| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 774514bf977377c9137640a0310bd64eed0f7323 upstream.
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Fixes: 94fe2580a2f3 ("mmc: core: Enable erase/discard/trim support for all mmc hosts")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210225145454.12780-1-yann.gautier@foss.st.com
Cc: stable@vger.kernel.org
[Ulf: Simplified the code and extended the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5b1c6dc13daec60405ecd31eaa5379a9f798fa8 ]
The device_* calls were added a few years ago to abstract
DT/ACPI/fwnode firmware interfaces. Lets convert the two
sdhci caps fields to use the generic calls rather than the OF
specific ones. This has the side effect of allowing
ACPI based devices to quirk themselves when the caps field
is broken.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201120233831.447365-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f9833d3ec8da34861cd0680b00c73e653877eb9 ]
The RPi4 has an Arasan controller it carries over from the RPi3 and a newer
eMMC2 controller. Because of a couple of quirks, it seems wiser to bind
these controllers to the same driver that DT is using on this platform
rather than the generic sdhci_acpi driver with PNP0D40.
So, BCM2847 describes the older Arasan and BRCME88C describes the newer
eMMC2. The older Arasan is reusing an existing ACPI _HID used by other OSes
booting these tables on the RPi.
With this change, Linux is capable of utilizing the SD card slot, and the
Wi-Fi when booted with UEFI+ACPI on the RPi4.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120000406.1843400-2-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ]
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0bb7e560f821c7770973a94e346654c4bdccd42c ]
If 'mmc_of_parse()' fails, we must undo the previous 'dma_request_chan()'
call.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201208203527.49262-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f7dfda4f2cec580c135fd81d96a05006651c128 ]
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1ad9f88014ae1d5abccb6fe930bc4c5c311bdc05 upstream.
Force chip enter L0 power state during SDR104 HW tuning to avoid tuning failure
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Link: https://lore.kernel.org/r/20210206014051.3418-1-shirley.her@bayhubtech.com
Fixes: 7b7d897e8898 ("mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a56f44138a2c57047f1ea94ea121af31c595132b upstream.
In sdhci_esdhc_imx_remove() the SDHCI_INT_STATUS in read. Under some
circumstances, this may be done while the device is runtime suspended,
triggering the below splat.
Fix the problem by adding a pm_runtime_get_sync(), before reading the
register, which will turn on clocks etc making the device accessible again.
[ 1811.323148] mmc1: card aaaa removed
[ 1811.347483] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
[ 1811.354988] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core [last unloaded: mmc_core]
[ 1811.365726] CPU: 0 PID: 3464 Comm: rmmod Not tainted 5.10.1-sd-99871-g53835a2e8186 #5
[ 1811.373559] Hardware name: Freescale i.MX8DXL EVK (DT)
[ 1811.378705] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 1811.384723] pc : sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx]
[ 1811.391090] lr : platform_drv_remove+0x2c/0x50
[ 1811.395536] sp : ffff800012c7bcb0
[ 1811.398855] x29: ffff800012c7bcb0 x28: ffff00002c72b900
[ 1811.404181] x27: 0000000000000000 x26: 0000000000000000
[ 1811.409497] x25: 0000000000000000 x24: 0000000000000000
[ 1811.414814] x23: ffff0000042b3890 x22: ffff800009127120
[ 1811.420131] x21: ffff00002c4c9580 x20: ffff0000042d0810
[ 1811.425456] x19: ffff0000042d0800 x18: 0000000000000020
[ 1811.430773] x17: 0000000000000000 x16: 0000000000000000
[ 1811.436089] x15: 0000000000000004 x14: ffff000004019c10
[ 1811.441406] x13: 0000000000000000 x12: 0000000000000020
[ 1811.446723] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
[ 1811.452040] x9 : fefefeff6364626d x8 : 7f7f7f7f7f7f7f7f
[ 1811.457356] x7 : 78725e6473607372 x6 : 0000000080808080
[ 1811.462673] x5 : 0000000000000000 x4 : 0000000000000000
[ 1811.467990] x3 : ffff800011ac1cb0 x2 : 0000000000000000
[ 1811.473307] x1 : ffff8000091214d4 x0 : ffff8000133a0030
[ 1811.478624] Call trace:
[ 1811.481081] sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx]
[ 1811.487098] platform_drv_remove+0x2c/0x50
[ 1811.491198] __device_release_driver+0x188/0x230
[ 1811.495818] driver_detach+0xc0/0x14c
[ 1811.499487] bus_remove_driver+0x5c/0xb0
[ 1811.503413] driver_unregister+0x30/0x60
[ 1811.507341] platform_driver_unregister+0x14/0x20
[ 1811.512048] sdhci_esdhc_imx_driver_exit+0x1c/0x3a8 [sdhci_esdhc_imx]
[ 1811.518495] __arm64_sys_delete_module+0x19c/0x230
[ 1811.523291] el0_svc_common.constprop.0+0x78/0x1a0
[ 1811.528086] do_el0_svc+0x24/0x90
[ 1811.531405] el0_svc+0x14/0x20
[ 1811.534461] el0_sync_handler+0x1a4/0x1b0
[ 1811.538474] el0_sync+0x174/0x180
[ 1811.541801] Code: a9025bf5 f9403e95 f9400ea0 9100c000 (b9400000)
[ 1811.547902] ---[ end trace 3fb1a3bd48ff7be5 ]---
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org # v4.0+
Link: https://lore.kernel.org/r/20210210181933.29263-1-Frank.Li@nxp.com
[Ulf: Clarified the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d7aefb2887601cf1fc3f86f55d43b2c9aece5e8f ]
According to the latest datasheet, the internal DMAC buffer alignment
R-Car Gen3 SDHI HW should be 128-bytes. So, fix it.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: revise commit description, rebase]
Fixes: 2a68ea7896e3 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ]
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c9c256a8b0dc09c305c409d6264cc016af2ba38d ]
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
remove function
[ Upstream commit 5d15cbf63515c6183d2ed7c9dd0586b4db23ffb1 ]
'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.
Add the missing call both in the error handling path of the probe function
and in the remove function.
Fixes: ff65ffe46d28 ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d7fb9c24209556478e65211d7a1f056f2d43cceb upstream.
The implementation of sdhci_pltfm_suspend() is only available when
CONFIG_PM_SLEEP is set, which triggers a linking error:
"undefined symbol: sdhci_pltfm_suspend" when building sdhci-brcmstb.c.
Fix this by implementing the missing stubs when CONFIG_PM_SLEEP is unset.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 5b191dcba719 ("mmc: sdhci-brcmstb: Fix mmc timeout errors on S5 suspend")
Cc: stable@vger.kernel.org
Tested-By: Nicolas Schichan <nschichan@freeebox.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b191dcba719319148eeecf6ed409949fac55b39 upstream.
Commit e7b5d63a82fe ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82fe ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a3ed0dc3594d99ff341ec63865a40519ea24b8d upstream.
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca1219c0a7432272324660fc9f61a9940f90c50b upstream.
Commit a44f7cb93732 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb93732 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d7b819b5d33869d41bdaa427aeb98ae24c57a38b ]
Fix to return the error code from devm_gpiod_get_optional() instaed
of 0 in pxamci_probe().
Fixes: f54005b508b9a9d9c ("mmc: pxa: Use GPIO descriptor for power")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20201121021431.3168506-1-chengzhihao1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fcc541fea394d67ad607ee41acfa891e79fe17a2 ]
'busy_timeout' is in msecs, not in jiffies. Use the correct factor.
Fixes: 5e958e4aacf4 ("sdhci: tegra: Implement Tegra specific set_timeout callback")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201116132206.23518-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac575 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Further testing of error cases revealed that downgrade is not enough, so
we need to reset the SCC which is done by calling the custom reset
function. This reset function can distinguish between the various SDHI
variants, so protecting the call with MIN_RCAR2 is enough here.
Fixes: 24ce2d7b8bea ("mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125204953.3344-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 16ada730a759 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae86 ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae86 ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDIO recheck fix is required for more of the supported variants. Let's
add it to those that needs it.
Reported-by: Fabien Parent <fparent@baylibre.com>
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/20201119030237.9414-1-yong.mao@mediatek.com
Fixes: 9e2582e57407 ("mmc: mediatek: fix SDIO irq issue")
Cc: stable@vger.kernel.org
[Ulf: Clarified commitmsg ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Before we got these errors on MT8192 platform:
[ 59.153891] Restarting tasks ...
[ 59.154540] done.
[ 59.159175] PM: suspend exit
[ 59.218724] mtk-msdc 11f60000.mmc: phase: [map:fffffffe] [maxlen:31]
[final:16]
[ 119.776083] mmc0: cqhci: timeout for tag 9
[ 119.780196] mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
[ 119.786709] mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
[ 119.793225] mmc0: cqhci: Config: 0x00000101 | Control: 0x00000000
[ 119.799706] mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000000
[ 119.806177] mmc0: cqhci: Int sig: 0x00000000 | Int Coal: 0x00000000
[ 119.812670] mmc0: cqhci: TDL base: 0x00000000 | TDL up32: 0x00000000
[ 119.819149] mmc0: cqhci: Doorbell: 0x003ffc00 | TCN: 0x00000200
[ 119.825656] mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
[ 119.832155] mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
[ 119.838627] mmc0: cqhci: SSC2: 0x00000000 | DCMD rsp: 0x00000000
[ 119.845174] mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x0000891c
[ 119.851654] mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
[ 119.865773] mmc0: cqhci: : ===========================================
[ 119.872358] mmc0: running CQE recovery
From these logs, we found TDL base was back to the default value.
After suspend, the mmc host is powered off by HW, and bring CQE register
to the default value, so we add system suspend/resume interface, then bring
CQE to deactivated state before suspend, it will be enabled by CQE first
request after resume.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Link: https://lore.kernel.org/r/20201118063405.24906-1-wenbin.mei@mediatek.com
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
[Ulf: Renamed functions]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the current implementation DLL reset will be issued for
each ITAP and OTAP setting inside ATF, this is creating issues
in some scenarios and this sequence is not inline with the TRM.
To fix the issue, DLL reset should be removed from the ATF and
host driver will request it explicitly.
This patch update host driver to explicitly request for DLL reset
before ITAP (assert DLL) and after OTAP (release DLL) settings.
Fixes: a5c8b2ae2e51 ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Mask the ITAP and OTAP delay bits before updating with the new
tap value for Versal platform.
Fixes: 1a470721c8f5 ("sdhci: arasan: Add support for Versal Tap Delays")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Allow configuring the Output and Input tap values with zero to avoid
failures in some cases (one of them is SD boot mode) where the output
and input tap values may be already set to non-zero.
Fixes: a5c8b2ae2e51 ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
controllers
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7d16e ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit db1af1e9712920f47b5dc6a995fca3eec05ea85e. It was
only a workaround to hide a regression. We now have proper fixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When powering off a card, we need to disable the tuning HW (like SCC for
the Renesas SDHI) to get to a sane state and allow for re-tuning new
cards. This was hidden before because we wrongly did that in hw_reset()
before which was an unintended use of hw_reset(). Now that we corrected
the use of hw_reset() meanwhile, we revealed this shortcoming and need
to fix it properly by explicitly calling the downgrade callback.
Fixes: 6e7d4de10890 ("mmc: renesas_sdhi: move wrong 'hw_reset' to 'reset'")
Suggested-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When applying a revert, the assumption that DMA only needs to be cleared
in specific cases was wrong. We want to reset the DMA controller every
time the rest of the HW gets reset, too.
Fixes: 34e3211e5492 ("Revert "mmc: tmio: fix reset operation"")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Apply erratum workaround of unreliable pulse width detection to
more affected platforms (LX2160A Rev2.0 and LS1028A Rev1.0).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes: 48e304cc1970 ("mmc: sdhci-of-esdhc: workaround for unreliable pulse width detection")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110071314.3868-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
added tmio_mmc_host_free(), but missed the function calling in
the sh_mobile_sdhi_remove() at that time. So, fix it. Otherwise,
we cannot rebind the sdhi/mmc devices when we use aliases of mmc.
Fixes: 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604654730-29914-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- sdhci: Fix performance regression with auto CMD auto select
- sdhci-of-esdhc: Fix initialization for eMMC HS400 mode
- sdhci-of-esdhc: Fix timeout bug for tuning commands
* tag 'mmc-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-esdhc: make sure delay chain locked for HS400
mmc: sdhci-of-esdhc: set timeout to max before tuning
mmc: sdhci: Use Auto CMD Auto Select only when v4_mode is true
|
|
For eMMC HS400 mode initialization, the DLL reset is a required step
if DLL is enabled to use previously, like in bootloader.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201020081116.20918-1-yangbo.lu@nxp.com
Fixes: 54e08d9a95ca ("mmc: sdhci-of-esdhc: add hs400 mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
On rare occations there is the following error:
mmc0: Tuning timeout, falling back to fixed sampling clock
There are SD cards which takes a significant longer time to reply to the
first CMD19 command. The eSDHC takes the data timeout value into account
during the tuning period. The SDHCI core doesn't explicitly set this
timeout for the tuning procedure. Thus on the slow cards, there might be
a spurious "Buffer Read Ready" interrupt, which in turn triggers a wrong
sequence of events. In the end this will lead to an unsuccessful tuning
procedure and to the above error.
To workaround this, set the timeout to the maximum value (which is the
best we can do) and the SDHCI core will take care of the proper timeout
handling.
Fixes: ba49cbd0936e ("mmc: sdhci-of-esdhc: add tuning support")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201022222337.19857-1-michael@walle.cc
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci-of-dwcmshc meets an eMMC read performance regression with below
command after commit 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto
Select support"):
dd if=/dev/mmcblk0 of=/dev/null bs=8192 count=100000
Before the commit, the above command gives 120MB/s
After the commit, the above command gives 51.3 MB/s
So it looks like sdhci-of-dwcmshc expects Version 4 Mode for Auto
CMD Auto Select. Fix the performance degradation by ensuring v4_mode
is true to use Auto CMD Auto Select.
Fixes: 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto Select support")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201015174115.4cf2c19a@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a MODULE_DEVICE_TABLE() entry so that the driver is autoloaded
when built as a module.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20201008100129.13917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After the conversions of the reset routines, re-inserting SD cards
didn't work anymore. Apply this temporary workaround to have working SD
cards during the merge window. The issue will be fixed properly until
the final release.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201008092533.76588-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add CQHCI initialization and implement CQHCI operations for GL9763E.
Use bit19 of the register (0x888) to decide whether to disable command
queuing. If the bit is set, the command queuing will be disabled.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201005105509.11343-1-ben.chuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the SW tuning App note[1], tuning is required for all
UHS speed modes. Tuning for SDR50 is not enabled in Capabilities by
default so enable it from the CTL_CFG registers.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
With this addition, make sure that DLL is always switched off at the
beginning of the set_clock() call to simplify configuration. This also
removes the need for the dll_on member in struct sdhci_am654_data.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Change hard coded array size value to depend on struct timing_data
array size.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The bit ESDHC_PERIPHERAL_CLK_SEL to select using peripheral clock
or platform clock is not able to be reset by SDHCI_RESET_ALL.
So driver needs to initialize it as 1 or 0 once, to override the
different value which may be configured in bootloader.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200927082304.9232-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix build errors for meson-gx-mmc.c when CONFIG_COMMON_CLK is not
set/enabled. This can happen when COMPILE_TEST is set/enabled.
ERROR: modpost: "clk_divider_ops" [drivers/mmc/host/meson-gx-mmc.ko] undefined!
ERROR: modpost: "devm_clk_register" [drivers/mmc/host/meson-gx-mmc.ko] undefined!
ERROR: modpost: "clk_mux_ops" [drivers/mmc/host/meson-gx-mmc.ko] undefined!
ERROR: modpost: "__clk_get_name" [drivers/mmc/host/meson-gx-mmc.ko] undefined!
Fixes: 54d8454436a2 ("mmc: host: Enable compile testing of multiple drivers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200925164323.29843-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
Commit bedf9fc01ff1 ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS |
