| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit c3811a50addd23b9bb5a36278609ee1638debcf6 ]
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc1a ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d99efb229e63928c6b03a756a2e38cd4777fbe8 ]
The VT-d spec Revision 3.3 updated the virtual command registers, virtual
command opcode B register, virtual command response register and virtual
command capability register (Section 10.4.43, 10.4.44, 10.4.45, 10.4.46).
This updates the virtual command interface implementation in the Intel
IOMMU driver accordingly.
Fixes: 24f27d32ab6b7 ("iommu/vt-d: Enlightened PASID allocation")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Sanjay Kumar <sanjay.k.kumar@intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210713042649.3547403-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210818134852.1847070-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8798d36411196da86e70b994725349c16c1119f6 ]
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fixes: 2cd1311a26673 ("iommu/vt-d: Add set domain DOMAIN_ATTR_NESTING attr")
Signed-off-by: Kumar Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Yi Sun <yi.y.sun@intel.com>
Link: https://lore.kernel.org/r/20210817042425.1784279-1-yi.l.liu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9872f9bd9dbd68f75e8db782717d71e8594f6a02 ]
The pasid based IOTLB and devTLB invalidation code is duplicate in
several places. Consolidate them by using the common helpers.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210114085021.717041-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5aa95d8834e07907e64937d792c12ffef7fb271f ]
If probe_device is failing, iommu_group is not initialized because
iommu_group_add_device is not reached, so freeing it will result
in NULL pointer access.
iommu_bus_init
->bus_iommu_probe
->probe_iommu_group in for each:/* return -22 in fail case */
->iommu_probe_device
->__iommu_probe_device /* return -22 here.*/
-> ops->probe_device /* return -22 here.*/
-> iommu_group_get_for_dev
-> ops->device_group
-> iommu_group_add_device //good case
->remove_iommu_group //in fail case, it will remove group
->iommu_release_device
->iommu_group_remove_device // here we don't have group
In my case ops->probe_device (mtk_iommu_probe_device from
mtk_iommu_v1.c) is due to failing fwspec->ops mismatch.
Fixes: d72e31c93746 ("iommu: IOMMU Groups")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210731074737.4573-1-linux@fw-web.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c8f176d6a3fa18aa0f8875da6f7c672ed2a8554 ]
The reference counting issue happens in several exception handling paths
of arm_smmu_iova_to_phys_hard(). When those error scenarios occur, the
function forgets to decrease the refcount of "smmu" increased by
arm_smmu_rpm_get(), causing a refcount leak.
Fix this issue by jumping to "out" label when those error scenarios
occur.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/1623293391-17261-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1adf30f198c26539a62d761e45af72cde570413d ]
arm_smmu_rpm_get() invokes pm_runtime_get_sync(), which increases the
refcount of the "smmu" even though the return value is less than 0.
The reference counting issue happens in some error handling paths of
arm_smmu_rpm_get() in its caller functions. When arm_smmu_rpm_get()
fails, the caller functions forget to decrease the refcount of "smmu"
increased by arm_smmu_rpm_get(), causing a refcount leak.
Fix this issue by calling pm_runtime_resume_and_get() instead of
pm_runtime_get_sync() in arm_smmu_rpm_get(), which can keep the refcount
balanced in case of failure.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/1623293672-17954-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7154cbd31c2069726cf730b0ed94e2e79a221602 upstream.
Compiling the recent dma-iommu changes under 32-bit x86 triggers this
compile warning:
drivers/iommu/dma-iommu.c:249:5: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘phys_addr_t’ {aka ‘unsigned int’} [-Wformat=]
The reason is that %llx is used to print a variable of type
phys_addr_t. Fix it by using the correct %pa format specifier for
phys_addr_t.
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Fixes: 571f316074a20 ("iommu/dma: Fix IOVA reserve dma ranges")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210607124905.27525-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 571f316074a203e979ea90211d9acf423dfe5f46 ]
Fix IOVA reserve failure in the case when address of first memory region
listed in dma-ranges is equal to 0x0.
Fixes: aadad097cd46f ("iommu/dma: Reserve IOVA for PCIe inaccessible DMA address")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20200914072319.6091-1-srinath.mannam@broadcom.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b21a503adf597773e4b37db05db0e9b16a81d53 ]
print_iommu_info prints the EFR register and then the decoded list of
features on a separate line:
pci 0000:00:00.2: AMD-Vi: Extended features (0x206d73ef22254ade):
PPR X2APIC NX GT IA GA PC GA_vAPIC
The second line is emitted via 'pr_cont', which causes it to have a
different ('warn') loglevel compared to the previous line ('info').
Commit 9a295ff0ffc9 attempted to rectify this by removing the newline
from the pci_info format string, but this doesn't work, as pci_info
calls implicitly append a newline anyway.
Printing the decoded features on the same line would make it quite long.
Instead, change pci_info() to pr_info() to omit PCI bus location info,
which is also shown in the preceding message. This results in:
pci 0000:00:00.2: AMD-Vi: Found IOMMU cap 0x40
AMD-Vi: Extended features (0x206d73ef22254ade): PPR X2APIC NX GT IA GA PC GA_vAPIC
AMD-Vi: Interrupt remapping enabled
Fixes: 9a295ff0ffc9 ("iommu/amd: Print extended features in one line to fix divergent log levels")
Link: https://lore.kernel.org/lkml/alpine.LNX.2.20.13.2104112326460.11104@monopod.intra.ispras.ru
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: iommu@lists.linux-foundation.org
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20210504102220.1793-1-amonakov@ispras.ru
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 54c80d907400189b09548039be8f3b6e297e8ae3 ]
When first-level page tables are used for IOVA translation, we use user
privilege by setting U/S bit in the page table entry. This is to make it
consistent with the second level translation, where the U/S enforcement
is not available. Clear the SRE (Supervisor Request Enable) field in the
pasid table entry of RID2PASID so that requests requesting the supervisor
privilege are blocked and treated as DMA remapping faults.
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Suggested-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210512064426.3440915-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210519015027.108468-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 382d91fc0f4f1b13f8a0dcbf7145f4f175b71a18 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Fixes: fa4afd78ea12 ("iommu/virtio: Build virtio-iommu as module")
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210508031451.53493-1-cuibixuan@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0ee74d5a48635c848c20f152d0d488bf84641304 upstream.
iommu_device_sysfs_add() is called before, so is has to be cleaned on subsequent
errors.
Fixes: 39ab9555c2411 ("iommu: Add sysfs bindings for struct iommu_device")
Cc: stable@vger.kernel.org # 4.11.x
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/17411490.HIIP88n32C@mobilepool36.emlix.com
Link: https://lore.kernel.org/r/20210525070802.361755-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eea53c5816889ee8b64544fa2e9311a81184ff9c upstream.
When the first level page table is used for IOVA translation, it only
supports Read-Only and Read-Write permissions. The Write-Only permission
is not supported as the PRESENT bit (implying Read permission) should
always set. When using second level, we still give separate permissions
that allows WriteOnly which seems inconsistent and awkward. We want to
have consistent behavior. After moving to 1st level, we don't want things
to work sometimes, and break if we use 2nd level for the same mappings.
Hence remove this configuration.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8ce9ebbecdfda3322bbcece6b3b25888217f8e3 upstream.
The Access/Dirty bits in the first level page table entry will be set
whenever a page table entry was used for address translation or write
permission was successfully translated. This is always true when using
the first-level page table for kernel IOVA. Instead of wasting hardware
cycles to update the certain bits, it's better to set them up at the
beginning.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210115004202.953965-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 416fa531c8160151090206a51b829b9218b804d9 which is
commit a8ce9ebbecdfda3322bbcece6b3b25888217f8e3 upstream as it was
backported incorrectly and is causing problems for some systems.
Reported-by: Wolfgang Müller <wolf@oriole.systems>
Reported-by: Charles Wright <charles@charleswright.co>
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit c848416cc05afc1589edba04fe00b85c2f797ee3 which is
eea53c5816889ee8b64544fa2e9311a81184ff9c upstream.
Another iommu patch was backported incorrectly, causing problems, so
drop this as well for the moment.
Reported-by: Wolfgang Müller <wolf@oriole.systems>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 994d6608efe4a4c8834bdc5014c86f4bc6aceea6 ]
In early AMD desktop/mobile platforms (during 2013), when the IOMMU
Performance Counter (PMC) support was first introduced in
commit 30861ddc9cca ("perf/x86/amd: Add IOMMU Performance Counter
resource management"), there was a HW bug where the counters could not
be accessed. The result was reading of the counter always return zero.
At the time, the suggested workaround was to add a test logic prior
to initializing the PMC feature to check if the counters can be programmed
and read back the same value. This has been working fine until the more
recent desktop/mobile platforms start enabling power gating for the PMC,
which prevents access to the counters. This results in the PMC support
being disabled unnecesarily.
Unfortunatly, there is no documentation of since which generation
of hardware the original PMC HW bug was fixed. Although, it was fixed
soon after the first introduction of the PMC. Base on this, we assume
that the buggy platforms are less likely to be in used, and it should
be relatively safe to remove this legacy logic.
Link: https://lore.kernel.org/linux-iommu/alpine.LNX.3.20.13.2006030935570.3181@monopod.intra.ispras.ru/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201753
Cc: Tj (Elloe Linux) <ml.linux@elloe.vision>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Alexander Monakov <amonakov@ispras.ru>
Cc: David Coe <david.coe@live.co.uk>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210409085848.3908-3-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 715601e4e36903a653cd4294dfd3ed0019101991 ]
This reverts commit 6778ff5b21bd8e78c8bd547fd66437cf2657fd9b.
The original commit tries to address an issue, where PMC power-gating
causing the IOMMU PMC pre-init test to fail on certain desktop/mobile
platforms where the power-gating is normally enabled.
There have been several reports that the workaround still does not
guarantee to work, and can add up to 100 ms (on the worst case)
to the boot process on certain platforms such as the MSI B350M MORTAR
with AMD Ryzen 3 2200G.
Therefore, revert this commit as a prelude to removing the pre-init
test.
Link: https://lore.kernel.org/linux-iommu/alpine.LNX.3.20.13.2006030935570.3181@monopod.intra.ispras.ru/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201753
Cc: Tj (Elloe Linux) <ml.linux@elloe.vision>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Alexander Monakov <amonakov@ispras.ru>
Cc: David Coe <david.coe@live.co.uk>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210409085848.3908-2-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 304c73ba69459d4c18c2a4b843be6f5777b4b85c ]
Currently, on the Dell OptiPlex 5055 the EFR mismatch warning looks like
below.
[ 1.479774] smpboot: CPU0: AMD Ryzen 5 PRO 1500 Quad-Core Processor (family: 0x17, model: 0x1, stepping: 0x1)
[…]
[ 2.507370] AMD-Vi: [Firmware Warn]: EFR mismatch. Use IVHD EFR (0xf77ef22294ada : 0x400f77ef22294ada
).
Add the newline after the `).`, so it’s on one line.
Fixes: a44092e326d4 ("iommu/amd: Use IVHD EFR for early initialization of IOMMU features")
Cc: iommu@lists.linux-foundation.org
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Robert Richter <rrichter@amd.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20210412180141.29605-1-pmenzel@molgen.mpg.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c0474a606ecb9326227b4d68059942f9db88a897 ]
When the Intel IOMMU is operating in the scalable mode, some information
from the root and context table may be used to tag entries in the PASID
cache. Software should invalidate the PASID-cache when changing root or
context table entries.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: 7373a8cc38197 ("iommu/vt-d: Setup context and enable RID2PASID support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eea53c5816889ee8b64544fa2e9311a81184ff9c ]
When the first level page table is used for IOVA translation, it only
supports Read-Only and Read-Write permissions. The Write-Only permission
is not supported as the PRESENT bit (implying Read permission) should
always set. When using second level, we still give separate permissions
that allows WriteOnly which seems inconsistent and awkward. We want to
have consistent behavior. After moving to 1st level, we don't want things
to work sometimes, and break if we use 2nd level for the same mappings.
Hence remove this configuration.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8ce9ebbecdfda3322bbcece6b3b25888217f8e3 ]
The Access/Dirty bits in the first level page table entry will be set
whenever a page table entry was used for address translation or write
permission was successfully translated. This is always true when using
the first-level page table for kernel IOVA. Instead of wasting hardware
cycles to update the certain bits, it's better to set them up at the
beginning.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210115004202.953965-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03d205094af45bca4f8e0498c461a893aa3ec6d9 ]
The Address field of the Page Request Descriptor only keeps bit [63:12]
of the offending address. Convert it to a full address before reporting
it to device drivers.
Fixes: eb8d93ea3c1d3 ("iommu/vt-d: Report page request faults for guest SVA")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320025415.641201-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c00612d0cba10f7d0917cf1f73c945003ed4cd7 ]
The Intel VT-d driver checks wrong register to report snoop capablility
when using first level page table for GPA to HPA translation. This might
lead the IOMMU driver to say that it supports snooping control, but in
reality, it does not. Fix this by always setting PASID-table-entry.PGSNP
whenever a pasid entry is setting up for GPA to HPA translation so that
the IOMMU driver could report snoop capability as long as it runs in the
scalable mode.
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level")
Suggested-by: Rajesh Sankaran <rajesh.sankaran@intel.com>
Suggested-by: Kevin Tian <kevin.tian@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210330021145.13824-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d421058c815d54113d9afdf6db3f995c788cf0d ]
The VT-d specification (section 7.6) requires that the value in the
Private Data field of a Page Group Response Descriptor must match
the value in the Private Data field of the respective Page Request
Descriptor.
The private data field of a page group response descriptor is set then
immediately cleared in prq_event_thread(). This breaks the rule defined
by the VT-d specification. Fix it by moving clearing code up.
Fixes: 5b438f4ba315d ("iommu/vt-d: Support page request in scalable mode")
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210320024156.640798-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 655c447c97d7fe462e6cd9e15809037be028bc70 ]
In arm_smmu_gerror_handler(), the value of the SMMU_GERROR register is
filtered by GERROR_ERR_MASK. However, the GERROR_ERR_MASK does not contain
the SFM bit. As a result, the subsequent error processing is not performed
when only the SFM error occurs.
Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reported-by: Rui Zhu <zhurui3@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210324081603.1074-1-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78a523fe73b81b4447beb2d6c78c9fafae24eebb ]
When supervisor/privilige mode SVM is used, we bind init_mm.pgd with
a supervisor PASID. There should not be any page fault for init_mm.
Execution request with DMA read is also not supported.
This patch checks PRQ descriptor for both unsupported configurations,
reject them both with invalid responses.
Fixes: 1c4f88b7f1f92 ("iommu/vt-d: Shared virtual address in scalable mode")
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-4-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9abb19fa5fd2d8a4be61c6cd4b2a48aa1a17f9c ]
The device iommu probe/attach might have failed leaving dev->iommu
to NULL and device drivers may still invoke these functions resulting
in a crash in iommu vendor driver code.
Hence make sure we check that.
Fixes: a3a195929d40 ("iommu: Add APIs for multiple domains per device")
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210303173611.520-1-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6778ff5b21bd8e78c8bd547fd66437cf2657fd9b ]
Certain AMD platforms enable power gating feature for IOMMU PMC,
which prevents the IOMMU driver from updating the counter while
trying to validate the PMC functionality in the init_iommu_perf_ctr().
This results in disabling PMC support and the following error message:
"AMD-Vi: Unable to read/write to IOMMU perf counter"
To workaround this issue, disable power gating temporarily by programming
the counter source to non-zero value while validating the counter,
and restore the prior state afterward.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Tj (Elloe Linux) <ml.linux@elloe.vision>
Link: https://lore.kernel.org/r/20210208122712.5048-1-suravee.suthikulpanit@amd.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201753
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28a77185f1cd0650b664f54614143aaaa3a7a615 ]
It is incorrect to always clear PRO when it's set w/o first checking
whether the overflow condition has been cleared. Current code assumes
that if an overflow condition occurs it must have been cleared by earlier
loop. However since the code runs in a threaded context, the overflow
condition could occur even after setting the head to the tail under some
extreme condition. To be sane, we should read both head/tail again when
seeing a pending PRO and only clear PRO after all pending PRs have been
handled.
Suggested-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/linux-iommu/MWHPR11MB18862D2EA5BD432BF22D99A48CA09@MWHPR11MB1886.namprd11.prod.outlook.com/
Link: https://lore.kernel.org/r/20210126080730.2232859-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 140456f994195b568ecd7fc2287a34eadffef3ca upstream.
increase_address_space() calls get_zeroed_page(gfp) under spin_lock with
disabled interrupts. gfp flags passed to increase_address_space() may allow
sleeping, so it comes to this:
BUG: sleeping function called from invalid context at mm/page_alloc.c:4342
in_atomic(): 1, irqs_disabled(): 1, pid: 21555, name: epdcbbf1qnhbsd8
Call Trace:
dump_stack+0x66/0x8b
___might_sleep+0xec/0x110
__alloc_pages_nodemask+0x104/0x300
get_zeroed_page+0x15/0x40
iommu_map_page+0xdd/0x3e0
amd_iommu_map+0x50/0x70
iommu_map+0x106/0x220
vfio_iommu_type1_ioctl+0x76e/0x950 [vfio_iommu_type1]
do_vfs_ioctl+0xa3/0x6f0
ksys_ioctl+0x66/0x70
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x4e/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by moving get_zeroed_page() out of spin_lock/unlock section.
Fixes: 754265bcab ("iommu/amd: Fix race in increase_address_space()")
Signed-off-by: Andrey Ryabinin <arbn@yandex-team.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210217143004.19165-1-arbn@yandex-team.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrey Ryabinin <arbn@yandex-team.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 444d66a23c1f1e4c4d12aed4812681d0ad835d60 ]
As per Intel vt-d spec, Rev 3.0 (section 10.4.45 "Virtual Command Response
Register"), the status code of "No PASID available" error in response to
the Allocate PASID command is 2, not 1. The same for "Invalid PASID" error
in response to the Free PASID command.
We will otherwise see confusing kernel log under the command failure from
guest side. Fix it.
Fixes: 24f27d32ab6b ("iommu/vt-d: Enlightened PASID allocation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210227073909.432-1-yuzenghui@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dead723e6f049e9fb6b05e5b93456982798ea961 upstream.
When extracting the mask for a SMR that was programmed by the
bootloader, the SMR's valid bit is also extracted and is treated
as part of the mask, which is not correct. Consider the scenario
where an SMMU master whose context is determined by a bootloader
programmed SMR is removed (omitting parts of device/driver core):
->iommu_release_device()
-> arm_smmu_release_device()
-> arm_smmu_master_free_smes()
-> arm_smmu_free_sme() /* Assume that the SME is now free */
-> arm_smmu_write_sme()
-> arm_smmu_write_smr() /* Construct SMR value using mask and SID */
Since the valid bit was considered as part of the mask, the SMR will
be programmed as valid.
Fix the SMR mask extraction step for bootloader programmed SMRs
by masking out the valid bit when we know that we're already
working with a valid SMR.
Fixes: 07a7f2caaa5a ("iommu/arm-smmu-qcom: Read back stream mappings")
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
Cc: stable@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1611611545-19055-1-git-send-email-isaacm@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8437a3ef8c485903d05d1f261328aaf0c0a6cc2 ]
Sleeping while atomic = bad. Let's fix an obvious typo to try to avoid it.
The warning that was seen (on a downstream kernel with the problematic
patch backported):
BUG: sleeping function called from invalid context at mm/page_alloc.c:4726
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 9, name: ksoftirqd/0
CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 5.4.93-12508-gc10c93e28e39 #1
Call trace:
dump_backtrace+0x0/0x154
show_stack+0x20/0x2c
dump_stack+0xa0/0xfc
___might_sleep+0x11c/0x12c
__might_sleep+0x50/0x84
__alloc_pages_nodemask+0xf8/0x2bc
__arm_lpae_alloc_pages+0x48/0x1b4
__arm_lpae_map+0x124/0x274
__arm_lpae_map+0x1cc/0x274
arm_lpae_map+0x140/0x170
arm_smmu_map+0x78/0xbc
__iommu_map+0xd4/0x210
_iommu_map+0x4c/0x84
iommu_map_atomic+0x44/0x58
__iommu_dma_map+0x8c/0xc4
iommu_dma_map_page+0xac/0xf0
Fixes: d8c1df02ac7f ("iommu: Move iotlb_sync_map out from __iommu_map")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210201170611.1.I64a7b62579287d668d7c89e105dcedf45d641063@changeid
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8c1df02ac7f2c802a9b2afc0f5c888c4217f1d5 ]
In the end of __iommu_map, It alway call iotlb_sync_map.
This patch moves iotlb_sync_map out from __iommu_map since it is
unnecessary to call this for each sg segment especially iotlb_sync_map
is flush tlb all currently. Add a little helper _iommu_map for this.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107122909.16317-2-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 862c3715de8f3e5350489240c951d697f04bd8c9 ]
Currently gather->end is "unsigned long" which may be overflow in
arch32 in the corner case: 0xfff00000 + 0x100000(iova + size).
Although it doesn't affect the size(end - start), it affects the checking
"gather->end < end"
This patch changes this "end" to the real end address
(end = start + size - 1). Correspondingly, update the length to
"end - start + 1".
Fixes: a7d20dc19d9e ("iommu: Introduce struct iommu_iotlb_gather for batching TLB flushes")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107122909.16317-5-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 29b32839725f8c89a41cb6ee054c85f3116ea8b5 upstream.
When an Intel IOMMU is virtualized, and a physical device is
passed-through to the VM, changes of the virtual IOMMU need to be
propagated to the physical IOMMU. The hypervisor therefore needs to
monitor PTE mappings in the IOMMU page-tables. Intel specifications
provide "caching-mode" capability that a virtual IOMMU uses to report
that the IOMMU is virtualized and a TLB flush is needed after mapping to
allow the hypervisor to propagate virtual IOMMU mappings to the physical
IOMMU. To the best of my knowledge no real physical IOMMU reports
"caching-mode" as turned on.
Synchronizing the virtual and the physical IOMMU tables is expensive if
the hypervisor is unaware which PTEs have changed, as the hypervisor is
required to walk all the virtualized tables and look for changes.
Consequently, domain flushes are much more expensive than page-specific
flushes on virtualized IOMMUs with passthrough devices. The kernel
therefore exploited the "caching-mode" indication to avoid domain
flushing and use page-specific flushing in virtualized environments. See
commit 78d5f0f500e6 ("intel-iommu: Avoid global flushes with caching
mode.")
This behavior changed after commit 13cf01744608 ("iommu/vt-d: Make use
of iova deferred flushing"). Now, when batched TLB flushing is used (the
default), full TLB domain flushes are performed frequently, requiring
the hypervisor to perform expensive synchronization between the virtual
TLB and the physical one.
Getting batched TLB flushes to use page-specific invalidations again in
such circumstances is not easy, since the TLB invalidation scheme
assumes that "full" domain TLB flushes are performed for scalability.
Disable batched TLB flushes when caching-mode is on, as the performance
benefit from using batched TLB invalidations is likely to be much
smaller than the overhead of the virtual-to-physical IOMMU page-tables
synchronization.
Fixes: 13cf01744608 ("iommu/vt-d: Make use of iova deferred flushing")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210127175317.1600473-1-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 728da60da7c1ec1e21ae64648e376666de3c279c upstream.
Midgard GPUs have ACE-Lite master interfaces which allows systems to
integrate them in an I/O-coherent manner. It seems that from the GPU's
viewpoint, the rest of the system is its outer shareable domain, and so
even when snoop signals are wired up, they are only emitted for outer
shareable accesses. As such, setting the TTBR_SHARE_OUTER bit does
indeed get coherent pagetable walks working nicely for the coherent
T620 in the Arm Juno SoC.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8df778355378127ea7eccc9521d6427e3e48d4f2.1600780574.git.robin.murphy@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 494b3688bb11a21af12e92a344a1313486693d47 ]
An incorrect address mask is being used in the qi_flush_dev_iotlb_pasid()
to check the address alignment. This leads to a lot of spurious kernel
warnings:
[ 485.837093] DMAR: Invalidate non-aligned address 7f76f47f9000, order 0
[ 485.837098] DMAR: Invalidate non-aligned address 7f76f47f9000, order 0
[ 492.494145] qi_flush_dev_iotlb_pasid: 5734 callbacks suppressed
[ 492.494147] DMAR: Invalidate non-aligned address 7f7728800000, order 11
[ 492.508965] DMAR: Invalidate non-aligned address 7f7728800000, order 11
Fix it by checking the alignment in right way.
Fixes: 288d08e780088 ("iommu/vt-d: Handle non-page aligned address")
Reported-and-tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Liu Yi L <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20210119043500.1539596-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a44092e326d403c7878018ba532369f84d31dbfa ]
IOMMU Extended Feature Register (EFR) is used to communicate
the supported features for each IOMMU to the IOMMU driver.
This is normally read from the PCI MMIO register offset 0x30,
and used by the iommu_feature() helper function.
However, there are certain scenarios where the information is needed
prior to PCI initialization, and the iommu_feature() function is used
prematurely w/o warning. This has caused incorrect initialization of IOMMU.
This is the case for the commit 6d39bdee238f ("iommu/amd: Enforce 4k
mapping for certain IOMMU data structures")
Since, the EFR is also available in the IVHD header, and is available to
the driver prior to PCI initialization. Therefore, default to using
the IVHD EFR instead.
Fixes: 6d39bdee238f ("iommu/amd: Enforce 4k mapping for certain IOMMU data structures")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/20210120135002.2682-1-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2d6ffc63f12417b979955a5b22ad9a76d2af5de9 upstream.
The VT-d hardware will ignore those Addr bits which have been masked by
the AM field in the PASID-based-IOTLB invalidation descriptor. As the
result, if the starting address in the descriptor is not aligned with
the address mask, some IOTLB caches might not invalidate. Hence people
will see below errors.
[ 1093.704661] dmar_fault: 29 callbacks suppressed
[ 1093.704664] DMAR: DRHD: handling fault status reg 3
[ 1093.712738] DMAR: [DMA Read] Request device [7a:02.0] PASID 2
fault addr 7f81c968d000 [fault reason 113]
SM: Present bit in first-level paging entry is clear
Fix this by using aligned address for P |
