summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2021-10-20ionic: don't remove netdev->dev_addr when syncing uc listShannon Nelson1-0/+4
commit 5c976a56570f29aaf4a2f9a1bf99789c252183c9 upstream. Bridging, and possibly other upper stack gizmos, adds the lower device's netdev->dev_addr to its own uc list, and then requests it be deleted when the upper bridge device is removed. This delete request also happens with the bridging vlan_filtering is enabled and then disabled. Bonding has a similar behavior with the uc list, but since it also uses set_mac to manage netdev->dev_addr, it doesn't have the same the failure case. Because we store our netdev->dev_addr in our uc list, we need to ignore the delete request from dev_uc_sync so as to not lose the address and all hope of communicating. Note that ndo_set_mac_address is expressly changing netdev->dev_addr, so no limitation is set there. Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skbVladimir Oltean1-3/+3
commit 9fde506e0c53b8309f69b18b4b8144c544b4b3b1 upstream. When skb_match is NULL, it means we received a PTP IRQ for a timestamp ID that the kernel has no idea about, since there is no skb in the timestamping queue with that timestamp ID. This is a grave error and not something to just "continue" over. So print a big warning in case this happens. Also, move the check above ocelot_get_hwtimestamp(), there is no point in reading the full 64-bit current PTP time if we're not going to do anything with it anyway for this skb. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20nfp: flow_offload: move flow_indr_dev_register from app init to app startBaowen Zheng1-5/+14
commit 60d950f443a52d950126ad664fbd4a1eb8353dc9 upstream. In commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation"), it adds a process to trigger the callback to setup the bo callback when the driver regists a callback. In our current implement, we are not ready to run the callback when nfp call the function flow_indr_dev_register, then there will be error message as: kernel: Oops: 0000 [#1] SMP PTI kernel: CPU: 0 PID: 14119 Comm: kworker/0:0 Tainted: G kernel: Workqueue: events work_for_cpu_fn kernel: RIP: 0010:nfp_flower_indr_setup_tc_cb+0x258/0x410 kernel: RSP: 0018:ffffbc1e02c57bf8 EFLAGS: 00010286 kernel: RAX: 0000000000000000 RBX: ffff9c761fabc000 RCX: 0000000000000001 kernel: RDX: 0000000000000001 RSI: fffffffffffffff0 RDI: ffffffffc0be9ef1 kernel: RBP: ffffbc1e02c57c58 R08: ffffffffc08f33aa R09: ffff9c6db7478800 kernel: R10: 0000009c003f6e00 R11: ffffbc1e02800000 R12: ffffbc1e000d9000 kernel: R13: ffffbc1e000db428 R14: ffff9c6db7478800 R15: ffff9c761e884e80 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: fffffffffffffff0 CR3: 00000009e260a004 CR4: 00000000007706f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: PKRU: 55555554 kernel: Call Trace: kernel: ? flow_indr_dev_register+0xab/0x210 kernel: ? __cond_resched+0x15/0x30 kernel: ? kmem_cache_alloc_trace+0x44/0x4b0 kernel: ? nfp_flower_setup_tc+0x1d0/0x1d0 [nfp] kernel: flow_indr_dev_register+0x158/0x210 kernel: ? tcf_block_unbind+0xe0/0xe0 kernel: nfp_flower_init+0x40b/0x650 [nfp] kernel: nfp_net_pci_probe+0x25f/0x960 [nfp] kernel: ? nfp_rtsym_read_le+0x76/0x130 [nfp] kernel: nfp_pci_probe+0x6a9/0x820 [nfp] kernel: local_pci_probe+0x45/0x80 So we need to call flow_indr_dev_register in app start process instead of init stage. Fixes: 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation") Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20211012124850.13025-1-louis.peens@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20qed: Fix missing error code in qed_slowpath_start()chongjiapeng1-0/+1
commit a5a14ea7b4e55604acb0dc9d88fdb4cb6945bc77 upstream. The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'rc'. Eliminate the follow smatch warning: drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start() warn: missing error code 'rc'. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20mlxsw: thermal: Fix out-of-bounds memory accessesIdo Schimmel1-47/+5
commit 332fdf951df8b870e3da86b122ae304e2aabe88c upstream. Currently, mlxsw allows cooling states to be set above the maximum cooling state supported by the driver: # cat /sys/class/thermal/thermal_zone2/cdev0/type mlxsw_fan # cat /sys/class/thermal/thermal_zone2/cdev0/max_state 10 # echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state # echo $? 0 This results in out-of-bounds memory accesses when thermal state transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the transition table is accessed with a too large index (state) [1]. According to the thermal maintainer, it is the responsibility of the driver to reject such operations [2]. Therefore, return an error when the state to be set exceeds the maximum cooling state supported by the driver. To avoid dead code, as suggested by the thermal maintainer [3], partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") that tried to interpret these invalid cooling states (above the maximum) in a special way. The cooling levels array is not removed in order to prevent the fans going below 20% PWM, which would cause them to get stuck at 0% PWM. [1] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290 Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5 CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122 Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016 Workqueue: events_freezable_power_ thermal_zone_device_check Call Trace: dump_stack_lvl+0x8b/0xb3 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b thermal_cooling_device_stats_update+0x271/0x290 __thermal_cdev_update+0x15e/0x4e0 thermal_cdev_update+0x9f/0xe0 step_wise_throttle+0x770/0xee0 thermal_zone_device_update+0x3f6/0xdf0 process_one_work+0xa42/0x1770 worker_thread+0x62f/0x13e0 kthread+0x3ee/0x4e0 ret_from_fork+0x1f/0x30 Allocated by task 1: kasan_save_stack+0x1b/0x40 __kasan_kmalloc+0x7c/0x90 thermal_cooling_device_setup_sysfs+0x153/0x2c0 __thermal_cooling_device_register.part.0+0x25b/0x9c0 thermal_cooling_device_register+0xb3/0x100 mlxsw_thermal_init+0x5c5/0x7e0 __mlxsw_core_bus_device_register+0xcb3/0x19c0 mlxsw_core_bus_device_register+0x56/0xb0 mlxsw_pci_probe+0x54f/0x710 local_pci_probe+0xc6/0x170 pci_device_probe+0x2b2/0x4d0 really_probe+0x293/0xd10 __driver_probe_device+0x2af/0x440 driver_probe_device+0x51/0x1e0 __driver_attach+0x21b/0x530 bus_for_each_dev+0x14c/0x1d0 bus_add_driver+0x3ac/0x650 driver_register+0x241/0x3d0 mlxsw_sp_module_init+0xa2/0x174 do_one_initcall+0xee/0x5f0 kernel_init_freeable+0x45a/0x4de kernel_init+0x1f/0x210 ret_from_fork+0x1f/0x30 The buggy address belongs to the object at ffff8881052f7800 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 1016 bytes inside of 1024-byte region [ffff8881052f7800, ffff8881052f7c00) The buggy address belongs to the page: page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0 head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0 flags: 0x200000000010200(slab|head|node=0|zone=2) raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0 raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/ [3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/ CC: Daniel Lezcano <daniel.lezcano@linaro.org> Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone") Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20ethernet: s2io: fix setting mac address during resumeArnd Bergmann1-1/+1
commit 40507e7aada8422c38aafa0c8a1a09e4623c712a upstream. After recent cleanups, gcc started warning about a suspicious memcpy() call during the s2io_io_resume() function: In function '__dev_addr_set', inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2, inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2, inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7: arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict] 182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n) | ^~~~~~~~~~~~~~~~~~~~~~~~~ include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy' 4648 | memcpy(dev->dev_addr, addr, len); | ^~~~~~ What apparently happened is that an old cleanup changed the calling conventions for s2io_set_mac_addr() from taking an ethernet address as a character array to taking a struct sockaddr, but one of the callers was not changed at the same time. Change it to instead call the low-level do_s2io_prog_unicast() function that still takes the old argument type. Fixes: 2fd376884558 ("S2io: Added support set_mac_address driver entry point") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net: encx24j600: check error in devm_regmap_init_encx24j600Nanyong Sun3-5/+14
commit f03dca0c9e2297c84a018e306f8a9cd534ee4287 upstream. devm_regmap_init may return error which caused by like out of memory, this will results in null pointer dereference later when reading or writing register: general protection fault in encx24j600_spi_probe KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097] CPU: 0 PID: 286 Comm: spi-encx24j600- Not tainted 5.15.0-rc2-00142-g9978db750e31-dirty #11 9c53a778c1306b1b02359f3c2bbedc0222cba652 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:regcache_cache_bypass drivers/base/regmap/regcache.c:540 Code: 54 41 89 f4 55 53 48 89 fb 48 83 ec 08 e8 26 94 a8 fe 48 8d bb a0 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 03 00 00 4c 8d ab b0 00 00 00 48 8b ab a0 00 RSP: 0018:ffffc900010476b8 EFLAGS: 00010207 RAX: dffffc0000000000 RBX: fffffffffffffff4 RCX: 0000000000000000 RDX: 0000000000000012 RSI: ffff888002de0000 RDI: 0000000000000094 RBP: ffff888013c9a000 R08: 0000000000000000 R09: fffffbfff3f9cc6a R10: ffffc900010476e8 R11: fffffbfff3f9cc69 R12: 0000000000000001 R13: 000000000000000a R14: ffff888013c9af54 R15: ffff888013c9ad08 FS: 00007ffa984ab580(0000) GS:ffff88801fe00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055a6384136c8 CR3: 000000003bbe6003 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: encx24j600_spi_probe drivers/net/ethernet/microchip/encx24j600.c:459 spi_probe drivers/spi/spi.c:397 really_probe drivers/base/dd.c:517 __driver_probe_device drivers/base/dd.c:751 driver_probe_device drivers/base/dd.c:782 __device_attach_driver drivers/base/dd.c:899 bus_for_each_drv drivers/base/bus.c:427 __device_attach drivers/base/dd.c:971 bus_probe_device drivers/base/bus.c:487 device_add drivers/base/core.c:3364 __spi_add_device drivers/spi/spi.c:599 spi_add_device drivers/spi/spi.c:641 spi_new_device drivers/spi/spi.c:717 new_device_store+0x18c/0x1f1 [spi_stub 4e02719357f1ff33f5a43d00630982840568e85e] dev_attr_store drivers/base/core.c:2074 sysfs_kf_write fs/sysfs/file.c:139 kernfs_fop_write_iter fs/kernfs/file.c:300 new_sync_write fs/read_write.c:508 (discriminator 4) vfs_write fs/read_write.c:594 ksys_write fs/read_write.c:648 do_syscall_64 arch/x86/entry/common.c:50 entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:113 Add error check in devm_regmap_init_encx24j600 to avoid this situation. Fixes: 04fbfce7a222 ("net: Microchip encx24j600 driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Nanyong Sun <sunnanyong@huawei.com> Link: https://lore.kernel.org/r/20211012125901.3623144-1-sunnanyong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net: stmmac: fix get_hw_feature() on old hardwareHerve Codina4-9/+22
commit 075da584bae2da6a37428d59a477b6bdad430ac3 upstream. Some old IPs do not provide the hardware feature register. On these IPs, this register is read 0x00000000. In old driver version, this feature was handled but a regression came with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function"). Indeed, this commit removes the return value in dma->get_hw_feature(). This return value was used to indicate the validity of retrieved information and used later on in stmmac_hw_init() to override priv->plat data if this hardware feature were valid. This patch restores the return code in ->get_hw_feature() in order to indicate the hardware feature validity and override priv->plat data only if this hardware feature is valid. Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function") Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net/mlx5e: Mutually exclude RX-FCS and RX-port-timestampAya Levin1-5/+52
commit 0bc73ad46a76ed6ece4dcacb28858e7b38561e1c upstream. Due to current HW arch limitations, RX-FCS (scattering FCS frame field to software) and RX-port-timestamp (improved timestamp accuracy on the receive side) can't work together. RX-port-timestamp is not controlled by the user and it is enabled by default when supported by the HW/FW. This patch sets RX-port-timestamp opposite to RX-FCS configuration. Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error pathValentine Fatiev1-4/+3
commit 94b960b9deffc02fc0747afc01f72cc62ab099e3 upstream. Prior to this patch in case mlx5_core_destroy_cq() failed it returns without completing all destroy operations and that leads to memory leak. Instead, complete the destroy flow before return error. Also move mlx5_debug_cq_remove() to the beginning of mlx5_core_destroy_cq() to be symmetrical with mlx5_core_create_cq(). kmemleak complains on: unreferenced object 0xc000000038625100 (size 64): comm "ethtool", pid 28301, jiffies 4298062946 (age 785.380s) hex dump (first 32 bytes): 60 01 48 94 00 00 00 c0 b8 05 34 c3 00 00 00 c0 `.H.......4..... 02 00 00 00 00 00 00 00 00 db 7d c1 00 00 00 c0 ..........}..... backtrace: [<000000009e8643cb>] add_res_tree+0xd0/0x270 [mlx5_core] [<00000000e7cb8e6c>] mlx5_debug_cq_add+0x5c/0xc0 [mlx5_core] [<000000002a12918f>] mlx5_core_create_cq+0x1d0/0x2d0 [mlx5_core] [<00000000cef0a696>] mlx5e_create_cq+0x210/0x3f0 [mlx5_core] [<000000009c642c26>] mlx5e_open_cq+0xb4/0x130 [mlx5_core] [<0000000058dfa578>] mlx5e_ptp_open+0x7f4/0xe10 [mlx5_core] [<0000000081839561>] mlx5e_open_channels+0x9cc/0x13e0 [mlx5_core] [<0000000009cf05d4>] mlx5e_switch_priv_channels+0xa4/0x230 [mlx5_core] [<0000000042bbedd8>] mlx5e_safe_switch_params+0x14c/0x300 [mlx5_core] [<0000000004bc9db8>] set_pflag_tx_port_ts+0x9c/0x160 [mlx5_core] [<00000000a0553443>] mlx5e_set_priv_flags+0xd0/0x1b0 [mlx5_core] [<00000000a8f3d84b>] ethnl_set_privflags+0x234/0x2d0 [<00000000fd27f27c>] genl_family_rcv_msg_doit+0x108/0x1d0 [<00000000f495e2bb>] genl_family_rcv_msg+0xe4/0x1f0 [<00000000646c5c2c>] genl_rcv_msg+0x78/0x120 [<00000000d53e384e>] netlink_rcv_skb+0x74/0x1a0 Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Valentine Fatiev <valentinef@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net: korina: select CRC32Vegard Nossum1-0/+1
commit 427f974d9727ca681085ddcd0530c97ab5811ae0 upstream. Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/net/ethernet/korina.o: in function `korina_multicast_list': korina.c:(.text+0x1af): undefined reference to `crc32_le' Fixes: ef11291bcd5f9 ("Add support the Korina (IDT RC32434) Ethernet MAC") Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Florian fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20211012152509.21771-1-vegard.nossum@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-20net: arc: select CRC32Vegard Nossum1-0/+1
commit e599ee234ad4fdfe241d937bbabd96e0d8f9d868 upstream. Fix the following build/link error by adding a dependency on the CRC32 routines: ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode': emac_main.c:(.text+0xb11): undefined reference to `crc32_le' The crc32_le() call comes through the ether_crc_le() call in arc_emac_set_rx_mode(). [v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing, but the error comes from emac_main.o, which is part of the arc_emac module, which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is different from emac_arc...] Fixes: 775dd682e2b0ec ("arc_emac: implement promiscuous mode and multicast filtering") Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Link: https://lore.kernel.org/r/20211012093446.1575-1-vegard.nossum@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-10-17net: sun: SUNVNET_COMMON should depend on INETRandy Dunlap1-0/+1
[ Upstream commit 103bde372f084206c6972be543ecc247ebbff9f3 ] When CONFIG_INET is not set, there are failing references to IPv4 functions, so make this driver depend on INET. Fixes these build errors: sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_start_xmit_common': sunvnet_common.c:(.text+0x1a68): undefined reference to `__icmp_send' sparc64-linux-ld: drivers/net/ethernet/sun/sunvnet_common.o: in function `sunvnet_poll_common': sunvnet_common.c:(.text+0x358c): undefined reference to `ip_send_check' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Aaron Young <aaron.young@oracle.com> Cc: Rashmi Narasimhan <rashmi.narasimhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13i40e: Fix freeing of uninitialized misc IRQ vectorSylwester Dziedziuch1-1/+2
[ Upstream commit 2e5a20573a926302b233b0c2e1077f5debc7ab2e ] When VSI set up failed in i40e_probe() as part of PF switch set up driver was trying to free misc IRQ vectors in i40e_clear_interrupt_scheme and produced a kernel Oops: Trying to free already-free IRQ 266 WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300 Workqueue: events work_for_cpu_fn RIP: 0010:__free_irq+0x9a/0x300 Call Trace: ? synchronize_irq+0x3a/0xa0 free_irq+0x2e/0x60 i40e_clear_interrupt_scheme+0x53/0x190 [i40e] i40e_probe.part.108+0x134b/0x1a40 [i40e] ? kmem_cache_alloc+0x158/0x1c0 ? acpi_ut_update_ref_count.part.1+0x8e/0x345 ? acpi_ut_update_object_reference+0x15e/0x1e2 ? strstr+0x21/0x70 ? irq_get_irq_data+0xa/0x20 ? mp_check_pin_attr+0x13/0xc0 ? irq_get_irq_data+0xa/0x20 ? mp_map_pin_to_irq+0xd3/0x2f0 ? acpi_register_gsi_ioapic+0x93/0x170 ? pci_conf1_read+0xa4/0x100 ? pci_bus_read_config_word+0x49/0x70 ? do_pci_enable_device+0xcc/0x100 local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The problem is that at that point misc IRQ vectors were not allocated yet and we get a call trace that driver is trying to free already free IRQ vectors. Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED PF state before calling i40e_free_misc_vector. This state is set only if misc IRQ vectors were properly initialized. Fixes: c17401a1dd21 ("i40e: use separate state bit for miscellaneous IRQ setup") Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13i40e: fix endless loop under rtnlJiri Benc1-1/+1
[ Upstream commit 857b6c6f665cca9828396d9743faf37fd09e9ac3 ] The loop in i40e_get_capabilities can never end. The problem is that although i40e_aq_discover_capabilities returns with an error if there's a firmware problem, the returned error is not checked. There is a check for pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most firmware problems. When i40e_aq_discover_capabilities encounters a firmware problem, it will encounter the same problem on its next invocation. As the result, the loop becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking at the code, it can happen with a range of other firmware errors. I don't know what the correct behavior should be: whether the firmware should be retried a few times, or whether pf->hw.aq.asq_last_status should be always set to the encountered firmware error (but then it would be pointless and can be just replaced by the i40e_aq_discover_capabilities return value). However, the current behavior with an endless loop under the rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we explained the bug to them 7 months ago. This may not be the best possible fix but it's better than hanging the whole system on a firmware bug. Fixes: 56a62fc86895 ("i40e: init code and hardware support") Tested-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13gve: report 64bit tx_bytes counter from gve_handle_report_stats()Eric Dumazet1-2/+3
[ Upstream commit 17c37d748f2b122a95b6d0524d410302ff89a2b1 ] Each tx queue maintains a 64bit counter for bytes, there is no reason to truncate this to 32bit (or this has not been documented) Fixes: 24aeb56f2d38 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yangchun Fu <yangchun@google.com> Cc: Kuo Zhao <kuozhao@google.com> Cc: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13gve: fix gve_get_stats()Eric Dumazet1-4/+9
[ Upstream commit 2f57d4975fa027eabd35fdf23a49f8222ef3abf2 ] gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry() returns true. What is needed here is to sample values in temporary variables, and only use them after each loop is ended. Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Catherine Sullivan <csully@google.com> Cc: Sagi Shahar <sagis@google.com> Cc: Jon Olson <jonolson@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Luigi Rizzo <lrizzo@google.com> Cc: Jeroen de Borst <jeroendb@google.com> Cc: Tao Liu <xliutaox@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13gve: Avoid freeing NULL pointerTao Liu1-10/+17
[ Upstream commit 922aa9bcac92b3ab6a423526a8e785b35a60b441 ] Prevent possible crashes when cleaning up after unsuccessful initializations. Fixes: 893ce44df5658 ("gve: Add basic driver framework for Compute Engine Virtual NIC") Signed-off-by: Tao Liu <xliutaox@google.com> Signed-off-by: Catherine Sully <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13gve: Correct available tx qpl checkCatherine Sullivan1-1/+1
[ Upstream commit d03477ee10f4bc35d3573cf1823814378ef2dca2 ] The qpl_map_size is rounded up to a multiple of sizeof(long), but the number of qpls doesn't have to be. Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13net/mlx5: E-Switch, Fix double allocation of acl flow counterMoshe Shemesh2-5/+11
[ Upstream commit a586775f83bd729ad60b56352dbe067f4bb0beee ] Flow counter is allocated in eswitch legacy acl setting functions without checking if already allocated by previous setting. Add a check to avoid such double allocation. Fixes: 07bab9502641 ("net/mlx5: E-Switch, Refactor eswitch ingress acl codes") Fixes: ea651a86d468 ("net/mlx5: E-Switch, Refactor eswitch egress acl codes") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-13net/mlx5e: IPSEC RX, enable checksum completeRaed Salem1-6/+1
[ Upstream commit f9a10440f0b1f33faa792af26f4e9823a9b8b6a4 ] Currently in Rx data path IPsec crypto offloaded packets uses csum_none flag, so checksum is handled by the stack, this naturally have some performance/cpu utilization impact on such flows. As Nvidia NIC starting from ConnectX6DX provides checksum complete value out of the box also for such flows there is no sense in taking csum_none path, furthermore the stack (xfrm) have the method to handle checksum complete corrections for such flows i.e. IPsec trailer removal and consequently checksum value adjustment. Because of the above and in addition the ConnectX6DX is the first HW which supports IPsec crypto offload then it is safe to report csum complete for IPsec offloaded traffic. Fixes: b2ac7541e377 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload") Signed-off-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: fix always enable rx vlan filter problem after selftestGuangbin Huang1-2/+4
[ Upstream commit 27bf4af69fcb9845fb2f0076db5d562ec072e70f ] Currently, the rx vlan filter will always be disabled before selftest and be enabled after selftest as the rx vlan filter feature is fixed on in old device earlier than V3. However, this feature is not fixed in some new devices and it can be disabled by user. In this case, it is wrong if rx vlan filter is enabled after selftest. So fix it. Fixes: bcc26e8dc432 ("net: hns3: remove unused code in hns3_self_test()") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: reconstruct function hns3_self_testPeng Li1-37/+64
[ Upstream commit 4c8dab1c709c5a715bce14efdb8f4e889d86aa04 ] This patch reconstructs function hns3_self_test to reduce the code cycle complexity and make code more concise. Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: fix prototype warningHuazhong Tan1-1/+1
[ Upstream commit a1e144d7dc3c55aa4d451e3a23cd8f34cd65ee01 ] Correct a report warning in hns3_ethtool.c Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: fix show wrong state when add existing uc mac addressJian Shen1-10/+9
[ Upstream commit 108b3c7810e14892c4a1819b1d268a2c785c087c ] Currently, if function adds an existing unicast mac address, eventhough driver will not add this address into hardware, but it will return 0 in function hclge_add_uc_addr_common(). It will cause the state of this unicast mac address is ACTIVE in driver, but it should be in TO-ADD state. To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST if mac address is existing, and delete two error log to avoid printing them all the time after this modification. Fixes: 72110b567479 ("net: hns3: return 0 and print warning when hit duplicate MAC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: fix mixed flag HCLGE_FLAG_MQPRIO_ENABLE and HCLGE_FLAG_DCB_ENABLEJian Shen2-28/+10
[ Upstream commit 0472e95ffeac8e61259eec17ab61608c6b35599d ] HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is supposed to set when enable multiple TCs with ets. But the driver mixed the flags when updating the tm configuration. Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE too, so remove the unnecessary limitation. Fixes: 5a5c90917467 ("net: hns3: add support for tc mqprio offload") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: keep MAC pause mode when multiple TCs are enabledYonglong Liu1-1/+22
[ Upstream commit d78e5b6a6764cb6e83668806b63d74566db36399 ] Bellow HNAE3_DEVICE_VERSION_V3, MAC pause mode just support one TC, when enabled multiple TCs, force enable PFC mode. HNAE3_DEVICE_VERSION_V3 can support MAC pause mode on multiple TCs, so when enable multiple TCs, just keep MAC pause mode, and enable PFC mode just according to the user settings. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: hns3: do not allow call hns3_nic_net_open repeatedlyJian Shen1-0/+5
[ Upstream commit 5b09e88e1bf7fe86540fab4b5f3eece8abead39e ] hns3_nic_net_open() is not allowed to called repeatly, but there is no checking for this. When doing device reset and setup tc concurrently, there is a small oppotunity to call hns3_nic_net_open repeatedly, and cause kernel bug by calling napi_enable twice. The calltrace information is like below: [ 3078.222780] ------------[ cut here ]------------ [ 3078.230255] kernel BUG at net/core/dev.c:6991! [ 3078.236224] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 3078.243431] Modules linked in: hns3 hclgevf hclge hnae3 vfio_iommu_type1 vfio_pci vfio_virqfd vfio pv680_mii(O) [ 3078.258880] CPU: 0 PID: 295 Comm: kworker/u8:5 Tainted: G O 5.14.0-rc4+ #1 [ 3078.269102] Hardware name: , BIOS KpxxxFPGA 1P B600 V181 08/12/2021 [ 3078.276801] Workqueue: hclge hclge_service_task [hclge] [ 3078.288774] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--) [ 3078.296168] pc : napi_enable+0x80/0x84 tc qdisc sho[w 3d0e7v8 .e3t0h218 79] lr : hns3_nic_net_open+0x138/0x510 [hns3] [ 3078.314771] sp : ffff8000108abb20 [ 3078.319099] x29: ffff8000108abb20 x28: 0000000000000000 x27: ffff0820a8490300 [ 3078.329121] x26: 0000000000000001 x25: ffff08209cfc6200 x24: 0000000000000000 [ 3078.339044] x23: ffff0820a8490300 x22: ffff08209cd76000 x21: ffff0820abfe3880 [ 3078.349018] x20: 0000000000000000 x19: ffff08209cd76900 x18: 0000000000000000 [ 3078.358620] x17: 0000000000000000 x16: ffffc816e1727a50 x15: 0000ffff8f4ff930 [ 3078.368895] x14: 0000000000000000 x13: 0000000000000000 x12: 0000259e9dbeb6b4 [ 3078.377987] x11: 0096a8f7e764eb40 x10: 634615ad28d3eab5 x9 : ffffc816ad8885b8 [ 3078.387091] x8 : ffff08209cfc6fb8 x7 : ffff0820ac0da058 x6 : ffff0820a8490344 [ 3078.396356] x5 : 0000000000000140 x4 : 0000000000000003 x3 : ffff08209cd76938 [ 3078.405365] x2 : 0000000000000000 x1 : 0000000000000010 x0 : ffff0820abfe38a0 [ 3078.414657] Call trace: [ 3078.418517] napi_enable+0x80/0x84 [ 3078.424626] hns3_reset_notify_up_enet+0x78/0xd0 [hns3] [ 3078.433469] hns3_reset_notify+0x64/0x80 [hns3] [ 3078.441430] hclge_notify_client+0x68/0xb0 [hclge] [ 3078.450511] hclge_reset_rebuild+0x524/0x884 [hclge] [ 3078.458879] hclge_reset_service_task+0x3c4/0x680 [hclge] [ 3078.467470] hclge_service_task+0xb0/0xb54 [hclge] [ 3078.475675] process_one_work+0x1dc/0x48c [ 3078.481888] worker_thread+0x15c/0x464 [ 3078.487104] kthread+0x160/0x170 [ 3078.492479] ret_from_fork+0x10/0x18 [ 3078.498785] Code: c8027c81 35ffffa2 d50323bf d65f03c0 (d4210000) [ 3078.506889] ---[ end trace 8ebe0340a1b0fb44 ]--- Once hns3_nic_net_open() is excute success, the flag HNS3_NIC_STATE_DOWN will be cleared. So add checking for this flag, directly return when HNS3_NIC_STATE_DOWN is no set. Fixes: e888402789b9 ("net: hns3: call hns3_nic_net_open() while doing HNAE3_UP_CLIENT") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06ixgbe: Fix NULL pointer dereference in ixgbe_xdp_setupFeng Zhou2-3/+7
[ Upstream commit 513e605d7a9ce136886cb42ebb2c40e9a6eb6333 ] The ixgbe driver currently generates a NULL pointer dereference with some machine (online cpus < 63). This is due to the fact that the maximum value of num_xdp_queues is nr_cpu_ids. Code is in "ixgbe_set_rss_queues"". Here's how the problem repeats itself: Some machine (online cpus < 63), And user set num_queues to 63 through ethtool. Code is in the "ixgbe_set_channels", adapter->ring_feature[RING_F_FDIR].limit = count; It becomes 63. When user use xdp, "ixgbe_set_rss_queues" will set queues num. adapter->num_rx_queues = rss_i; adapter->num_tx_queues = rss_i; adapter->num_xdp_queues = ixgbe_xdp_queues(adapter); And rss_i's value is from f = &adapter->ring_feature[RING_F_FDIR]; rss_i = f->indices = f->limit; So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup", for (i = 0; i < adapter->num_rx_queues; i++) if (adapter->xdp_ring[i]->xsk_umem) It leads to panic. Call trace: [exception RIP: ixgbe_xdp+368] RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297 RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90 RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000 R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000 R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc 8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808 9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235 10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384 11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd 12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb 13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88 14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319 15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290 16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8 17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64 18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9 19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c So I fix ixgbe_max_channels so that it will not allow a setting of queues to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup, take the smaller value of num_rx_queues and num_xdp_queues. Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP") Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: ks8851: fix link errorArnd Bergmann2-4/+10
[ Upstream commit 51bb08dd04a05035a64504faa47651d36b0f3125 ] An object file cannot be built for both loadable module and built-in use at the same time: arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common': ks8851_common.c:(.text+0xf80): undefined reference to `__this_module' Change the ks8851_common code to be a standalone module instead, and use Makefile logic to ensure this is built-in if at least one of its two users is. Fixes: 797047f875b5 ("net: ks8851: Implement Parallel bus operations") Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/ Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06e100: fix buffer overrun in e100_get_regsJacob Keller1-6/+10
[ Upstream commit 51032e6f17ce990d06123ad7307f258c50d25aa7 ] The e100_get_regs function is used to implement a simple register dump for the e100 device. The data is broken into a couple of MAC control registers, and then a series of PHY registers, followed by a memory dump buffer. The total length of the register dump is defined as (1 + E100_PHY_REGS) * sizeof(u32) + sizeof(nic->mem->dump_buf). The logic for filling in the PHY registers uses a convoluted inverted count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This is actually one more than the supposed number of PHY registers. The memory dump buffer is then filled into the space at [2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past the total size. The end result is that we overrun the total buffer size allocated by the kernel, which could lead to a panic or other issues due to memory corruption. It is difficult to determine the actual total number of registers here. The only 8255x datasheet I could find indicates there are 28 total MDI registers. However, we're reading 29 here, and reading them in reverse! In addition, the ethtool e100 register dump interface appears to read the first PHY register to determine if the device is in MDI or MDIx mode. This doesn't appear to be documented anywhere within the 8255x datasheet. I can only assume it must be in register 28 (the extra register we're reading here). Lets not change any of the intended meaning of what we copy here. Just extend the space by 4 bytes to account for the extra register and continue copying the data out in the same order. Change the E100_PHY_REGS value to be the correct total (29) so that the total register dump size is calculated properly. Fix the offset for where we copy the dump buffer so that it doesn't overrun the total size. Re-write the for loop to use counting up instead of the convoluted down-counting. Correct the mdio_read offset to use the 0-based register offsets, but maintain the bizarre reverse ordering so that we have the ABI expected by applications like ethtool. This requires and additional subtraction of 1. It seems a bit odd but it makes the flow of assignment into the register buffer easier to follow. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06e100: fix length calculation in e100_get_regs_lenJacob Keller1-1/+5
[ Upstream commit 4329c8dc110b25d5f04ed20c6821bb60deff279f ] commit abf9b902059f ("e100: cleanup unneeded math") tried to simplify e100_get_regs_len and remove a double 'divide and then multiply' calculation that the e100_reg_regs_len function did. This change broke the size calculation entirely as it failed to account for the fact that the numbered registers are actually 4 bytes wide and not 1 byte. This resulted in a significant under allocation of the register buffer used by e100_get_regs. Fix this by properly multiplying the register count by u32 first before adding the size of the dump buffer. Fixes: abf9b902059f ("e100: cleanup unneeded math") Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-10-06net: enetc: fix the incorrect clearing of IF_MODE bitsVladimir Oltean1-2/+1
[ Upstream commit 325fd36ae76a6d089983b2d2eccb41237d35b221 ] The enetc phylink .mac_config handler intends to clear the IFMODE field (bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the other fields instead. For normal operation, the bug was inconsequential, due to the fact that we write the PM0_IF_MODE register in two stages, first in phylink .mac_config (which incorrectly cleared out a bunch of stuff), then we update the speed and duplex to the correct values in phylink .mac_link_up. Judging by the code (not tested), it looks like maybe loopback mode was broken, since this is one of the settings in PM0_IF_MODE which is incorrectly cleared. Fixes: c76a97218dcb ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode") Reported-by: Pavel Machek (CIP) <pavel@denx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-30net: i825xx: Use absolute_pointer for memcpy from fixed memory locationGuenter Roeck1-1/+1
[ Upstream commit dff2d13114f0beec448da9b3716204eb34b0cf41 ] gcc 11.x reports the following compiler warning/error. drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe': arch/m68k/include/asm/string.h:72:25: error: '__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread] Use absolute_pointer() to work around the problem. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2021-09-30net: stmmac: allow CSR clock of 300MHzJesper Nilsson1-1/+1
[ Upstream commit 08dad2f4d541fcfe5e7bfda72cc6314bbfd2802f ] The Synopsys Ethernet IP uses the CSR clock as a base clock for MDC. The divisor used is set in the MAC_MDIO_Address register field CR (Clock Rate) The divisor is there to change the CSR clock into a clock that falls below the IEEE 802.3 specified max frequency of 2.5MHz. If the CSR clock is 300MHz, the code falls back to using the reset value in the MAC_MDIO_Address register, as described in the comment above this code. However, 300MHz is actually an allowed value and the proper divider can be estimated quite easily (it's just 1Hz difference!) A CSR frequency of 300MHz with the maximum clock rate value of 0x5 (STMMAC_CSR_250_300M, a divisor of 124) gives somewhere around ~2.42MHz which is below the IEEE 802.3 specified maximum. For the ARTPEC-8 SoC, the CSR clock is this problematic 300MHz, and unfortunately, the reset-value of the MAC_MDIO_Address CR field is 0x0. This leads to a clock rate of zero and a divisor of 42, and gives an MDC frequency of ~7.14MHz. Allow CSR clock of 300MHz by making the comparison inclusive. Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha