| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rx_chn->irq[] array is unsigned int but it should be signed for the
error handling to work. Also if k3_udma_glue_rx_get_irq() returns zero
then we should return -ENXIO instead of success.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/05282415-e7f4-42f3-99f8-32fde8f30936@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/page_pool_user.c
0b11b1c5c320 ("netdev: let netlink core handle -EMSGSIZE errors")
429679dcf7d9 ("page_pool: fix netlink dump stop/resume")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is now possible to disable BQL, but that causes the cpsw driver to break:
drivers/net/ethernet/ti/am65-cpsw-nuss.c:297:28: error: no member named 'dql' in 'struct netdev_queue'
297 | dql_avail(&netif_txq->dql),
There is already a helper function in net/sch_generic.h that could
be used to help here. Move its implementation into the common
linux/netdevice.h along with the other bql interfaces and change
both users over to the new interface.
Fixes: ea7f3cfaa588 ("net: bql: allow the config to be disabled")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the duplicate calls to prueth_emac_stop() and
prueth_cleanup_tx_chns() in emac_ndo_stop().
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clang-16 warns about the mismatched prototypes for the devm_* callbacks:
drivers/net/ethernet/ti/cpts.c:691:12: error: cast from 'void (*)(struct clk_hw *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
691 | (void(*)(void *))clk_hw_unregister_mux,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:406:34: note: expanded from macro 'devm_add_action_or_reset'
406 | __devm_add_action_or_reset(dev, action, data, #action)
| ^~~~~~
drivers/net/ethernet/ti/cpts.c:703:12: error: cast from 'void (*)(struct device_node *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
703 | (void(*)(void *))of_clk_del_provider,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:406:34: note: expanded from macro 'devm_add_action_or_reset'
406 | __devm_add_action_or_reset(dev, action, data, #action)
Use separate helper functions for this instead, using the expected prototypes
with a void* argument.
Fixes: a3047a81ba13 ("net: ethernet: ti: cpts: add support for ext rftclk selection")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PTP_1588_CLOCK=m and CONFIG_TI_ICSSG_PRUETH=y, there are
kconfig dependency warnings and build errors referencing PTP functions.
Fix these by making TI_ICSSG_PRUETH depend on PTP_1588_CLOCK_OPTIONAL.
Fixes these build errors and warnings:
WARNING: unmet direct dependencies detected for TI_ICSS_IEP
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PTP_1588_CLOCK_OPTIONAL [=m] && TI_PRUSS [=y]
Selected by [y]:
- TI_ICSSG_PRUETH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PRU_REMOTEPROC [=y] && ARCH_K3 [=y] && OF [=y] && TI_K3_UDMA_GLUE_LAYER [=y]
aarch64-linux-ld: drivers/net/ethernet/ti/icssg/icss_iep.o: in function `icss_iep_get_ptp_clock_idx':
icss_iep.c:(.text+0x1d4): undefined reference to `ptp_clock_index'
aarch64-linux-ld: drivers/net/ethernet/ti/icssg/icss_iep.o: in function `icss_iep_exit':
icss_iep.c:(.text+0xde8): undefined reference to `ptp_clock_unregister'
aarch64-linux-ld: drivers/net/ethernet/ti/icssg/icss_iep.o: in function `icss_iep_init':
icss_iep.c:(.text+0x176c): undefined reference to `ptp_clock_register'
Fixes: 186734c15886 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Md Danish Anwar <danishanwar@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240211061152.14696-1-rdunlap@infradead.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc09 ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a71313e ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9e0 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c9013880284d ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22af8 ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
1279f9d9dec2 ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw_new resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the TI CPSW switch module.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.
The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.
The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240105085530.14070-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add SW IRQ coalescing based on hrtimers for TX and RX data path which
can be enabled by ethtool commands:
- RX coalescing
ethtool -C eth1 rx-usecs 50
- TX coalescing can be enabled per TX queue
- by default enables coalesing for TX0
ethtool -C eth1 tx-usecs 50
- configure TX0
ethtool -Q eth0 queue_mask 1 --coalesce tx-usecs 100
- configure TX1
ethtool -Q eth0 queue_mask 2 --coalesce tx-usecs 100
- configure TX0 and TX1
ethtool -Q eth0 queue_mask 3 --coalesce tx-usecs 100 --coalesce tx-usecs 100
show configuration for TX0 and TX1:
ethtool -Q eth0 queue_mask 3 --show-coalesce
Comparing to gro_flush_timeout and napi_defer_hard_irqs, this patch
allows to enable IRQ coalesing for RX path separately.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver support for viewing / changing the MAC Merge sublayer
parameters and seeing the verification state machine's current state
via ethtool.
As hardware does not support interrupt notification for verification
events we resort to polling on link up. On link up we try a couple of
times for verification success and if unsuccessful then give up.
The Frame Preemption feature is described in the Technical Reference
Manual [1] in section:
12.3.1.4.6.7 Intersperced Express Traffic (IET – P802.3br/D2.0)
Due to Silicon Errata i2208 [2] we set limit min IET fragment size to
124 (excluding 4 bytes mCRC).
[1] AM62x TRM - https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
[2] AM62x Silicon Errata - https://www.ti.com/lit/er/sprz487c/sprz487c.pdf
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds MQPRIO Qdisc offload in full 'channel' mode which allows
not only setting up pri:tc mapping, but also configuring TX shapers
(rate-limiting) on external port FIFOs.
The MQPRIO Qdisc offload is expected to work with or without VLAN/priority
tagged packets.
The CPSW external Port FIFO has 8 Priority queues. The rate-limit can be
set for each of these priority queues. Which Priority queue a packet is
assigned to depends on PN_REG_TX_PRI_MAP register which maps header
priority to switch priority.
The header priority of a packet is assigned via the RX_PRI_MAP_REG which
maps packet priority to header priority.
The packet priority is either the VLAN priority (for VLAN tagged packets)
or the thread/channel offset.
For simplicity, we assign the same priority queue to all queues of a
Traffic Class so it can be rate-limited correctly.
Configuration example:
ethtool -L eth1 tx 5
ethtool --set-priv-flags eth1 p0-rx-ptype-rrobin off
tc qdisc add dev eth1 parent root handle 100: mqprio num_tc 3 \
map 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 hw 1 mode channel \
shaper bw_rlimit min_rate 0 100mbit 200mbit max_rate 0 101mbit 202mbit
tc qdisc replace dev eth2 handle 100: parent root mqprio num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@0 hw 1
ip link add link eth1 name eth1.100 type vlan id 100
ip link set eth1.100 type vlan egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
In the above example two ports share the same TX CPPI queue 0 for low
priority traffic. 3 traffic classes are defined for eth1 and mapped to:
TC0 - low priority, TX CPPI queue 0 -> ext Port 1 fifo0, no rate limit
TC1 - prio 2, TX CPPI queue 1 -> ext Port 1 fifo1, CIR=100Mbit/s, EIR=1Mbit/s
TC2 - prio 3, TX CPPI queue 2 -> ext Port 1 fifo2, CIR=200Mbit/s, EIR=2Mbit/s
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move register definitions to header file. No functional change.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move this code around to avoid forward declaration.
No functional change.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle offloading commands using switch-case in
am65_cpsw_setup_taprio().
Move checks to am65_cpsw_taprio_replace().
Use NL_SET_ERR_MSG_MOD for error messages.
Change error message from "Failed to set cycle time extension"
to "cycle time extension not supported"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will use this Kconfig option to not only enable TAS/EST offload
but also other QoS features like Multiqueue priority descriptors
and MAC-Merge/Frame Preemption. TI_AM65_CPSW_QOS seems a more
appropriate Kconfig option name than TI_AM65_CPSW_TAS.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Build am65-cpsw-qos only if CONFIG_TI_AM65_CPSW_TAS is enabled.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The errata i2329 affects all the currently available silicon revisions of
AM62x, AM64x, AM65x, J7200, J721E and J721S2. So remove the revision
string from the SoC list.
The silicon revisions affected by the errata i2329 can be found under
the MDIO module in the "Advisories by Modules" section of each
SoC errata document listed below
AM62x: https://www.ti.com/lit/er/sprz487c/sprz487c.pdf
AM64X: https://www.ti.com/lit/er/sprz457g/sprz457g.pdf
AM65X: https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
J7200: https://www.ti.com/lit/er/sprz491d/sprz491d.pdf
J721E: https://www.ti.com/lit/er/sprz455d/sprz455d.pdf
J721S2: https://www.ti.com/lit/er/sprz530b/sprz530b.pdf
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20231201132033.29576-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Replace the error path returning a non-zero value by an error message
and a comment that there is more to do. With that this patch results in
no change of behaviour in this driver apart from improving the error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
k3_udma_glue_enable_rx/tx_chn returns error code on failure.
Bail out on error while enabling TX/RX channel.
In the error path, clean up the RX descriptors and SKBs.
Get rid of kmemleak_not_leak() as it seems unnecessary now.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
am65-cpsw supports 8 TX hardware queues. Set this as default.
The rationale is that some am65-cpsw devices can have up to 4 ethernet
ports. If the number of TX channels have to be changed then all
interfaces have to be brought down and up as the old default of 1
TX channel is too restrictive for any mqprio/taprio usage.
Another reason for this change is to allow testing using
kselftest:net/forwarding:ethtool_mm.sh out of the box.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-arrange am65_cpsw_nuss_rx_cleanup(), am65_cpsw_nuss_xmit_free() and
am65_cpsw_nuss_tx_cleanup() to avoid forward declaration.
No functional change.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gets 'ethtool -S eth0 --groups eth-mac' command to work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were just continuing in this case, surely not desired.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Analogously to prueth_remove, just also taking care for NULL'ing the
iep pointers.
Fixes: 186734c15886 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Fixes: 443a2367ba3c ("net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently icss_iep_set_counter() writes the upper 32-bits of the
counter value to both the lower and upper counter registers, so
fix this by writing the appropriate value to the lower register.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Link: https://lore.kernel.org/r/20231107120037.1513546-1-diogo.ivo@siemens.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The rx_pause flag says that whether we support receiving Pause frames.
When a Pause frame is received TX is delayed for some time. This is TX
flow control. In the same manner tx_pause is actually RX flow control.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is a device tree entry called "local-mac-address"
which can be filled by the bootloader or manually set.This is
useful when the user does not want to use the MAC address
programmed into the SoC.
Currently, the davinci_emac reads the MAC from the DT, copies
it from pdata->mac_addr to priv->mac_addr, then blindly overwrites
it by reading from registers in the SoC, and falls back to a
random MAC if it's still not valid. This completely ignores any
MAC address in the device tree.
In order to use the local-mac-address, check to see if the contents
of priv->mac_addr are valid before falling back to reading from the
SoC when the MAC address is not valid.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231022151911.4279-1-aford173@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Helps identifying the ports in udev rules e.g.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/895ae9c1-b6dd-4a97-be14-6f2b73c7b2b5@siemens.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
net/mac80211/key.c
02e0e426a2fb ("wifi: mac80211: fix error path key leak")
2a8b665e6bcc ("wifi: mac80211: remove key_mtx")
7d6904bf26b9 ("Merge wireless into wireless-next")
https://lore.kernel.org/all/20231012113648.46eea5ec@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/ti/Kconfig
a602ee3176a8 ("net: ethernet: ti: Fix mixed module-builtin object")
98bdeae9502b ("net: cpmac: remove driver to prepare for platform removal")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bitmasks for EMAC_PORT_DISABLE and EMAC_PORT_FORWARD r30 commands are
wrong in the driver.
Update the bitmasks of these commands to the correct ones as used by the
ICSSG firmware. These bitmasks are backwards compatible and work with
any ICSSG firmware version.
Fixes: e9b4ece7d74b ("net: ti: icssg-prueth: Add Firmware config and classification APIs.")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231018150715.3085380-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With CONFIG_TI_K3_AM65_CPSW_NUSS=y and CONFIG_TI_ICSSG_PRUETH=m,
k3-cppi-desc-pool.o is linked to a module and also to vmlinux even though
the expected CFLAGS are different between builtins and modules.
The build system is complaining about the following:
k3-cppi-desc-pool.o is added to multiple modules: icssg-prueth
ti-am65-cpsw-nuss
Introduce the new module, k3-cppi-desc-pool, to provide the common
functions to ti-am65-cpsw-nuss and icssg-prueth.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231018064936.3146846-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Other implementations of .*get_drvinfo also use strscpy so this patch
brings keystone_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-ethernet-ti-netcp_ethss-c-v1-1-93142e620864@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ICSSG HW stats on TX side considers 8 preamble bytes as data bytes. Due
to this the tx_bytes of ICSSG interface doesn't match the rx_bytes of the
link partner. There is no public errata available yet.
As a workaround to fix this, decrease tx_bytes by 8 bytes for every tx
frame.
Fixes: c1e10d5dc7a1 ("net: ti: icssg-prueth: Add ICSSG Stats")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231012064626.977466-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AR7 is going to be removed from the Kernel, so remove its networking
support in form of the cpmac driver. This allows us to remove the
platform because this driver includes a platform specific header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/all/20230922061530.3121-6-wsa+renesas@sang-engineering.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (or adjacent changes of note).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xdp_do_flush_map() is deprecated and new code should use xdp_do_flush()
instead.
Replace xdp_do_flush_map() with xdp_do_flush().
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: John Crispin <john@phrozen.org>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Cc: Shenwei Wang <shenwei.wang@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230908143215.869913-2-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
