| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 54309fde1a352ad2674ebba004a79f7d20b9f037 upstream.
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed946c ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40c67c291a93f8846c4a972c9ef1b7ba4544c8d0 upstream.
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Fixes: 5552d7ad596c ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd2db32e7c3e35bd4d9b8bbff689434a50893546 upstream.
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: Xin Xiong <xiongx18@fudan.edu.cn>
Cc: Xin Tan <tanxin.ctf@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Cc: linux-mmc@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Reported-by: whitehat002 <hackyzh002@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c3e5b74b9e2146f564905e50ca716591c76d4f1 ]
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fc9a77bc64e1f23d07953439817d8402ac9706f ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoC")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-3-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 77bed755e0f06135faccdd3948863703f9a6e640 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-2-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e53e97f805cb1abeea000a61549d42f92cb10804 upstream.
Add PCI ID for Intel ADL eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211124094850.1783220-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff31ee0a0f471776f67be5e5275c18d17736fc6b upstream.
During test campaign, and especially after several unbind/bind sequences,
it has been seen that the SD-card on SDMMC1 thread could freeze.
The freeze always appear on a CMD23 following a CMD19.
Checking SDMMC internal registers shows that the tuning command (CMD19)
has failed.
The freeze is then due to the delay block involved in the tuning sequence.
To correct this, clear the delay block register DLYB_CR register after
the tuning commands.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 1103f807a3b9 ("mmc: mmci_sdmmc: Add execute tuning with delay block")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211215141727.4901-4-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66c915d09b942fb3b2b0cb2f56562180901fba17 upstream.
It's seems prone to problems by allowing card detect and its corresponding
mmc_rescan() work to run, during platform shutdown. For example, we may end
up turning off the power while initializing a card, which potentially could
damage it.
To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host
class device and then turn of the card detect from there.
Reported-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211203141555.105351-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f89b548ca66be7500dcd92ee8e61590f7d08ac91 upstream.
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970ef96 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fc7261dbab139d3c64c3b618262504e16cfe7ee upstream.
When CMD13 is sent after switching to HS400ES mode, the bus
is operating at either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR.
To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI
interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host
controller CAR clock and the interface clock are rate matched.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: dfc9700cef77 ("mmc: tegra: Implement HS400 enhanced strobe")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211214113653.4631-1-pshete@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7dba402807a85fa3723f4a27504813caf81cc9d7 upstream.
'cmd_error' is not necessarily initialized on some error paths in
mmc_send_tuning(). Initialize it.
Fixes: 2c9017d0b5d3 ("mmc: renesas_sdhi: abort tuning when timeout detected")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211130132309.18246-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d7c194b7c9ad414264935ad4f943a6ce285ebb1 upstream.
The block layer forces a minimum segment size of PAGE_SIZE, so a segment
can be too big for the ADMA table, if PAGE_SIZE >= 64KiB. Fix by writing
multiple descriptors, noting that the ADMA table is sized for 4KiB chunks
anyway, so it will be big enough.
Reported-and-tested-by: Bough Chen <haibo.chen@nxp.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211115082345.802238-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit adab993c25191b839b415781bdc7173a77315240 upstream.
On IMX SoC's which support CMDQ the following can occur during high a
high cpu load:
mmc2: cqhci: ============ CQHCI REGISTER DUMP ===========
mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510
mmc2: cqhci: Config: 0x00001001 | Control: 0x00000000
mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
mmc2: cqhci: TDL base: 0x8003f000 | TDL up32: 0x00000000
mmc2: cqhci: Doorbell: 0xbf01dfff | TCN: 0x00000000
mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x08000000
mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000
mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000800
mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
mmc2: cqhci: Resp idx: 0x0000000d | Resp arg: 0x00000000
mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc2: sdhci: Sys addr: 0x7c722000 | Version: 0x00000002
mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000020
mmc2: sdhci: Argument: 0x00018000 | Trn mode: 0x00000023
mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000030
mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080
mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f
mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000
mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000
mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000502
mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407
mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff
mmc2: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0xffc003ff
mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d07f01
mmc2: sdhci: Host ctl2: 0x00000088
mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0xfe179020
mmc2: sdhci-esdhc-imx: ========= ESDHC IMX DEBUG STATUS DUMP ====
mmc2: sdhci-esdhc-imx: cmd debug status: 0x2120
mmc2: sdhci-esdhc-imx: data debug status: 0x2200
mmc2: sdhci-esdhc-imx: trans debug status: 0x2300
mmc2: sdhci-esdhc-imx: dma debug status: 0x2400
mmc2: sdhci-esdhc-imx: adma debug status: 0x2510
mmc2: sdhci-esdhc-imx: fifo debug status: 0x2680
mmc2: sdhci-esdhc-imx: async fifo debug status: 0x2750
mmc2: sdhci: ============================================
For now, disable CMDQ support on the imx8qm/imx8qxp/imx8mm until the
issue is found and resolved.
Fixes: bb6e358169bf6 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Fixes: cde5e8e9ff146 ("mmc: sdhci-esdhc-imx: Add an new esdhc_soc_data for i.MX8MM")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20211103165415.2016-1-tharvey@gateworks.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0eab756f8821d255016c63bb55804c429ff4bdb1 upstream.
There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2abbf36 ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce5f6c2c9b0fcb4094f8e162cfd37fb4294204f7 ]
The 'reg_vmmc' regulator is enabled in the probe. It is never disabled.
Neither in the error handling path of the probe nor in the remove
function.
Register a devm_action to disable it when needed.
Fixes: 4dc5a79f1350 ("mmc: mxs-mmc: enable regulator for mmc slot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d806e334d0390502cd2a820ad33d65d7f9bba618 ]
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263a6 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e0e7bd38b1ec7f9e5d18725ad41828be4e09859 ]
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8105c2abbf36296bf38ca44f55ee45d160db476a ]
The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.
Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 162079f2dccd02cb4b6654defd32ca387dd6d4d4 ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 43592c8736e84025d7a45e61a46c3fa40536a364 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43e5fee317f4b0a48992b8b07935b1a3ac20ce84 upstream.
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
circuit
commit 9af372dc70e9fdcbb70939dac75365e7b88580b4 upstream.
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4217d07b9fb328751f877d3bd9550122014860a2 upstream.
On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.
[ 1.436599] ------------[ cut here ]------------
[ 1.436606] mmc0: Invalid vdd 0x17
[ 1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4
[ 1.436655] Modules linked in:
[ 1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G W 5.15.0-rc1+ #137
[ 1.436669] Hardware name: Thundercomm TurboX CM2290 (DT)
[ 1.436674] Workqueue: events_unbound async_run_entry_fn
[ 1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4
[ 1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4
[ 1.436703] sp : ffff800010803a60
[ 1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70
[ 1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280
[ 1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000
[ 1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020
[ 1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff
[ 1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc
[ 1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60
[ 1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159
[ 1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff
[ 1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80
[ 1.436797] Call trace:
[ 1.436800] sdhci_set_power_noreg+0x168/0x2b4
[ 1.436805] sdhci_set_ios+0xa0/0x7fc
[ 1.436811] mmc_power_up.part.0+0xc4/0x164
[ 1.436818] mmc_start_host+0xa0/0xb0
[ 1.436824] mmc_add_host+0x60/0x90
[ 1.436830] __sdhci_add_host+0x174/0x330
[ 1.436836] sdhci_msm_probe+0x7c0/0x920
[ 1.436842] platform_probe+0x68/0xe0
[ 1.436850] really_probe.part.0+0x9c/0x31c
[ 1.436857] __driver_probe_device+0x98/0x144
[ 1.436863] driver_probe_device+0xc8/0x15c
[ 1.436869] __device_attach_driver+0xb4/0x120
[ 1.436875] bus_for_each_drv+0x78/0xd0
[ 1.436881] __device_attach_async_helper+0xac/0xd0
[ 1.436888] async_run_entry_fn+0x34/0x110
[ 1.436895] process_one_work+0x1d0/0x354
[ 1.436903] worker_thread+0x13c/0x470
[ 1.436910] kthread+0x150/0x160
[ 1.436915] ret_from_fork+0x10/0x20
[ 1.436923] ---[ end trace fcfac44cb045c3a8 ]---
Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to
SDHCI_POWER_330 as well.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211004024935.15326-1-shawn.guo@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 697542bceae51f7620af333b065dd09d213629fb upstream.
Even though there are candiates value if can't find best value, it's
returned -EIO. It's not proper behavior.
If there is not best value, use a first candiate value to work eMMC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Cc: stable@vger.kernel.org
Fixes: c537a1c5ff63 ("mmc: dw_mmc: exynos: add variable delay tuning sequence")
Link: https://lore.kernel.org/r/20211022082106.1557-1-jh80.chung@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8a1ff65927080278e6826f797b7c197fb2611a6 upstream.
We must enable clock before cqhci init, because crypto needs read
information from CQHCI registers, otherwise, it will hang in MediaTek mmc
host controller.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Acked-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20211028022049.22129-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92b18252b91de567cd875f2e84722b10ab34ee28 upstream.
While mmc0 enter suspend state, we need halt CQE to send legacy cmd(flush
cache) and disable cqe, for resume back, we enable CQE and not clear HALT
state.
In this case MediaTek mmc host controller will keep the value for HALT
state after CQE disable/enable flow, so the next CQE transfer after resume
will be timeout due to CQE is in HALT state, the log as below:
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: timeout for tag 2
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: ============ CQHCI REGISTER DUMP ===========
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Caps: 0x100020b6 | Version: 0x00000510
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Config: 0x00001103 | Control: 0x00000001
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: TDL base: 0xfd05f000 | TDL up32: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Doorbell: 0x8000203c | TCN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Task clr: 0x00000000 | SSC1: 0x00001000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQP: 0x00000000 | CRNQDUN: 0x00000000
<4>.(4)[318:kworker/4:1H]mmc0: cqhci: CRNQIS: 0x00000000 | CRNQIE: 0x00000000
This change check HALT state after CQE enable, if CQE is in HALT state, we
will clear it.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host")
Link: https://lore.kernel.org/r/20211026070812.9359-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c8171929116cc23f74743d99251eedadf62341a upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025115608.5287-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30d4b990ec644e8bd49ef0a2f074fabc0d189e53 upstream.
Replace while loop with read_poll_timeout().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210924082851.2132068-3-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af467fad78f03a42de8b72190f6a595366b870db upstream.
Datasheet specifies that at the end of calibration the SDMMC_CALCR_EN
bit will be cleared. No commands should be send before calibration is
done.
Fixes: dbdea70f71d67 ("mmc: sdhci-of-at91: fix CALCR register being rewritten")
Fixes: 727d836a375ad ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210924082851.2132068-2-claudiu.beznea@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a38a4d51c5055d0201542e5ea3c0cb287f6e223 upstream.
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e6c
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c22c ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e72a55f2e5ddcfb3dce0701caf925ce435b87682 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ]
At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.
Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c0b4e411a9b09748466ee06d2ae6772effa64dfb ]
SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c3ff0189d3bc9c03845fe37472c140f0fefd0c79 ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 522654d534d315d540710124c57b49ca22ac5f72 ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures at least if external TI SDMA is ever configured for sdhci.
For other external DMA cases, this is probably not currently an issue but
is still good to fix though.
Fixes: 18e762e3b7a7 ("mmc: sdhci: add support for using external DMA devices")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210810081644.19353-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 885814a97f5a1a2daf66bde5f2076f0bf632c174 ]
This reverts commit 419dd626e357e89fc9c4e3863592c8b38cfe1571.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e357 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 419dd626e357e89fc9c4e3863592c8b38cfe1571 ]
The controller doesn't seem to pick-up on clock changes, so set the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN flag to query the clock frequency
directly from the clock.
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-of |
