok.raj@intel.com>
Tested by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 810871c57011eb3e89e6768932757f169d666cd2 ]
To prevent corruption of the stage-1 context pointer field when
updating STEs, rebuild the entire containing dword instead of
clearing individual fields.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce76353f169a6471542d999baf3d29b121dce9c0 upstream.
The function only sends the flush command to the IOMMU(s),
but does not wait for its completion when it returns. Fix
that.
Fixes: 601367d76bd1 ('x86/amd-iommu: Remove iommu_flush_domain function')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ed46e66cc1b3d684042f92dfa2ab15ee917b4cac ]
Do a check for already installed leaf entry at the current level before
dereferencing it in order to avoid walking the page table down with
wrong pointer to the next level.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
CC: Will Deacon <will.deacon@arm.com>
CC: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d2aa6b814476a2e2794960f844344519246df72 ]
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b345d ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e19898077cfb642fe151ba22981e795c74d9e114 ]
Currently the driver sets all the device transactions privileges
to UNPRIVILEGED, but there are cases where the iommu masters wants
to isolate privileged supervisor and unprivileged user.
So don't override the privileged setting to unprivileged, instead
set it to default as incoming and let it be controlled by the pagetable
settings.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efe6f241602cb61466895f6816b8ea6b90f04d4e upstream.
IRTE[GALogIntr] bit should set when enabling guest_mode, which enables
IOMMU to generate entry in GALog when IRTE[IsRun] is not set, and send
an interrupt to notify IOMMU driver.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Fixes: d98de49a53e48 ('iommu/amd: Enable vAPIC interrupt remapping mode by default')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84a21dbdef0b96d773599c33c2afbb002198d303 upstream.
Pass-through devices to VM guest can get updated IRQ affinity
information via irq_set_affinity() when not running in guest mode.
Currently, AMD IOMMU driver in GA mode ignores the updated information
if the pass-through device is setup to use vAPIC regardless of guest_mode.
This could cause invalid interrupt remapping.
Also, the guest_mode bit should be set and cleared only when
SVM updates posted-interrupt interrupt remapping information.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Fixes: d98de49a53e48 ('iommu/amd: Enable vAPIC interrupt remapping mode by default')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73dbd4a4230216b6a5540a362edceae0c9b4876b upstream.
In function amd_iommu_bind_pasid(), the control flow jumps
to label out_free when pasid_state->mm and mm is NULL. And
mmput(mm) is called. In function mmput(mm), mm is
referenced without validation. This will result in a NULL
dereference bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: f0aac63b873b ('iommu/amd: Don't hold a reference to mm_struct')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 938f1bbe35e3a7cb07e1fa7c512e2ef8bb866bdf upstream.
Even if a host controller's CPU-side MMIO windows into PCI I/O space do
happen to leak into PCI memory space such that it might treat them as
peer addresses, trying to reserve the corresponding I/O space addresses
doesn't do anything to help solve that problem. Stop doing a silly thing.
Fixes: fade1ec055dc ("iommu/dma: Avoid PCI host bridge windows")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 797a8b4d768c58caac58ee3e8cb36a164d1b7751 upstream.
We wouldn't normally expect ops->attach_dev() to fail, but on IOMMUs
with limited hardware resources, or generally misconfigured systems,
it is certainly possible. We report failure correctly from the external
iommu_attach_device() interface, but do not do so in iommu_group_add()
when attaching to the default domain. The result of failure there is
that the device, group and domain all get left in a broken,
part-configured state which leads to weird errors and misbehaviour down
the line when IOMMU API calls sort-of-but-don't-quite work.
Check the return value of __iommu_attach_device() on the default domain,
and refactor the error handling paths to cope with its failure and clean
up correctly in such cases.
Fixes: e39cb8a3aa98 ("iommu: Make sure a device is always attached to a domain")
Reported-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7116e115acdd74bc75a4daf6492b11d43505125 upstream.
dma_pte_free_level() recurses down the IOMMU page tables and frees
directory pages that are entirely contained in the given PFN range.
Unfortunately, it incorrectly calculates the starting address covered
by the PTE under consideration, which can lead to it clearing an entry
that is still in use.
This occurs if we have a scatterlist with an entry that has a length
greater than 1026 MB and is aligned to 2 MB for both the IOMMU and
physical addresses. For example, if __domain_mapping() is asked to map a
two-entry scatterlist with 2 MB and 1028 MB segments to PFN 0xffff80000,
it will ask if dma_pte_free_pagetable() is asked to PFNs from
0xffff80200 to 0xffffc05ff, it will also incorrectly clear the PFNs from
0xffff80000 to 0xffff801ff because of this issue. The current code will
set level_pfn to 0xffff80200, and 0xffff80200-0xffffc01ff fits inside
the range being cleared. Properly setting the level_pfn for the current
level under consideration catches that this PTE is outside of the range
being cleared.
This patch also changes the value passed into dma_pte_free_level() when
it recurses. This only affects the first PTE of the range being cleared,
and is handled by the existing code that ensures we start our cursor no
lower than start_pfn.
This was found when using dma_map_sg() to map large chunks of contiguous
memory, which immediatedly led to faults on the first access of the
erroneously-deleted mappings.
Fixes: 3269ee0bd668 ("intel-iommu: Fix leaks in pagetable freeing")
Reviewed-by: Benjamin Serebrin <serebrin@google.com>
Signed-off-by: David Dillow <dillow@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f73a7eee900e95404b61408a23a1df5c5811704c upstream.
Ever since commit 091d42e43d ("iommu/vt-d: Copy translation tables from
old kernel") the kdump kernel copies the IOMMU context tables from the
previous kernel. Each device mappings will be destroyed once the driver
for the respective device takes over.
This unfortunately breaks the workflow of mapping and unmapping a new
context to the IOMMU. The mapping function assumes that either:
1) Unmapping did the proper IOMMU flushing and it only ever flush if the
IOMMU unit supports caching invalid entries.
2) The system just booted and the initialization code took care of
flushing all IOMMU caches.
This assumption is not true for the kdump kernel since the context
tables have been copied from the previous kernel and translations could
have been cached ever since. So make sure to flush the IOTLB as well
when we destroy these old copied mappings.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Fixes: 091d42e43d ("iommu/vt-d: Copy translation tables from old kernel")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5003ae1e735e6bfe4679d9bed6846274f322e77e upstream.
The function device_to_iommu() in the Intel VT-d driver
lacks a NULL-ptr check, resulting in this oops at boot on
some platforms:
BUG: unable to handle kernel NULL pointer dereference at 00000000000007ab
IP: [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
PGD 0
[...]
Call Trace:
? find_or_alloc_domain.constprop.29+0x1a/0x300
? dw_dma_probe+0x561/0x580 [dw_dmac_core]
? __get_valid_domain_for_dev+0x39/0x120
? __intel_map_single+0x138/0x180
? intel_alloc_coherent+0xb6/0x120
? sst_hsw_dsp_init+0x173/0x420 [snd_soc_sst_haswell_pcm]
? mutex_lock+0x9/0x30
? kernfs_add_one+0xdb/0x130
? devres_add+0x19/0x60
? hsw_pcm_dev_probe+0x46/0xd0 [snd_soc_sst_haswell_pcm]
? platform_drv_probe+0x30/0x90
? driver_probe_device+0x1ed/0x2b0
? __driver_attach+0x8f/0xa0
? driver_probe_device+0x2b0/0x2b0
? bus_for_each_dev+0x55/0x90
? bus_add_driver+0x110/0x210
? 0xffffffffa11ea000
? driver_register+0x52/0xc0
? 0xffffffffa11ea000
? do_one_initcall+0x32/0x130
? free_vmap_area_noflush+0x37/0x70
? kmem_cache_alloc+0x88/0xd0
? do_init_module+0x51/0x1c4
? load_module+0x1ee9/0x2430
? show_taint+0x20/0x20
? kernel_read_file+0xfd/0x190
? SyS_finit_module+0xa3/0xb0
? do_syscall_64+0x4a/0xb0
? entry_SYSCALL64_slow_path+0x25/0x25
Code: 78 ff ff ff 4d 85 c0 74 ee 49 8b 5a 10 0f b6 9b e0 00 00 00 41 38 98 e0 00 00 00 77 da 0f b6 eb 49 39 a8 88 00 00 00 72 ce eb 8f <41> f6 82 ab 07 00 00 04 0f 85 76 ff ff ff 0f b6 4d 08 88 0e 49
RIP [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
RSP <ffffc90001457a78>
CR2: 00000000000007ab
---[ end trace 16f974b6d58d0aad ]---
Add the missing pointer check.
Fixes: 1c387188c60f53b338c20eee32db055dfe022a9b ("iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions")
Signed-off-by: Koos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21e722c4c8377b5bc82ad058fed12165af739c1b upstream.
The check to set identity map for tylersburg is done too late. It needs
to be done before the check for identity_map domain is done.
To: Joerg Roedel <joro@8bytes.org>
To: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Cc: Ashok Raj <ashok.raj@intel.com>
Fixes: 86080ccc22 ("iommu/vt-d: Allocate si_domain in init_dmars()")
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Reported-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aec0e86172a79eb5e44aff1055bb953fe4d47c59 upstream.
We met the DMAR fault both on hpsa P420i and P421 SmartArray controllers
under kdump, it can be steadily reproduced on several different machines,
the dmesg log is like:
HP HPSA Driver (v 3.4.16-0)
hpsa 0000:02:00.0: using doorbell to reset controller
hpsa 0000:02:00.0: board ready after hard reset.
hpsa 0000:02:00.0: Waiting for controller to respond to no-op
DMAR: Setting identity map for device 0000:02:00.0 [0xe8000 - 0xe8fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xf4000 - 0xf4fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6e000 - 0xbdf6efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6f000 - 0xbdf7efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf7f000 - 0xbdf82fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf83000 - 0xbdf84fff]
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [02:00.0] fault addr fffff000 [fault reason 06] PTE Read access is not set
hpsa 0000:02:00.0: controller message 03:00 timed out
hpsa 0000:02:00.0: no-op failed; re-trying
After some debugging, we found that the fault addr is from DMA initiated at
the driver probe stage after reset(not in-flight DMA), and the corresponding
pte entry value is correct, the fault is likely due to the old iommu caches
of the in-flight DMA before it.
Thus we need to flush the old cache after context mapping is setup for the
device, where the device is supposed to finish reset at its driver probe
stage and no in-flight DMA exists hereafter.
I'm not sure if the hardware is responsible for invalidating all the related
caches allocated in the iommu hardware before, but seems not the case for hpsa,
actually many device drivers have problems in properly resetting the hardware.
Anyway flushing (again) by software in kdump kernel when the device gets context
mapped which is a quite infrequent operation does little harm.
With this patch, the problematic machine can survive the kdump tests.
CC: Myron Stowe <myron.stowe@gmail.com>
CC: Joseph Szczypek <jszczype@redhat.com>
CC: Don Brace <don.brace@microsemi.com>
CC: Baoquan He <bhe@redhat.com>
CC: Dave Young <dyoung@redhat.com>
Fixes: 091d42e43d21 ("iommu/vt-d: Copy translation tables from old kernel")
Fixes: dbcd861f252d ("iommu/vt-d: Do not re-use domain-ids from the old kernel")
Fixes: cf484d0e6939 ("iommu/vt-d: Mark copied context entries")
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65ca7f5f7d1cdde6c25172fe6107cd16902f826f upstream.
Different encodings are used to represent supported PASID bits
and number of PASID table entries.
The current code assigns ecap_pss directly to extended context
table entry PTS which is wrong and could result in writing
non-zero bits to the reserved fields. IOMMU fault reason
11 will be reported when reserved bits are nonzero.
This patch converts ecap_pss to extend context entry pts encoding
based on VT-d spec. Chapter 9.4 as follows:
- number of PASID bits = ecap_pss + 1
- number of PASID table entries = 2^(pts + 5)
Software assigned limit of pasid_max value is also respected to
match the allocation limitation of PASID table.
cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Fixes: 2f26e0a9c9860 ('iommu/vt-d: Add basic SVM PASID support')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
